Skip to contentSkip to conversation

powerpc/83xx: mpc836x_mds: add support for USB Host/Gadget

PATCH New Anton Vorontsov 1 participant 1 message Sep 4, 2008

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 2/2 powerpc/83xx: mpc836x_mds: add support for USB Host/Gadget

Various changes to support QE USB Host and Gadget on MPC8360E-MDS boards:

- Update the device tree per QE USB bindings;
- Configure QE Par IO;
- Set up BCSR for both USB Host and Peripheral modes;
- Add timer (GTM) node;
- Add gpio-controller node for BCSR13 bank;
- Select FSL_GTM and QE_USB.

The work is loosely based on Li Yang's patch[1], which is used to support peripheral mode only.

[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html

The s-o-b line of the original patch preserved here.

---

Added qe_usb_clock_set() for peripheral case, since the udc driver does not manage the clocks.

Also, simple of gpio driver is user-selectable now, so we don't need to select it explicitly.

 arch/powerpc/boot/dts/mpc836x_mds.dts     |   44 +++++++++++++++++++++++++++-
 arch/powerpc/platforms/83xx/Kconfig       |    2 +
 arch/powerpc/platforms/83xx/mpc836x_mds.c |   45 ++++++++++++++++++++++++++++-
 3 files changed, 88 insertions(+), 3 deletions(-)
arch/powerpc/boot/dts/mpc836x_mds.dts +42 -2
index ada8446..0be98f3 100644
@@ -69,8 +69,19 @@
 		};
 
 		bcsr@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
 			device_type = "board-control";
 			reg = <1 0 0x8000>;
+			ranges = <0 1 0 0x8000>;
+
+			bcsr13: gpio-controller@d {
+				#gpio-cells = <2>;
+				compatible = "fsl,mpc8360mds-bcsr-gpio",
+					     "simple-gpio-bank";
+				reg = <0xd 1>;
+				gpio-controller;
+			};
 		};
 	};
 
@@ -191,10 +202,21 @@
 		};
 
 		par_io@1400 {
+			#address-cells = <1>;
+			#size-cells = <1>;
 			reg = <0x1400 0x100>;
+			ranges = <0 0x1400 0x100>;
 			device_type = "par_io";
 			num-ports = <7>;
 
+			qe_pio_b: gpio-controller@18 {
+				#gpio-cells = <2>;
+				compatible = "fsl,mpc8360-qe-pario-bank",
+					     "fsl,mpc8323-qe-pario-bank";
+				reg = <0x18 0x18>;
+				gpio-controller;
+			};
+
 			pio1: ucc_pin@01 {
 				pio-map = <
 			/* port  pin  dir  open_drain  assignment  has_irq */
@@ -278,6 +300,15 @@
 			};
 		};
 
+		timer@440 {
+			compatible = "fsl,mpc8360-qe-gtm",
+				     "fsl,qe-gtm", "fsl,gtm";
+			reg = <0x440 0x40>;
+			clock-frequency = <132000000>;
+			interrupts = <12 13 14 15>;
+			interrupt-parent = <&qeic>;
+		};
+
 		spi@4c0 {
 			cell-index = <0>;
 			compatible = "fsl,spi";
@@ -297,11 +328,20 @@
 		};
 
 		usb@6c0 {
-			compatible = "qe_udc";
+			compatible = "fsl,mpc8360-qe-usb",
+				     "fsl,mpc8323-qe-usb";
 			reg = <0x6c0 0x40 0x8b00 0x100>;
 			interrupts = <11>;
 			interrupt-parent = <&qeic>;
-			mode = "slave";
+			fsl,fullspeed-clock = "clk21";
+			fsl,lowspeed-clock = "brg9";
+			gpios = <&qe_pio_b  2 0   /* USBOE */
+				 &qe_pio_b  3 0   /* USBTP */
+				 &qe_pio_b  8 0   /* USBTN */
+				 &qe_pio_b  9 0   /* USBRP */
+				 &qe_pio_b 11 0   /* USBRN */
+				 &bcsr13    5 0   /* SPEED */
+				 &bcsr13    4 1>; /* POWER */
 		};
 
 		enet0: ucc@2000 {
arch/powerpc/platforms/83xx/Kconfig +2 -0
index 6159c5d..b4ee8f1 100644
@@ -58,6 +58,8 @@ config MPC836x_MDS
 	bool "Freescale MPC836x MDS"
 	select DEFAULT_UIMAGE
 	select QUICC_ENGINE
+	select QE_USB
+	select FSL_GTM
 	help
 	  This option enables support for the MPC836x MDS Processor Board.
 
arch/powerpc/platforms/83xx/mpc836x_mds.c +44 -1

53 lines not on this page · raw message

Signature · 1 line
1.5.6.3