kconfig: fix typos: "Suport" -> "Support"
Subsystems (7)
PATCH 1/1 kconfig: fix typos: "Suport" -> "Support"
Signed-off-by Heikki Orsila <[email protected]>
--- drivers/misc/Kconfig | 2 +- init/Kconfig | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/misc/Kconfig +1 -1
@@ -315,7 +315,7 @@ config THINKPAD_ACPI_VIDEO If you are not sure, say Y here. config THINKPAD_ACPI_HOTKEY_POLL - bool "Suport NVRAM polling for hot keys" + bool "Support NVRAM polling for hot keys" depends on THINKPAD_ACPI default y ---help---
init/Kconfig +1 -1
@@ -486,7 +486,7 @@ config PID_NS default n depends on NAMESPACES && EXPERIMENTAL help - Suport process id namespaces. This allows having multiple + Support process id namespaces. This allows having multiple process with the same pid as long as they are in different pid namespaces. This is a building block of containers.
Signature · 1 line
1.5.5.1.1.ga5e5c
Sam Ravnborg
AppliedQuoted 5 lines · Heikki Orsila
Signed-off-by Heikki Orsila <[email protected]>--- drivers/misc/Kconfig | 2 +- init/Kconfig | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
Applied,
Sam
PATCH 1/1 more "suport -> support" typo fix from git grep
$ git grep -w -i -n suport
Documentation/video4linux/bttv/Sound-FAQ:85:Another one with bt878 suport is available from
drivers/media/video/uvc/uvc_video.c:861: /* Some webcams don't suport GET_DEF request on the probe control. We
drivers/net/wireless/ath5k/ath5k.h:223: * channels. To use this feature your Access Point must also suport it.
net/ipv4/tcp_cong.c:4: * Based on ideas from I/O scheduler suport and Web100.
net/sctp/sm_statefuns.c:3793: /* Make sure that we suport the HMAC algorithm from the authSigned-off-by Denis Cheng <[email protected]>
---
To Heikki and typo-fix patches authors:
Anytime intend to make a typo-fix patch, you'd better do a git-grep first, that would fix all this typo in the whole tree one time. thanks.
Documentation/video4linux/bttv/Sound-FAQ | 2 +- drivers/media/video/uvc/uvc_video.c | 2 +- drivers/net/wireless/ath5k/ath5k.h | 2 +- net/ipv4/tcp_cong.c | 2 +- net/sctp/sm_statefuns.c | 2 +- 5 files changed, 5 insertions(+), 5 deletions(-)
Documentation/video4linux/bttv/Sound-FAQ +1 -1
@@ -82,7 +82,7 @@ card installed, you might to check out if you can read these registers values used by the windows driver. A tool to do this is available from ftp://telepresence.dmem.strath.ac.uk/pub/bt848/winutil, but it does'nt work with bt878 boards according to some reports I received. -Another one with bt878 suport is available from +Another one with bt878 support is available from http://btwincap.sourceforge.net/Files/btspy2.00.zip You might also dig around in the *.ini files of the Windows applications.
drivers/media/video/uvc/uvc_video.c +1 -1
@@ -858,7 +858,7 @@ int uvc_video_init(struct uvc_video_device *video)*/ usb_set_interface (video->dev->udev, video->streaming->intfnum,0 ); -/* Some webcams don't suport GET_DEF request on the probe control. We +/* Some webcams don't support GET_DEF request on the probe control. We * fall back to GET_CUR if GET_DEF fails. */ if ((ret = uvc_get_video_ctrl(video, probe, 1, GET_DEF)) < 0 &&
drivers/net/wireless/ath5k/ath5k.h +1 -1
@@ -220,7 +220,7 @@ struct ath5k_srev_name {* Modulation for Atheros' Turbo G and Turbo A, its supposed to provide a * throughput transmission speed up to 40Mbit/s-60Mbit/s at a 108Mbit/s * signaling rate achieved through the bonding of two 54Mbit/s 802.11g -* channels. To use this feature your Access Point must also suport it. +* channels. To use this feature your Access Point must also support it. * There is also a distinction between "static" and "dynamic" turbo modes: * * - Static: is the dumb version: devices set to this mode stick to it until
net/ipv4/tcp_cong.c +1 -1
@@ -1,7 +1,7 @@/* * Plugable TCP congestion control support and newReno * congestion control. -* Based on ideas from I/O scheduler suport and Web100. +* Based on ideas from I/O scheduler support and Web100. * * Copyright (C) 2005 Stephen Hemminger <[email protected]> */
net/sctp/sm_statefuns.c +1 -1
@@ -3790,7 +3790,7 @@ static sctp_ierror_t sctp_sf_authenticate(const struct sctp_endpoint *ep, chunk->subh.auth_hdr = auth_hdr;skb_pull (chunk->skb,sizeof (struct sctp_authhdr )); -/* Make sure that we suport the HMAC algorithm from the auth +/* Make sure that we support the HMAC algorithm from the auth * chunk. */ if (!sctp_auth_asoc_verify_hmac_id (asoc, auth_hdr->hmac_id))
Signature · 1 line
1.5.6.GIT