illegal bandwith value, driver for Terratec Cinergy DT usb XS

The driver in linux kernel 2.6.24.2 for "Terratec Cinergy DT usb XS diversity" sets the reported bandwith outside the fe_bandwidth_t range. The value 0 (BANDWIDTH_8_MHZ) is replaced with 8000. Here is an example showing the problem...

Device: Terratec Cinergy DT usb xs diversity
Linux: 2.6.24.2 (modules: mt2266, dvb_usb_dib0700)
Firmware: dvb-usb-dib0700-1.10.fw

Received event for frontend 0

Status for frontend 0 is now:
0 (no signal)

Reported parameters for frontend 0 are now:
Frequency: 714000000 Hz
Inversion: AUTO (2)
Bandwidth: 8 (0)
High priority stream code rate: AUTO (9)
Low priority stream code rate: AUTO (9)
Constellation: QAM64 (3)
Transmission mode: AUTO (2)
Guard interval: AUTO (4)
Hierarchy information: AUTO (4)

Received event for frontend 0

Status for frontend 0 is now:
FE_HAS_SIGNAL (found something above the noise level) FE_HAS_CARRIER (found a DVB signal) FE_HAS_VITERBI (FEC is stable)
FE_HAS_SYNC (found sync bytes)
FE_HAS_LOCK (everything's working)

Reported parameters for frontend 0 are now:
Frequency: 714000000 Hz
Inversion: AUTO (2)
Bandwidth: ??? (8000)
High priority stream code rate: 2/3 (2)
Low priority stream code rate: 1/2 (1)
Constellation: QAM64 (3)
Transmission mode: 8K (1)
Guard interval: 1/8 (2)
Hierarchy information: NONE (0)

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

I also have a Terratec Cinergy DT XS diversity but can't get it working with the Cinergy CI usb, do you have any idea how I can make it work?

Hi Tero,

I also have a Terratec Cinergy DT XS diversity but can't get it working with the Cinergy CI usb, do you have any idea how I can make it work? By the way, they showed on CEBIT a EeePC with linux on it with the Cinergy XSS. They also said that they will release linux drivers for all of their tv tuners.

Hi,

Quoted 3 lines · Derk Dukker

Hi Tero,

I also have a Terratec Cinergy DT XS diversity but can't get it working

with

Quoted 2 lines

the Cinergy CI usb, do you have any idea how I can make it work? By the way, they showed on CEBIT a EeePC with linux on it with the

Cinergy

Quoted 1 line

XSS. They also said that they will release linux drivers for all of

their tv

Quoted 2 lines

tuners.

This was an eeePC with a Terratec Hybrid XS FM (Analog TV, Radio, DVB-T), Pinnacle also had an eeePC with a Pinnacle 330e (Analog TV and DVB-T) both Empia em28xx based.

Here's the 3liner installation instruction:
http://mcentral.de/pipermail/em28xx/2008-March/001320.html

Markus

Thank you very much Markus!!
Do you also have any idea how to get the Cinergy CI usb working? I live in Holland and most of the channels are encrypted, so I need to use the Cinergy CI usb but I can't find drivers/information anywhere.

I bought this in the firstplace for my playstation 3 with linux on it, I knew that support for CI was hard, but they said it would work with eyetv. So I thought, if it isn't working on linux it will on mac with eyetv. Everything works on my mac with eyetv except the CI usb :(