Skip to contentSkip to conversation

S3C24XX SD/MMC maintainer

PATCH In review Ben Dooks 4 participants 28 messages Jun 30, 2008 MMC, SD and SDIO

lore
Share & tools
lore

Ben Dooks

author
#0 lore raw

v4 cover S3C24XX SD/MMC maintainer

This is an update series for the Samsung S3C24XX SoC series SD/MMC controller, originally by Thomas Kleffel and updated by Ben Dooks.

This patch set has multiple authours as it has been gathered from various sources, including the OpenMoko project.

Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#1 lore raw

PATCH v4 1/17 MMC: S3C24XX MMC/SD driver.

From: Thomas Kleffel <[email protected]>

This is the latest S3C MMC/SD driver by Thomas Kleffel

include/asm-arm/arch-s3c2410/regs-sdi.h +17 -3
Index: linux-2.6.26-rc6-sdmmc/include/asm-arm/arch-s3c2410/regs-sdi.h
===================================================================
@@ -28,9 +28,15 @@
 #define S3C2410_SDIDCNT               (0x30)
 #define S3C2410_SDIDSTA               (0x34)
 #define S3C2410_SDIFSTA               (0x38)
+
 #define S3C2410_SDIDATA               (0x3C)
 #define S3C2410_SDIIMSK               (0x40)
 
+#define S3C2440_SDIDATA               (0x40)
+#define S3C2440_SDIIMSK               (0x3C)
+
+#define S3C2440_SDICON_SDRESET        (1<<8)
+#define S3C2440_SDICON_MMCCLOCK       (1<<5)
 #define S3C2410_SDICON_BYTEORDER      (1<<4)
 #define S3C2410_SDICON_SDIOIRQ        (1<<3)
 #define S3C2410_SDICON_RWAITEN        (1<<2)
@@ -42,7 +48,8 @@
 #define S3C2410_SDICMDCON_LONGRSP     (1<<10)
 #define S3C2410_SDICMDCON_WAITRSP     (1<<9)
 #define S3C2410_SDICMDCON_CMDSTART    (1<<8)
-#define S3C2410_SDICMDCON_INDEX       (0xff)
+#define S3C2410_SDICMDCON_SENDERHOST  (1<<6)
+#define S3C2410_SDICMDCON_INDEX       (0x3f)
 
 #define S3C2410_SDICMDSTAT_CRCFAIL    (1<<12)
 #define S3C2410_SDICMDSTAT_CMDSENT    (1<<11)
@@ -51,6 +58,9 @@
 #define S3C2410_SDICMDSTAT_XFERING    (1<<8)
 #define S3C2410_SDICMDSTAT_INDEX      (0xff)
 
+#define S3C2440_SDIDCON_DS_BYTE       (0<<22)
+#define S3C2440_SDIDCON_DS_HALFWORD   (1<<22)
+#define S3C2440_SDIDCON_DS_WORD       (2<<22)
 #define S3C2410_SDIDCON_IRQPERIOD     (1<<21)
 #define S3C2410_SDIDCON_TXAFTERRESP   (1<<20)
 #define S3C2410_SDIDCON_RXAFTERCMD    (1<<19)
@@ -59,6 +69,7 @@
 #define S3C2410_SDIDCON_WIDEBUS       (1<<16)
 #define S3C2410_SDIDCON_DMAEN         (1<<15)
 #define S3C2410_SDIDCON_STOP          (1<<14)
+#define S3C2440_SDIDCON_DATSTART      (1<<14)
 #define S3C2410_SDIDCON_DATMODE	      (3<<12)
 #define S3C2410_SDIDCON_BLKNUM        (0x7ff)
 
@@ -68,6 +79,7 @@
 #define S3C2410_SDIDCON_XFER_RXSTART  (2<<12)
 #define S3C2410_SDIDCON_XFER_TXSTART  (3<<12)
 
+#define S3C2410_SDIDCON_BLKNUM_MASK   (0xFFF)
 #define S3C2410_SDIDCNT_BLKNUM_SHIFT  (12)
 
 #define S3C2410_SDIDSTA_RDYWAITREQ    (1<<10)
@@ -82,10 +94,12 @@
 #define S3C2410_SDIDSTA_TXDATAON      (1<<1)
 #define S3C2410_SDIDSTA_RXDATAON      (1<<0)
 
+#define S3C2440_SDIFSTA_FIFORESET      (1<<16)
+#define S3C2440_SDIFSTA_FIFOFAIL       (3<<14)  /* 3 is correct (2 bits) */
 #define S3C2410_SDIFSTA_TFDET          (1<<13)
 #define S3C2410_SDIFSTA_RFDET          (1<<12)
-#define S3C2410_SDIFSTA_TXHALF         (1<<11)
-#define S3C2410_SDIFSTA_TXEMPTY        (1<<10)
+#define S3C2410_SDIFSTA_TFHALF         (1<<11)
+#define S3C2410_SDIFSTA_TFEMPTY        (1<<10)
 #define S3C2410_SDIFSTA_RFLAST         (1<<9)
 #define S3C2410_SDIFSTA_RFFULL         (1<<8)
 #define S3C2410_SDIFSTA_RFHALF         (1<<7)
drivers/mmc/host/s3cmci.c new file +1337 -0

1,337 lines not on this page · raw message

drivers/mmc/host/s3cmci.h new file +71 -0

71 lines not on this page · raw message

drivers/mmc/host/Kconfig +11 -0
Index: linux-2.6.26-rc6-sdmmc/drivers/mmc/host/Kconfig
===================================================================
@@ -142,3 +142,14 @@ config MMC_SPI
 
 	  If unsure, or if your system has no SPI master driver, say N.
 
+config MMC_S3C
+	tristate "Samsung S3C SD/MMC Card Interface support"
+	depends on ARCH_S3C2410 && MMC
+	help
+	  This selects a driver for the MCI interface found in
+          Samsung's S3C2410, S3C2412, S3C2440, S3C2442 CPUs.
+	  If you have a board based on one of those and a MMC/SD
+	  slot, say Y or M here.
+
+	  If unsure, say N.
+
drivers/mmc/host/Makefile +1 -1
Index: linux-2.6.26-rc6-sdmmc/drivers/mmc/host/Makefile
===================================================================
@@ -18,4 +18,4 @@ obj-$(CONFIG_MMC_OMAP)		+= omap.o
 obj-$(CONFIG_MMC_AT91)		+= at91_mci.o
 obj-$(CONFIG_MMC_TIFM_SD)	+= tifm_sd.o
 obj-$(CONFIG_MMC_SPI)		+= mmc_spi.o
-
+obj-$(CONFIG_MMC_S3C)   	+= s3cmci.o
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#2 lore raw

PATCH v4 2/17 MMC: S3C24XX: Fix the checkpatch.pl errors in the s3cmci driver

In reply to Ben Dooks

Fix the checkpatch and other problems pointed out by akpm.

drivers/mmc/host/s3cmci.c +272 -266
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -11,15 +11,13 @@
 #include <linux/module.h>
 #include <linux/dma-mapping.h>
 #include <linux/clk.h>
-#include <linux/mmc/mmc.h>
 #include <linux/mmc/host.h>
 #include <linux/platform_device.h>
 #include <linux/irq.h>
+#include <linux/io.h>
 
 #include <asm/dma.h>
-#include <asm/dma-mapping.h>
 
-#include <asm/io.h>
 #include <asm/arch/regs-sdi.h>
 #include <asm/arch/regs-gpio.h>
 
@@ -43,13 +41,15 @@ static const int dbgmap_err   = dbg_err 
 static const int dbgmap_info  = dbg_info | dbg_conf;
 static const int dbgmap_debug = dbg_debug;
 
-#define dbg(host, channels, args...)		 \
-	if (dbgmap_err & channels) 		 \
-		dev_err(&host->pdev->dev, args); \
-	else if (dbgmap_info & channels)	 \
-		dev_info(&host->pdev->dev, args);\
-	else if (dbgmap_debug & channels)	 \
-		dev_dbg(&host->pdev->dev, args);
+#define dbg(host, channels, args...)		  \
+	do {					  \
+	if (dbgmap_err & channels) 		  \
+		dev_err(&host->pdev->dev, args);  \
+	else if (dbgmap_info & channels)	  \
+		dev_info(&host->pdev->dev, args); \
+	else if (dbgmap_debug & channels)	  \
+		dev_dbg(&host->pdev->dev, args);  \
+	} while (0)
 
 #define RESSIZE(ressource) (((ressource)->end - (ressource)->start)+1)
 
@@ -63,7 +63,7 @@ static void s3cmci_reset(struct s3cmci_h
 
 #ifdef CONFIG_MMC_DEBUG
 
-static inline void dbg_dumpregs(struct s3cmci_host *host, char *prefix)
+static void dbg_dumpregs(struct s3cmci_host *host, char *prefix)
 {
 	u32 con, pre, cmdarg, cmdcon, cmdsta, r0, r1, r2, r3, timer, bsize;
 	u32 datcon, datcnt, datsta, fsta, imask;
@@ -101,33 +101,33 @@ static inline void dbg_dumpregs(struct s
 }
 
 static void prepare_dbgmsg(struct s3cmci_host *host, struct mmc_command *cmd,
-								int stop)
+			   int stop)
 {
- 	snprintf(host->dbgmsg_cmd, 300,
-		"#%u%s op:%i arg:0x%08x flags:0x08%x retries:%u",
-		host->ccnt, (stop?" (STOP)":""),
-		cmd->opcode, cmd->arg, cmd->flags, cmd->retries);
+	snprintf(host->dbgmsg_cmd, 300,
+		 "#%u%s op:%i arg:0x%08x flags:0x08%x retries:%u",
+		 host->ccnt, (stop ? " (STOP)" : ""),
+		 cmd->opcode, cmd->arg, cmd->flags, cmd->retries);
 
 	if (cmd->data) {
 		snprintf(host->dbgmsg_dat, 300,
-			"#%u bsize:%u blocks:%u bytes:%u",
-			host->dcnt, cmd->data->blksz,
-			cmd->data->blocks,
-			cmd->data->blocks * cmd->data->blksz);
+			 "#%u bsize:%u blocks:%u bytes:%u",
+			 host->dcnt, cmd->data->blksz,
+			 cmd->data->blocks,
+			 cmd->data->blocks * cmd->data->blksz);
 	} else {
 		host->dbgmsg_dat[0] = '\0';
 	}
 }
 
 static void dbg_dumpcmd(struct s3cmci_host *host, struct mmc_command *cmd,
-								int fail)
+			int fail)
 {
-	unsigned int dbglvl = fail?dbg_fail:dbg_debug;
+	unsigned int dbglvl = fail ? dbg_fail : dbg_debug;
 
 	if (!cmd)
 		return;
 
-	if (cmd->error == MMC_ERR_NONE) {
+	if (cmd->error == 0) {
 		dbg(host, dbglvl, "CMD[OK] %s R0:0x%08x\n",
 			host->dbgmsg_cmd, cmd->resp[0]);
 	} else {
@@ -138,7 +138,7 @@ static void dbg_dumpcmd(struct s3cmci_ho
 	if (!cmd->data)
 		return;
 
-	if (cmd->data->error == MMC_ERR_NONE) {
+	if (cmd->data->error == 0) {
 		dbg(host, dbglvl, "DAT[OK] %s\n", host->dbgmsg_dat);
 	} else {
 		dbg(host, dbglvl, "DAT[ERR %i] %s DCNT:0x%08x\n",
@@ -146,14 +146,23 @@ static void dbg_dumpcmd(struct s3cmci_ho
 			readl(host->base + S3C2410_SDIDCNT));
 	}
 }
-#endif
+#else
+static void dbg_dumpcmd(struct s3cmci_host *host,
+			struct mmc_command *cmd, int fail) { }
+
+static void prepare_dbgmsg(struct s3cmci_host *host, struct mmc_command *cmd,
+			   int stop) { }
+
+static void dbg_dumpregs(struct s3cmci_host *host, char *prefix) { }
+
+#endif /* CONFIG_MMC_DEBUG */
 
 static inline u32 enable_imask(struct s3cmci_host *host, u32 imask)
 {
 	u32 newmask;
 
 	newmask = readl(host->base + host->sdiimsk);
-	newmask|= imask;
+	newmask |= imask;
 
 	writel(newmask, host->base + host->sdiimsk);
 
@@ -165,7 +174,7 @@ static inline u32 disable_imask(struct s
 	u32 newmask;
 
 	newmask = readl(host->base + host->sdiimsk);
-	newmask&= ~imask;
+	newmask &= ~imask;
 
 	writel(newmask, host->base + host->sdiimsk);
 
@@ -178,7 +187,7 @@ static inline void clear_imask(struct s3
 }
 
 static inline int get_data_buffer(struct s3cmci_host *host,
-			volatile u32 *words, volatile u32 **pointer)
+				  u32 *words, u32 **pointer)
 {
 	struct scatterlist *sg;
 
@@ -195,69 +204,82 @@ static inline int get_data_buffer(struct
 	}
 	sg = &host->mrq->data->sg[host->pio_sgptr];
 
-	*words	= sg->length >> 2;
-	*pointer= page_address(sg->page) + sg->offset;
+	*words = sg->length >> 2;
+	*pointer = sg_virt(sg);
 
 	host->pio_sgptr++;
 
 	dbg(host, dbg_sg, "new buffer (%i/%i)\n",
-	      host->pio_sgptr, host->mrq->data->sg_len);
+	    host->pio_sgptr, host->mrq->data->sg_len);
 
 	return 0;
 }
 
-#define FIFO_FILL(host) ((readl(host->base + S3C2410_SDIFSTA) & S3C2410_SDIFSTA_COUNTMASK) >> 2)
-#define FIFO_FREE(host) ((63 - (readl(host->base + S3C2410_SDIFSTA) & S3C2410_SDIFSTA_COUNTMASK)) >> 2)
+static inline u32 fifo_count(struct s3cmci_host *host)
+{
+	u32 fifostat = readl(host->base + S3C2410_SDIFSTA);
+
+	fifostat &= S3C2410_SDIFSTA_COUNTMASK;
+	return fifostat >> 2;
+}
+
+static inline u32 fifo_free(struct s3cmci_host *host)
+{
+	u32 fifostat = readl(host->base + S3C2410_SDIFSTA);
+
+	fifostat &= S3C2410_SDIFSTA_COUNTMASK;
+	return (63 - fifostat) >> 2;
+}
 
-static inline void do_pio_read(struct s3cmci_host *host)
+static void do_pio_read(struct s3cmci_host *host)
 {
 	int res;
 	u32 fifo;
 	void __iomem *from_ptr;
 
-	//write real prescaler to host, it might be set slow to fix
+	/* write real prescaler to host, it might be set slow to fix */
 	writel(host->prescaler, host->base + S3C2410_SDIPRE);
 
 	from_ptr = host->base + host->sdidata;
 
-	while ((fifo = FIFO_FILL(host))) {
+	while ((fifo = fifo_count(host))) {
 		if (!host->pio_words) {
 			res = get_data_buffer(host, &host->pio_words,
-							&host->pio_ptr);
+					      &host->pio_ptr);
 			if (res) {
 				host->pio_active = XFER_NONE;
 				host->complete_what = COMPLETION_FINALIZE;
 
 				dbg(host, dbg_pio, "pio_read(): "
-					"complete (no more data).\n");
+				    "complete (no more data).\n");
 				return;
 			}
 
-			dbg(host, dbg_pio, "pio_read(): new target: [%i]@[%p]\n",
-			       host->pio_words, host->pio_ptr);
+			dbg(host, dbg_pio,
+			    "pio_read(): new target: [%i]@[%p]\n",
+			    host->pio_words, host->pio_ptr);
 		}
 
-		dbg(host, dbg_pio, "pio_read(): fifo:[%02i] "
-				   "buffer:[%03i] dcnt:[%08X]\n",
-				   fifo, host->pio_words,
-				   readl(host->base + S3C2410_SDIDCNT));
+		dbg(host, dbg_pio,
+		    "pio_read(): fifo:[%02i] buffer:[%03i] dcnt:[%08X]\n",
+		    fifo, host->pio_words,
+		    readl(host->base + S3C2410_SDIDCNT));
 
 		if (fifo > host->pio_words)
 			fifo = host->pio_words;
 
-		host->pio_words-= fifo;
-		host->pio_count+= fifo;
+		host->pio_words -= fifo;
+		host->pio_count += fifo;
 
-		while(fifo--) {
+		while (fifo--)
 			*(host->pio_ptr++) = readl(from_ptr);
-		}
 	}
 
 	if (!host->pio_words) {
 		res = get_data_buffer(host, &host->pio_words, &host->pio_ptr);
 		if (res) {
-			dbg(host, dbg_pio, "pio_read(): "
-				"complete (no more buffers).\n");
+			dbg(host, dbg_pio,
+			    "pio_read(): complete (no more buffers).\n");
 			host->pio_active = XFER_NONE;
 			host->complete_what = COMPLETION_FINALIZE;
 
@@ -265,45 +287,44 @@ static inline void do_pio_read(struct s3
 		}
 	}
 
-	enable_imask(host, S3C2410_SDIIMSK_RXFIFOHALF | S3C2410_SDIIMSK_RXFIFOLAST);
+	enable_imask(host,
+		     S3C2410_SDIIMSK_RXFIFOHALF | S3C2410_SDIIMSK_RXFIFOLAST);
 }
 
-static inline void do_pio_write(struct s3cmci_host *host)
+static void do_pio_write(struct s3cmci_host *host)
 {
+	void __iomem *to_ptr;
 	int res;
 	u32 fifo;
 
-	void __iomem *to_ptr;
-
 	to_ptr = host->base + host->sdidata;
 
-	while ((fifo = FIFO_FREE(host))) {
+	while ((fifo = fifo_free(host))) {
 		if (!host->pio_words) {
 			res = get_data_buffer(host, &host->pio_words,
 							&host->pio_ptr);
 			if (res) {
-				dbg(host, dbg_pio, "pio_write(): "
-					"complete (no more data).\n");
+				dbg(host, dbg_pio,
+				    "pio_write(): complete (no more data).\n");
 				host->pio_active = XFER_NONE;
 
 				return;
 			}
 
-			dbg(host, dbg_pio, "pio_write(): "
-				"new source: [%i]@[%p]\n",
-				host->pio_words, host->pio_ptr);
+			dbg(host, dbg_pio,
+			    "pio_write(): new source: [%i]@[%p]\n",
+			    host->pio_words, host->pio_ptr);
 
 		}
 
 		if (fifo > host->pio_words)
 			fifo = host->pio_words;
 
-		host->pio_words-= fifo;
-		host->pio_count+= fifo;
+		host->pio_words -= fifo;
+		host->pio_count += fifo;
 
-		while(fifo--) {
+		while (fifo--)
 			writel(*(host->pio_ptr++), to_ptr);
-		}
 	}
 
 	enable_imask(host, S3C2410_SDIIMSK_TXFIFOHALF);
@@ -324,11 +345,11 @@ static void pio_tasklet(unsigned long da
 		clear_imask(host);
 		if (host->pio_active != XFER_NONE) {
 			dbg(host, dbg_err, "unfinished %s "
-				"- pio_count:[%u] pio_words:[%u]\n",
-				(host->pio_active == XFER_READ)?"read":"write",
-				host->pio_count, host->pio_words);
+			    "- pio_count:[%u] pio_words:[%u]\n",
+			    (host->pio_active == XFER_READ) ? "read" : "write",
+			    host->pio_count, host->pio_words);
 
-			host->mrq->data->error = MMC_ERR_DMA;
+			host->mrq->data->error = -EINVAL;
 		}
 
 		disable_irq(host->irq);
@@ -340,7 +361,7 @@ static void pio_tasklet(unsigned long da
  * ISR for SDI Interface IRQ
  * Communication between driver and ISR works as follows:
  *   host->mrq 			points to current request
- *   host->complete_what	tells the ISR when the request is considered done
+ *   host->complete_what	Indicates when the request is considered done
  *     COMPLETION_CMDSENT	  when the command was sent
  *     COMPLETION_RSPFIN          when a response was received
  *     COMPLETION_XFERFINISH	  when the data transfer is finished
@@ -365,26 +386,24 @@ static void pio_tasklet(unsigned long da
 
 static irqreturn_t s3cmci_irq(int irq, void *dev_id)
 {
-	struct s3cmci_host *host;
+	struct s3cmci_host *host = dev_id;
 	struct mmc_command *cmd;
 	u32 mci_csta, mci_dsta, mci_fsta, mci_dcnt, mci_imsk;
 	u32 mci_cclear, mci_dclear;
 	unsigned long iflags;
 
-	host = (struct s3cmci_host *)dev_id;
-
 	spin_lock_irqsave(&host->complete_lock, iflags);
 
-	mci_csta 	= readl(host->base + S3C2410_SDICMDSTAT);
-	mci_dsta 	= readl(host->base + S3C2410_SDIDSTA);
-	mci_dcnt 	= readl(host->base + S3C2410_SDIDCNT);
-	mci_fsta 	= readl(host->base + S3C2410_SDIFSTA);
-	mci_imsk	= readl(host->base + host->sdiimsk);
-	mci_cclear	= 0;
-	mci_dclear	= 0;
+	mci_csta = readl(host->base + S3C2410_SDICMDSTAT);
+	mci_dsta = readl(host->base + S3C2410_SDIDSTA);
+	mci_dcnt = readl(host->base + S3C2410_SDIDCNT);
+	mci_fsta = readl(host->base + S3C2410_SDIFSTA);
+	mci_imsk = readl(host->base + host->sdiimsk);
+	mci_cclear = 0;
+	mci_dclear = 0;
 
 	if ((host->complete_what == COMPLETION_NONE) ||
-			(host->complete_what == COMPLETION_FINALIZE)) {
+	    (host->complete_what == COMPLETION_FINALIZE)) {
 		host->status = "nothing to complete";
 		clear_imask(host);
 		goto irq_out;
@@ -396,7 +415,7 @@ static irqreturn_t s3cmci_irq(int irq, v
 		goto irq_out;
 	}
 
-	cmd = host->cmd_is_stop?host->mrq->stop:host->mrq->cmd;
+	cmd = host->cmd_is_stop ? host->mrq->stop : host->mrq->cmd;
 
 	if (!cmd) {
 		host->status = "no active cmd";
@@ -406,7 +425,7 @@ static irqreturn_t s3cmci_irq(int irq, v
 
 	if (!host->dodma) {
 		if ((host->pio_active == XFER_WRITE) &&
-				(mci_fsta & S3C2410_SDIFSTA_TFDET)) {
+		    (mci_fsta & S3C2410_SDIFSTA_TFDET)) {
 
 			disable_imask(host, S3C2410_SDIIMSK_TXFIFOHALF);
 			tasklet_schedule(&host->pio_tasklet);
@@ -414,10 +433,11 @@ static irqreturn_t s3cmci_irq(int irq, v
 		}
 
 		if ((host->pio_active == XFER_READ) &&
-				(mci_fsta & S3C2410_SDIFSTA_RFDET)) {
+		    (mci_fsta & S3C2410_SDIFSTA_RFDET)) {
 
 			disable_imask(host,
-				S3C2410_SDIIMSK_RXFIFOHALF | S3C2410_SDIIMSK_RXFIFOLAST);
+				      S3C2410_SDIIMSK_RXFIFOHALF |
+				      S3C2410_SDIIMSK_RXFIFOLAST);
 
 			tasklet_schedule(&host->pio_tasklet);
 			host->status = "pio rx";
@@ -425,7 +445,7 @@ static irqreturn_t s3cmci_irq(int irq, v
 	}
 
 	if (mci_csta & S3C2410_SDICMDSTAT_CMDTIMEOUT) {
-		cmd->error = MMC_ERR_TIMEOUT;
+		cmd->error = -ETIMEDOUT;
 		host->status = "error: command timeout";
 		goto fail_transfer;
 	}
@@ -441,7 +461,7 @@ static irqreturn_t s3cmci_irq(int irq, v
 
 	if (mci_csta & S3C2410_SDICMDSTAT_CRCFAIL) {
 		if (cmd->flags & MMC_RSP_CRC) {
-			cmd->error = MMC_ERR_BADCRC;
+			cmd->error = -EILSEQ;
 			host->status = "error: bad command crc";
 			goto fail_transfer;
 		}
@@ -470,32 +490,32 @@ static irqreturn_t s3cmci_irq(int irq, v
 	/* Check for FIFO failure */
 	if (host->is2440) {
 		if (mci_fsta & S3C2440_SDIFSTA_FIFOFAIL) {
-			host->mrq->data->error = MMC_ERR_FIFO;
+			host->mrq->data->error = -EILSEQ;
 			host->status = "error: 2440 fifo failure";
 			goto fail_transfer;
 		}
 	} else {
 		if (mci_dsta & S3C2410_SDIDSTA_FIFOFAIL) {
-			cmd->data->error = MMC_ERR_FIFO;
+			cmd->data->error = -EILSEQ;
 			host->status = "error:  fifo failure";
 			goto fail_transfer;
 		}
 	}
 
 	if (mci_dsta & S3C2410_SDIDSTA_RXCRCFAIL) {
-		cmd->data->error = MMC_ERR_BADCRC;
+		cmd->data->error = -EILSEQ;
 		host->status = "error: bad data crc (outgoing)";
 		goto fail_transfer;
 	}
 
 	if (mci_dsta & S3C2410_SDIDSTA_CRCFAIL) {
-		cmd->data->error = MMC_ERR_BADCRC;
+		cmd->data->error = -EILSEQ;
 		host->status = "error: bad data crc (incoming)";
 		goto fail_transfer;
 	}
 
 	if (mci_dsta & S3C2410_SDIDSTA_DATATIMEOUT) {
-		cmd->data->error = MMC_ERR_TIMEOUT;
+		cmd->data->error = -ETIMEDOUT;
 		host->status = "error: data timeout";
 		goto fail_transfer;
 	}
@@ -506,9 +526,8 @@ static irqreturn_t s3cmci_irq(int irq, v
 			goto close_transfer;
 		}
 
-		if (host->complete_what == COMPLETION_XFERFINISH_RSPFIN) {
+		if (host->complete_what == COMPLETION_XFERFINISH_RSPFIN)
 			host->complete_what = COMPLETION_RSPFIN;
-		}
 
 		mci_dclear |= S3C2410_SDIDSTA_XFERFINISH;
 	}
@@ -531,10 +550,9 @@ close_transfer:
 	goto irq_out;
 
 irq_out:
-	dbg(host, dbg_irq, "csta:0x%08x dsta:0x%08x "
-			   "fsta:0x%08x dcnt:0x%08x status:%s.\n",
-				mci_csta, mci_dsta, mci_fsta,
-				mci_dcnt, host->status);
+	dbg(host, dbg_irq,
+	    "csta:0x%08x dsta:0x%08x fsta:0x%08x dcnt:0x%08x status:%s.\n",
+	    mci_csta, mci_dsta, mci_fsta, mci_dcnt, host->status);
 
 	spin_unlock_irqrestore(&host->complete_lock, iflags);
 	return IRQ_HANDLED;
@@ -557,22 +575,20 @@ static irqreturn_t s3cmci_irq_cd(int irq
 }
 
 void s3cmci_dma_done_callback(struct s3c2410_dma_chan *dma_ch, void *buf_id,
-	int size, enum s3c2410_dma_buffresult result)
+			      int size, enum s3c2410_dma_buffresult result)
 {
+	struct s3cmci_host *host = buf_id;
 	unsigned long iflags;
 	u32 mci_csta, mci_dsta, mci_fsta, mci_dcnt;
-	struct s3cmci_host *host = (struct s3cmci_host *)buf_id;
 
-	mci_csta 	= readl(host->base + S3C2410_SDICMDSTAT);
-	mci_dsta 	= readl(host->base + S3C2410_SDIDSTA);
-	mci_fsta 	= readl(host->base + S3C2410_SDIFSTA);
-	mci_dcnt 	= readl(host->base + S3C2410_SDIDCNT);
-
-	if ((!host->mrq) || (!host->mrq) || (!host->mrq->data))
-		return;
-
-	if (!host->dmatogo)
-		return;
+	mci_csta = readl(host->base + S3C2410_SDICMDSTAT);
+	mci_dsta = readl(host->base + S3C2410_SDIDSTA);
+	mci_fsta = readl(host->base + S3C2410_SDIFSTA);
+	mci_dcnt = readl(host->base + S3C2410_SDIDCNT);
+
+	BUG_ON(!host->mrq);
+	BUG_ON(!host->mrq->data);
+	BUG_ON(!host->dmatogo);
 
 	spin_lock_irqsave(&host->complete_lock, iflags);
 
@@ -606,7 +622,7 @@ out:
 
 
 fail_request:
-	host->mrq->data->error = MMC_ERR_DMA;
+	host->mrq->data->error = -EINVAL;
 	host->complete_what = COMPLETION_FINALIZE;
 	writel(0, host->base + host->sdiimsk);
 	goto out;
@@ -616,7 +632,7 @@ fail_request:
 static void finalize_request(struct s3cmci_host *host)
 {
 	struct mmc_request *mrq = host->mrq;
-	struct mmc_command *cmd = host->cmd_is_stop?mrq->stop:mrq->cmd;
+	struct mmc_command *cmd = host->cmd_is_stop ? mrq->stop : mrq->cmd;
 	int debug_as_failure = 0;
 
 	if (host->complete_what != COMPLETION_FINALIZE)
@@ -625,22 +641,20 @@ static void finalize_request(struct s3cm
 	if (!mrq)
 		return;
 
-	if (cmd->data && (cmd->error == MMC_ERR_NONE) &&
-		  (cmd->data->error == MMC_ERR_NONE)) {
-
+	if (cmd->data && (cmd->error == 0) &&
+	    (cmd->data->error == 0)) {
 		if (host->dodma && (!host->dma_complete)) {
 			dbg(host, dbg_dma, "DMA Missing!\n");
 			return;
 		}
 	}
 
-	// Read response
+	/* Read response from controller. */
 	cmd->resp[0] = readl(host->base + S3C2410_SDIRSP0);
 	cmd->resp[1] = readl(host->base + S3C2410_SDIRSP1);
 	cmd->resp[2] = readl(host->base + S3C2410_SDIRSP2);
 	cmd->resp[3] = readl(host->base + S3C2410_SDIRSP3);
 
-	// reset clock speed, as it could still be set low for
 	writel(host->prescaler, host->base + S3C2410_SDIPRE);
 
 	if (cmd->error)
@@ -649,12 +663,9 @@ static void finalize_request(struct s3cm
 	if (cmd->data && cmd->data->error)
 		debug_as_failure = 1;
 
-	//if(cmd->flags & MMC_RSP_MAYFAIL) debug_as_failure = 0;
-
-#ifdef CONFIG_MMC_DEBUG
 	dbg_dumpcmd(host, cmd, debug_as_failure);
-#endif
-	//Cleanup controller
+
+	/* Cleanup controller */
 	writel(0, host->base + S3C2410_SDICMDARG);
 	writel(0, host->base + S3C2410_SDIDCON);
 	writel(0, host->base + S3C2410_SDICMDCON);
@@ -669,36 +680,35 @@ static void finalize_request(struct s3cm
 		return;
 	}
 
-	// If we have no data transfer we are finished here
+	/* If we have no data transfer we are finished here */
 	if (!mrq->data)
 		goto request_done;
 
-	// Calulate the amout of bytes transfer, but only if there was
-	// no error
-	if (mrq->data->error == MMC_ERR_NONE) {
+	/* Calulate the amout of bytes transfer if there was no error */
+	if (mrq->data->error == 0) {
 		mrq->data->bytes_xfered =
 			(mrq->data->blocks * mrq->data->blksz);
 	} else {
 		mrq->data->bytes_xfered = 0;
 	}
 
-	// If we had an error while transfering data we flush the
-	// DMA channel and the fifo to clear out any garbage
-	if (mrq->data->error != MMC_ERR_NONE) {
+	/* If we had an error while transfering data we flush the
+	 * DMA channel and the fifo to clear out any garbage. */
+	if (mrq->data->error != 0) {
 		if (host->dodma)
 			s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_FLUSH);
 
 		if (host->is2440) {
-			//Clear failure register and reset fifo
+			/* Clear failure register and reset fifo. */
 			writel(S3C2440_SDIFSTA_FIFORESET |
 			       S3C2440_SDIFSTA_FIFOFAIL,
 			       host->base + S3C2410_SDIFSTA);
 		} else {
 			u32 mci_con;
 
-			//reset fifo
+			/* reset fifo */
 			mci_con = readl(host->base + S3C2410_SDICON);
-			mci_con|= S3C2410_SDICON_FIFORESET;
+			mci_con |= S3C2410_SDICON_FIFORESET;
 
 			writel(mci_con, host->base + S3C2410_SDICON);
 		}
@@ -713,8 +723,8 @@ request_done:
 
 void s3cmci_dma_setup(struct s3cmci_host *host, enum s3c2410_dmasrc source)
 {
-	static int setup_ok = 0;
 	static enum s3c2410_dmasrc last_source = -1;
+	static int setup_ok;
 
 	if (last_source == source)
 		return;
@@ -722,12 +732,13 @@ void s3cmci_dma_setup(struct s3cmci_host
 	last_source = source;
 
 	s3c2410_dma_devconfig(host->dma, source, 3,
-		host->mem->start + host->sdidata);
+			      host->mem->start + host->sdidata);
 
 	if (!setup_ok) {
 		s3c2410_dma_config(host->dma, 4,
 			(S3C2410_DCON_HWTRIG | S3C2410_DCON_CH0_SDI));
-		s3c2410_dma_set_buffdone_fn(host->dma, s3cmci_dma_done_callback);
+		s3c2410_dma_set_buffdone_fn(host->dma,
+					    s3cmci_dma_done_callback);
 		s3c2410_dma_setflags(host->dma, S3C2410_DMAF_AUTOSTART);
 		setup_ok = 1;
 	}
@@ -744,31 +755,30 @@ static void s3cmci_send_command(struct s
 
 	enable_imask(host, imsk);
 
-	if (cmd->data) {
+	if (cmd->data)
 		host->complete_what = COMPLETION_XFERFINISH_RSPFIN;
-	} else if (cmd->flags & MMC_RSP_PRESENT) {
+	else if (cmd->flags & MMC_RSP_PRESENT)
 		host->complete_what = COMPLETION_RSPFIN;
-	} else {
+	else
 		host->complete_what = COMPLETION_CMDSENT;
-	}
 
 	writel(cmd->arg, host->base + S3C2410_SDICMDARG);
 
-	ccon = cmd->opcode & S3C2410_SDICMDCON_INDEX;
-	ccon|= S3C2410_SDICMDCON_SENDERHOST | S3C2410_SDICMDCON_CMDSTART;
+	ccon  = cmd->opcode & S3C2410_SDICMDCON_INDEX;
+	ccon |= S3C2410_SDICMDCON_SENDERHOST | S3C2410_SDICMDCON_CMDSTART;
 
 	if (cmd->flags & MMC_RSP_PRESENT)
 		ccon |= S3C2410_SDICMDCON_WAITRSP;
 
 	if (cmd->flags & MMC_RSP_136)
-		ccon|= S3C2410_SDICMDCON_LONGRSP;
+		ccon |= S3C2410_SDICMDCON_LONGRSP;
 
 	writel(ccon, host->base + S3C2410_SDICMDCON);
 }
 
 static int s3cmci_setup_data(struct s3cmci_host *host, struct mmc_data *data)
 {
-	u32 dcon, imsk, stoptries=3;
+	u32 dcon, imsk, stoptries = 3;
 
 	/* write DCON register */
 
@@ -777,37 +787,31 @@ static int s3cmci_setup_data(struct s3cm
 		return 0;
 	}
 
-	while(readl(host->base + S3C2410_SDIDSTA) &
-		(S3C2410_SDIDSTA_TXDATAON | S3C2410_SDIDSTA_RXDATAON)) {
+	while (readl(host->base + S3C2410_SDIDSTA) &
+	       (S3C2410_SDIDSTA_TXDATAON | S3C2410_SDIDSTA_RXDATAON)) {
 
 		dbg(host, dbg_err,
-			"mci_setup_data() transfer stillin progress.\n");
+		    "mci_setup_data() transfer stillin progress.\n");
 
 		writel(0, host->base + S3C2410_SDIDCON);
 		s3cmci_reset(host);
 
-		if (0 == (stoptries--)) {
-#ifdef CONFIG_MMC_DEBUG
+		if ((stoptries--) == 0) {
 			dbg_dumpregs(host, "DRF");
-#endif
-
 			return -EINVAL;
 		}
 	}
 
 	dcon  = data->blocks & S3C2410_SDIDCON_BLKNUM_MASK;
 
-	if (host->dodma) {
+	if (host->dodma)
 		dcon |= S3C2410_SDIDCON_DMAEN;
-	}
 
-	if (host->bus_width == MMC_BUS_WIDTH_4) {
+	if (host->bus_width == MMC_BUS_WIDTH_4)
 		dcon |= S3C2410_SDIDCON_WIDEBUS;
-	}
 
-	if (!(data->flags & MMC_DATA_STREAM)) {
+	if (!(data->flags & MMC_DATA_STREAM))
 		dcon |= S3C2410_SDIDCON_BLOCKMODE;
-	}
 
 	if (data->flags & MMC_DATA_WRITE) {
 		dcon |= S3C2410_SDIDCON_TXAFTERRESP;
@@ -831,8 +835,8 @@ static int s3cmci_setup_data(struct s3cm
 	writel(data->blksz, host->base + S3C2410_SDIBSIZE);
 
 	/* add to IMASK register */
-	imsk =	S3C2410_SDIIMSK_FIFOFAIL | S3C2410_SDIIMSK_DATACRC |
-		S3C2410_SDIIMSK_DATATIMEOUT | S3C2410_SDIIMSK_DATAFINISH;
+	imsk = S3C2410_SDIIMSK_FIFOFAIL | S3C2410_SDIIMSK_DATACRC |
+	       S3C2410_SDIIMSK_DATATIMEOUT | S3C2410_SDIIMSK_DATAFINISH;
 
 	enable_imask(host, imsk);
 
@@ -843,35 +847,33 @@ static int s3cmci_setup_data(struct s3cm
 	} else {
 		writel(0x0000FFFF, host->base + S3C2410_SDITIMER);
 
-		//FIX: set slow clock to prevent timeouts on read
-		if (data->flags & MMC_DATA_READ) {
+		/* FIX: set slow clock to prevent timeouts on read */
+		if (data->flags & MMC_DATA_READ)
 			writel(0xFF, host->base + S3C2410_SDIPRE);
-		}
 	}
 
-	//debug_dump_registers(host, "Data setup:");
-
 	return 0;
 }
 
+#define BOTH_DIR (MMC_DATA_WRITE | MMC_DATA_READ)
+
 static int s3cmci_prepare_pio(struct s3cmci_host *host, struct mmc_data *data)
 {
-	int rw = (data->flags & MMC_DATA_WRITE)?1:0;
+	int rw = (data->flags & MMC_DATA_WRITE) ? 1 : 0;
 
-	if (rw != ((data->flags & MMC_DATA_READ)?0:1))
-		return -EINVAL;
+	BUG_ON((data->flags & BOTH_DIR) == BOTH_DIR);
 
 	host->pio_sgptr = 0;
 	host->pio_words = 0;
 	host->pio_count = 0;
-	host->pio_active = rw?XFER_WRITE:XFER_READ;
+	host->pio_active = rw ? XFER_WRITE : XFER_READ;
 
 	if (rw) {
 		do_pio_write(host);
 		enable_imask(host, S3C2410_SDIIMSK_TXFIFOHALF);
 	} else {
 		enable_imask(host, S3C2410_SDIIMSK_RXFIFOHALF
-			| S3C2410_SDIIMSK_RXFIFOLAST);
+			     | S3C2410_SDIIMSK_RXFIFOLAST);
 	}
 
 	return 0;
@@ -880,18 +882,15 @@ static int s3cmci_prepare_pio(struct s3c
 static int s3cmci_prepare_dma(struct s3cmci_host *host, struct mmc_data *data)
 {
 	int dma_len, i;
+	int rw = (data->flags & MMC_DATA_WRITE) ? 1 : 0;
 
-	int rw = (data->flags & MMC_DATA_WRITE)?1:0;
-
-	if (rw != ((data->flags & MMC_DATA_READ)?0:1))
-		return -EINVAL;
+	BUG_ON((data->flags & BOTH_DIR) == BOTH_DIR);
 
-	s3cmci_dma_setup(host, rw?S3C2410_DMASRC_MEM:S3C2410_DMASRC_HW);
+	s3cmci_dma_setup(host, rw ? S3C2410_DMASRC_MEM : S3C2410_DMASRC_HW);
 	s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_FLUSH);
 
 	dma_len = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
-				(rw)?DMA_TO_DEVICE:DMA_FROM_DEVICE);
-
+			     (rw) ? DMA_TO_DEVICE : DMA_FROM_DEVICE);
 
 	if (dma_len == 0)
 		return -ENOMEM;
@@ -907,14 +906,14 @@ static int s3cmci_prepare_dma(struct s3c
 			sg_dma_len(&data->sg[i]));
 
 		res = s3c2410_dma_enqueue(host->dma, (void *) host,
-				sg_dma_address(&data->sg[i]),
-				sg_dma_len(&data->sg[i]));
+					  sg_dma_address(&data->sg[i]),
+					  sg_dma_len(&data->sg[i]));
 
 		if (res) {
 			s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_FLUSH);
 			return -EBUSY;
 		}
- 	}
+	}
 
 	s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_START);
 
@@ -925,60 +924,57 @@ static void s3cmci_send_request(struct m
 {
 	struct s3cmci_host *host = mmc_priv(mmc);
 	struct mmc_request *mrq = host->mrq;
-	struct mmc_command *cmd = host->cmd_is_stop?mrq->stop:mrq->cmd;
+	struct mmc_command *cmd = host->cmd_is_stop ? mrq->stop : mrq->cmd;
 
 	host->ccnt++;
-#ifdef CONFIG_MMC_DEBUG
 	prepare_dbgmsg(host, cmd, host->cmd_is_stop);
-#endif
-	//Clear command, data and fifo status registers
-	//Fifo clear only necessary on 2440, but doesn't hurt on 2410
+
+	/* Clear command, data and fifo status registers
+	   Fifo clear only necessary on 2440, but doesn't hurt on 2410
+	*/
 	writel(0xFFFFFFFF, host->base + S3C2410_SDICMDSTAT);
 	writel(0xFFFFFFFF, host->base + S3C2410_SDIDSTA);
 	writel(0xFFFFFFFF, host->base + S3C2410_SDIFSTA);
 
 	if (cmd->data) {
-		int res;
-		res = s3cmci_setup_data(host, cmd->data);
+		int res = s3cmci_setup_data(host, cmd->data);
 
 		host->dcnt++;
 
 		if (res) {
-			cmd->error = MMC_ERR_DMA;
-			cmd->data->error = MMC_ERR_DMA;
+			cmd->error = -EINVAL;
+			cmd->data->error = -EINVAL;
 
 			mmc_request_done(mmc, mrq);
 			return;
 		}
 
-
-		if (host->dodma) {
+		if (host->dodma)
 			res = s3cmci_prepare_dma(host, cmd->data);
-		} else {
+		else
 			res = s3cmci_prepare_pio(host, cmd->data);
-		}
 
 		if (res) {
-			cmd->error = MMC_ERR_DMA;
-			cmd->data->error = MMC_ERR_DMA;
+			cmd->error = res;
+			cmd->data->error = res;
 
 			mmc_request_done(mmc, mrq);
 			return;
 		}
-
 	}
 
-	// Send command
+	/* Send command */
 	s3cmci_send_command(host, cmd);
 
-	// Enable Interrupt
+	/* Enable Interrupt */
 	enable_irq(host->irq);
 }
 
 static void s3cmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
 {
- 	struct s3cmci_host *host = mmc_priv(mmc);
+	struct s3cmci_host *host = mmc_priv(mmc);
 
+	host->status = "mmc request";
 	host->cmd_is_stop = 0;
 	host->mrq = mrq;
 
@@ -990,62 +986,64 @@ static void s3cmci_set_ios(struct mmc_ho
 	struct s3cmci_host *host = mmc_priv(mmc);
 	u32 mci_psc, mci_con;
 
-	//Set power
-	mci_con = readl(host->base + S3C2410_SDICON);
-	switch(ios->power_mode) {
-		case MMC_POWER_ON:
-		case MMC_POWER_UP:
-			s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_SDCLK);
-			s3c2410_gpio_cfgpin(S3C2410_GPE6, S3C2410_GPE6_SDCMD);
-			s3c2410_gpio_cfgpin(S3C2410_GPE7, S3C2410_GPE7_SDDAT0);
-			s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1);
-			s3c2410_gpio_cfgpin(S3C2410_GPE9, S3C2410_GPE9_SDDAT2);
-			s3c2410_gpio_cfgpin(S3C2410_GPE10, S3C2410_GPE10_SDDAT3);
-
-			if (!host->is2440)
-				mci_con|=S3C2410_SDICON_FIFORESET;
+	/* Set the power state */
 
-			break;
+	mci_con = readl(host->base + S3C2410_SDICON);
 
-		case MMC_POWER_OFF:
-		default:
-			s3c2410_gpio_setpin(S3C2410_GPE5, 0);
-			s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_OUTP);
+	switch (ios->power_mode) {
+	case MMC_POWER_ON:
+	case MMC_POWER_UP:
+		s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_SDCLK);
+		s3c2410_gpio_cfgpin(S3C2410_GPE6, S3C2410_GPE6_SDCMD);
+		s3c2410_gpio_cfgpin(S3C2410_GPE7, S3C2410_GPE7_SDDAT0);
+		s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1);
+		s3c2410_gpio_cfgpin(S3C2410_GPE9, S3C2410_GPE9_SDDAT2);
+		s3c2410_gpio_cfgpin(S3C2410_GPE10, S3C2410_GPE10_SDDAT3);
+
+		if (!host->is2440)
+			mci_con |= S3C2410_SDICON_FIFORESET;
+
+		break;
+
+	case MMC_POWER_OFF:
+	default:
+		s3c2410_gpio_setpin(S3C2410_GPE5, 0);
+		s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_OUTP);
 
-			if (host->is2440)
-				mci_con|=S3C2440_SDICON_SDRESET;
+		if (host->is2440)
+			mci_con |= S3C2440_SDICON_SDRESET;
 
-			break;
+		break;
 	}
 
-	//Set clock
-	for (mci_psc=0; mci_psc<255; mci_psc++) {
+	/* Set clock */
+	for (mci_psc = 0; mci_psc < 255; mci_psc++) {
 		host->real_rate = host->clk_rate / (host->clk_div*(mci_psc+1));
 
 		if (host->real_rate <= ios->clock)
 			break;
 	}
 
-	if(mci_psc > 255) mci_psc = 255;
-	host->prescaler = mci_psc;
+	if (mci_psc > 255)
+		mci_psc = 255;
 
+	host->prescaler = mci_psc;
 	writel(host->prescaler, host->base + S3C2410_SDIPRE);
 
-	//If requested clock is 0, real_rate will be 0, too
+	/* If requested clock is 0, real_rate will be 0, too */
 	if (ios->clock == 0)
 		host->real_rate = 0;
 
-	//Set CLOCK_ENABLE
+	/* Set CLOCK_ENABLE */
 	if (ios->clock)
 		mci_con |= S3C2410_SDICON_CLOCKTYPE;
 	else
-		mci_con &=~S3C2410_SDICON_CLOCKTYPE;
+		mci_con &= ~S3C2410_SDICON_CLOCKTYPE;
 
 	writel(mci_con, host->base + S3C2410_SDICON);
 
-	if ((ios->power_mode==MMC_POWER_ON)
-		|| (ios->power_mode==MMC_POWER_UP)) {
-
+	if ((ios->power_mode == MMC_POWER_ON) ||
+	    (ios->power_mode == MMC_POWER_UP)) {
 		dbg(host, dbg_conf, "running at %lukHz (requested: %ukHz).\n",
 			host->real_rate/1000, ios->clock/1000);
 	} else {
@@ -1053,7 +1051,6 @@ static void s3cmci_set_ios(struct mmc_ho
 	}
 
 	host->bus_width = ios->bus_width;
-
 }
 
 static void s3cmci_reset(struct s3cmci_host *host)
@@ -1061,7 +1058,6 @@ static void s3cmci_reset(struct s3cmci_h
 	u32 con = readl(host->base + S3C2410_SDICON);
 
 	con |= S3C2440_SDICON_SDRESET;
-
 	writel(con, host->base + S3C2410_SDICON);
 }
 
@@ -1070,11 +1066,10 @@ static struct mmc_host_ops s3cmci_ops = 
 	.set_ios	= s3cmci_set_ios,
 };
 
-static int s3cmci_probe(struct platform_device *pdev, int is2440)
+static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440)
 {
-	struct mmc_host 	*mmc;
-	struct s3cmci_host 	*host;
-
+	struct s3cmci_host *host;
+	struct mmc_host	*mmc;
 	int ret;
 
 	mmc = mmc_alloc_host(sizeof(struct s3cmci_host), &pdev->dev);
@@ -1086,20 +1081,21 @@ static int s3cmci_probe(struct platform_
 	host = mmc_priv(mmc);
 	host->mmc 	= mmc;
 	host->pdev	= pdev;
+	host->is2440	= is2440;
 
 	spin_lock_init(&host->complete_lock);
 	tasklet_init(&host->pio_tasklet, pio_tasklet, (unsigned long) host);
+
 	if (is2440) {
-		host->is2440	= 1;
 		host->sdiimsk	= S3C2440_SDIIMSK;
 		host->sdidata	= S3C2440_SDIDATA;
 		host->clk_div	= 1;
 	} else {
-		host->is2440	= 0;
 		host->sdiimsk	= S3C2410_SDIIMSK;
 		host->sdidata	= S3C2410_SDIDATA;
 		host->clk_div	= 2;
 	}
+
 	host->dodma		= 0;
 	host->complete_what 	= COMPLETION_NONE;
 	host->pio_active 	= XFER_NONE;
@@ -1117,7 +1113,7 @@ static int s3cmci_probe(struct platform_
 	}
 
 	host->mem = request_mem_region(host->mem->start,
-		RESSIZE(host->mem), pdev->name);
+				       RESSIZE(host->mem), pdev->name);
 
 	if (!host->mem) {
 		dev_err(&pdev->dev, "failed to request io memory region.\n");
@@ -1145,6 +1141,10 @@ static int s3cmci_probe(struct platform_
 		goto probe_iounmap;
 	}
 
+	/* We get spurious interrupts even when we have set the IMSK
+	 * register to ignore everything, so use disable_irq() to make
+	 * ensure we don't lock the system with un-serviceable requests. */
+
 	disable_irq(host->irq);
 
 	s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_EINT2);
@@ -1153,7 +1153,6 @@ static int s3cmci_probe(struct platform_
 	if (request_irq(host->irq_cd, s3cmci_irq_cd, 0, DRIVER_NAME, host)) {
 		dev_err(&pdev->dev,
 			"failed to request card detect interrupt.\n");
-
 		ret = -ENOENT;
 		goto probe_free_irq;
 	}
@@ -1172,7 +1171,8 @@ static int s3cmci_probe(struct platform_
 		goto probe_free_host;
 	}
 
-	if ((ret = clk_enable(host->clk))) {
+	ret = clk_enable(host->clk);
+	if (ret) {
 		dev_err(&pdev->dev, "failed to enable clock source.\n");
 		goto clk_free;
 	}
@@ -1193,18 +1193,20 @@ static int s3cmci_probe(struct platform_
 	mmc->max_phys_segs	= 128;
 	mmc->max_hw_segs	= 128;
 
-	dbg(host, dbg_debug, "probe: mode:%s mapped mci_base:%p irq:%u irq_cd:%u dma:%u.\n",
-		(host->is2440?"2440":""),
-		host->base, host->irq, host->irq_cd, host->dma);
+	dbg(host, dbg_debug,
+	    "probe: mode:%s mapped mci_base:%p irq:%u irq_cd:%u dma:%u.\n",
+	    (host->is2440?"2440":""),
+	    host->base, host->irq, host->irq_cd, host->dma);
 
-	if ((ret = mmc_add_host(mmc))) {
+	ret = mmc_add_host(mmc);
+	if (ret) {
 		dev_err(&pdev->dev, "failed to add mmc host.\n");
 		goto free_dmabuf;
 	}
 
 	platform_set_drvdata(pdev, mmc);
+	dev_info(&pdev->dev, "initialisation done.\n");
 
-	dev_info(&pdev->dev,"initialisation done.\n");
 	return 0;
 
  free_dmabuf:
@@ -1214,10 +1216,10 @@ static int s3cmci_probe(struct platform_
 	clk_put(host->clk);
 
  probe_free_irq_cd:
- 	free_irq(host->irq_cd, host);
+	free_irq(host->irq_cd, host);
 
  probe_free_irq:
- 	free_irq(host->irq, host);
+	free_irq(host->irq, host);
 
  probe_iounmap:
 	iounmap(host->base);
@@ -1231,34 +1233,39 @@ static int s3cmci_probe(struct platform_
 	return ret;
 }
 
-static int s3cmci_remove(struct platform_device *pdev)
+static int __devexit s3cmci_remove(struct platform_device *pdev)
 {
-	struct mmc_host 	*mmc  = platform_get_drvdata(pdev);
-	struct s3cmci_host 	*host = mmc_priv(mmc);
+	struct mmc_host		*mmc  = platform_get_drvdata(pdev);
+	struct s3cmci_host	*host = mmc_priv(mmc);
 
 	mmc_remove_host(mmc);
+
 	clk_disable(host->clk);
 	clk_put(host->clk);
- 	free_irq(host->irq_cd, host);
- 	free_irq(host->irq, host);
+
+	tasklet_disable(&host->pio_tasklet);
+
+	free_irq(host->irq_cd, host);
+	free_irq(host->irq, host);
+
 	iounmap(host->base);
 	release_mem_region(host->mem->start, RESSIZE(host->mem));
-	mmc_free_host(mmc);
 
+	mmc_free_host(mmc);
 	return 0;
 }
 
-static int s3cmci_probe_2410(struct platform_device *dev)
+static int __devinit s3cmci_probe_2410(struct platform_device *dev)
 {
 	return s3cmci_probe(dev, 0);
 }
 
-static int s3cmci_probe_2412(struct platform_device *dev)
+static int __devinit s3cmci_probe_2412(struct platform_device *dev)
 {
 	return s3cmci_probe(dev, 1);
 }
 
-static int s3cmci_probe_2440(struct platform_device *dev)
+static int __devinit s3cmci_probe_2440(struct platform_device *dev)
 {
 	return s3cmci_probe(dev, 1);
 }
@@ -1285,29 +1292,29 @@ static int s3cmci_resume(struct platform
 #endif /* CONFIG_PM */
 
 
-static struct platform_driver s3cmci_driver_2410 =
-{
+static struct platform_driver s3cmci_driver_2410 = {
 	.driver.name	= "s3c2410-sdi",
+	.driver.owner	= THIS_MODULE,
 	.probe		= s3cmci_probe_2410,
-	.remove		= s3cmci_remove,
+	.remove		= __devexit_p(s3cmci_remove),
 	.suspend	= s3cmci_suspend,
 	.resume		= s3cmci_resume,
 };
 
-static struct platform_driver s3cmci_driver_2412 =
-{
+static struct platform_driver s3cmci_driver_2412 = {
 	.driver.name	= "s3c2412-sdi",
+	.driver.owner	= THIS_MODULE,
 	.probe		= s3cmci_probe_2412,
-	.remove		= s3cmci_remove,
+	.remove		= __devexit_p(s3cmci_remove),
 	.suspend	= s3cmci_suspend,
 	.resume		= s3cmci_resume,
 };
 
-static struct platform_driver s3cmci_driver_2440 =
-{
+static struct platform_driver s3cmci_driver_2440 = {
 	.driver.name	= "s3c2440-sdi",
+	.driver.owner	= THIS_MODULE,
 	.probe		= s3cmci_probe_2440,
-	.remove		= s3cmci_remove,
+	.remove		= __devexit_p(s3cmci_remove),
 	.suspend	= s3cmci_suspend,
 	.resume		= s3cmci_resume,
 };
@@ -1332,6 +1339,5 @@ module_init(s3cmci_init);
 module_exit(s3cmci_exit);
 
 MODULE_DESCRIPTION("Samsung S3C MMC/SD Card Interface driver");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
 MODULE_AUTHOR("Thomas Kleffel <[email protected]>");
-
drivers/mmc/host/s3cmci.h +10 -12
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.h
===================================================================
@@ -8,7 +8,7 @@
  * published by the Free Software Foundation.
  */
 
-//FIXME: DMA Resource management ?!
+/* FIXME: DMA Resource management ?! */
 #define S3CMCI_DMA 0
 
 enum s3cmci_waitfor {
@@ -39,32 +39,30 @@ struct s3cmci_host {
 	unsigned		sdiimsk;
 	unsigned		sdidata;
 	int			dodma;
-
-	volatile int		dmatogo;
+	int			dmatogo;
 
 	struct mmc_request	*mrq;
 	int			cmd_is_stop;
 
 	spinlock_t		complete_lock;
-	volatile enum s3cmci_waitfor
-				complete_what;
+	enum s3cmci_waitfor	complete_what;
 
-	volatile int		dma_complete;
+	int			dma_complete;
 
-	volatile u32		pio_sgptr;
-	volatile u32		pio_words;
-	volatile u32		pio_count;
-	volatile u32		*pio_ptr;
+	u32			pio_sgptr;
+	u32			pio_words;
+	u32			pio_count;
+	u32			*pio_ptr;
 #define XFER_NONE 0
 #define XFER_READ 1
 #define XFER_WRITE 2
-	volatile u32		pio_active;
+	u32			pio_active;
 
 	int			bus_width;
 
 	char 			dbgmsg_cmd[301];
 	char 			dbgmsg_dat[301];
-	volatile char		*status;
+	char			*status;
 
 	unsigned int		ccnt, dcnt;
 	struct tasklet_struct	pio_tasklet;
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
#3 lore raw

Re: [patch v4 02/17] MMC: S3C24XX: Fix the checkpatch.pl errors in the s3cmci driver

Quoted 5 lines · On Mon, 30 Jun 2008 16:25:49 +0100 Ben Dooks <[email protected]> wrote:

Fix the checkpatch and other problems pointed out by akpm.

I prefer to have this one merged into 01 as you'll end up with a commit that you cannot compile otherwise. Besides, running checkpatch is something you do before submitting anyway, not as a separate cleanup. :)

Signature · 9 lines
     -- Pierre Ossman

  Linux kernel, MMC maintainer        http://www.kernel.org
  rdesktop, core developer          http://www.rdesktop.org

  WARNING: This correspondence is being monitored by the
  Swedish government. Make sure your server uses encryption
  for SMTP traffic and consider using PGP for end-to-end
  encryption.
author
#4 lore raw

Re: [patch v4 02/17] MMC: S3C24XX: Fix the checkpatch.pl errors in the s3cmci driver

Quoted 6 lines · Pierre Ossman
Quoted 3 lines · On Mon, 30 Jun 2008 16:25:49 +0100 Ben Dooks <[email protected]> wrote:

Fix the checkpatch and other problems pointed out by akpm.

Quoted 6 lines
Quoted 2 lines

I prefer to have this one merged into 01 as you'll end up with a commit that you cannot compile otherwise. Besides, running checkpatch is something you do before submitting anyway, not as a separate cleanup. :)

In this case I kept it seperate as the cleanups where done by myself as the original driver authour is not interested or too busy to do these himself. Basically, I was trying to keep the driver and my own cleanup work seperate.

Signature · 4 lines
Ben

Q:      What's a light-year?
A:      One-third less calories than a regular year.
#5 lore raw

Re: [patch v4 02/17] MMC: S3C24XX: Fix the checkpatch.pl errors in the s3cmci driver

Quoted 10 lines · Ben Dooks
Quoted 9 lines · Pierre Ossman
Quoted 5 lines · On Mon, 30 Jun 2008 16:25:49 +0100 Ben Dooks <[email protected]> wrote:

Fix the checkpatch and other problems pointed out by akpm.

Quoted 8 lines
Quoted 3 lines

I prefer to have this one merged into 01 as you'll end up with a commit that you cannot compile otherwise. Besides, running checkpatch is something you do before submitting anyway, not as a separate cleanup. :)

In this case I kept it seperate as the cleanups where done by myself as the original driver authour is not interested or too busy to do these himself. Basically, I was trying to keep the driver and my own cleanup work seperate.

don't worry about that. Thomas Kleffel is unlikely to return to do any active work on it (I know him personally), and the OpenMoko community will inevitably rebase its patches based on whatever ends up in mainline. So nobody is worried if you merge all that stuff into one patch. It's probably polite to add the significant contributors (such as yourself and myself) to the list of authors at the beginning of the file though - given the amount of changes the driver has received compared to Tomas' original.

Thanks for all your work,

Signature · 3 lines
- Harald Welte <[email protected]>          	        http://openmoko.org/
============================================================================
Software for the world's first truly open Free Software mobile phone
author
#6 lore raw

Re: [patch v4 02/17] MMC: S3C24XX: Fix the checkpatch.pl errors in the s3cmci driver

Quoted 20 lines · Harald Welte
Quoted 10 lines · Ben Dooks
Quoted 9 lines · Pierre Ossman
Quoted 5 lines · On Mon, 30 Jun 2008 16:25:49 +0100 Ben Dooks <[email protected]> wrote:

Fix the checkpatch and other problems pointed out by akpm.

Quoted 8 lines
Quoted 3 lines

I prefer to have this one merged into 01 as you'll end up with a commit that you cannot compile otherwise. Besides, running checkpatch is something you do before submitting anyway, not as a separate cleanup. :)

In this case I kept it seperate as the cleanups where done by myself as the original driver authour is not interested or too busy to do these himself. Basically, I was trying to keep the driver and my own cleanup work seperate.

Quoted 8 lines

don't worry about that. Thomas Kleffel is unlikely to return to do any active work on it (I know him personally), and the OpenMoko community will inevitably rebase its patches based on whatever ends up in mainline. So nobody is worried if you merge all that stuff into one patch. It's probably polite to add the significant contributors (such as yourself and myself) to the list of authors at the beginning of the file though - given the amount of changes the driver has received compared to Tomas' original.

Thanks, having an public discussion about the position of the original authour is useful. I was intending on submitting a patch once this lot is merged to add myself and select others to the driver after the fact so that everyone can acknowledge it.

You have missed part of the point. My extra work is not a small set of changes which won't get counted when profiling the Kernel contributors. My employers have given me time to sort these items out, and we do get work off the fact that we're shown to be in the leading contributors (iirc, 18th last-year) so I was trying to ensure that this wasn't lost.

If Pierre or Thomas has objections to either then the series can be reposted with #1 and #2 merged together.

Signature · 4 lines
Ben

Q:      What's a light-year?
A:      One-third less calories than a regular year.
#7 lore raw

Re: [patch v4 02/17] MMC: S3C24XX: Fix the checkpatch.pl errors in the s3cmci driver

Quoted 8 lines · On Mon, 30 Jun 2008 18:04:08 +0100 Ben Dooks <[email protected]> wrote:

You have missed part of the point. My extra work is not a small set of changes which won't get counted when profiling the Kernel contributors. My employers have given me time to sort these items out, and we do get work off the fact that we're shown to be in the leading contributors (iirc, 18th last-year) so I was trying to ensure that this wasn't lost.

I can appreciate that, but I do not want a commit in the tree that doesn't even compile. You don't have to merge in all the other ones (which should give you a reasonable blip in the statistics), but at least #1 and #2.

Signature · 9 lines
     -- Pierre Ossman

  Linux kernel, MMC maintainer        http://www.kernel.org
  rdesktop, core developer          http://www.rdesktop.org

  WARNING: This correspondence is being monitored by the
  Swedish government. Make sure your server uses encryption
  for SMTP traffic and consider using PGP for end-to-end
  encryption.
author
#8 lore raw

Re: [patch v4 02/17] MMC: S3C24XX: Fix the checkpatch.pl errors in the s3cmci driver

Quoted 12 lines · Pierre Ossman
Quoted 8 lines · On Mon, 30 Jun 2008 18:04:08 +0100 Ben Dooks <[email protected]> wrote:

You have missed part of the point. My extra work is not a small set of changes which won't get counted when profiling the Kernel contributors. My employers have given me time to sort these items out, and we do get work off the fact that we're shown to be in the leading contributors (iirc, 18th last-year) so I was trying to ensure that this wasn't lost.

Quoted 4 lines

I can appreciate that, but I do not want a commit in the tree that doesn't even compile. You don't have to merge in all the other ones (which should give you a reasonable blip in the statistics), but at least #1 and #2.

Ok, I'll sort out reposting this.

Signature · 4 lines
Ben

Q:      What's a light-year?
A:      One-third less calories than a regular year.
#9 lore raw

Re: [patch v4 02/17] MMC: S3C24XX: Fix the checkpatch.pl errors in the s3cmci driver

In reply to Harald Welte

Hi,

Quoted 9 lines

don't worry about that. Thomas Kleffel is unlikely to return to do any active work on it (I know him personally), and the OpenMoko community will inevitably rebase its patches based on whatever ends up in mainline. So nobody is worried if you merge all that stuff into one patch. It's probably polite to add the significant contributors (such as yourself and myself) to the list of authors at the beginning of the file though - given the amount of changes the driver has received compared to Tomas' original.

Harald is 100% right. I have absolutely no time at all to maintain this driver and I haven't worked on it (or any other SD/MMC related stuff) for almost two years now.

I'd like to thank Harald, Ben, Pierre and all others who are working hard to get the driver merged.

See you,

Thomas Kleffel

author
#10 lore raw

Re: [patch v4 02/17] MMC: S3C24XX: Fix the checkpatch.pl errors in the s3cmci driver

Quoted 10 lines · Thomas Kleffel

Hi,

Quoted 9 lines

don't worry about that. Thomas Kleffel is unlikely to return to do any active work on it (I know him personally), and the OpenMoko community will inevitably rebase its patches based on whatever ends up in mainline. So nobody is worried if you merge all that stuff into one patch. It's probably polite to add the significant contributors (such as yourself and myself) to the list of authors at the beginning of the file though - given the amount of changes the driver has received compared to Tomas' original.

Quoted 6 lines

Harald is 100% right. I have absolutely no time at all to maintain this driver and I haven't worked on it (or any other SD/MMC related stuff) for almost two years now.

I'd like to thank Harald, Ben, Pierre and all others who are working hard to get the driver merged.

Thanks for your original work. I suppose I should add a signed-off-by:
line from you to the original driver.

Quoted 3 lines

See you,

Thomas Kleffel

Signature · 4 lines
Ben

Q:      What's a light-year?
A:      One-third less calories than a regular year.
author
#11 lore raw

PATCH v4 3/17 MMC: S3C24XX MMC/SD driver write fixes

In reply to Ben Dooks

From: Harald Welte <[email protected]>

This patch is a workaround of some S3C2410 MMC chip bug

drivers/mmc/host/s3cmci.c +13 -3
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -461,9 +461,19 @@ static irqreturn_t s3cmci_irq(int irq, v
 
 	if (mci_csta & S3C2410_SDICMDSTAT_CRCFAIL) {
 		if (cmd->flags & MMC_RSP_CRC) {
-			cmd->error = -EILSEQ;
-			host->status = "error: bad command crc";
-			goto fail_transfer;
+			if (host->mrq->cmd->flags & MMC_RSP_136) {
+				dbg(host, dbg_irq,
+				    "fixup: ignore CRC fail with long rsp\n");
+			} else {
+				/* note, we used to fail the transfer
+				 * here, but it seems that this is just
+				 * the hardware getting it wrong.
+				 *
+				 * cmd->error = -EILSEQ;
+				 * host->status = "error: bad command crc";
+				 * goto fail_transfer;
+				*/
+			}
 		}
 
 		mci_cclear |= S3C2410_SDICMDSTAT_CRCFAIL;
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#12 lore raw

PATCH v4 4/17 MMC: DMA free fix for S3C24XX SD/MMC driver

In reply to Ben Dooks

From: Harald Welte <[email protected]>

Bugfix to ensure DMA channel allocated is freed on exit.

drivers/mmc/host/s3cmci.c +1 -0
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -1254,6 +1254,7 @@ static int s3cmci_remove(struct platform
 	clk_put(host->clk);
 
 	tasklet_disable(&host->pio_tasklet);
+	s3c2410_dma_free(S3CMCI_DMA, &s3cmci_dma_client);
 
 	free_irq(host->irq_cd, host);
 	free_irq(host->irq, host);
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#13 lore raw

PATCH v4 5/17 MMC: S3C24XX MMC/SD stop fix

In reply to Ben Dooks

From: Thomas Kleffel <[email protected]>

Fix the request finalisation by ensuring the controller is stopped.

drivers/mmc/host/s3cmci.c +2 -2
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -677,7 +677,7 @@ static void finalize_request(struct s3cm
 
 	/* Cleanup controller */
 	writel(0, host->base + S3C2410_SDICMDARG);
-	writel(0, host->base + S3C2410_SDIDCON);
+	writel(S3C2410_SDIDCON_STOP, host->base + S3C2410_SDIDCON);
 	writel(0, host->base + S3C2410_SDICMDCON);
 	writel(0, host->base + host->sdiimsk);
 
@@ -803,7 +803,7 @@ static int s3cmci_setup_data(struct s3cm
 		dbg(host, dbg_err,
 		    "mci_setup_data() transfer stillin progress.\n");
 
-		writel(0, host->base + S3C2410_SDIDCON);
+		writel(S3C2410_SDIDCON_STOP, host->base + S3C2410_SDIDCON);
 		s3cmci_reset(host);
 
 		if ((stoptries--) == 0) {
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#14 lore raw

PATCH v4 6/17 MMC: Fix S3C24XX IRQ enable during PIO transfers

In reply to Ben Dooks

From: Roman Moracik <[email protected]>

Fix Bug #677 - I/O errors on heavy microSD writes for 2.6.22.x.

drivers/mmc/host/s3cmci.c +4 -3
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -335,6 +335,8 @@ static void pio_tasklet(unsigned long da
 	struct s3cmci_host *host = (struct s3cmci_host *) data;
 
 
+	disable_irq(host->irq);
+
 	if (host->pio_active == XFER_WRITE)
 		do_pio_write(host);
 
@@ -352,9 +354,9 @@ static void pio_tasklet(unsigned long da
 			host->mrq->data->error = -EINVAL;
 		}
 
-		disable_irq(host->irq);
 		finalize_request(host);
-	}
+	} else
+		enable_irq(host->irq);
 }
 
 /*
@@ -630,7 +632,6 @@ out:
 	spin_unlock_irqrestore(&host->complete_lock, iflags);
 	return;
 
-
 fail_request:
 	host->mrq->data->error = -EINVAL;
 	host->complete_what = COMPLETION_FINALIZE;
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#15 lore raw

PATCH v4 7/17 MMC: S3C24XX: Add platform data for MMC/SD driver

In reply to Ben Dooks

This patch adds platform data support to the s3mci driver. This allows flexible board-specific configuration of set_power, card detect and read only pins.

drivers/mmc/host/s3cmci.c +41 -3
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -21,6 +21,8 @@
 #include <asm/arch/regs-sdi.h>
 #include <asm/arch/regs-gpio.h>
 
+#include <asm/plat-s3c24xx/mci.h>
+
 #include "s3cmci.h"
 
 #define DRIVER_NAME "s3c-mci"
@@ -1011,6 +1013,9 @@ static void s3cmci_set_ios(struct mmc_ho
 		s3c2410_gpio_cfgpin(S3C2410_GPE9, S3C2410_GPE9_SDDAT2);
 		s3c2410_gpio_cfgpin(S3C2410_GPE10, S3C2410_GPE10_SDDAT3);
 
+		if (host->pdata->set_power)
+			host->pdata->set_power(ios->power_mode, ios->vdd);
+
 		if (!host->is2440)
 			mci_con |= S3C2410_SDICON_FIFORESET;
 
@@ -1024,6 +1029,9 @@ static void s3cmci_set_ios(struct mmc_ho
 		if (host->is2440)
 			mci_con |= S3C2440_SDICON_SDRESET;
 
+		if (host->pdata->set_power)
+			host->pdata->set_power(ios->power_mode, ios->vdd);
+
 		break;
 	}
 
@@ -1072,9 +1080,25 @@ static void s3cmci_reset(struct s3cmci_h
 	writel(con, host->base + S3C2410_SDICON);
 }
 
+static int s3cmci_get_ro(struct mmc_host *mmc)
+{
+	struct s3cmci_host *host = mmc_priv(mmc);
+
+	if (host->pdata->gpio_wprotect == 0)
+		return 0;
+
+	return s3c2410_gpio_getpin(host->pdata->gpio_wprotect);
+}
+
 static struct mmc_host_ops s3cmci_ops = {
 	.request	= s3cmci_request,
 	.set_ios	= s3cmci_set_ios,
+	.get_ro		= s3cmci_get_ro,
+};
+
+static struct s3c24xx_mci_pdata s3cmci_def_pdata = {
+	/* This is currently here to avoid a number of if (host->pdata)
+	 * checks. Any zero fields to ensure reaonable defaults are picked. */
 };
 
 static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440)
@@ -1094,6 +1118,12 @@ static int __devinit s3cmci_probe(struct
 	host->pdev	= pdev;
 	host->is2440	= is2440;
 
+	host->pdata = pdev->dev.platform_data;
+	if (!host->pdata) {
+		pdev->dev.platform_data = &s3cmci_def_pdata;
+		host->pdata = &s3cmci_def_pdata;
+	}
+
 	spin_lock_init(&host->complete_lock);
 	tasklet_init(&host->pio_tasklet, pio_tasklet, (unsigned long) host);
 
@@ -1112,7 +1142,8 @@ static int __devinit s3cmci_probe(struct
 	host->pio_active 	= XFER_NONE;
 
 	host->dma		= S3CMCI_DMA;
-	host->irq_cd		= IRQ_EINT2;
+	host->irq_cd = s3c2410_gpio_getirq(host->pdata->gpio_detect);
+	s3c2410_gpio_cfgpin(host->pdata->gpio_detect, S3C2410_GPIO_IRQ);
 
 	host->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!host->mem) {
@@ -1158,7 +1189,7 @@ static int __devinit s3cmci_probe(struct
 
 	disable_irq(host->irq);
 
-	s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_EINT2);
+	s3c2410_gpio_cfgpin(host->pdata->gpio_detect, S3C2410_GPIO_IRQ);
 	set_irq_type(host->irq_cd, IRQT_BOTHEDGE);
 
 	if (request_irq(host->irq_cd, s3cmci_irq_cd, 0, DRIVER_NAME, host)) {
@@ -1168,6 +1199,10 @@ static int __devinit s3cmci_probe(struct
 		goto probe_free_irq;
 	}
 
+	if (host->pdata->gpio_wprotect)
+		s3c2410_gpio_cfgpin(host->pdata->gpio_wprotect,
+				    S3C2410_GPIO_INPUT);
+
 	if (s3c2410_dma_request(S3CMCI_DMA, &s3cmci_dma_client, NULL)) {
 		dev_err(&pdev->dev, "unable to get DMA channel.\n");
 		ret = -EBUSY;
@@ -1191,11 +1226,14 @@ static int __devinit s3cmci_probe(struct
 	host->clk_rate = clk_get_rate(host->clk);
 
 	mmc->ops 	= &s3cmci_ops;
-	mmc->ocr_avail	= MMC_VDD_32_33;
+	mmc->ocr_avail	= MMC_VDD_32_33 | MMC_VDD_33_34;
 	mmc->caps	= MMC_CAP_4_BIT_DATA;
 	mmc->f_min 	= host->clk_rate / (host->clk_div * 256);
 	mmc->f_max 	= host->clk_rate / host->clk_div;
 
+	if (host->pdata->ocr_avail)
+		mmc->ocr_avail = host->pdata->ocr_avail;
+
 	mmc->max_blk_count	= 4095;
 	mmc->max_blk_size	= 4095;
 	mmc->max_req_size	= 4095 * 512;
drivers/mmc/host/s3cmci.h +1 -0
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.h
===================================================================
@@ -22,6 +22,7 @@ enum s3cmci_waitfor {
 
 struct s3cmci_host {
 	struct platform_device	*pdev;
+	struct s3c24xx_mci_pdata *pdata;
 	struct mmc_host		*mmc;
 	struct resource		*mem;
 	struct clk		*clk;
include/asm-arm/plat-s3c24xx/mci.h new file +12 -0
Index: linux-2.6.26-rc8-next20080627/include/asm-arm/plat-s3c24xx/mci.h
===================================================================
@@ -0,0 +1,12 @@
+#ifndef _ARCH_MCI_H
+#define _ARCH_MCI_H
+
+struct s3c24xx_mci_pdata {
+	unsigned int	gpio_detect;
+	unsigned int	gpio_wprotect;
+	unsigned long	ocr_avail;
+	void		(*set_power)(unsigned char power_mode,
+				     unsigned short vdd);
+};
+
+#endif /* _ARCH_NCI_H */
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#16 lore raw

PATCH v4 8/17 MMC: S3C24XX: Add support to invert write protect line

In reply to Ben Dooks

Support for inverting the sense of the MMC driver's write protect detection line.

drivers/mmc/host/s3cmci.c +9 -2
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -1083,11 +1083,18 @@ static void s3cmci_reset(struct s3cmci_h
 static int s3cmci_get_ro(struct mmc_host *mmc)
 {
 	struct s3cmci_host *host = mmc_priv(mmc);
+	struct s3c24xx_mci_pdata *pdata = host->pdata;
+	int ret;
 
-	if (host->pdata->gpio_wprotect == 0)
+	if (pdata->gpio_wprotect == 0)
 		return 0;
 
-	return s3c2410_gpio_getpin(host->pdata->gpio_wprotect);
+	ret = s3c2410_gpio_getpin(pdata->gpio_wprotect);
+
+	if (pdata->wprotect_invert)
+		ret = !ret;
+
+	return ret;
 }
 
 static struct mmc_host_ops s3cmci_ops = {
include/asm-arm/plat-s3c24xx/mci.h +2 -0
Index: linux-2.6.26-rc8-next20080627/include/asm-arm/plat-s3c24xx/mci.h
===================================================================
@@ -2,6 +2,8 @@
 #define _ARCH_MCI_H
 
 struct s3c24xx_mci_pdata {
+	unsigned int	wprotect_invert : 1;
+
 	unsigned int	gpio_detect;
 	unsigned int	gpio_wprotect;
 	unsigned long	ocr_avail;
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#17 lore raw

PATCH v4 9/17 MMC: S3C24XX: Ensure host->mrq->data is valid

In reply to Ben Dooks

Fix a crash if host->mrq->data is NULL on ending a transfer.

drivers/mmc/host/s3cmci.c +2 -1
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -353,7 +353,8 @@ static void pio_tasklet(unsigned long da
 			    (host->pio_active == XFER_READ) ? "read" : "write",
 			    host->pio_count, host->pio_words);
 
-			host->mrq->data->error = -EINVAL;
+			if (host->mrq->data)
+				host->mrq->data->error = -EINVAL;
 		}
 
 		finalize_request(host);
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#18 lore raw

PATCH v4 10/17 MMC: S3C24XX: Allow card-detect on non-IRQ capable pin

In reply to Ben Dooks

Add support to the S3C24XX MMC driver to have the card detect be on a pin that is not IRQ capable.

drivers/mmc/host/s3cmci.c +17 -11
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -1150,8 +1150,6 @@ static int __devinit s3cmci_probe(struct
 	host->pio_active 	= XFER_NONE;
 
 	host->dma		= S3CMCI_DMA;
-	host->irq_cd = s3c2410_gpio_getirq(host->pdata->gpio_detect);
-	s3c2410_gpio_cfgpin(host->pdata->gpio_detect, S3C2410_GPIO_IRQ);
 
 	host->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!host->mem) {
@@ -1197,14 +1195,20 @@ static int __devinit s3cmci_probe(struct
 
 	disable_irq(host->irq);
 
-	s3c2410_gpio_cfgpin(host->pdata->gpio_detect, S3C2410_GPIO_IRQ);
-	set_irq_type(host->irq_cd, IRQT_BOTHEDGE);
+	host->irq_cd = s3c2410_gpio_getirq(host->pdata->gpio_detect);
 
-	if (request_irq(host->irq_cd, s3cmci_irq_cd, 0, DRIVER_NAME, host)) {
-		dev_err(&pdev->dev,
-			"failed to request card detect interrupt.\n");
-		ret = -ENOENT;
-		goto probe_free_irq;
+	if (host->irq_cd >= 0) {
+		if (request_irq(host->irq_cd, s3cmci_irq_cd,
+				IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+				DRIVER_NAME, host)) {
+			dev_err(&pdev->dev, "can't get card detect irq.\n");
+			ret = -ENOENT;
+			goto probe_free_irq;
+		}
+	} else {
+		dev_warn(&pdev->dev, "host detect has no irq available\n");
+		s3c2410_gpio_cfgpin(host->pdata->gpio_detect,
+				    S3C2410_GPIO_INPUT);
 	}
 
 	if (host->pdata->gpio_wprotect)
@@ -1273,7 +1277,8 @@ static int __devinit s3cmci_probe(struct
 	clk_put(host->clk);
 
  probe_free_irq_cd:
-	free_irq(host->irq_cd, host);
+	if (host->irq_cd >= 0)
+		free_irq(host->irq_cd, host);
 
  probe_free_irq:
 	free_irq(host->irq, host);
@@ -1303,7 +1308,8 @@ static int s3cmci_remove(struct platform
 	tasklet_disable(&host->pio_tasklet);
 	s3c2410_dma_free(S3CMCI_DMA, &s3cmci_dma_client);
 
-	free_irq(host->irq_cd, host);
+	if (host->irq_cd >= 0)
+		free_irq(host->irq_cd, host);
 	free_irq(host->irq, host);
 
 	iounmap(host->base);
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#19 lore raw

PATCH v4 11/17 MMC: S3C24XX: Fix s3c2410_dma_request() return code check.

In reply to Ben Dooks

The driver should be checking for a negative error code from s3c2410_dma_request(), not non-zero. Newer kernels now return the DMA channel number that was allocated by the request.

drivers/mmc/host/s3cmci.c +1 -1
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -1215,7 +1215,7 @@ static int __devinit s3cmci_probe(struct
 		s3c2410_gpio_cfgpin(host->pdata->gpio_wprotect,
 				    S3C2410_GPIO_INPUT);
 
-	if (s3c2410_dma_request(S3CMCI_DMA, &s3cmci_dma_client, NULL)) {
+	if (s3c2410_dma_request(S3CMCI_DMA, &s3cmci_dma_client, NULL) < 0) {
 		dev_err(&pdev->dev, "unable to get DMA channel.\n");
 		ret = -EBUSY;
 		goto probe_free_irq_cd;
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#20 lore raw

PATCH v4 12/17 MMC: S3C24XX: Add MODULE_ALIAS() entries for the platform devices

In reply to Ben Dooks

Add MODULE_ALIAS() declerations for all the supported platform devices for this driver.

drivers/mmc/host/s3cmci.c +3 -0
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -1405,3 +1405,6 @@ module_exit(s3cmci_exit);
 MODULE_DESCRIPTION("Samsung S3C MMC/SD Card Interface driver");
 MODULE_LICENSE("GPL v2");
 MODULE_AUTHOR("Thomas Kleffel <[email protected]>");
+MODULE_ALIAS("platform:s3c2410-sdi");
+MODULE_ALIAS("platform:s3c2412-sdi");
+MODULE_ALIAS("platform:s3c2440-sdi");
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#21 lore raw

PATCH v4 13/17 MMC: S3C24XX: Fix use of msecs where jiffies are needed

In reply to Ben Dooks

mmc_detect_change() takes jiffies, not msecs. Convert the previous value of msecs into jiffies before calling.

drivers/mmc/host/s3cmci.c +1 -1
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -584,7 +584,7 @@ static irqreturn_t s3cmci_irq_cd(int irq
 
 	dbg(host, dbg_irq, "card detect\n");
 
-	mmc_detect_change(host->mmc, 500);
+	mmc_detect_change(host->mmc, msecs_to_jiffies(500));
 
 	return IRQ_HANDLED;
 }
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#22 lore raw

PATCH v4 14/17 MMC: S3C24XX: Add media presence test to request handling.

In reply to Ben Dooks

Ensure that we have physical media present before attempting to send a request to a card. This ensures that we do not get flooded by errors from commands that can never be completed timing out.

drivers/mmc/host/s3cmci.c +18 -1
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -984,6 +984,18 @@ static void s3cmci_send_request(struct m
 	enable_irq(host->irq);
 }
 
+static int s3cmci_card_present(struct s3cmci_host *host)
+{
+	struct s3c24xx_mci_pdata *pdata = host->pdata;
+	int ret;
+
+	if (pdata->gpio_detect == 0)
+		return -ENOSYS;
+
+	ret = s3c2410_gpio_getpin(pdata->gpio_detect) ? 0 : 1;
+	return ret ^ pdata->detect_invert;
+}
+
 static void s3cmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
 {
 	struct s3cmci_host *host = mmc_priv(mmc);
@@ -992,7 +1004,12 @@ static void s3cmci_request(struct mmc_ho
 	host->cmd_is_stop = 0;
 	host->mrq = mrq;
 
-	s3cmci_send_request(mmc);
+	if (s3cmci_card_present(host) == 0) {
+		dbg(host, dbg_err, "%s: no medium present\n", __func__);
+		host->mrq->cmd->error = -ENOMEDIUM;
+		mmc_request_done(mmc, mrq);
+	} else
+		s3cmci_send_request(mmc);
 }
 
 static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
include/asm-arm/plat-s3c24xx/mci.h +1 -0
Index: linux-2.6.26-rc8-next20080627/include/asm-arm/plat-s3c24xx/mci.h
===================================================================
@@ -3,6 +3,7 @@
 
 struct s3c24xx_mci_pdata {
 	unsigned int	wprotect_invert : 1;
+	unsigned int	detect_invert : 1;   /* set => detect active high. */
 
 	unsigned int	gpio_detect;
 	unsigned int	gpio_wprotect;
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#23 lore raw

PATCH v4 15/17 MMC: S3C24XX: Update error debugging.

In reply to Ben Dooks

Add better debugging to show where errors are being generated, as some error codes can come from several different code paths.

Also fix the error return path from s3cmci_setup_data() to return the error it returned to the request.

drivers/mmc/host/s3cmci.c +10 -2
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -451,6 +451,7 @@ static irqreturn_t s3cmci_irq(int irq, v
 	}
 
 	if (mci_csta & S3C2410_SDICMDSTAT_CMDTIMEOUT) {
+		dbg(host, dbg_err, "CMDSTAT: error CMDTIMEOUT\n");
 		cmd->error = -ETIMEDOUT;
 		host->status = "error: command timeout";
 		goto fail_transfer;
@@ -506,12 +507,14 @@ static irqreturn_t s3cmci_irq(int irq, v
 	/* Check for FIFO failure */
 	if (host->is2440) {
 		if (mci_fsta & S3C2440_SDIFSTA_FIFOFAIL) {
+			dbg(host, dbg_err, "FIFO failure\n");
 			host->mrq->data->error = -EILSEQ;
 			host->status = "error: 2440 fifo failure";
 			goto fail_transfer;
 		}
 	} else {
 		if (mci_dsta & S3C2410_SDIDSTA_FIFOFAIL) {
+			dbg(host, dbg_err, "FIFO failure\n");
 			cmd->data->error = -EILSEQ;
 			host->status = "error:  fifo failure";
 			goto fail_transfer;
@@ -519,18 +522,21 @@ static irqreturn_t s3cmci_irq(int irq, v
 	}
 
 	if (mci_dsta & S3C2410_SDIDSTA_RXCRCFAIL) {
+		dbg(host, dbg_err, "bad data crc (outgoing)\n");
 		cmd->data->error = -EILSEQ;
 		host->status = "error: bad data crc (outgoing)";
 		goto fail_transfer;
 	}
 
 	if (mci_dsta & S3C2410_SDIDSTA_CRCFAIL) {
+		dbg(host, dbg_err, "bad data crc (incoming)\n");
 		cmd->data->error = -EILSEQ;
 		host->status = "error: bad data crc (incoming)";
 		goto fail_transfer;
 	}
 
 	if (mci_dsta & S3C2410_SDIDSTA_DATATIMEOUT) {
+		dbg(host, dbg_err, "data timeout\n");
 		cmd->data->error = -ETIMEDOUT;
 		host->status = "error: data timeout";
 		goto fail_transfer;
@@ -957,8 +963,9 @@ static void s3cmci_send_request(struct m
 		host->dcnt++;
 
 		if (res) {
-			cmd->error = -EINVAL;
-			cmd->data->error = -EINVAL;
+			dbg(host, dbg_err, "setup data error %d\n", res);
+			cmd->error = res;
+			cmd->data->error = res;
 
 			mmc_request_done(mmc, mrq);
 			return;
@@ -970,6 +977,7 @@ static void s3cmci_send_request(struct m
 			res = s3cmci_prepare_pio(host, cmd->data);
 
 		if (res) {
+			dbg(host, dbg_err, "data prepare error %d\n", res);
 			cmd->error = res;
 			cmd->data->error = res;
 
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#24 lore raw

PATCH v4 16/17 MMC: S3C24XX: Add maintainer entry

In reply to Ben Dooks

Add Ben Dooks as S3C24XX SD/MMC driver maintainer.

MAINTAINERS +7 -0
Index: linux-2.6.26-rc8-next20080627/MAINTAINERS
===================================================================
@@ -3544,6 +3544,13 @@ L:	[email protected]
 W:	http://www.ibm.com/developerworks/linux/linux390/
 S:	Supported
 
+S3C24XX SD/MMC Driver
+P:	Ben Dooks
+M:	[email protected]
+L:	[email protected] (subscribers-only)
+L:	[email protected]
+S:	Supported
+
 SAA7146 VIDEO4LINUX-2 DRIVER
 P:	Michael Hunold
 M:	[email protected]
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#25 lore raw

PATCH v4 17/17 MMC: S3C24XX:

In reply to Ben Dooks

The hardware does not support any multi-block transfers with an block-size that is not aligned. Also the driver itself does not support single block non-32bit transfers either.

Ensure that the s3cmci_setup_data() returns the appropriate error if we encounter this.

drivers/mmc/host/s3cmci.c +11 -0
Index: linux-2.6.26-rc8-next20080627/drivers/mmc/host/s3cmci.c
===================================================================
@@ -808,6 +808,17 @@ static int s3cmci_setup_data(struct s3cm
 		return 0;
 	}
 
+	if ((data->blksz & 3) != 0) {
+		/* We cannot deal with unaligned blocks with more than
+		 * one block being transfered. */
+
+		if (data->blocks > 1)
+			return -EINVAL;
+
+		/* No support yet for non-word block transfers. */
+		return -EINVAL;
+	}
+
 	while (readl(host->base + S3C2410_SDIDSTA) &
 	       (S3C2410_SDIDSTA_TXDATAON | S3C2410_SDIDSTA_RXDATAON)) {
 
Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
author
#26 lore raw

Re: [patch v4 17/17] MMC: S3C24XX:

On Mon, Jun 30, 2008 at 04:26:04PM +0100, Ben Dooks wrote:

Should I resend this one, or the entire series with the subject line of this patch corrected?

Signature · 3 lines
Ben ([email protected], http://www.fluff.org/)

  'a smiley only costs 4 bytes'
#27 lore raw

Re: [patch v4 17/17] MMC: S3C24XX:

Quoted 5 lines · On Mon, 30 Jun 2008 16:36:11 +0100 Ben Dooks <[email protected]> wrote:

On Mon, Jun 30, 2008 at 04:26:04PM +0100, Ben Dooks wrote:

Should I resend this one, or the entire series with the subject line of this patch corrected?

That's ok. I can fix it up manually.

Signature · 9 lines
     -- Pierre Ossman

  Linux kernel, MMC maintainer        http://www.kernel.org
  rdesktop, core developer          http://www.rdesktop.org

  WARNING: This correspondence is being monitored by the
  Swedish government. Make sure your server uses encryption
  for SMTP traffic and consider using PGP for end-to-end
  encryption.