siimage: add sil_* I/O ops
PATCH 2/3 siimage: add sil_* I/O ops
Add sil_iowrite{8,16,32}() and sil_ioread{8,16}() helpers, then use them to merge code accessing configuration registers through PCI and MMIO together.
[ because of this SATA initialization bits from setup_mmio_siimage() are
moved to init_chipset_siimage() ]
This also cuts code size a bit:
text data bss dec hex filename
4437 164 0 4601 11f9 drivers/ide/pci/siimage.o.before 3979 164 0 4143 102f drivers/ide/pci/siimage.o.after
While at it:
* Use I/O ops directly instead of using ->IN{B,W} and ->OUT{B,W}.
* Fixup CodingStyle in setup_mmio_siimage().
* Rename 'tmpbyte' variable to 'tmp' in init_chipset_siimage().
There should be no functional changes caused by this patch.
--- drivers/ide/pci/siimage.c | 303 +++++++++++++++++++++------------------------- 1 file changed, 142 insertions(+), 161 deletions(-)
drivers/ide/pci/siimage.c +142 -161
@@ -2,7 +2,7 @@* Copyright (C) 2001-2002 Andre Hedrick <[email protected]> * Copyright (C) 2003 Red Hat <[email protected]> * Copyright (C) 2007 MontaVista Software, Inc. -* Copyright (C) 2007 Bartlomiej Zolnierkiewicz +* Copyright (C) 2007-2008 Bartlomiej Zolnierkiewicz * * May be copied or modified under the terms of the GNU General Public License *
@@ -124,6 +124,54 @@ static inline unsigned long siimage_seldreturn base; } +static u8 sil_ioread8 (struct pci_dev *dev,unsigned long addr) +{ +u8 tmp =0 ; + +if (pci_get_drvdata (dev)) + tmp =readb ((void __iomem *)addr); +else +pci_read_config_byte (dev, addr, &tmp); + +return tmp; +} + +static u16 sil_ioread16 (struct pci_dev *dev,unsigned long addr) +{ +u16 tmp =0 ; + +if (pci_get_drvdata (dev)) + tmp =readw ((void __iomem *)addr); +else +pci_read_config_word (dev, addr, &tmp); + +return tmp; +} + +static void sil_iowrite8 (struct pci_dev *dev,u8 val,unsigned long addr) +{ +if (pci_get_drvdata (dev)) +writeb (val, (void __iomem *)addr); +else +pci_write_config_byte (dev, addr, val); +} + +static void sil_iowrite16 (struct pci_dev *dev,u16 val,unsigned long addr) +{ +if (pci_get_drvdata (dev)) +writew (val, (void __iomem *)addr); +else +pci_write_config_word (dev, addr, val); +} + +static void sil_iowrite32 (struct pci_dev *dev,u32 val,unsigned long addr) +{ +if (pci_get_drvdata (dev)) +writel (val, (void __iomem *)addr); +else +pci_write_config_dword (dev, addr, val); +} +/** * sil_udma_filter - compute UDMA mask * @drive: IDE device
@@ -139,12 +187,9 @@ static u8 sil_pata_udma_filter(ide_driveide_hwif_t *hwif = drive->hwif;struct pci_dev *dev =to_pci_dev (hwif->dev);unsigned long base = (unsigned long ) hwif->hwif_data; -u8 mask =0 , scsc =0 ; +u8 mask =0 , scsc; -if (hwif->mmio) - scsc = hwif->INB (base +0x4A ); -else -pci_read_config_byte (dev,0x8A , &scsc); + scsc =sil_ioread8 (dev, base + (hwif->mmio ?0x4A :0x8A ));if ((scsc &0x30 ) ==0x10 )/* 133 */ mask =ATA_UDMA6 ;
@@ -179,6 +224,7 @@ static void sil_set_pio_mode(ide_drive_tconst u16 data_speed[] = {0x328a ,0x2283 ,0x1104 ,0x10c3 ,0x10c1 };ide_hwif_t *hwif =HWIF (drive); +struct pci_dev *dev =to_pci_dev (hwif->dev);ide_drive_t *pair =ide_get_paired_drive (drive);u32 speedt =0 ;u16 speedp =0 ;
@@ -203,36 +249,20 @@ static void sil_set_pio_mode(ide_drive_t speedp = data_speed[pio]; speedt = tf_speed[tf_pio]; -if (hwif->mmio) { - hwif->OUTW (speedp, addr); - hwif->OUTW (speedt, tfaddr); -/* Now set up IORDY */ -if (pio >2 ) - hwif->OUTW (hwif->INW (tfaddr-2 )|0x200 , tfaddr-2 ); -else - hwif->OUTW (hwif->INW (tfaddr-2 )&~0x200 , tfaddr-2 ); - - mode = hwif->INB (base + addr_mask); - mode &= ~(unit ?0x30 :0x03 ); - mode |= (unit ?0x10 :0x01 ); - hwif->OUTB (mode, base + addr_mask); - }else { -struct pci_dev *dev =to_pci_dev (hwif->dev); +sil_iowrite16 (dev, speedp, addr); +sil_iowrite16 (dev, speedt, tfaddr); -pci_write_config_word (dev, addr, speedp); -pci_write_config_word (dev, tfaddr, speedt); -pci_read_config_word (dev, tfaddr -2 , &speedp); - speedp &= ~0x200 ; -/* Set IORDY for mode 3 or 4 */ -if (pio >2 ) - speedp |=0x200 ; -pci_write_config_word (dev, tfaddr -2 , speedp); - -pci_read_config_byte (dev, addr_mask, &mode); - mode &= ~(unit ?0x30 :0x03 ); - mode |= (unit ?0x10 :0x01 ); -pci_write_config_byte (dev, addr_mask, mode); - } +/* now set up IORDY */ + speedp =sil_ioread16 (dev, tfaddr -2 ); + speedp &= ~0x200 ; +if (pio >2 ) + speedp |=0x200 ; +sil_iowrite16 (dev, speedp, tfaddr -2 ); + + mode =sil_ioread8 (dev, base + addr_mask); + mode &= ~(unit ?0x30 :0x03 ); + mode |= (unit ?0x10 :0x01 ); +sil_iowrite8 (dev, mode, base + addr_mask); }/**
@@ -261,17 +291,10 @@ static void sil_set_dma_mode(ide_drive_tunsigned long ma =siimage_seldev (drive,0x08 );unsigned long ua =siimage_seldev (drive,0x0C ); -if (hwif->mmio) { - scsc = hwif->INB (base +0x4A ); - mode = hwif->INB (base + addr_mask); - multi = hwif->INW (ma); - ultra = hwif->INW (ua); - }else { -pci_read_config_byte (dev,0x8A , &scsc); -pci_read_config_byte (dev, addr_mask, &mode); -pci_read_config_word (dev, ma, &multi); -pci_read_config_word (dev, ua, &ultra); - } + scsc =sil_ioread8 (dev, base + (hwif->mmio ?0x4A :0x8A )); + mode =sil_ioread8 (dev, base + addr_mask); + multi =sil_ioread16 (dev, ma); + ultra =sil_ioread16 (dev, ua); mode &= ~((unit) ?0x30 :0x03 ); ultra &= ~0x3F ;
@@ -289,15 +312,9 @@ static void sil_set_dma_mode(ide_drive_t mode |= (unit ?0x20 :0x02 ); } -if (hwif->mmio) { - hwif->OUTB (mode, base + addr_mask); - hwif->OUTW (multi, ma); - hwif->OUTW (ultra, ua); - }else { -pci_write_config_byte (dev, addr_mask, mode); -pci_write_config_word (dev, ma, multi); -pci_write_config_word (dev, ua, ultra); - } +sil_iowrite8 (dev, mode, base + addr_mask); +sil_iowrite16 (dev, multi, ma); +sil_iowrite16 (dev, ultra, ua); }/* returns 1 if dma irq issued, 0 otherwise */
@@ -460,26 +477,21 @@ static unsigned int setup_mmio_siimage ( {resource_size_t bar5 =pci_resource_start (dev,5 );unsigned long barsize =pci_resource_len (dev,5 ); -u8 tmpbyte =0 ;void __iomem *ioaddr; -u32 tmp, irq_mask;/* * Drop back to PIO if we can't map the mmio. Some * systems seem to get terminally confused in the PCI * spaces. */ - -if (!request_mem_region (bar5, barsize, name)) - { +if (!request_mem_region (bar5, barsize, name)) {printk (KERN_WARNING "siimage: IDE controller MMIO ports not available.\n" );return 0 ; } - + ioaddr =ioremap (bar5, barsize); -if (ioaddr ==NULL ) - { +if (ioaddr ==NULL ) {release_mem_region (bar5, barsize);return 0 ; }
@@ -487,62 +499,6 @@ static unsigned int setup_mmio_siimage (pci_set_master (dev);pci_set_drvdata (dev, (void *) ioaddr); -if (pdev_is_sata (dev)) { -/* make sure IDE0/1 interrupts are not masked */ - irq_mask = (1 <<22 ) | (1 <<23 ); - tmp =readl (ioaddr +0x48 ); -if (tmp & irq_mask) { - tmp &= ~irq_mask; -writel (tmp, ioaddr +0x48 ); -readl (ioaddr +0x48 );/* flush */ - } -writel (0 , ioaddr +0x148 ); -writel (0 , ioaddr +0x1C8 ); - } - -writeb (0 , ioaddr +0xB4 ); -writeb (0 , ioaddr +0xF4 ); - tmpbyte =readb (ioaddr +0x4A ); - -switch (tmpbyte &0x30 ) { -case 0x00 : -/* In 100 MHz clocking, try and switch to 133 */ -writeb (tmpbyte|0x10 , ioaddr +0x4A ); -break ; -case 0x10 : -/* On 133Mhz clocking */ -break ; -case 0x20 : -/* On PCIx2 clocking */ -break ; -case 0x30 : -/* Clocking is disabled */ -/* 133 clock attempt to force it on */ -writeb (tmpbyte & ~0x20 , ioaddr +0x4A ); -break ; - } - - tmpbyte =readb (ioaddr +0x4A ); - -writeb (0x72 , ioaddr +0xA1 ); -writew (0x328A , ioaddr +0xA2 ); -writel (0x62DD62DD , ioaddr +0xA4 ); -writel (0x43924392 , ioaddr +0xA8 ); -writel (0x40094009 , ioaddr +0xAC ); -writeb (0x72 , ioaddr +0xE1 ); -writew (0x328A , ioaddr +0xE2 ); -writel (0x62DD62DD , ioaddr +0xE4 ); -writel (0x43924392 , ioaddr +0xE8 ); -writel (0x40094009 , ioaddr +0xEC ); - -if (pdev_is_sata (dev)) { -writel (0xFFFF0000 , ioaddr +0x108 ); -writel (0xFFFF0000 , ioaddr +0x188 ); -writel (0x00680000 , ioaddr +0x148 ); -writel (0x00680000 , ioaddr +0x1C8 ); - } - -proc_reports_siimage (dev, (tmpbyte>>4 ), name);return 1 ; }
@@ -557,50 +513,80 @@ static unsigned int setup_mmio_siimage (static unsigned int __devinit init_chipset_siimage (struct pci_dev *dev,const char *name) { -u8 rev = dev->revision, tmpbyte =0 ,BA5_EN =0 ; +unsigned long base, scsc_addr; +void __iomem *ioaddr =NULL ; +u8 rev = dev->revision, tmp =0 ,BA5_EN =0 ;pci_write_config_byte (dev,PCI_CACHE_LINE_SIZE , rev ?1 :255 );pci_read_config_byte (dev,0x8A , &BA5_EN ); -if ((BA5_EN &0x01 ) || (pci_resource_start (dev,5 ))) { -if (setup_mmio_siimage (dev, name)) { -return 0 ; + +if ((BA5_EN &0x01 ) ||pci_resource_start (dev,5 )) { +if (setup_mmio_siimage (dev, name)) + ioaddr =pci_get_drvdata (dev); + } + + base = (unsigned long )ioaddr; + +if (ioaddr &&pdev_is_sata (dev)) { +u32 tmp32, irq_mask; + +/* make sure IDE0/1 interrupts are not masked */ + irq_mask = (1 <<22 ) | (1 <<23 ); + tmp32 =readl (ioaddr +0x48 ); +if (tmp32 & irq_mask) { + tmp32 &= ~irq_mask; +writel (tmp32, ioaddr +0x48 ); +readl (ioaddr +0x48 );/* flush */ } +writel (0 , ioaddr +0x148 ); +writel (0 , ioaddr +0x1C8 ); + } + +sil_iowrite8 (dev,0 , base ? (base +0xB4 ) :0x80 ); +sil_iowrite8 (dev,0 , base ? (base +0xF4 ) :0x84 ); + + scsc_addr = base ? (base +0x4A ) :0x8A ; + tmp =sil_ioread8 (dev, scsc_addr); + +switch (tmp &0x30 ) { +case 0x00 : +/* On 100MHz clocking, try and switch to 133MHz */ +sil_iowrite8 (dev, tmp |0x10 , scsc_addr); +break ; +case 0x30 : +/* Clocking is disabled, attempt to force 133MHz clocking. */ +sil_iowrite8 (dev, tmp & ~0x20 , scsc_addr); +case 0x10 : +/* On 133Mhz clocking. */ +break ; +case 0x20 : +/* On PCIx2 clocking. */ +break ; + } + + tmp =sil_ioread8 (dev, scsc_addr); + +sil_iowrite8 (dev,0x72 , base +0xA1 ); +sil_iowrite16 (dev,0x328A , base +0xA2 ); +sil_iowrite32 (dev,0x62DD62DD , base +0xA4 ); +sil_iowrite32 (dev,0x43924392 , base +0xA8 ); +sil_iowrite32 (dev,0x40094009 , base +0xAC ); +sil_iowrite8 (dev,0x72 , base ? (base +0xE1 ) :0xB1 ); +sil_iowrite16 (dev,0x328A , base ? (base +0xE2 ) :0xB2 ); +sil_iowrite32 (dev,0x62DD62DD , base ? (base +0xE4 ) :0xB4 ); +sil_iowrite32 (dev,0x43924392 , base ? (base +0xE8 ) :0xB8 ); +sil_iowrite32 (dev,0x40094009 , base ? (base +0xEC ) :0xBC ); + +if (base &&pdev_is_sata (dev)) { +writel (0xFFFF0000 , ioaddr +0x108 ); +writel (0xFFFF0000 , ioaddr +0x188 ); +writel (0x00680000 , ioaddr +0x148 ); +writel (0x00680000 , ioaddr +0x1C8 ); } -pci_write_config_byte (dev,0x80 ,0x00 ); -pci_write_config_byte (dev,0x84 ,0x00 ); -pci_read_config_byte (dev,0x8A , &tmpbyte); -switch (tmpbyte &0x30 ) { -case 0x00 : -/* 133 clock attempt to force it on */ -pci_write_config_byte (dev,0x8A , tmpbyte|0x10 ); -case 0x30 : -/* if clocking is disabled */ -/* 133 clock attempt to force it on */ -pci_write_config_byte (dev,0x8A , tmpbyte & ~0x20 ); -case 0x10 : -/* 133 already */ -break ; -case 0x20 : -/* BIOS set PCI x2 clocking */ -break ; - } - -pci_read_config_byte (dev,0x8A , &tmpbyte); - -pci_write_config_byte (dev,0xA1 ,0x72 ); -pci_write_config_word (dev,0xA2 ,0x328A ); -pci_write_config_dword (dev,0xA4 ,0x62DD62DD ); -pci_write_config_dword (dev,0xA8 ,0x43924392 ); -pci_write_config_dword (dev,0xAC ,0x40094009 ); -pci_write_config_byte (dev,0xB1 ,0x72 ); -pci_write_config_word (dev,0xB2 ,0x328A ); -pci_write_config_dword (dev,0xB4 ,0x62DD62DD ); -pci_write_config_dword (dev,0xB8 ,0x43924392 ); -pci_write_config_dword (dev,0xBC ,0x40094009 ); +proc_reports_siimage (dev, tmp >>4 , name); -proc_reports_siimage (dev, (tmpbyte>>4 ), name);return 0 ; }
@@ -752,12 +738,7 @@ static u8 __devinit sil_cable_detect(ide {struct pci_dev *dev =to_pci_dev (hwif->dev);unsigned long addr =siimage_selreg (hwif,0 ); -u8 ata66 =0 ; - -if (pci_get_drvdata (dev) ==NULL ) -pci_read_config_byte (dev, addr, &ata66); -else - ata66 = hwif->INB (addr); +u8 ata66 =sil_ioread8 (dev, addr);return (ata66 &0x01 ) ?ATA_CBL_PATA80 :ATA_CBL_PATA40 ; }
Quoted 2 lines · Bartlomiej Zolnierkiewicz
Add sil_iowrite{8,16,32}() and sil_ioread{8,16}() helpers, then use them to merge code accessing configuration registers through PCI and MMIO together.
Sigh, my coding style cleanup patch heavily clashed with this one, so I had
to recast it...
Quoted 8 lines
[ because of this SATA initialization bits from
setup_mmio_siimage()are
moved toinit_chipset_siimage()]This also cuts code size a bit:
text data bss dec hex filename 4437 164 0 4601 11f9 drivers/ide/pci/siimage.o.before 3979 164 0 4143 102f drivers/ide/pci/siimage.o.after
Good work. :-)
Quoted 11 lines
While at it:
* Use I/O ops directly instead of using ->IN{B,W} and ->OUT{B,W}.
* Fixup CodingStyle in
setup_mmio_siimage().* Rename 'tmpbyte' variable to 'tmp' in
init_chipset_siimage().There should be no functional changes caused by this patch.
Signed-off-by Bartlomiej Zolnierkiewicz <[email protected]>
Quoted 55 lines
Index:
b/drivers/ide/pci/siimage.c
===================================================================drivers/ide/pci/siimage.c +39
-1@@ -2,7 +2,7 @@* Copyright (C) 2001-2002 Andre Hedrick <[email protected]> * Copyright (C) 2003 Red Hat <[email protected]> * Copyright (C) 2007 MontaVista Software, Inc. -* Copyright (C) 2007 Bartlomiej Zolnierkiewicz +* Copyright (C) 2007-2008 Bartlomiej Zolnierkiewicz * * May be copied or modified under the terms of the GNU General Public License * @@ -124,6 +124,54 @@ static inline unsigned long siimage_seldreturn base; } +static u8 sil_ioread8 (struct pci_dev *dev,unsigned long addr) +{ +u8 tmp =0 ; + +if (pci_get_drvdata (dev)) + tmp =readb ((void __iomem *)addr); +else +pci_read_config_byte (dev, addr, &tmp); + +return tmp; +} + +static u16 sil_ioread16 (struct pci_dev *dev,unsigned long addr) +{ +u16 tmp =0 ; + +if (pci_get_drvdata (dev)) + tmp =readw ((void __iomem *)addr); +else +pci_read_config_word (dev, addr, &tmp); + +return tmp; +} + +static void sil_iowrite8 (struct pci_dev *dev,u8 val,unsigned long addr) +{ +if (pci_get_drvdata (dev)) +writeb (val, (void __iomem *)addr); +else +pci_write_config_byte (dev, addr, val); +} + +static void sil_iowrite16 (struct pci_dev *dev,u16 val,unsigned long addr) +{ +if (pci_get_drvdata (dev)) +writew (val, (void __iomem *)addr); +else +pci_write_config_word (dev, addr, val);
drivers/ide/pci/siimage.c static inline unsigned long siimage_seld · line 174
Quoted 10 lines
drivers/ide/pci/siimage.c +10
-0+} + +static void sil_iowrite32 (struct pci_dev *dev,u32 val,unsigned long addr) +{ +if (pci_get_drvdata (dev)) +writel (val, (void __iomem *)addr); +else +pci_write_config_dword (dev, addr, val); +} +
I think this could be further imporoved -- since we have to callpci_get_drvdata() in the accessors anyway, we could have used it to get the MMIO base right there, and thus be freed from the necessity to add it to the MMIO offset in the callers and also most probably from having it copied to hwif->hwif_data.
Quoted 1 line
drivers/ide/pci/siimage.c +0
-0@@ -203,36 +249,20 @@ static void sil_set_pio_mode(ide_drive_t
[...]
drivers/ide/pci/siimage.c static void sil_set_pio_mode(ide_drive_t · line 264
Quoted 1 line
drivers/ide/pci/siimage.c +1
-0+ mode |= (unit ?0x10 :0x01 );
Useless parens -- I'm getting rid of them in my patch anyway...
Quoted 1 line
drivers/ide/pci/siimage.c +0
-0@@ -557,50 +513,80 @@ static unsigned int setup_mmio_siimage (
[...]
drivers/ide/pci/siimage.c static unsigned int setup_mmio_siimage ( · line 580
Quoted 11 lines
drivers/ide/pci/siimage.c +11
-0+sil_iowrite8 (dev,0x72 , base +0xA1 ); +sil_iowrite16 (dev,0x328A , base +0xA2 ); +sil_iowrite32 (dev,0x62DD62DD , base +0xA4 ); +sil_iowrite32 (dev,0x43924392 , base +0xA8 ); +sil_iowrite32 (dev,0x40094009 , base +0xAC ); +sil_iowrite8 (dev,0x72 , base ? (base +0xE1 ) :0xB1 ); +sil_iowrite16 (dev,0x328A , base ? (base +0xE2 ) :0xB2 ); +sil_iowrite32 (dev,0x62DD62DD , base ? (base +0xE4 ) :0xB4 ); +sil_iowrite32 (dev,0x43924392 , base ? (base +0xE8 ) :0xB8 ); +sil_iowrite32 (dev,0x40094009 , base ? (base +0xEC ) :0xBC ); +
Sigh, I was going to send a patch getting rid of these writes altogether
last year -- there should be no point in setting PIO/DMA/UDMA timings here. Maybe I'll submit it...
MBR, Sergei
On Saturday 19 April 2008, Sergei Shtylyov wrote:
[...]
Quoted 50 lines
Quoted 50 lines
drivers/ide/pci/siimage.c +46
-0@@ -124,6 +124,54 @@ static inline unsigned long siimage_seldreturn base; } +static u8 sil_ioread8 (struct pci_dev *dev,unsigned long addr) +{ +u8 tmp =0 ; + +if (pci_get_drvdata (dev)) + tmp =readb ((void __iomem *)addr); +else +pci_read_config_byte (dev, addr, &tmp); + +return tmp; +} + +static u16 sil_ioread16 (struct pci_dev *dev,unsigned long addr) +{ +u16 tmp =0 ; + +if (pci_get_drvdata (dev)) + tmp =readw ((void __iomem *)addr); +else +pci_read_config_word (dev, addr, &tmp); + +return tmp; +} + +static void sil_iowrite8 (struct pci_dev *dev,u8 val,unsigned long addr) +{ +if (pci_get_drvdata (dev)) +writeb (val, (void __iomem *)addr); +else +pci_write_config_byte (dev, addr, val); +} + +static void sil_iowrite16 (struct pci_dev *dev,u16 val,unsigned long addr) +{ +if (pci_get_drvdata (dev)) +writew (val, (void __iomem *)addr); +else +pci_write_config_word (dev, addr, val); +} + +static void sil_iowrite32 (struct pci_dev *dev,u32 val,unsigned long addr) +{ +if (pci_get_drvdata (dev)) +writel (val, (void __iomem *)addr); +else +pci_write_config_dword (dev, addr, val);
Quoted 8 lines
Review static inline unsigned long siimage_seld · line 174
Quoted 2 lines
(quoted diff) +2
-0+} +I think this could be further imporoved -- since we have to call
pci_get_drvdata()in the accessors anyway, we could have used it to get the MMIO base right there, and thus be freed from the necessity to add it to the MMIO offset in the callers and also most probably from having it copied tohwif->hwif_data.
[...]
Or maybe we can remove sil_io* and always use PCI access (on the second look none of sil_io* users seems to be performance critical)...
Quoted 16 lines
Quoted 1 line
(quoted diff) +0
-0@@ -557,50 +513,80 @@ static unsigned int setup_mmio_siimage ([...]
drivers/ide/pci/siimage.c static unsigned int setup_mmio_siimage ( · line 580
Quoted 11 lines
drivers/ide/pci/siimage.c +11
-0+sil_iowrite8 (dev,0x72 , base +0xA1 ); +sil_iowrite16 (dev,0x328A , base +0xA2 ); +sil_iowrite32 (dev,0x62DD62DD , base +0xA4 ); +sil_iowrite32 (dev,0x43924392 , base +0xA8 ); +sil_iowrite32 (dev,0x40094009 , base +0xAC ); +sil_iowrite8 (dev,0x72 , base ? (base +0xE1 ) :0xB1 ); +sil_iowrite16 (dev,0x328A , base ? (base +0xE2 ) :0xB2 ); +sil_iowrite32 (dev,0x62DD62DD , base ? (base +0xE4 ) :0xB4 ); +sil_iowrite32 (dev,0x43924392 , base ? (base +0xE8 ) :0xB8 ); +sil_iowrite32 (dev,0x40094009 , base ? (base +0xEC ) :0xBC ); +Sigh, I was going to send a patch getting rid of these writes altogether
last year -- there should be no point in setting PIO/DMA/UDMA timings here.
Heh, I know the feeling damn too well - I still have few low-prio patches back from *2004* which need to be refreshed and pushed out...
Quoted 1 line
Maybe I'll submit it...
Just do it. ;)
Thanks,
Bart
BTW. siimage crashes on boot here due to dma_ops being mostly full of NULL... This is with current linus.
Ben.