Skip to contentSkip to conversation

Bug with keyboard input

DISCUSSION [email protected] 2 participants 4 messages May 13, 2008 – May 15, 2008

lore
Share & tools
lore
#0 lore raw

Hi list,

With uptodate Fedora 7 (kernel kernel-2.6.23.15-80.fc7) on a Dell D430 laptop.

In short, if I do

	echo -n "i8042" > /sys/bus/platform/drivers/i8042/unbind
followed by
	echo -n "i8042" > /sys/bus/platform/drivers/i8042/bind

everything works fine, EXCEPT if I hit a key on the keyboard between the unbind and the bind (tested with leftcontrol and spacebar). If I hit a key, it looks like the keyboard isn't taking release events anymore and the next key I hit is forever repeated. When my keyboard is in its working state, I read
N: Name="AT Translated Set 2 keyboard"
in /proc/bus/input/devices. When it is in its non-working state (I hit a key between unbind and bind), I read
N: Name="AT Raw Set 2 keyboard"
in the same file, and each time I hit a key, I have messages such as
atkbd.c: Unknown key pressed (raw set 2, code 0x11f on isa0060/serio0). atkbd.c: Use 'setkeycodes 1f <keycode>' to make it known. atkbd.c: Unknown key pressed (raw set 2, code 0x11e on isa0060/serio0). atkbd.c: Use 'setkeycodes 1e <keycode>' to make it known.
in my logs.

Note that the key doesn't have to be pressed while the bind happens, it is sufficient that the key have been pressed and released before the bind.

So, is there a way to make it work and have the input layer automatically recognize the correct keyboard type or keyboard mode ? If not, is there a way to keep it from guessing and to force it to treat the keyboard as an "AT Translated Set 2 keyboard" ?

As a final note, I get hit by this bug quite often during suspend/resume cycles. I had found that the keyboard wasn't all the time properly waking up, (it was getting stuck) so I've added a file in /etc/pm/sleep.d to do the unbind at suspend time and the bind at resume time. This fixed my problem, except that at times I stupidly press a key in the hope that the resume is done and that the screen is black only because of the screensaver, and that hitting a key will make appear the unlocking window...

Thanks,

Éric Brunet

#1 lore raw
Quoted 4 lines · On 05/13/2008 11:27 AM, [email protected] wrote:

Hi list,

With uptodate Fedora 7 (kernel kernel-2.6.23.15-80.fc7) on a Dell D430 laptop.

Please file a bug on redhat bugzilla. They (like other distro providers) have bunch of patches included in it.

Or try some kernel.org tree and recheck if the problem persist, then report it here.

#2 lore raw
Quoted 9 lines · Jiri Slaby
Quoted 3 lines · On 05/13/2008 11:27 AM, [email protected] wrote:

Hi list,

With uptodate Fedora 7 (kernel kernel-2.6.23.15-80.fc7) on a Dell D430 laptop.

Please file a bug on redhat bugzilla. They (like other distro providers) have bunch of patches included in it.

Or try some kernel.org tree and recheck if the problem persist, then report it here.

Well that's not the sort of things distributions are patching, but you're of course right, it is better to make sure. So I downloaded the sources of a linux-2.6.25, copied the fedora .config, ran make oldconfig and made the default answer to every question. With that pristine kernel, the bug is still here.

Thanks,

Éric Brunet

Quoted 40 lines

In short, if I do

        echo -n "i8042" > /sys/bus/platform/drivers/i8042/unbind
followed by
        echo -n "i8042" > /sys/bus/platform/drivers/i8042/bind

everything works fine, EXCEPT if I hit a key on the keyboard between the unbind and the bind (tested with leftcontrol and spacebar). If I hit a key, it looks like the keyboard isn't taking release events anymore and the next key I hit is forever repeated. When my keyboard is in its working
state, I read
N: Name="AT Translated Set 2 keyboard"
in /proc/bus/input/devices. When it is in its non-working state (I hit a key between unbind and bind), I read
N: Name="AT Raw Set 2 keyboard"
in the same file, and each time I hit a key, I have messages such as

    atkbd.c: Unknown key pressed (raw set 2, code 0x11f on

isa0060/serio0).
atkbd.c: Use 'setkeycodes 1f <keycode>' to make it known. atkbd.c: Unknown key pressed (raw set 2, code 0x11e on
isa0060/serio0).
atkbd.c: Use 'setkeycodes 1e <keycode>' to make it known.
in my logs.

Note that the key doesn't have to be pressed while the bind happens, it is sufficient that the key have been pressed and released before the bind.

So, is there a way to make it work and have the input layer automatically recognize the correct keyboard type or keyboard mode ? If not, is there a way to keep it from guessing and to force it to treat the keyboard as an "AT Translated Set 2 keyboard" ?

As a final note, I get hit by this bug quite often during suspend/resume cycles. I had found that the keyboard wasn't all the time properly waking up, (it was getting stuck) so I've added a file in /etc/pm/sleep.d to do the unbind at suspend time and the bind at resume time. This fixed my problem, except that at times I stupidly press a key in the hope that the resume is done and that the screen is black only because of the screensaver, and that hitting a key will make appear the unlocking window...

#3 lore raw

[email protected] napsal(a):

Quoted 10 lines · Jiri Slaby
Quoted 7 lines · On 05/13/2008 11:27 AM, [email protected] wrote:
Quoted 3 lines

Hi list,

With uptodate Fedora 7 (kernel kernel-2.6.23.15-80.fc7) on a Dell D430 laptop.

Please file a bug on redhat bugzilla. They (like other distro providers) have bunch of patches included in it.

Or try some kernel.org tree and recheck if the problem persist, then report it here.

Well that's not the sort of things distributions are patching,

Why do you think so? It could have been caused by some core patches or whatever.

Quoted 5 lines

but you're
of course right, it is better to make sure. So I downloaded the sources of a linux-2.6.25, copied the fedora .config, ran make oldconfig and made the default answer to every question. With that pristine kernel, the bug is still here.

Then please CC input people on your original post.