4xx: Cleanup PLU405 platform file
PATCH 4/6 4xx: Cleanup PLU405 platform file
This patch
- wraps some long lines
- removes unused/obsolete functions: misc_init_f() and initdram()
Signed-off-by Matthias Fuchs <[email protected]>
--- board/esd/plu405/plu405.c | 58 ++++++++++++++++---------------------------- 1 files changed, 21 insertions(+), 37 deletions(-)
board/esd/plu405/plu405.c +21 -37
@@ -65,11 +65,9 @@ au_image_t au_image[] = {int N_AU_IMAGES = (sizeof (au_image) /sizeof (au_image[0 ])); -/* Prototypes */ int gunzip (void *,int ,unsigned char *,unsigned long *); -int board_early_init_f (void ) {/*
@@ -89,24 +87,18 @@ int board_early_init_f (void)mtdcr (uiccr,0x00000000 );/* set all to be non-critical*/ mtdcr (uicpr,0xFFFFFF99 );/* set int polarities */ mtdcr (uictr,0x10000000 );/* set int trigger levels */ -mtdcr (uicvcr,0x00000001 );/* set vect base=0,INT0 highest priority*/ +mtdcr (uicvcr,0x00000001 );/* set vect base=0,INT0 highest prio */ mtdcr (uicsr,0xFFFFFFFF );/* clear all ints */ /* -* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us +* EBC Configuration Register: set ready timeout to +* 512 ebc-clks -> ca. 15 us */ mtebc (epcr,0xa8400000 );/* ebc always driven */ return 0 ; } - -int misc_init_f (void ) -{ -return 0 ;/* dummy implementation */ -} - -int misc_init_r (void ) {unsigned char *duart0_mcr = (unsigned char *)((ulong )DUART0_BA +4 );
@@ -132,13 +124,16 @@ int misc_init_r (void)printf ("\nFPGA: Booting failed " );switch (status) {case ERROR_FPGA_PRG_INIT_LOW : -printf ("(Timeout: INIT not low after asserting PROGRAM*)\n " ); +printf ("(Timeout: INIT not low " +"after asserting PROGRAM*)\n" );break ;case ERROR_FPGA_PRG_INIT_HIGH : -printf ("(Timeout: INIT not high after deasserting PROGRAM*)\n " ); +printf ("(Timeout: INIT not high " +"after deasserting PROGRAM*)\n" );break ;case ERROR_FPGA_PRG_DONE : -printf ("(Timeout: DONE not high after programming FPGA)\n " ); +printf ("(Timeout: DONE not high " +"after programming FPGA)\n" );break ; }
@@ -184,15 +179,16 @@ int misc_init_r (void)/* * Reset external DUARTs */ -out_be32 ((void *)GPIO0_OR ,in_be32 ((void *)GPIO0_OR ) |CFG_DUART_RST );/* set reset to high */ -udelay (10 );/* wait 10us */ -out_be32 ((void *)GPIO0_OR ,in_be32 ((void *)GPIO0_OR ) & ~CFG_DUART_RST );/* set reset to low */ -udelay (1000 );/* wait 1ms */ +out_be32 ((void *)GPIO0_OR ,in_be32 ((void *)GPIO0_OR ) |CFG_DUART_RST ); +udelay (10 ); +out_be32 ((void *)GPIO0_OR ,in_be32 ((void *)GPIO0_OR ) & ~CFG_DUART_RST ); +udelay (1000 );/* * Set NAND-FLASH GPIO signals to default */ -out_be32 ((void *)GPIO0_OR ,in_be32 ((void *)GPIO0_OR ) & ~(CFG_NAND_CLE |CFG_NAND_ALE )); +out_be32 ((void *)GPIO0_OR , +in_be32 ((void *)GPIO0_OR ) & ~(CFG_NAND_CLE |CFG_NAND_ALE ));out_be32 ((void *)GPIO0_OR ,in_be32 ((void *)GPIO0_OR ) |CFG_NAND_CE );/*
@@ -210,7 +206,6 @@ int misc_init_r (void)return (0 ); } -/* * Check Board Identity: */
@@ -231,18 +226,6 @@ int checkboard (void)return 0 ; } - -phys_size_t initdram (int board_type) -{ -unsigned long val; - -mtdcr (memcfga, mem_mb0cf); - val =mfdcr (memcfgd); - -return (4 *1024 *1024 << ((val &0x000e0000 ) >>17 )); -} - -#ifdef CONFIG_IDE_RESET void ide_set_reset (int on) {
@@ -260,7 +243,6 @@ void ide_set_reset(int on) }#endif /* CONFIG_IDE_RESET */ -void reset_phy (void ) {#ifdef CONFIG_LXT971_NO_SLEEP
@@ -272,7 +254,6 @@ void reset_phy(void)#endif } -#if defined(CFG_EEPROM_WREN )/* Input: <dev_addr> I2C address of EEPROM device to enable. * <state> -1: deliver current state
@@ -290,17 +271,20 @@ int eeprom_write_enable (unsigned dev_addr, int state)switch (state) {case 1 :/* Enable write access, clear bit GPIO0. */ -out_be32 ((void *)GPIO0_OR ,in_be32 ((void *)GPIO0_OR ) & ~CFG_EEPROM_WP ); +out_be32 ((void *)GPIO0_OR , +in_be32 ((void *)GPIO0_OR ) & ~CFG_EEPROM_WP ); state =0 ;break ;case 0 :/* Disable write access, set bit GPIO0. */ -out_be32 ((void *)GPIO0_OR ,in_be32 ((void *)GPIO0_OR ) |CFG_EEPROM_WP ); +out_be32 ((void *)GPIO0_OR , +in_be32 ((void *)GPIO0_OR ) |CFG_EEPROM_WP ); state =0 ;break ;default :/* Read current status back. */ - state = (0 == (in_be32 ((void *)GPIO0_OR ) &CFG_EEPROM_WP )); + state = (0 == (in_be32 ((void *)GPIO0_OR ) & +CFG_EEPROM_WP ));break ; } }
Signature · 1 line
1.5.3