bnx2 hardware VLAN acceleration and PF_PACKET/tap interfaces
Subsystems (2)
I'm struggling with VLAN tags being stripped the bnx2 driver/hardware when hardware VLAN acceleration is enabled.
I'm trying to (a) tcpdump(8) on the main interface and see tagged traffic and (b) place the main interface into a bridge group and attach a tap interface to the bridge to give KVM virtual machines access to that interface. The VMs would then have their own choice of VLANs without having to create separate VLAN subints, bridge groups, and tap interfaces on the KVM host for each VLAN that a VM needs access to.
I've seen these threads, which indicate this is due to the implementation particulars of hardware VLAN acceleration:
http://marc.info/?l=linux-netdev&m=117269169822297&w=2
http://marc.info/?l=linux-netdev&m=119395331216242&w=2
The adapters are "NetXtreme II BCM5708S Gigabit Ethernet rev 12" in IBM BladeCenter chassis. I've tried disabling the use of ASF_ENABLE_FLAG in bnx2, but this doesn't seem to have changed its behavior any. The Broadcom firmware upgarde utility says ASF isn't supported by this chipset when I try to 'cfg -asf 0', so perhaps this adapter doesn't support ASF and I'm barking up the wrong tree?
Flailing around, I tried #defining BCM_VLAN to 0 to disable hardware VLAN acceleration. This breaks the driver build since there's an unguarded use of struct bnx2->vlgrp in bnx2_start_xmit().
I'm also seeing some tcpdump(8) behavior that I don't understand. When I tcpdump the main interface (not the VLAN subint), I see only *outbound* traffic for the last VLAN configured on the interface, and no other traffic. Is this some side-effect of the hardware VLAN acceleration?
Is there any hope of having this work? I'm working with 2.6.24 (from Ubuntu 8.04 FWIW) and have glanced at the bnx2 driver in 2.6.25, which seems essentially the same.
john
Signature · 3 lines
John Morrissey _o /\ ---- __o [email protected] _-< \_ / \ ---- < \, www.horde.net/ __(_)/_(_)________/ \_______(_) /_(_)__
Quoted 27 lines · John Morrissey
I'm struggling with VLAN tags being stripped the bnx2 driver/hardware when hardware VLAN acceleration is enabled.
I'm trying to (a) tcpdump(8) on the main interface and see tagged traffic and (b) place the main interface into a bridge group and attach a tap interface to the bridge to give KVM virtual machines access to that interface. The VMs would then have their own choice of VLANs without having to create separate VLAN subints, bridge groups, and tap interfaces on the KVM host for each VLAN that a VM needs access to.
I've seen these threads, which indicate this is due to the implementation particulars of hardware VLAN acceleration:
http://marc.info/?l=linux-netdev&m=117269169822297&w=2
http://marc.info/?l=linux-netdev&m=119395331216242&w=2The adapters are "NetXtreme II BCM5708S Gigabit Ethernet rev 12" in IBM BladeCenter chassis. I've tried disabling the use of
ASF_ENABLE_FLAGin bnx2, but this doesn't seem to have changed its behavior any. The Broadcom firmware upgarde utility says ASF isn't supported by this chipset when I try to 'cfg -asf 0', so perhaps this adapter doesn't support ASF and I'm barking up the wrong tree?Flailing around, I tried #defining
BCM_VLANto 0 to disable hardware VLAN acceleration. This breaks the driver build since there's an unguarded use of structbnx2->vlgrpinbnx2_start_xmit().
Quoted 8 lines
I'm also seeing some tcpdump(8) behavior that I don't understand. When I tcpdump the main interface (not the VLAN subint), I see only *outbound* traffic for the last VLAN configured on the interface, and no other traffic. Is this some side-effect of the hardware VLAN acceleration?
Is there any hope of having this work? I'm working with 2.6.24 (from Ubuntu 8.04 FWIW) and have glanced at the bnx2 driver in 2.6.25, which seems essentially the same.
These patches I posted this morning are supposed to fix this: