Few more patches for Kumar's powerpc.git

index 4cc7800..0f3738e 100644
@@ -57,7 +57,8 @@ Table of Contents
       n) 4xx/Axon EMAC ethernet nodes
       o) Xilinx IP cores
       p) Freescale Synchronous Serial Interface
-	  q) USB EHCI controllers
+      q) USB EHCI controllers
+      r) Freescale General-purpose Timers Module
 
   VII - Marvell Discovery mv64[345]6x System Controller chips
     1) The /system-controller node

@@ -2825,6 +2826,37 @@ platforms are moved over to use the flattened-device-tree model.
 		   big-endian;
 	   };
 
+    r) Freescale General-purpose Timers Module
+
+    Required properties:
+      - compatible : should be
+        "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
+        "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
+        "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
+      - reg : should contain gtm registers location and length (0x40).
+      - interrupts : should contain four interrupts.
+      - interrupt-parent : interrupt source phandle.
+      - clock-frequency : specifies the frequency driving the timer.
+
+    Example:
+
+    timer@500 {
+    	compatible = "fsl,mpc8360-gtm", "fsl,gtm";
+    	reg = <0x500 0x40>;
+    	interrupts = <90 8 78 8 84 8 72 8>;
+    	interrupt-parent = <&ipic>;
+    	/* filled by u-boot */
+    	clock-frequency = <0>;
+    };
+
+    timer@440 {
+    	compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
+    	reg = <0x440 0x40>;
+    	interrupts = <12 13 14 15>;
+    	interrupt-parent = <&qeic>;
+    	/* filled by u-boot */
+    	clock-frequency = <0>;
+    };
 
 VII - Marvell Discovery mv64[345]6x System Controller chips
 ===========================================================

index 7f2f126..ad874e4 100644
@@ -525,6 +525,11 @@ config FSL_LBC
 	help
 	  Freescale Localbus support
 
+config FSL_GTM
+	bool
+	help
+	  Freescale General-purpose Timers support
+
 # Yes MCA RS/6000s exist but Linux-PPC does not currently support any
 config MCA
 	bool

index 6d386d0..9d3ddd2 100644
@@ -13,6 +13,7 @@ obj-$(CONFIG_MMIO_NVRAM)	+= mmio_nvram.o
 obj-$(CONFIG_FSL_SOC)		+= fsl_soc.o
 obj-$(CONFIG_FSL_PCI)		+= fsl_pci.o
 obj-$(CONFIG_FSL_LBC)		+= fsl_lbc.o
+obj-$(CONFIG_FSL_GTM)		+= fsl_gtm.o
 obj-$(CONFIG_RAPIDIO)		+= fsl_rio.o
 obj-$(CONFIG_TSI108_BRIDGE)	+= tsi108_pci.o tsi108_dev.o
 obj-$(CONFIG_QUICC_ENGINE)	+= qe_lib/

index adc6621..76ffbc4 100644
@@ -20,3 +20,7 @@ config UCC
 	bool
 	default y if UCC_FAST || UCC_SLOW
 
+config QE_USB
+	bool
+	help
+	  QE USB Host Controller support

index 874fe1a..e9ff888 100644
@@ -6,3 +6,4 @@ obj-$(CONFIG_QUICC_ENGINE)+= qe.o qe_ic.o qe_io.o
 obj-$(CONFIG_UCC)	+= ucc.o
 obj-$(CONFIG_UCC_SLOW)	+= ucc_slow.o
 obj-$(CONFIG_UCC_FAST)	+= ucc_fast.o
+obj-$(CONFIG_QE_USB)	+= usb.o

index 0f3738e..098f456 100644
@@ -1721,24 +1721,35 @@ platforms are moved over to use the flattened-device-tree model.
    information.
 
    Required properties:
-   - device_type : should be "par_io".
+   - #gpio-cells : should be "2".
+   - compatible : should be "fsl,<chip>-qe-pario-bank",
+     "fsl,mpc8323-qe-pario-bank".
    - reg : offset to the register set and its length.
-   - num-ports : number of Parallel I/O ports
+   - gpio-controller : node to identify gpio controllers.
 
-   Example:
-	par_io@1400 {
-		reg = <1400 100>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		device_type = "par_io";
-		num-ports = <7>;
-		ucc_pin@01 {
-			......
-		};
+   For example, two QE Par I/O banks:
+	qe_pio_a: gpio-controller@1400 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8360-qe-pario-bank",
+			     "fsl,mpc8323-qe-pario-bank";
+		reg = <0x1400 0x18>;
+		gpio-controller;
+	};
 
+	qe_pio_e: gpio-controller@1460 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8360-qe-pario-bank",
+			     "fsl,mpc8323-qe-pario-bank";
+		reg = <0x1460 0x18>;
+		gpio-controller;
+	};
 
    vi) Pin configuration nodes
 
+   NOTE: pin configuration nodes are obsolete. Usually, their existance
+         is an evidence of the firmware shortcomings. Such fixups are
+         better handled by the Linux board file, not the device tree.
+
    Required properties:
    - linux,phandle : phandle of this node; likely referenced by a QE
      device.

index 76ffbc4..4872fbb 100644
@@ -24,3 +24,11 @@ config QE_USB
 	bool
 	help
 	  QE USB Host Controller support
+
+config QE_GPIO
+	bool "QE GPIO support"
+	select GENERIC_GPIO
+	select HAVE_GPIO_LIB
+	help
+	  Say Y here if you're going to use hardware that connects to the
+	  QE GPIOs.

index e9ff888..f1855c1 100644
@@ -7,3 +7,4 @@ obj-$(CONFIG_UCC)	+= ucc.o
 obj-$(CONFIG_UCC_SLOW)	+= ucc_slow.o
 obj-$(CONFIG_UCC_FAST)	+= ucc_fast.o
 obj-$(CONFIG_QE_USB)	+= usb.o
+obj-$(CONFIG_QE_GPIO)	+= gpio.o

new file mode 100644
index 0000000..3402d26
@@ -0,0 +1,397 @@
+/*
+ * MPC8360E RDK Device Tree Source
+ *
+ * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2007-2008 MontaVista Software, Inc.
+ *
+ * Author: Anton Vorontsov <[email protected]>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "fsl,mpc8360rdk";
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		ethernet3 = &enet3;
+		pci0 = &pci0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8360@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <32>;
+			i-cache-line-size = <32>;
+			d-cache-size = <32768>;
+			i-cache-size = <32768>;
+			/* filled by u-boot */
+			timebase-frequency = <0>;
+			bus-frequency = <0>;
+			clock-frequency = <0>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		/* filled by u-boot */
+		reg = <0 0>;
+	};
+
+	soc@e0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		compatible = "fsl,mpc8360-immr", "fsl,immr", "fsl,soc",
+			     "simple-bus";
+		ranges = <0 0xe0000000 0x200000>;
+		reg = <0xe0000000 0x200>;
+		/* filled by u-boot */
+		bus-frequency = <0>;
+
+		wdt@200 {
+			compatible = "mpc83xx_wdt";
+			reg = <0x200 0x100>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <14 8>;
+			interrupt-parent = <&ipic>;
+			dfsrr;
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <16 8>;
+			interrupt-parent = <&ipic>;
+			dfsrr;
+		};
+
+		serial0: serial@4500 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4500 0x100>;
+			interrupts = <9 8>;
+			interrupt-parent = <&ipic>;
+			/* filled by u-boot */
+			clock-frequency = <0>;
+		};
+
+		serial1: serial@4600 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4600 0x100>;
+			interrupts = <10 8>;
+			interrupt-parent = <&ipic>;
+			/* filled by u-boot */
+			clock-frequency = <0>;
+		};
+
+		crypto@30000 {
+			compatible = "fsl,sec2-crypto";
+			reg = <0x30000 0x10000>;
+			interrupts = <11 8>;
+			interrupt-parent = <&ipic>;
+			num-channels = <4>;
+			channel-fifo-len = <24>;
+			exec-units-mask = <0x7e>;
+			/*
+			 * desc mask is for rev1.x, we need runtime fixup
+			 * for >=2.x
+			 */
+			descriptor-types-mask = <0x1010ebf>;
+		};
+
+		ipic: interrupt-controller@700 {
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			compatible = "fsl,pq2pro-pic", "fsl,ipic";
+			interrupt-controller;
+			reg = <0x700 0x100>;
+		};
+
+		qe_pio_b: gpio-controller@1418 {
+			#gpio-cells = <2>;
+			compatible = "fsl,mpc8360-qe-pario-bank",
+				     "fsl,mpc8323-qe-pario-bank";
+			reg = <0x1418 0x18>;
+			gpio-controller;
+		};
+
+		qe_pio_e: gpio-controller@1460 {
+			#gpio-cells = <2>;
+			compatible = "fsl,mpc8360-qe-pario-bank",
+				     "fsl,mpc8323-qe-pario-bank";
+			reg = <0x1460 0x18>;
+			gpio-controller;
+		};
+
+		qe@100000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			device_type = "qe";
+			compatible = "fsl,qe", "simple-bus";
+			ranges = <0 0x100000 0x100000>;
+			reg = <0x100000 0x480>;
+			/* filled by u-boot */
+			clock-frequency = <0>;
+			bus-frequency = <0>;
+			brg-frequency = <0>;
+
+			muram@10000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "fsl,qe-muram", "fsl,cpm-muram";
+				ranges = <0 0x10000 0xc000>;
+
+				data-only@0 {
+					compatible = "fsl,qe-muram-data",
+						     "fsl,cpm-muram-data";
+					reg = <0 0xc000>;
+				};
+			};
+
+			timer@440 {
+				compatible = "fsl,mpc8360-qe-gtm",
+					     "fsl,qe-gtm", "fsl,gtm";
+				reg = <0x440 0x40>;
+				interrupts = <12 13 14 15>;
+				interrupt-parent = <&qeic>;
+				/* filled by u-boot */
+				clock-frequency = <0>;
+			};
+
+			spi@4c0 {
+				cell-index = <0>;
+				compatible = "fsl,spi";
+				reg = <0x4c0 0x40>;
+				interrupts = <2>;
+				interrupt-parent = <&qeic>;
+				mode = "cpu-qe";
+			};
+
+			spi@500 {
+				cell-index = <1>;
+				compatible = "fsl,spi";
+				reg = <0x500 0x40>;
+				interrupts = <1>;
+				interrupt-parent = <&qeic>;
+				mode = "cpu-qe";
+			};
+
+			enet0: ucc@2000 {
+				device_type = "network";
+				compatible = "ucc_geth";
+				cell-index = <1>;
+				reg = <0x2000 0x200>;
+				interrupts = <32>;
+				interrupt-parent = <&qeic>;
+				rx-clock-name = "none";
+				tx-clock-name = "clk9";
+				phy-handle = <&phy2>;
+				phy-connection-type = "rgmii-rxid";
+				/* filled by u-boot */
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			enet1: ucc@3000 {
+				device_type = "network";
+				compatible = "ucc_geth";
+				cell-index = <2>;
+				reg = <0x3000 0x200>;
+				interrupts = <33>;
+				interrupt-parent = <&qeic>;
+				rx-clock-name = "none";
+				tx-clock-name = "clk4";
+				phy-handle = <&phy4>;
+				phy-connection-type = "rgmii-rxid";
+				/* filled by u-boot */
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			enet2: ucc@2600 {
+				device_type = "network";
+				compatible = "ucc_geth";
+				cell-index = <7>;
+				reg = <0x2600 0x200>;
+				interrupts = <42>;
+				interrupt-parent = <&qeic>;
+				rx-clock-name = "clk20";
+				tx-clock-name = "clk19";
+				phy-handle = <&phy1>;
+				phy-connection-type = "mii";
+				/* filled by u-boot */
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			enet3: ucc@3200 {
+				device_type = "network";
+				compatible = "ucc_geth";
+				cell-index = <4>;
+				reg = <0x3200 0x200>;
+				interrupts = <35>;
+				interrupt-parent = <&qeic>;
+				rx-clock-name = "clk8";
+				tx-clock-name = "clk7";
+				phy-handle = <&phy3>;
+				phy-connection-type = "mii";
+				/* filled by u-boot */
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			mdio@2120 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,ucc-mdio";
+				reg = <0x2120 0x18>;
+
+				phy1: ethernet-phy@1 {
+					device_type = "ethernet-phy";
+					compatible = "national,DP83848VV";
+					reg = <1>;
+				};
+
+				phy2: ethernet-phy@2 {
+					device_type = "ethernet-phy";
+					compatible = "broadcom,BCM5481UA2KMLG";
+					reg = <2>;
+				};
+
+				phy3: ethernet-phy@3 {
+					device_type = "ethernet-phy";
+					compatible = "national,DP83848VV";
+					reg = <3>;
+				};
+
+				phy4: ethernet-phy@4 {
+					device_type = "ethernet-phy";
+					compatible = "broadcom,BCM5481UA2KMLG";
+					reg = <4>;
+				};
+			};
+
+			serial2: ucc@2400 {
+				device_type = "serial";
+				compatible = "ucc_uart";
+				reg = <0x2400 0x200>;
+				cell-index = <5>;
+				port-number = <0>;
+				rx-clock-name = "brg7";
+				tx-clock-name = "brg8";
+				interrupts = <40>;
+				interrupt-parent = <&qeic>;
+				soft-uart;
+			};
+
+			serial3: ucc@3400 {
+				device_type = "serial";
+				compatible = "ucc_uart";
+				reg = <0x3400 0x200>;
+				cell-index = <6>;
+				port-number = <1>;
+				rx-clock-name = "brg13";
+				tx-clock-name = "brg14";
+				interrupts = <41>;
+				interrupt-parent = <&qeic>;
+				soft-uart;
+			};
+
+			qeic: interrupt-controller@80 {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				compatible = "fsl,qe-ic";
+				interrupt-controller;
+				reg = <0x80 0x80>;
+				big-endian;
+				interrupts = <32 8 33 8>;
+				interrupt-parent = <&ipic>;
+			};
+		};
+	};
+
+	localbus@e0005000 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8360-localbus", "fsl,pq2pro-localbus",
+			     "simple-bus";
+		reg = <0xe0005000 0xd8>;
+		ranges = <0 0 0xff800000 0x0800000
+			  1 0 0x60000000 0x0001000
+			  2 0 0x70000000 0x4000000>;
+
+		flash@0,0 {
+			compatible = "intel,PC28F640P30T85", "cfi-flash";
+			reg = <0 0 0x800000>;
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		display@2,0 {
+			device_type = "display";
+			compatible = "fujitsu,MB86277", "fujitsu,mint";
+			reg = <2 0 0x4000000>;
+			fujitsu,sh3;
+			little-endian;
+			/* filled by u-boot */
+			address = <0>;
+			depth = <0>;
+			width = <0>;
+			height = <0>;
+			linebytes = <0>;
+			/* linux,opened; - added by uboot */
+		};
+	};
+
+	pci0: pci@e0008500 {
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		device_type = "pci";
+		compatible = "fsl,mpc8360-pci", "fsl,mpc8349-pci";
+		reg = <0xe0008500 0x100>;
+		ranges = <0x02000000 0 0x90000000 0x90000000 0 0x10000000
+			  0x42000000 0 0x80000000 0x80000000 0 0x10000000
+			  0x01000000 0 0xe0300000 0xe0300000 0 0x00100000>;
+		interrupts = <66 8>;
+		interrupt-parent = <&ipic>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = </* miniPCI0 IDSEL 0x14 AD20 */
+				 0xa000 0 0 1 &ipic 18 8
+				 0xa000 0 0 2 &ipic 19 8
+
+				 /* PCI1 IDSEL 0x15 AD21 */
+				 0xa800 0 0 1 &ipic 19 8
+				 0xa800 0 0 2 &ipic 20 8
+				 0xa800 0 0 3 &ipic 21 8
+				 0xa800 0 0 4 &ipic 18 8>;
+		/* filled by u-boot */
+		bus-range = <0 0>;
+		clock-frequency = <0>;
+	};
+};

1,090 lines not on this page · raw message

index 13587e2..9cb9e04 100644
@@ -58,6 +58,17 @@ config MPC836x_MDS
 	help
 	  This option enables support for the MPC836x MDS Processor Board.
 
+config MPC836x_RDK
+	bool "Freescale/Logic MPC836x RDK"
+	select DEFAULT_UIMAGE
+	select QUICC_ENGINE
+	select QE_GPIO
+	select FSL_GTM
+	select FSL_LBC
+	help
+	  This option enables support for the MPC836x RDK Processor Board,
+	  also known as ZOOM PowerQUICC Kit.
+
 config MPC837x_MDS
 	bool "Freescale MPC837x MDS"
 	select DEFAULT_UIMAGE

index 7e6dd3e..1fcda8e 100644
@@ -8,6 +8,7 @@ obj-$(CONFIG_MPC832x_RDB)	+= mpc832x_rdb.o
 obj-$(CONFIG_MPC834x_MDS)	+= mpc834x_mds.o
 obj-$(CONFIG_MPC834x_ITX)	+= mpc834x_itx.o
 obj-$(CONFIG_MPC836x_MDS)	+= mpc836x_mds.o
+obj-$(CONFIG_MPC836x_RDK)	+= mpc836x_rdk.o
 obj-$(CONFIG_MPC832x_MDS)	+= mpc832x_mds.o
 obj-$(CONFIG_MPC837x_MDS)	+= mpc837x_mds.o
 obj-$(CONFIG_SBC834x)		+= sbc834x.o

index 098f456..0b07bc7 100644
@@ -59,6 +59,10 @@ Table of Contents
       p) Freescale Synchronous Serial Interface
       q) USB EHCI controllers
       r) Freescale General-purpose Timers Module
+      s) Freescale QUICC Engine USB Controller
+      t) LEDs on GPIOs
+      u) Freescale MCU with MPC8349E-mITX compatible firmware
+      v) NAND on UPM-driven Freescale Localbus
 
   VII - Marvell Discovery mv64[345]6x System Controller chips
     1) The /system-controller node

@@ -2869,6 +2873,127 @@ platforms are moved over to use the flattened-device-tree model.
     	clock-frequency = <0>;
     };
 
+    s) Freescale QUICC Engine USB Controller
+
+    Required properties:
+      - compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb";
+      - reg : the first two cells should contain gtm registers location and
+        length, the next two two cells should contain PRAM location and
+        length.
+      - interrupts : should contain USB interrupt.
+      - interrupt-parent : interrupt source phandle.
+      - fsl,fullspeed-clock : specifies the full speed USB clock source in
+        "clk<num>" or "brg<num>" format.
+      - fsl,lowspeed-clock : specifies the low speed USB clock source in
+        "clk<num>" or "brg<num>" format.
+      - fsl,usb-mode : should be "host".
+      - linux,hub-power-budget : optional, USB power budget for the root hub
+        in mA.
+      - gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP,
+        USBRN, SPEED (optional), and POWER (optional).
+
+    Example:
+
+	usb@6c0 {
+		compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb";
+		reg = <0x6c0 0x40 0x8b00 0x100>;
+		interrupts = <11>;
+		interrupt-parent = <&qeic>;
+		fsl,fullspeed-clock = "clk21";
+		fsl,usb-mode = "host";
+		gpios = <&qe_pio_b  2 0 /* USBOE */
+			 &qe_pio_b  3 0 /* USBTP */
+			 &qe_pio_b  8 0 /* USBTN */
+			 &qe_pio_b  9 0 /* USBRP */
+			 &qe_pio_b 11 0 /* USBRN */
+			 &qe_pio_e 20 0 /* SPEED */
+			 &qe_pio_e 21 0 /* POWER */>;
+	};
+
+    t) LEDs on GPIOs
+
+    Required properties:
+      - compatible : should be "linux,gpio-led".
+      - linux,name : LED name.
+      - linux,active-low : property should be present if LED wired as
+        active-low.
+      - linux,default-trigger : Linux default trigger for this LED.
+      - linux,brightness : default brightness.
+      - gpios : should specify LED GPIO.
+
+    Example:
+
+	led@0 {
+		compatible = "linux,gpio-led";
+		linux,name = "pwr";
+		linux,brightness = <1>;
+		linux,active-low;
+		gpios = <&mcu_pio 0>;
+	};
+
+	led@1 {
+	        compatible = "linux,gpio-led";
+	        linux,name = "hdd";
+	        linux,default-trigger = "ide-disk";
+		linux,active-low;
+		gpios = <&mcu_pio 1>;
+	};
+
+    u) Freescale MCU with MPC8349E-mITX compatible firmware
+
+    Required properties:
+      - compatible : "fsl,<mcu-chip>-<board>", "fsl,mcu-mpc8349emitx";
+      - reg : should specify I2C address (0x0a).
+      - #address-cells : should be 0.
+      - #size-cells : should be 0.
+      - #gpio-cells : should be 2.
+      - gpio-controller : should be present;
+
+    Example:
+
+	mcu_pio: mcu@0a {
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#gpio-cells = <2>;
+		compatible = "fsl,mc9s08qg8-mpc8349emitx",
+			     "fsl,mcu-mpc8349emitx";
+		reg = <0x0a>;
+		gpio-controller;
+	};
+
+    v) Freescale Localbus UPM programmed to work with NAND flash
+
+      Required properties:
+      - #address-cells : should be 0;
+      - #size-cells : should be 0;
+      - compatible : "fsl,upm-nand".
+      - reg : should specify localbus chip select and size used for the chip.
+      - fsl,upm-addr-offset : UPM pattern offset for the address latch.
+      - fsl,upm-cmd-offset : UPM pattern offset for the command latch.
+      - gpios : may specify optional GPIO connected to the Ready-Not-Busy pin.
+
+      Example:
+
+	upm@1,0 {
+		#address-cells = <0>;
+		#size-cells = <0>;
+		compatible = "fsl,upm-nand";
+		reg = <1 0 1>;
+		fsl,upm-addr-offset = <16>;
+		fsl,upm-cmd-offset = <8>;
+		gpios = <&qe_pio_e 18 0>;
+
+		flash {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "stmicro,NAND512W3A2BN6E";
+
+			partition@0 {
+				...
+			};
+		};
+	};
+
 VII - Marvell Discovery mv64[345]6x System Controller chips
 ===========================================================