USB: add USB test and measurement class driver
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 12 lines · On Thursday 28 August 2008 18:21:09 Greg KH wrote:
Quoted 10 lines · Marcel Janssen
Hello Greg,
I've got me a bit confused there :-)
We currently only use the suspend/resume in our device which works on a received request from the PC.
Basically sending suspend will make the device enter this mode. When the PC enters this mode, it's also clear it will send a resume when resuming from standby. But, how is this supposed to work when the PC is not in sleep mode.....how will the device wake up ?
Quoted 3 lines
It should "automatically" wake up if something happens to it. The USB spec calls this out as to how this should work. If the devices don't support this, we don't have to add support for it :)
Actually this is a good point.
The USB spec mentions that the device should suspend when a constant idle state is detected for more than 3.0ms.
I either have not seen that happening before or I missed something when writing my firmware. I'll keep an eye on my USB analyzer though :-) Although it's a good thing to keep to the spec, I also believe that in the case of a test and measurement device suspending the device may be an unwanted behaviour but perhaps I do misinterpret this part of the spec here.
Anyway, this is no issue for self-powered devices, which is probably the majority in this class because most test & measurement devices need a good power supply and USB just isn't fit for that unless you're able to make a clean power from that (which is possible of course).
Our device is both USB and self powered, but when in USB powered mode it will only suspend when the host goes in sleep mode.
To be honest I would put suspend mode far down on the priority list :-)
regards,
Marcel
Quoted 28 lines · Marcel Janssen
Quoted 12 lines · On Thursday 28 August 2008 18:21:09 Greg KH wrote:
Quoted 10 lines · Marcel Janssen
Hello Greg,
I've got me a bit confused there :-)
We currently only use the suspend/resume in our device which works on a received request from the PC.
Basically sending suspend will make the device enter this mode. When the PC enters this mode, it's also clear it will send a resume when resuming from standby. But, how is this supposed to work when the PC is not in sleep mode.....how will the device wake up ?Quoted 3 lines
It should "automatically" wake up if something happens to it. The USB spec calls this out as to how this should work. If the devices don't support this, we don't have to add support for it :)
Actually this is a good point.
The USB spec mentions that the device should suspend when a constant idle state is detected for more than 3.0ms.
I either have not seen that happening before or I missed something when writing my firmware. I'll keep an eye on my USB analyzer though :-) Although it's a good thing to keep to the spec, I also believe that in the case of a test and measurement device suspending the device may be an unwanted behaviour but perhaps I do misinterpret this part of the spec here.
Quoted 8 lines
Anyway, this is no issue for self-powered devices, which is probably the majority in this class because most test & measurement devices need a good power supply and USB just isn't fit for that unless you're able to make a clean power from that (which is possible of course).
Our device is both USB and self powered, but when in USB powered mode it will only suspend when the host goes in sleep mode.To be honest I would put suspend mode far down on the priority list :-)
Ok, thanks for letting us know, if they are self-powered, this shouldn't be much of an issue. Let's focus on getting the current driver working again :)
thanks,
greg k-h
Quoted 6 lines
Quoted 6 lines
I either have not seen that happening before or I missed something when writing my firmware. I'll keep an eye on my USB analyzer though :-) Although it's a good thing to keep to the spec, I also believe that in the case of a test and measurement device suspending the device may be an unwanted behaviour but perhaps I do misinterpret this part of the spec here.
For the record, the "gadgetfs" interface was originally developed with userspace USB TMC implementations in mind. I don't recall whether that effort got out of the lab though.
The issue of suspend/resume explicitly came up. The scenario which stuck in my mind was that when the TMC device was in USB-level suspend state, the code on the peripheral would need to know about that so it could re-enable manual controls. The host could no longer be issuing commands. (Some of these folk were on the TMC design team.)
One of the customers didn't seem to like the notion of not being able to turn off stress tests on a $US 20,000 engine ... and watching the device(s) under test blow up. Accidental destruction == bad, it seems!
So I think you probably do misinterpret the spec. That issue was not only discussed, but proper handling for it was identified.
- Dave
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 5 lines · Marcel Janssen
My basic concern was like the stress test, but also devices that take a long time to perform measurements (long averaging/integrating) and have no bus activity during that time. On the other hand I worry about the variation in measurement results if a device keeps going in low power mode all the time.
Do you know of any reasonably cheap USB TMC devices out there that I could buy to help test this driver here? I looked at the device that your company makes, but I don't think it falls into the "cheap" category :)
thanks,
greg k-h