Skip to contentSkip to conversation

Linux 11-minute mode (RTC update)

DISCUSSION John Sigler 3 participants 4 messages Apr 4, 2008 – Apr 5, 2008

lore
Share & tools
lore
#0 lore raw

(Message also posted to comp.protocols.time.ntp and linux-kernel but since timers are involved, I figured I might have more luck here.)

Hello,

I run Linux kernel 2.6.22.1-rt9 and ntpd 4.2.4p0

# adjtimex --print
         mode: 0
       offset: 77
    frequency: -1309904
     maxerror: 493576
     esterror: 50
       status: 1
time_constant: 6
    precision: 1
    tolerance: 33554432
         tick: 10000
     raw time:  1207230744s 183249us = 1207230744.183249

In my setup, STA_UNSYNC (0x0040, clock unsynchronized) is 0.

Thus, ntp_synced() returns 1.

Thus the kernel should write the system time to the RTC every 11 minutes; but it does not.

The relevant code is in sync_cmos_clock()

http://lxr.linux.no/linux/kernel/time/ntp.c#L188

I've added several printk() to this function, and it appears that it is never called.

The relevant timer is defined with the following macro.

static DEFINE_TIMER(sync_cmos_timer, sync_cmos_clock, 0, 0);

which expands to

static struct timer_list sync_cmos_timer =
{
.function = sync_cmos_clock,

  .expires  = 0,
  .data     = 0,
  .base     = &boot_tvec_bases

};

The problem seems to be that this timer is never armed, to bootstrap the process. It seems there should be a call to mod_timer() somewhere.

do_adjtimex() calls notify_cmos_timer() unconditionally.

static void notify_cmos_timer(void)
{
if (no_sync_cmos_clock)

    mod_timer(&sync_cmos_timer, jiffies + 1);
}

What are the semantics of notify_cmos_timer?
What is it supposed to do?

And what is 'no_sync_cmos_clock' supposed to mean?
/* Disable the cmos update - used by virtualization and embedded */ int no_sync_cmos_clock __read_mostly;
Why would we (re)arm the timer when 'no_sync_cmos_clock' is true?

I'd be grateful for anyone sharing their knowledge.

Regards.

#1 lore raw
Quoted 54 lines · John Sigler

I run Linux kernel 2.6.22.1-rt9 and ntpd 4.2.4p0

# adjtimex --print
         mode: 0
       offset: 77
    frequency: -1309904
     maxerror: 493576
     esterror: 50
       status: 1
time_constant: 6
    precision: 1
    tolerance: 33554432
         tick: 10000
     raw time:  1207230744s 183249us = 1207230744.183249

In my setup, STA_UNSYNC (0x0040, clock unsynchronized) is 0.

Thus, ntp_synced() returns 1.

Thus the kernel should write the system time to the RTC every 11 minutes; but it does not.

The relevant code is in sync_cmos_clock()

http://lxr.linux.no/linux/kernel/time/ntp.c#L188

I've added several printk() to this function, and it appears that it is never called.

The relevant timer is defined with the following macro.

static DEFINE_TIMER(sync_cmos_timer, sync_cmos_clock, 0, 0);

which expands to

static struct timer_list sync_cmos_timer =
{
.function = sync_cmos_clock,

  .expires  = 0,
  .data     = 0,
  .base     = &boot_tvec_bases

};

The problem seems to be that this timer is never armed, to bootstrap the process. It seems there should be a call to mod_timer() somewhere.

do_adjtimex() calls notify_cmos_timer() unconditionally.

static void notify_cmos_timer(void)
{
if (no_sync_cmos_clock)

    mod_timer(&sync_cmos_timer, jiffies + 1);
}
Quoted 7 lines

What are the semantics of notify_cmos_timer?
What is it supposed to do?

And what is 'no_sync_cmos_clock' supposed to mean?
/* Disable the cmos update - used by virtualization and embedded */ int no_sync_cmos_clock __read_mostly;
Why would we (re)arm the timer when 'no_sync_cmos_clock' is true?

For those wondering what this "11-minute mode" is, I'll quote the man page for hwclock. ( http://linux.die.net/man/8/hwclock )

<quote>

Automatic Hardware Clock Synchronization By the Kernel

You should be aware of another way that the Hardware Clock is kept synchronized in some systems. The Linux kernel has a mode wherein it copies the System Time to the Hardware Clock every 11 minutes. This is a good mode to use when you are using something sophisticated like ntp to keep your System Time synchronized. (ntp is a way to keep your System Time synchronized either to a time server somewhere on the network or to a radio clock hooked up to your system. See RFC 1305).

This mode (we'll call it "11 minute mode") is off until something turns it on. The ntp daemon xntpd is one thing that turns it on. You can turn it off by running anything, including hwclock --hctosys, that sets the System Time the old fashioned way.

To see if it is on or off, use the command adjtimex --print and look at the value of "status". If the "64" bit of this number (expressed in binary) equal to 0, 11 minute mode is on. Otherwise, it is off.

If your system runs with 11 minute mode on, don't use hwclock --adjust or hwclock --hctosys. You'll just make a mess. It is acceptable to use a hwclock --hctosys at startup time to get a reasonable System Time until your system is able to set the System Time from the external source and start 11 minute mode.

</quote>

Apparently, drivers using one or more timer_lists typically arm the timer in their open or init function. My problem is: I don't think there is an init function for the NTP sub-system.

Regards.

#2 lore raw

Hi!

Quoted 86 lines
Quoted 54 lines

I run Linux kernel 2.6.22.1-rt9 and ntpd 4.2.4p0

# adjtimex --print
         mode: 0
       offset: 77
    frequency: -1309904
     maxerror: 493576
     esterror: 50
       status: 1
time_constant: 6
    precision: 1
    tolerance: 33554432
         tick: 10000
     raw time:  1207230744s 183249us = 1207230744.183249

In my setup, STA_UNSYNC (0x0040, clock unsynchronized) is 0.

Thus, ntp_synced() returns 1.

Thus the kernel should write the system time to the RTC every 11 minutes; but it does not.

The relevant code is in sync_cmos_clock()

http://lxr.linux.no/linux/kernel/time/ntp.c#L188

I've added several printk() to this function, and it appears that it is never called.

The relevant timer is defined with the following macro.

static DEFINE_TIMER(sync_cmos_timer, sync_cmos_clock, 0, 0);

which expands to

static struct timer_list sync_cmos_timer =
{
.function = sync_cmos_clock,

  .expires  = 0,
  .data     = 0,
  .base     = &boot_tvec_bases

};

The problem seems to be that this timer is never armed, to bootstrap the process. It seems there should be a call to mod_timer() somewhere.

do_adjtimex() calls notify_cmos_timer() unconditionally.

static void notify_cmos_timer(void)
{
if (no_sync_cmos_clock)

    mod_timer(&sync_cmos_timer, jiffies + 1);
}
Quoted 7 lines

What are the semantics of notify_cmos_timer?
What is it supposed to do?

And what is 'no_sync_cmos_clock' supposed to mean?
/* Disable the cmos update - used by virtualization and embedded */ int no_sync_cmos_clock __read_mostly;
Why would we (re)arm the timer when 'no_sync_cmos_clock' is true?

For those wondering what this "11-minute mode" is, I'll quote the man page for hwclock. ( http://linux.die.net/man/8/hwclock )

<quote>

Automatic Hardware Clock Synchronization By the Kernel

You should be aware of another way that the Hardware Clock is kept synchronized in some systems. The Linux kernel has a mode wherein it copies the System Time to the Hardware Clock every 11 minutes. This is a good mode to use when you are using something sophisticated like ntp to keep your System Time synchronized. (ntp is a way to keep your System Time synchronized either to a time server somewhere on the network or to a radio clock hooked up to your system. See RFC 1305).

This mode (we'll call it "11 minute mode") is off until something turns it on. The ntp daemon xntpd is one thing that turns it on. You can turn it off by running anything, including hwclock --hctosys, that sets the System Time the old fashioned way.

To see if it is on or off, use the command adjtimex --print and look at the value of "status". If the "64" bit of this number (expressed in binary) equal to 0, 11 minute mode is on. Otherwise, it is off.

Quoted 5 lines

If your system runs with 11 minute mode on, don't use hwclock --adjust or hwclock --hctosys. You'll just make a mess. It is acceptable to use a hwclock --hctosys at startup time to get a reasonable System Time until your system is able to set the System Time from the external source and start 11 minute mode.

Does that even belong to kernel?

If it is only useful with ntpd already running, ntpd should be able to do the RTC sync, too...

Plus, that automatically means that 11-minutes updates stop when ntpd dies for some reason...

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
#3 lore raw
In reply to John Sigler
Quoted 2 lines · John Sigler

[...]
I run Linux kernel 2.6.22.1-rt9 and ntpd 4.2.4p0

The bug you're describing appear to have been created & fixed last year by commits 82644459 and 298a5df4.

- FChE