Problems with -git14
Hi...
I have a couple problems with latest git (-14):
- It only recognises 2 processors out of 4 (dual Xeon HT)
- It oopses on the swapper process just on boot...
Difference in dmesg is below. If full correct dmesg or config is needed, please ask for them. The kernel was built copying old 2.6.25 config to .config && make oldconfig. I filled the missing gaps like PAT and others...
dm-git14.txt renamed from dm.txt +135 -87
@@ -1,4 +1,4 @@ -Linux version 2.6.25-jam01 (root@werewolf) (gcc version 4.2.3 (4.2.3-6mnb1)) #6 SMP PREEMPT Mon Apr 21 20:28:14 CEST 2008 +Linux version 2.6.25-jam02 (root@werewolf) (gcc version 4.2.3 (4.2.3-6mnb1)) #1 SMP PREEMPT Wed Apr 30 00:49:19 CEST 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f400 (usable) BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
@@ -8,11 +8,9 @@ BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data) BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) +x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 1150MB HIGHMEM available. 896MB LOWMEM available. -Scan SMP from c0000000 for 1024 bytes. -Scan SMP from c009fc00 for 1024 bytes. -Scan SMP from c00f0000 for 65536 bytes. found SMP MP-table at [c00f57c0] 000f57c0 Entering add_active_range(0, 0, 524000) 0 entries of 256 used Zone PFN ranges:
@@ -42,13 +40,13 @@ ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) -Processor #0 15:2 APIC version 20 +BIOS bug, APIC version is 0 for CPU#0! fixing up to 0x10. (tell your hw vendor) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled) -Processor #6 15:2 APIC version 20 -ACPI: LAPIC (acpi_id[0x02] lapic_id[0x07] enabled) -Processor #7 15:2 APIC version 20 -ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled) -Processor #1 15:2 APIC version 20 +BIOS bug, APIC version is 0 for CPU#0! fixing up to 0x10. (tell your hw vendor) +ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) +BIOS bug, APIC version is 0 for CPU#0! fixing up to 0x10. (tell your hw vendor) +ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled) +BIOS bug, APIC version is 0 for CPU#0! fixing up to 0x10. (tell your hw vendor) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
@@ -63,6 +61,8 @@ Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 80000000 (gap: 7ff00000:7ed00000) +PERCPU: Allocating 39024 bytes of per cpu data +NR_CPUS: 4, nr_cpu_ids: 4 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519907 Kernel command line: video=vesafb:mtrr,ywrap vga=773 ro root=/dev/sda1 mapped APIC to ffffb000 (fee00000)
@@ -70,72 +70,57 @@ Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 -CPU 0 irqstacks, hard=c0458000 soft=c0454000 +CPU 0 irqstacks, hard=c043b000 soft=c0437000 PID hash table entries: 4096 (order: 12, 16384 bytes) -Detected 2405.510 MHz processor. +Detected 2405.615 MHz processor. Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) -Memory: 2073904k/2096000k available (2298k kernel code, 21036k reserved, 812k data, 268k init, 1178496k highmem) +Memory: 2074016k/2096000k available (2218k kernel code, 20936k reserved, 812k data, 232k init, 1178496k highmem) virtual kernel memory layout: fixmap : 0xfff81000 - 0xfffff000 ( 504 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) - .init : 0xc040e000 - 0xc0451000 ( 268 kB) - .data : 0xc033e8de - 0xc0409a48 ( 812 kB) - .text : 0xc0100000 - 0xc033e8de (2298 kB) + .init : 0xc03fa000 - 0xc0434000 ( 232 kB) + .data : 0xc032aa15 - 0xc03f5af0 ( 812 kB) + .text : 0xc0100000 - 0xc032aa15 (2218 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. CPA: page pool initialized 1 of 1 pages preallocated -SLUB: Genslabs=12, HWalign=128, Order=0-1, MinObjects=4, CPUs=4, Nodes=1 -Calibrating delay using timer specific routine.. 4813.42 BogoMIPS (lpj=2406712) +SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 +Calibrating delay using timer specific routine.. 4813.29 BogoMIPS (lpj=2406649) Mount-cache hash table entries: 512 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. -Freeing SMP alternatives: 11k freed +Freeing SMP alternatives: 10k freed ACPI: Core revision 20070126 +ENABLING IO-APIC IRQs +..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Xeon(TM) CPU 2.40GHz stepping 09 +CPU 1 irqstacks, hard=c043c000 soft=c0438000 Booting processor 1/1 ip 2000 -CPU 1 irqstacks, hard=c0459000 soft=c0455000 Initializing CPU#1 -Calibrating delay using timer specific routine.. 4810.24 BogoMIPS (lpj=2405121) +Calibrating delay using timer specific routine.. 4810.28 BogoMIPS (lpj=2405142) CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 +x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: Intel(R) Xeon(TM) CPU 2.40GHz stepping 09 -Booting processor 2/6 ip 2000 -CPU 2 irqstacks, hard=c045a000 soft=c0456000 -Initializing CPU#2 -Calibrating delay using timer specific routine.. 4810.31 BogoMIPS (lpj=2405158) -CPU: Trace cache: 12K uops, L1 D cache: 8K -CPU: L2 cache: 512K -CPU: Physical Processor ID: 3 -CPU2: Intel(R) Xeon(TM) CPU 2.40GHz stepping 09 -Booting processor 3/7 ip 2000 -CPU 3 irqstacks, hard=c045b000 soft=c0457000 -Initializing CPU#3 -Calibrating delay using timer specific routine.. 4810.31 BogoMIPS (lpj=2405158) -CPU: Trace cache: 12K uops, L1 D cache: 8K -CPU: L2 cache: 512K -CPU: Physical Processor ID: 3 -CPU3: Intel(R) Xeon(TM) CPU 2.40GHz stepping 09 -Total of 4 processors activated (19244.29 BogoMIPS). -ENABLING IO-APIC IRQs -..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: passed. -checking TSC synchronization [CPU#0 -> CPU#2]: passed. -checking TSC synchronization [CPU#0 -> CPU#3]: passed. -Brought up 4 CPUs -net_namespace: 160 bytes +native_cpu_up: bad cpu 2 +native_cpu_up: bad cpu 3 +Brought up 2 CPUs +Total of 2 processors activated (9623.58 BogoMIPS). +net_namespace: 200 bytes NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb7f0, last bus=3 -PCI: Using configuration type 1 +PCI: Using configuration type 1 for base access Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled
@@ -167,7 +152,6 @@ usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing -PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report hpet clockevent registered hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz
@@ -213,7 +197,9 @@ TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered +NET: Registered protocol family 1 highmem bounce pool size: 64 pages +msgmni has been set to 1750 for ipc namespace c03dadc0 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered
@@ -231,10 +217,8 @@ Non-volatile memory driver v1.2 intel_rng: FWH not detected ACPI: PCI Interrupt 0000:03:0a.0[A] -> GSI 22 (level, low) -> IRQ 22 -Switched to high resolution mode on CPU 2 -Switched to high resolution mode on CPU 3 -Switched to high resolution mode on CPU 0 Switched to high resolution mode on CPU 1 +Switched to high resolution mode on CPU 0 scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 <Adaptec 29320 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
@@ -243,19 +227,81 @@ <Adaptec 29320 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs scsi 1:0:0:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3 - target1:0:0: asynchronous +------------[ cut here ]------------ +WARNING: at include/linux/blkdev.h:427 blk_queue_init_tags+0x110/0x11f() +Modules linked in: +Pid: 1, comm: swapper Not tainted 2.6.25-jam02 #1 + [<c011e618>] warn_on_slowpath+0x4d/0x66 + [<c0133078>] __atomic_notifier_call_chain+0x27/0x48 + [<c01330b0>] atomic_notifier_call_chain+0x17/0x1b + [<c024367e>] notify_update+0x1f/0x23 + [<c02438c7>] vt_console_print+0x1dd/0x2ab + [<c02436ea>] vt_console_print+0x0/0x2ab + [<c0132c3e>] up+0x9/0x2b + [<c01eca3c>] init_tag_map+0x4e/0x95 + [<c01ecb61>] __blk_queue_init_tags+0x27/0x4e + [<c01ecc98>] blk_queue_init_tags+0x110/0x11f + [<c027e9fb>] ahd_platform_set_tags+0x177/0x1a7 + [<c027f0a7>] ahd_linux_slave_configure+0xcd/0x131 + [<c02576fe>] scsi_probe_and_add_lun+0x706/0x964 + [<c0257b27>] __scsi_scan_target+0xd9/0x5d9 + [<c019c3b3>] sysfs_ilookup_test+0x0/0xd + [<c019ce3a>] sysfs_addrm_finish+0x14/0x1c7 + [<c019c6bd>] sysfs_find_dirent+0x1e/0x27 + [<c019c701>] sysfs_add_one+0x3b/0x8b + [<c019c24c>] sysfs_add_file_mode+0x4d/0x76 + [<c019da1c>] internal_create_group+0xd7/0x196 + [<c0322dd2>] klist_next+0x53/0x90 + [<c025809f>] scsi_scan_channel+0x78/0x8d + [<c025815c>] scsi_scan_host_selected+0xa8/0xd1 + [<c02581ed>] do_scsi_scan_host+0x68/0x6a + [<c027e26c>] ahd_linux_register_host+0x267/0x2db + [<c02808cf>] ahd_pci_map_int+0x2c/0x50 + [<c0279bba>] ahd_pci_config+0x533/0x824 + [<c01f6736>] kobject_get+0xf/0x13 + [<c024a495>] get_device+0xe/0x14 + [<c0202579>] pci_dev_get+0xf/0x13 + [<c0280a96>] ahd_linux_pci_dev_probe+0x139/0x17f + [<c019ce3a>] sysfs_addrm_finish+0x14/0x1c7 + [<c019c6bd>] sysfs_find_dirent+0x1e/0x27 + [<c019c701>] sysfs_add_one+0x3b/0x8b + [<c019d3a3>] sysfs_create_link+0x89/0x106 + [<c0202819>] pci_match_device+0x9c/0xad + [<c0202880>] pci_device_probe+0x40/0x60 + [<c024c9d3>] driver_probe_device+0x76/0x152 + [<c024cb05>] __driver_attach+0x56/0x58 + [<c024c40d>] bus_for_each_dev+0x39/0x57 + [<c0202840>] pci_device_probe+0x0/0x60 + [<c024c896>] driver_attach+0x16/0x1a + [<c024caaf>] __driver_attach+0x0/0x58 + [<c024bf1a>] bus_add_driver+0x19c/0x214 + [<c0202534>] pci_device_remove+0x0/0x36 + [<c0202840>] pci_device_probe+0x0/0x60 + [<c024cc24>] driver_register+0x3b/0xd3 + [<c020274b>] __pci_register_driver+0x32/0x64 + [<c040eb5f>] ahd_linux_init+0x53/0x6f + [<c03faa36>] kernel_init+0x11d/0x287 + [<c01174c2>] finish_task_switch+0x1f/0x6d + [<c0117711>] schedule_tail+0x16/0x44 + [<c0102c6a>] ret_from_fork+0x6/0x1c + [<c03fa919>] kernel_init+0x0/0x287 + [<c03fa919>] kernel_init+0x0/0x287 + [<c0103947>] kernel_thread_helper+0x7/0x10 + ======================= +---[ end trace 73ab2f7863b8a5fa ]--- +scsi target1:0:0: asynchronous scsi1:A:0:0: Tagged Queuing enabled. Depth 32 - target1:0:0: Beginning Domain Validation - target1:0:0: wide asynchronous - target1:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) - target1:0:0: Ending Domain Validation +scsi target1:0:0: Beginning Domain Validation +scsi target1:0:0: wide asynchronous +scsi target1:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) +scsi target1:0:0: Ending Domain Validation scsi 1:0:1:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3 - target1:0:1: asynchronous +scsi target1:0:1: asynchronous scsi1:A:1:0: Tagged Queuing enabled. Depth 32 - target1:0:1: Beginning Domain Validation - target1:0:1: wide asynchronous - target1:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) - target1:0:1: Ending Domain Validation +scsi target1:0:1: Beginning Domain Validation +scsi target1:0:1: wide asynchronous +scsi target1:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) +scsi target1:0:1: Ending Domain Validation Driver 'sd' needs updating - please use bus_type methods sd 1:0:0:0: [sda] 71687372 512-byte hardware sectors (36704 MB) sd 1:0:0:0: [sda] Write Protect is off
@@ -353,6 +399,7 @@ usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected +hub 1-0:1.0: unable to enumerate USB device on port 1 ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller
@@ -361,6 +408,7 @@ usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected +hub 1-0:1.0: unable to enumerate USB device on port 4 ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller
@@ -389,61 +437,61 @@ input: Mitsumi Electric Apple Extended USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.1/input/input3 input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0000:00:1d.0-1.3 usbcore: registered new interface driver usbhid -drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver +usbhid: v2.6:USB HID core driver TCP cubic registered -NET: Registered protocol family 1 NET: Registered protocol family 17 p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available Using IPI Shortcut mode kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. -Freeing unused kernel memory: 268k freed -sd 1:0:0:0: Attached scsi generic sg0 type 0 -sd 1:0:1:0: Attached scsi generic sg1 type 0 -sd 2:0:0:0: Attached scsi generic sg2 type 0 -sr 2:0:1:0: Attached scsi generic sg3 type 5 -sd 4:0:0:0: Attached scsi generic sg4 type 0 +Freeing unused kernel memory: 232k freed Linux agpgart interface v0.103 -ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17 -usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3404 -usbcore: registered new interface driver usblp -rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 -rtc0: alarms up to one month agpgart: Detected an Intel i875 Chipset. agpgart: AGP aperture is 32M @ 0xf0000000 Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 Copyright (c) 1999-2006 Intel Corporation. ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:02:01.0 to 64 +usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3404 +usbcore: registered new interface driver usblp e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:a6:8b:e9:85 +sd 1:0:0:0: Attached scsi generic sg0 type 0 +sd 1:0:1:0: Attached scsi generic sg1 type 0 +sd 2:0:0:0: Attached scsi generic sg2 type 0 +sr 2:0:1:0: Attached scsi generic sg3 type 5 +sd 4:0:0:0: Attached scsi generic sg4 type 0 +e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection +ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 20 (level, low) -> IRQ 20 +ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[f6008000-f60087ff] Max Packet=[2048] IR/IT contexts=[4/8] +ACPI: PCI Interrupt 0000:03:0d.0[A] -> GSI 21 (level, low) -> IRQ 21 +3c59x: Donald Becker and others. +0000:03:0d.0: 3Com PCI 3c980C Python-T at f881e000. +ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17 +gameport: EMU10K1 is pci0000:03:0b.1/gameport0, io 0x9400, speed 994kHz +rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 +rtc0: alarms up to one month Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A -parport_pc 00:09: reported by Plug and Play ACPI -parport0: PC-style at 0x378, irq 7 [PCSPP(,...)] -e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection -ACPI: PCI Interrupt 0000:03:0d.0[A] -> GSI 21 (level, low) -> IRQ 21 -3c59x: Donald Becker and others. -0000:03:0d.0: 3Com PCI 3c980C Python-T at f882e000. -udev: renamed network interface eth0 to eth1 -ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 20 (level, low) -> IRQ 20 -ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[f6008000-f60087ff] Max Packet=[2048] IR/IT contexts=[4/8] -ACPI: PCI Interrupt 0000:03:0b.0[A] -> GSI 23 (level, low) -> IRQ 23 -gameport: EMU10K1 is pci0000:03:0b.1/gameport0, io 0x9400, speed 1028kHz ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1f.5 to 64 +parport_pc 00:09: reported by Plug and Play ACPI +parport0: PC-style at 0x378, irq 7 [PCSPP(,...)] +udev: renamed network interface eth1 to eth0 +udev: renamed network interface eth0_rename to eth1 AC'97 0 analog subsections not ready -intel8x0_measure_ac97_clock: measured 50135 usecs +intel8x0_measure_ac97_clock: measured 50110 usecs intel8x0: clocking to 48000 -rtc: I/O resource 70 is not free. +ACPI: PCI Interrupt 0000:03:0b.0[A] -> GSI 23 (level, low) -> IRQ 23 +firmware: requesting intel-ucode/0f-02-09 +firmware: requesting intel-ucode/0f-02-09 IA-32 Microcode Update Driver: v1.14a <[email protected]> -rtc: I/O resource 70 is not free. +ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000063814f] Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 -ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000063814f] EXT3 (no)user_xattr options not supported EXT3 FS on sda1, internal journal EXT3 (no)user_xattr options not supported
Signature · 4 lines
J.A. Magallon <jamagallon()ono!com> \ Software is like sex:
\ It's better when it's free
Mandriva Linux release 2008.1 (Cooker) for i586
Linux 2.6.23-jam05 (gcc 4.2.2 20071128 (4.2.2-2mdv2008.1)) SMP PREEMPTQuoted 11 lines · J.A. Magallón
I have a couple problems with latest git (-14):
- It only recognises 2 processors out of 4 (dual Xeon HT)
- It oopses on the swapper process just on boot...Difference in dmesg is below. If full correct dmesg or config is needed, please ask for them. The kernel was built copying old 2.6.25 config to .config && make oldconfig. I filled the missing gaps like PAT and others...
Review
Quoted 4 lines
(quoted diff) +3
-1-Brought up 4 CPUs +native_cpu_up: bad cpu 2 +native_cpu_up: bad cpu 3 +Brought up 2 CPUs
Yes, I've been getting this for some days too: only 2 processors on dual Xeon HT in 32-bit mode; whereas x86_64 finds all 4 just fine. Ran lots of testing on 2.6.25-mm1 before I noticed it there.
I bisected for a while, but it got confusing (arrived at a bisect point which gave only 1 processor: smpboot code getting rearranged), so I was forced (quel horreur!) to investigate properly. I've just now had success with the patch below, please give it a try:
but it'll need an Ack from Glauber before it can go in.
Quoted 1 line
+WARNING: at
include/linux/blkdev.h:427blk_queue_init_tags+0x110/0x11f()
I presume this warning and backtrace is what you report as an oops:
I think you'll find Linus included a fix for this one overnight, and it should have gone away in 2.6.25-git15 (but I didn't see it myself).
Hugh
[PATCH] x86_32: fix HT cpu booting
Since recent smpboot 32/64-bit merge, my dual Xeon with HT has been booting only 2 of its 4 cpus (when running an i386 kernel; but x86_64 is okay). J.A. Magallón reports the same.
native_cpu_up: bad cpu 2native_cpu_up: bad cpu 3
The mach-default cpu_present_to_apicid() was just returning cpu number (2, 3) instead of apicid (6, 7): looks like we now need the x86_64 code even for the i386 case.
Comparing with other versions of cpu_present_to_apicid(), it seems a good idea to include an NR_CPUS test too, since cpu_present() doesn't include that; but that wasn't a problem here, and may no problem at all.
One point worth noting - is it a worry? Prior to that smpboot merge, my Xeon booted the two HT siblings on one physical first, then the two siblings on the other physical after - when i386, but alternated them when x86_64. Since the merge, the x86_64 sequence is unchanged, but the i386 sequence is now like x86_64. I prefer this consistency, and I prefer the new sequence: booting with maxcpus=2 then uses the independent physicals without HT sharing; but surprises in store?
include/asm-x86/mach-default/mach_apic.h +1 -6
@@ -109,13 +109,8 @@ static inline int cpu_to_logical_apicid(static inline int cpu_present_to_apicid (int mps_cpu) { -#ifdef CONFIG_X86_64 -if (cpu_present (mps_cpu)) +if (mps_cpu <NR_CPUS &&cpu_present (mps_cpu))return (int )per_cpu (x86_bios_cpu_apicid, mps_cpu); -#else -if (mps_cpu <get_physical_broadcast ()) -return mps_cpu; -#endif else return BAD_APICID ; }
Quoted 8 lines · On Wed, 30 Apr 2008 16:17:46 +0100 (BST) Hugh Dickins <[email protected]> wrote:
One point worth noting - is it a worry? Prior to that smpboot merge, my Xeon booted the two HT siblings on one physical first, then the two siblings on the other physical after - when i386, but alternated them when
x86_64. Since the merge, thex86_64sequence is unchanged, but the i386 sequence is now likex86_64. I prefer this consistency, and I prefer the new sequence: booting with maxcpus=2 then uses the independent physicals without HT sharing; but surprises in store?
this is how it always was supposed to be!
At least this is how Intel specifies it to the BIOS vendors (but remember, it's the bios that pretty much sets the cpu order; some will be weird).
Exactly for the maxcpus=2 reason... (and for systems where the cpu scheduler does load balancing "from 0 up" it also makes sense)
Quoted 68 lines · Hugh Dickins
Quoted 10 lines · J.A. Magallón
I have a couple problems with latest git (-14):
- It only recognises 2 processors out of 4 (dual Xeon HT)
- It oopses on the swapper process just on boot...Difference in dmesg is below. If full correct dmesg or config is needed, please ask for them. The kernel was built copying old 2.6.25 config to .config && make oldconfig. I filled the missing gaps like PAT and others...
Review
Quoted 4 lines
(quoted diff) +3
-1-Brought up 4 CPUs +native_cpu_up: bad cpu 2 +native_cpu_up: bad cpu 3 +Brought up 2 CPUsYes, I've been getting this for some days too: only 2 processors on dual Xeon HT in 32-bit mode; whereas
x86_64finds all 4 just fine. Ran lots of testing on 2.6.25-mm1 before I noticed it there.I bisected for a while, but it got confusing (arrived at a bisect point which gave only 1 processor: smpboot code getting rearranged), so I was forced (quel horreur!) to investigate properly. I've just now had success with the patch below, please give it a try:
but it'll need an Ack from Glauber before it can go in.Quoted 1 line
+WARNING: at
include/linux/blkdev.h:427blk_queue_init_tags+0x110/0x11f()I presume this warning and backtrace is what you report as an oops:
I think you'll find Linus included a fix for this one overnight, and it should have gone away in 2.6.25-git15 (but I didn't see it myself).Hugh
[PATCH]
x86_32: fix HT cpu bootingSince recent smpboot 32/64-bit merge, my dual Xeon with HT has been booting only 2 of its 4 cpus (when running an i386 kernel; but
x86_64is okay). J.A. Magallón reports the same.
native_cpu_up: bad cpu 2native_cpu_up: bad cpu 3The mach-default
cpu_present_to_apicid()was just returning cpu number (2, 3) instead of apicid (6, 7): looks like we now need thex86_64code even for the i386 case.Comparing with other versions of
cpu_present_to_apicid(), it seems a good idea to include anNR_CPUStest too, sincecpu_present()doesn't include that; but that wasn't a problem here, and may no problem at all.One point worth noting - is it a worry? Prior to that smpboot merge, my Xeon booted the two HT siblings on one physical first, then the two siblings on the other physical after - when i386, but alternated them when
x86_64. Since the merge, thex86_64sequence is unchanged, but the i386 sequence is now likex86_64. I prefer this consistency, and I prefer the new sequence: booting with maxcpus=2 then uses the independent physicals without HT sharing; but surprises in store?Signed-off-by Hugh Dickins <[email protected]>include/asm-x86/mach-default/mach_apic.h +0
-1@@ -109,13 +109,8 @@ static inline int cpu_to_logical_apicid(static inline int cpu_present_to_apicid (int mps_cpu) { -#ifdef CONFIG_X86_64
include/asm-x86/mach-default/mach_apic.h static inline int cpu_to_logical_apicid( · line 116
Quoted 10 lines
include/asm-x86/mach-default/mach_apic.h +1
-5-if (cpu_present (mps_cpu)) +if (mps_cpu <NR_CPUS &&cpu_present (mps_cpu))return (int )per_cpu (x86_bios_cpu_apicid, mps_cpu); -#else -if (mps_cpu <get_physical_broadcast ()) -return mps_cpu; -#endif else return BAD_APICID ; }
Hugh, thanks for tracing this. The patch looks sane to me
However, since this problem was raised, I'm still concerned that visws may have the same problem, since it uses the same logic that i386 mach_default used to. (and I did not touched, since x86_64 code went int o mach_default).
Could anyone with access to such hardware give it a try ?
Quoted 81 lines · Glauber Costa
Quoted 67 lines · Hugh Dickins
Quoted 10 lines · J.A. Magall??n
I have a couple problems with latest git (-14):
- It only recognises 2 processors out of 4 (dual Xeon HT)
- It oopses on the swapper process just on boot...Difference in dmesg is below. If full correct dmesg or config is needed, please ask for them. The kernel was built copying old 2.6.25 config to .config && make oldconfig. I filled the missing gaps like PAT and others...
Review
Quoted 4 lines
(quoted diff) +3
-1-Brought up 4 CPUs +native_cpu_up: bad cpu 2 +native_cpu_up: bad cpu 3 +Brought up 2 CPUsYes, I've been getting this for some days too: only 2 processors on dual Xeon HT in 32-bit mode; whereas
x86_64finds all 4 just fine. Ran lots of testing on 2.6.25-mm1 before I noticed it there.I bisected for a while, but it got confusing (arrived at a bisect point which gave only 1 processor: smpboot code getting rearranged), so I was forced (quel horreur!) to investigate properly. I've just now had success with the patch below, please give it a try:
but it'll need an Ack from Glauber before it can go in.Quoted 1 line
+WARNING: at
include/linux/blkdev.h:427blk_queue_init_tags+0x110/0x11f()I presume this warning and backtrace is what you report as an oops:
I think you'll find Linus included a fix for this one overnight, and it should have gone away in 2.6.25-git15 (but I didn't see it myself).Hugh
[PATCH]
x86_32: fix HT cpu bootingSince recent smpboot 32/64-bit merge, my dual Xeon with HT has been booting only 2 of its 4 cpus (when running an i386 kernel; but
x86_64is okay). J.A. Magall??n reports the same.
native_cpu_up: bad cpu 2native_cpu_up: bad cpu 3The mach-default
cpu_present_to_apicid()was just returning cpu number (2, 3) instead of apicid (6, 7): looks like we now need thex86_64code even for the i386 case.Comparing with other versions of
cpu_present_to_apicid(), it seems a good idea to include anNR_CPUStest too, sincecpu_present()doesn't include that; but that wasn't a problem here, and may no problem at all.One point worth noting - is it a worry? Prior to that smpboot merge, my Xeon booted the two HT siblings on one physical first, then the two siblings on the other physical after - when i386, but alternated them when
x86_64. Since the merge, thex86_64sequence is unchanged, but the i386 sequence is now likex86_64. I prefer this consistency, and I prefer the new sequence: booting with maxcpus=2 then uses the independent physicals without HT sharing; but surprises in store?Signed-off-by Hugh Dickins <[email protected]>include/asm-x86/mach-default/mach_apic.h +0
-1@@ -109,13 +109,8 @@ static inline int cpu_to_logical_apicid(static inline int cpu_present_to_apicid (int mps_cpu) { -#ifdef CONFIG_X86_64 include/asm-x86/mach-default/mach_apic.h static inline int cpu_to_logical_apicid( · line 115
Quoted 10 lines
include/asm-x86/mach-default/mach_apic.h +1
-5-if (cpu_present (mps_cpu)) +if (mps_cpu <NR_CPUS &&cpu_present (mps_cpu))return (int )per_cpu (x86_bios_cpu_apicid, mps_cpu); -#else -if (mps_cpu <get_physical_broadcast ()) -return mps_cpu; -#endif else return BAD_APICID ; }Hugh, thanks for tracing this. The patch looks sane to me
Quoted 6 lines
However, since this problem was raised, I'm still concerned that visws may have the same problem, since it uses the same logic that i386
mach_defaultused to. (and I did not touched, sincex86_64code went int omach_default).Could anyone with access to such hardware give it a try ?
Unfortunately, no. Visws port is in non-bootable state currently, 2.6.25 hangs in calibrate_delay_direct() and I still do not know why :(
Signature · 2 lines
Andrey Panin | Linux and UNIX system administrator [email protected] | PGP key: wwwkeys.pgp.net
Quoted 9 lines · Andrey Panin
Quoted 6 lines
However, since this problem was raised, I'm still concerned that visws may have the same problem, since it uses the same logic that i386
mach_defaultused to. (and I did not touched, sincex86_64code went int omach_default).Could anyone with access to such hardware give it a try ?
Unfortunately, no. Visws port is in non-bootable state currently, 2.6.25 hangs in
calibrate_delay_direct()and I still do not know why :(
What was the last kernel which booted on visws ?
Thanks,
tglx
Ingo Molnar
Appliedinclude/asm-x86/mach-default/mach_apic.h static inline int cpu_to_logical_apicid( · line 116
Quoted 13 lines · Hugh Dickins
static inline int
cpu_present_to_apicid(int mps_cpu){include/asm-x86/mach-default/mach_apic.h +1
-6-#ifdef CONFIG_X86_64 -if (cpu_present (mps_cpu)) +if (mps_cpu <NR_CPUS &&cpu_present (mps_cpu))return (int )per_cpu (x86_bios_cpu_apicid, mps_cpu); -#else -if (mps_cpu <get_physical_broadcast ()) -return mps_cpu; -#endif else return BAD_APICID ; }
applied. Thanks Hugh for the detective work! I love fixes that only remove code ;-)
Ingo
Quoted 7 lines · Hugh Dickins
One point worth noting - is it a worry? Prior to that smpboot merge, my Xeon booted the two HT siblings on one physical first, then the two siblings on the other physical after - when i386, but alternated them when
x86_64. Since the merge, thex86_64sequence is unchanged, but the i386 sequence is now likex86_64. I prefer this consistency, and I prefer the new sequence: booting with maxcpus=2 then uses the independent physicals without HT sharing; but surprises in store?
yep - but right now our view is that such surprises are worth having in this case. Basically we now did the more or less "mechanical" unification of the two SMP boot codebases, while trying to keep the stability track record of both, as much as possible.
The 64-bit SMP boot code (the one which came from arch/x86_64) is cleaner, so the plan is to slowly but surely gravitate towards the cleaner code - such as with your fix - while not dropping quirks and legacies.
It's now possible to do that without impacting the stability (and legacy) track record of the 32-bit code too much, because now the code is placed next to each other and the differences are plain visible via ugly #ifdefs. Whatever change we do is small and revertable.
... but it's still not easy to modify the engine of a race car, in the middle of the race - so please be on the lookout and any help is welcome ;-)
Ingo
Quoted 12 lines · Hugh Dickins
Quoted 4 lines · J.A. Magallón
I have a couple problems with latest git (-14):
- It only recognises 2 processors out of 4 (dual Xeon HT)
[PATCH]
x86_32: fix HT cpu bootingSince recent smpboot 32/64-bit merge, my dual Xeon with HT has been booting only 2 of its 4 cpus (when running an i386 kernel; but
x86_64is okay). J.A. Magallón reports the same.
Quoted 7 lines
native_cpu_up: bad cpu 2native_cpu_up: bad cpu 3The mach-default
cpu_present_to_apicid()was just returning cpu number (2, 3) instead of apicid (6, 7): looks like we now need thex86_64code even for the i386 case.
One question that always bugs me: do I have to set NR_CPUS=8 to pick apicid number 7, and let the map just flag the ones I have, or will it work with NR_CPUS=4 ?
Signature · 4 lines
J.A. Magallon <jamagallon()ono!com> \ Software is like sex:
\ It's better when it's free
Mandriva Linux release 2008.1 (Cooker) for i586
Linux 2.6.23-jam05 (gcc 4.2.2 20071128 (4.2.2-2mdv2008.1)) SMP PREEMPTQuoted 2 lines · J.A. Magallón
Quoted 2 lines
Quoted 2 lines
(dual Xeon HT)
...
Quoted 3 lines
One question that always bugs me: do I have to set NR_CPUS=8 to pick apicid number 7, and let the map just flag the ones I have,
No, that would be unbearable (few understand the logic of those ids).
Quoted 1 line
or will it work with NR_CPUS=4 ?
Yes, that works (and it's intended to work that way).
Hugh
Quoted 27 lines · Hugh Dickins
Quoted 11 lines · J.A. Magallón
I have a couple problems with latest git (-14):
- It only recognises 2 processors out of 4 (dual Xeon HT)
- It oopses on the swapper process just on boot...Difference in dmesg is below. If full correct dmesg or config is needed, please ask for them. The kernel was built copying old 2.6.25 config to .config && make oldconfig. I filled the missing gaps like PAT and others...
Review
Quoted 4 lines
(quoted diff) +3
-1-Brought up 4 CPUs +native_cpu_up: bad cpu 2 +native_cpu_up: bad cpu 3 +Brought up 2 CPUsYes, I've been getting this for some days too: only 2 processors on dual Xeon HT in 32-bit mode; whereas
x86_64finds all 4 just fine. Ran lots of testing on 2.6.25-mm1 before I noticed it there.I bisected for a while, but it got confusing (arrived at a bisect point which gave only 1 processor: smpboot code getting rearranged), so I was forced (quel horreur!) to investigate properly. I've just now had success with the patch below, please give it a try:
but it'll need an Ack from Glauber before it can go in.
Quoted 7 lines
Quoted 1 line
+WARNING: at
include/linux/blkdev.h:427blk_queue_init_tags+0x110/0x11f()I presume this warning and backtrace is what you report as an oops:
I think you'll find Linus included a fix for this one overnight, and it should have gone away in 2.6.25-git15 (but I didn't see it myself).Hugh
-git16 plus your patch gives me my 4 cpus again.
But I still get the warning:
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
ACPI: PCI Interrupt 0000:03:0a.1[B] -> GSI 23 (level, low) -> IRQ 23
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
scsi 1:0:0:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3
------------[ cut here ]------------
WARNING: at include/linux/blkdev.h:431 blk_queue_init_tags+0x110/0x11f()
Modules linked in:
Pid: 1, comm: swapper Not tainted 2.6.25-jam03 #1
[<c011e618>] warn_on_slowpath+0x4d/0x66
[<c0132e68>] __atomic_notifier_call_chain+0x27/0x48
[<c0132ea0>] atomic_notifier_call_chain+0x17/0x1b
[<c024a7be>] notify_update+0x1f/0x23
[<c024aa07>] vt_console_print+0x1dd/0x2ab
[<c024a82a>] vt_console_print+0x0/0x2ab
[<c0132a2e>] up+0x9/0x2b
[<c01f314c>] init_tag_map+0x4e/0x95
[<c01f3271>] __blk_queue_init_tags+0x27/0x4e
[<c01f33a8>] blk_queue_init_tags+0x110/0x11f
[<c0285b9b>] ahd_platform_set_tags+0x177/0x1a7
[<c0286247>] ahd_linux_slave_configure+0xcd/0x131
[<c025e89e>] scsi_probe_and_add_lun+0x706/0x964
[<c025ecc7>] __scsi_scan_target+0xd9/0x5d9
[<c019ce63>] sysfs_ilookup_test+0x0/0xd
[<c019d8ea>] sysfs_addrm_finish+0x14/0x1c7
[<c019d16d>] sysfs_find_dirent+0x1e/0x27
[<c019d1b1>] sysfs_add_one+0x3b/0x8b
[<c019ccfc>] sysfs_add_file_mode+0x4d/0x76
[<c019e4cc>] internal_create_group+0xd7/0x196
[<c032a1b2>] klist_next+0x53/0x90
[<c025f23f>] scsi_scan_channel+0x78/0x8d
[<c025f2fc>] scsi_scan_host_selected+0xa8/0xd1
[<c025f38d>] do_scsi_scan_host+0x68/0x6a
[<c028540c>] ahd_linux_register_host+0x267/0x2db
[<c0287a6f>] ahd_pci_map_int+0x2c/0x50
[<c0280d5a>] ahd_pci_config+0x533/0x824
[<c01fce96>] kobject_get+0xf/0x13
[<c0251635>] get_device+0xe/0x14
[<c0208da9>] pci_dev_get+0xf/0x13
[<c0287c36>] ahd_linux_pci_dev_probe+0x139/0x17f
[<c019d8ea>] sysfs_addrm_finish+0x14/0x1c7
[<c019d16d>] sysfs_find_dirent+0x1e/0x27
[<c019d1b1>] sysfs_add_one+0x3b/0x8b
[<c019de53>] sysfs_create_link+0x89/0x106
[<c0209049>] pci_match_device+0x9c/0xad
[<c02090b0>] pci_device_probe+0x40/0x60
[<c0253b73>] driver_probe_device+0x76/0x152
[<c0253ca5>] __driver_attach+0x56/0x58
[<c02535ad>] bus_for_each_dev+0x39/0x57
[<c0209070>] pci_device_probe+0x0/0x60
[<c0253a36>] driver_attach+0x16/0x1a
[<c0253c4f>] __driver_attach+0x0/0x58
[<c02530ba>] bus_add_driver+0x19c/0x214
[<c0208d64>] pci_device_remove+0x0/0x36
[<c0209070>] pci_device_probe+0x0/0x60
[<c0253dc4>] driver_register+0x3b/0xd3
[<c0208f7b>] __pci_register_driver+0x32/0x64
[<c041abff>] ahd_linux_init+0x53/0x6f
[<c0406a36>] kernel_init+0x11d/0x287
[<c01174c2>] finish_task_switch+0x1f/0x6d
[<c0117711>] schedule_tail+0x16/0x44
[<c0102c62>] ret_from_fork+0x6/0x1c
[<c0406919>] kernel_init+0x0/0x287
[<c0406919>] kernel_init+0x0/0x287
[<c010393f>] kernel_thread_helper+0x7/0x18
=======================
---[ end trace e7ca32af98aeff40 ]---scsi target1:0:0: asynchronous
scsi1:A:0:0: Tagged Queuing enabled. Depth 32
scsi target1:0:0: Beginning Domain Validation
scsi target1:0:0: wide asynchronous
scsi target1:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) scsi target1:0:0: Ending Domain Validation
scsi 1:0:1:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3
scsi target1:0:1: asynchronous
scsi1:A:1:0: Tagged Queuing enabled. Depth 32
scsi target1:0:1: Beginning Domain Validation
scsi target1:0:1: wide asynchronous
scsi target1:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) scsi target1:0:1: Ending Domain Validation
Driver 'sd' needs updating - please use bus_type methods
sd 1:0:0:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: ab 00 10 08
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:0:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: ab 00 10 08
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:1:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: ab 00 10 08
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:1:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: ab 00 10 08
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: sdb1
sd 1:0:1:0: [sdb] Attached SCSI disk
Signature · 4 lines
J.A. Magallon <jamagallon()ono!com> \ Software is like sex:
\ It's better when it's free
Mandriva Linux release 2008.1 (Cooker) for i586
Linux 2.6.23-jam05 (gcc 4.2.2 20071128 (4.2.2-2mdv2008.1)) SMP PREEMPTQuoted 12 lines · J.A. Magallón
Quoted 11 lines · Hugh Dickins
Quoted 10 lines · J.A. Magallón
I have a couple problems with latest git (-14):
- It only recognises 2 processors out of 4 (dual Xeon HT)
- It oopses on the swapper process just on boot...Difference in dmesg is below. If full correct dmesg or config is needed, please ask for them. The kernel was built copying old 2.6.25 config to .config && make oldconfig. I filled the missing gaps like PAT and others...
...
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
+WARNING: at
include/linux/blkdev.h:427blk_queue_init_tags+0x110/0x11f()I presume this warning and backtrace is what you report as an oops:
I think you'll find Linus included a fix for this one overnight, and it should have gone away in 2.6.25-git15 (but I didn't see it myself).-git16 plus your patch gives me my 4 cpus again.
I'm glad to hear this, thanks.
Quoted 1 line
But I still get the warning:
But sorry to hear this. That warning has undergone several revisions
already: I expect yours is another false positive not to worry about, but it still needs to be fixed. I won't meddle in there, Cc'ed Jens and Nick who will know what's appropriate.
Hugh
Quoted 105 lines
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs ACPI: PCI Interrupt 0000:03:0a.1[B] -> GSI 23 (level, low) -> IRQ 23 scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 <Adaptec 29320 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs scsi 1:0:0:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3 ------------[ cut here ]------------ WARNING: at include/linux/blkdev.h:431 blk_queue_init_tags+0x110/0x11f() Modules linked in: Pid: 1, comm: swapper Not tainted 2.6.25-jam03 #1 [<c011e618>] warn_on_slowpath+0x4d/0x66 [<c0132e68>] __atomic_notifier_call_chain+0x27/0x48 [<c0132ea0>] atomic_notifier_call_chain+0x17/0x1b [<c024a7be>] notify_update+0x1f/0x23 [<c024aa07>] vt_console_print+0x1dd/0x2ab [<c024a82a>] vt_console_print+0x0/0x2ab [<c0132a2e>] up+0x9/0x2b [<c01f314c>] init_tag_map+0x4e/0x95 [<c01f3271>] __blk_queue_init_tags+0x27/0x4e [<c01f33a8>] blk_queue_init_tags+0x110/0x11f [<c0285b9b>] ahd_platform_set_tags+0x177/0x1a7 [<c0286247>] ahd_linux_slave_configure+0xcd/0x131 [<c025e89e>] scsi_probe_and_add_lun+0x706/0x964 [<c025ecc7>] __scsi_scan_target+0xd9/0x5d9 [<c019ce63>] sysfs_ilookup_test+0x0/0xd [<c019d8ea>] sysfs_addrm_finish+0x14/0x1c7 [<c019d16d>] sysfs_find_dirent+0x1e/0x27 [<c019d1b1>] sysfs_add_one+0x3b/0x8b [<c019ccfc>] sysfs_add_file_mode+0x4d/0x76 [<c019e4cc>] internal_create_group+0xd7/0x196 [<c032a1b2>] klist_next+0x53/0x90 [<c025f23f>] scsi_scan_channel+0x78/0x8d [<c025f2fc>] scsi_scan_host_selected+0xa8/0xd1 [<c025f38d>] do_scsi_scan_host+0x68/0x6a [<c028540c>] ahd_linux_register_host+0x267/0x2db [<c0287a6f>] ahd_pci_map_int+0x2c/0x50 [<c0280d5a>] ahd_pci_config+0x533/0x824 [<c01fce96>] kobject_get+0xf/0x13 [<c0251635>] get_device+0xe/0x14 [<c0208da9>] pci_dev_get+0xf/0x13 [<c0287c36>] ahd_linux_pci_dev_probe+0x139/0x17f [<c019d8ea>] sysfs_addrm_finish+0x14/0x1c7 [<c019d16d>] sysfs_find_dirent+0x1e/0x27 [<c019d1b1>] sysfs_add_one+0x3b/0x8b [<c019de53>] sysfs_create_link+0x89/0x106 [<c0209049>] pci_match_device+0x9c/0xad [<c02090b0>] pci_device_probe+0x40/0x60 [<c0253b73>] driver_probe_device+0x76/0x152 [<c0253ca5>] __driver_attach+0x56/0x58 [<c02535ad>] bus_for_each_dev+0x39/0x57 [<c0209070>] pci_device_probe+0x0/0x60 [<c0253a36>] driver_attach+0x16/0x1a [<c0253c4f>] __driver_attach+0x0/0x58 [<c02530ba>] bus_add_driver+0x19c/0x214 [<c0208d64>] pci_device_remove+0x0/0x36 [<c0209070>] pci_device_probe+0x0/0x60 [<c0253dc4>] driver_register+0x3b/0xd3 [<c0208f7b>] __pci_register_driver+0x32/0x64 [<c041abff>] ahd_linux_init+0x53/0x6f [<c0406a36>] kernel_init+0x11d/0x287 [<c01174c2>] finish_task_switch+0x1f/0x6d [<c0117711>] schedule_tail+0x16/0x44 [<c0102c62>] ret_from_fork+0x6/0x1c [<c0406919>] kernel_init+0x0/0x287 [<c0406919>] kernel_init+0x0/0x287 [<c010393f>] kernel_thread_helper+0x7/0x18 ======================= ---[ end trace e7ca32af98aeff40 ]---scsi target1:0:0: asynchronous
scsi1:A:0:0: Tagged Queuing enabled. Depth 32
scsi target1:0:0: Beginning Domain Validation
scsi target1:0:0: wide asynchronous
scsi target1:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) scsi target1:0:0: Ending Domain Validation
scsi 1:0:1:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3
scsi target1:0:1: asynchronous
scsi1:A:1:0: Tagged Queuing enabled. Depth 32
scsi target1:0:1: Beginning Domain Validation
scsi target1:0:1: wide asynchronous
scsi target1:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) scsi target1:0:1: Ending Domain Validation
Driver 'sd' needs updating - please usebus_typemethods
sd 1:0:0:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: ab 00 10 08
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:0:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: ab 00 10 08
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:1:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: ab 00 10 08
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:1:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: ab 00 10 08
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: sdb1
sd 1:0:1:0: [sdb] Attached SCSI disk
Quoted 22 lines · Hugh Dickins
Quoted 12 lines · J.A. Magallón
Quoted 11 lines · Hugh Dickins
Quoted 10 lines · J.A. Magallón
I have a couple problems with latest git (-14):
- It only recognises 2 processors out of 4 (dual Xeon HT)
- It oopses on the swapper process just on boot...Difference in dmesg is below. If full correct dmesg or config is needed, please ask for them. The kernel was built copying old 2.6.25 config to .config && make oldconfig. I filled the missing gaps like PAT and others...
...
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
+WARNING: at
include/linux/blkdev.h:427blk_queue_init_tags+0x110/0x11f()I presume this warning and backtrace is what you report as an oops:
I think you'll find Linus included a fix for this one overnight, and it should have gone away in 2.6.25-git15 (but I didn't see it myself).-git16 plus your patch gives me my 4 cpus again.
Quoted 8 lines
I'm glad to hear this, thanks.
Quoted 1 line
But I still get the warning:
But sorry to hear this. That warning has undergone several revisions
already: I expect yours is another false positive not to worry about, but it still needs to be fixed. I won't meddle in there, Cc'ed Jens and Nick who will know what's appropriate.
Thanks for the heads up Hugh. I think we're OK at this point because we're running in allocation/setup code so there should be no concurrency on queue_flags. I remember following this call chain and making this conclusion (hopefully correct, Jens?)... however I don't know how I concluded that the warning would not fire.
Quoted 108 lines
Hugh
Quoted 105 lines
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs ACPI: PCI Interrupt 0000:03:0a.1[B] -> GSI 23 (level, low) -> IRQ 23 scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 <Adaptec 29320 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs scsi 1:0:0:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3 ------------[ cut here ]------------ WARNING: at include/linux/blkdev.h:431 blk_queue_init_tags+0x110/0x11f() Modules linked in: Pid: 1, comm: swapper Not tainted 2.6.25-jam03 #1 [<c011e618>] warn_on_slowpath+0x4d/0x66 [<c0132e68>] __atomic_notifier_call_chain+0x27/0x48 [<c0132ea0>] atomic_notifier_call_chain+0x17/0x1b [<c024a7be>] notify_update+0x1f/0x23 [<c024aa07>] vt_console_print+0x1dd/0x2ab [<c024a82a>] vt_console_print+0x0/0x2ab [<c0132a2e>] up+0x9/0x2b [<c01f314c>] init_tag_map+0x4e/0x95 [<c01f3271>] __blk_queue_init_tags+0x27/0x4e [<c01f33a8>] blk_queue_init_tags+0x110/0x11f [<c0285b9b>] ahd_platform_set_tags+0x177/0x1a7 [<c0286247>] ahd_linux_slave_configure+0xcd/0x131 [<c025e89e>] scsi_probe_and_add_lun+0x706/0x964 [<c025ecc7>] __scsi_scan_target+0xd9/0x5d9 [<c019ce63>] sysfs_ilookup_test+0x0/0xd [<c019d8ea>] sysfs_addrm_finish+0x14/0x1c7 [<c019d16d>] sysfs_find_dirent+0x1e/0x27 [<c019d1b1>] sysfs_add_one+0x3b/0x8b [<c019ccfc>] sysfs_add_file_mode+0x4d/0x76 [<c019e4cc>] internal_create_group+0xd7/0x196 [<c032a1b2>] klist_next+0x53/0x90 [<c025f23f>] scsi_scan_channel+0x78/0x8d [<c025f2fc>] scsi_scan_host_selected+0xa8/0xd1 [<c025f38d>] do_scsi_scan_host+0x68/0x6a [<c028540c>] ahd_linux_register_host+0x267/0x2db [<c0287a6f>] ahd_pci_map_int+0x2c/0x50 [<c0280d5a>] ahd_pci_config+0x533/0x824 [<c01fce96>] kobject_get+0xf/0x13 [<c0251635>] get_device+0xe/0x14 [<c0208da9>] pci_dev_get+0xf/0x13 [<c0287c36>] ahd_linux_pci_dev_probe+0x139/0x17f [<c019d8ea>] sysfs_addrm_finish+0x14/0x1c7 [<c019d16d>] sysfs_find_dirent+0x1e/0x27 [<c019d1b1>] sysfs_add_one+0x3b/0x8b [<c019de53>] sysfs_create_link+0x89/0x106 [<c0209049>] pci_match_device+0x9c/0xad [<c02090b0>] pci_device_probe+0x40/0x60 [<c0253b73>] driver_probe_device+0x76/0x152 [<c0253ca5>] __driver_attach+0x56/0x58 [<c02535ad>] bus_for_each_dev+0x39/0x57 [<c0209070>] pci_device_probe+0x0/0x60 [<c0253a36>] driver_attach+0x16/0x1a [<c0253c4f>] __driver_attach+0x0/0x58 [<c02530ba>] bus_add_driver+0x19c/0x214 [<c0208d64>] pci_device_remove+0x0/0x36 [<c0209070>] pci_device_probe+0x0/0x60 [<c0253dc4>] driver_register+0x3b/0xd3 [<c0208f7b>] __pci_register_driver+0x32/0x64 [<c041abff>] ahd_linux_init+0x53/0x6f [<c0406a36>] kernel_init+0x11d/0x287 [<c01174c2>] finish_task_switch+0x1f/0x6d [<c0117711>] schedule_tail+0x16/0x44 [<c0102c62>] ret_from_fork+0x6/0x1c [<c0406919>] kernel_init+0x0/0x287 [<c0406919>] kernel_init+0x0/0x287 [<c010393f>] kernel_thread_helper+0x7/0x18 ======================= ---[ end trace e7ca32af98aeff40 ]---scsi target1:0:0: asynchronous
scsi1:A:0:0: Tagged Queuing enabled. Depth 32
scsi target1:0:0: Beginning Domain Validation
scsi target1:0:0: wide asynchronous
scsi target1:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) scsi target1:0:0: Ending Domain Validation
scsi 1:0:1:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3
scsi target1:0:1: asynchronous
scsi1:A:1:0: Tagged Queuing enabled. Depth 32
scsi target1:0:1: Beginning Domain Validation
scsi target1:0:1: wide asynchronous
scsi target1:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63) scsi target1:0:1: Ending Domain Validation
Driver 'sd' needs updating - please usebus_typemethods
sd 1:0:0:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: ab 00 10 08
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:0:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: ab 00 10 08
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:1:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: ab 00 10 08
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:1:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: ab 00 10 08
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: sdb1
sd 1:0:1:0: [sdb] Attached SCSI disk
Quoted 32 lines · Nick Piggin
Quoted 22 lines · Hugh Dickins
Quoted 12 lines · J.A. Magallón
Quoted 11 lines · Hugh Dickins
Quoted 10 lines · J.A. Magallón
I have a couple problems with latest git (-14):
- It only recognises 2 processors out of 4 (dual Xeon HT)
- It oopses on the swapper process just on boot...Difference in dmesg is below. If full correct dmesg or config is needed, please ask for them. The kernel was built copying old 2.6.25 config to .config && make oldconfig. I filled the missing gaps like PAT and others...
...
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
+WARNING: at
include/linux/blkdev.h:427blk_queue_init_tags+0x110/0x11f()I presume this warning and backtrace is what you report as an oops:
I think you'll find Linus included a fix for this one overnight, and it should have gone away in 2.6.25-git15 (but I didn't see it myself).-git16 plus your patch gives me my 4 cpus again.
Quoted 8 lines
I'm glad to hear this, thanks.
Quoted 1 line
But I still get the warning:
But sorry to hear this. That warning has undergone several revisions
already: I expect yours is another false positive not to worry about, but it still needs to be fixed. I won't meddle in there, Cc'ed Jens and Nick who will know what's appropriate.
Quoted 5 lines
Thanks for the heads up Hugh. I think we're OK at this point because we're running in allocation/setup code so there should be no concurrency on
queue_flags. I remember following this call chain and making this conclusion (hopefully correct, Jens?)... however I don't know how I concluded that the warning would not fire.
That's USUALLY correct, but not always. If blk_queue_init_tags() is called for resizing depth, then it's a running queue and we should not use _unlocked() for that. So basically they can all be _unlocked() due to lack of concurrency at init time, but not this one:
} else if (q->queue_tags) {
rc = blk_queue_resize_tags(q, depth);
if (rc)
return rc;
queue_flag_set(QUEUE_FLAG_QUEUED, q);
return 0;
} ...So if a driver ever re-calls blk_queue_init_tags() with a tag map already set, then it needs to hold the queue lock.
Signature · 1 line
Jens Axboe