Skip to contentSkip to conversation

ocfs2: Fix a bug in direct IO read.

PATCH New Tao Ma 2 participants 2 messages Sep 2, 2008 – Sep 3, 2008 OCFS2

lore
Share & tools
lore

Tao Ma

author
#0 lore raw

PATCH 1/1 ocfs2: Fix a bug in direct IO read.

ocfs2 will become read-only if we try to read the bytes which pass the end of i_size. This can be easily reproduced by following steps:
1. mkfs a ocfs2 volume with bs=4k cs=4k and nosparse.
2. create a small file(say less than 100 bytes) and we will create the file which is allocated 1 cluster.
3. read 8196 bytes from the kernel using O_DIRECT which exceeds the limit.
4. The ocfs2 volume becomes read-only and dmesg shows:
OCFS2: ERROR (device sda13): ocfs2_direct_IO_get_blocks:
Inode 66010 has a hole at block 1
File system is now read-only due to the potential of on-disk corruption. Please run fsck.ocfs2 once the file system is unmounted.

I have checked the code of 1.2 and copy the read check there. And actually I think even with sparse-enabled, this read check is ok.

---
 fs/ocfs2/aops.c |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)
fs/ocfs2/aops.c +8 -0
index 80fa3fc..f27c1cc 100644
@@ -576,6 +576,14 @@ static int ocfs2_direct_IO_get_blocks(struct inode *inode, sector_t iblock,
 	inode_blocks = ocfs2_blocks_for_bytes(inode->i_sb, i_size_read(inode));
 
 	/*
+	 * For a read which begins past the end of file, we return a hole.
+	 */
+	if (!create && (iblock >= inode_blocks)) {
+		ret = 0;
+		goto bail;
+	}
+
+	/*
 	 * Any write past EOF is not allowed because we'd be extending.
 	 */
 	if (create && (iblock + max_blocks) > inode_blocks) {
Signature · 1 line
1.5.4.GIT
#1 lore raw

PATCH 1/1 ocfs2: Fix a bug in direct IO read.

Quoted 12 lines · Tao Ma

ocfs2 will become read-only if we try to read the bytes which pass the end of i_size. This can be easily reproduced by following steps:
1. mkfs a ocfs2 volume with bs=4k cs=4k and nosparse.
2. create a small file(say less than 100 bytes) and we will create the file which is allocated 1 cluster.
3. read 8196 bytes from the kernel using O_DIRECT which exceeds the limit.
4. The ocfs2 volume becomes read-only and dmesg shows:
OCFS2: ERROR (device sda13): ocfs2_direct_IO_get_blocks:
Inode 66010 has a hole at block 1
File system is now read-only due to the potential of on-disk corruption. Please run fsck.ocfs2 once the file system is unmounted.

Quoted 2 lines

I have checked the code of 1.2 and copy the read check there. And actually I think even with sparse-enabled, this read check is ok.

Hmm - in this case we're supposed to return a short read. I think actually the fix is a bit below at this line, where you're hitting the problem:

	if (!ocfs2_sparse_alloc(OCFS2_SB(inode->i_sb)) && !p_blkno) {
		ocfs2_error(inode->i_sb,
			    "Inode %llu has a hole at block %llu\n",
			    (unsigned long long)OCFS2_I(inode)->ip_blkno,
			    (unsigned long long)iblock);
		ret = -EROFS;
		goto bail;
	}

How about changing that to:

        if (!ocfs2_sparse_alloc(OCFS2_SB(inode->i_sb)) && !p_blkno && create) {

So that we only check if there's a write (which really *is* something that shouldn't happen for Ocfs2).

The rest of the code looks like it should handle things by clearing the mapped bitt, which is correct.

	--Mark
Quoted 27 lines
---
 fs/ocfs2/aops.c |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)
fs/ocfs2/aops.c +8 -0
index 80fa3fc..f27c1cc 100644
@@ -576,6 +576,14 @@ static int ocfs2_direct_IO_get_blocks(struct inode *inode, sector_t iblock,
 	inode_blocks = ocfs2_blocks_for_bytes(inode->i_sb, i_size_read(inode));
 
 	/*
+	 * For a read which begins past the end of file, we return a hole.
+	 */
+	if (!create && (iblock >= inode_blocks)) {
+		ret = 0;
+		goto bail;
+	}
+
+	/*
 	 * Any write past EOF is not allowed because we'd be extending.
 	 */
 	if (create && (iblock + max_blocks) > inode_blocks) {
Signature · 1 line
1.5.4.GIT

--
Mark Fasheh