ACPI PnP on Intel MU440EX
Hi,
I have trouble with ACPI PnP on one of my machines (Intel MU440EX motherboard made in '98). ACPI PnP doesn't detect built-in parallel port (PNPBIOS does and the port works because I use it to print regularly). I know that I can turn ACPI PnP off by editing .config or using pnpacpi=off boot parameter. I just want to report this problem before PNPBIOS support is dropped (as written in kernel docs).
I have no experience with kernel development or debugging but lots of experience with userspace development in C so you can ask whatever information you need.
Regards,
Martin Doucha
Quoted 6 lines · Martin Doucha
I have trouble with ACPI PnP on one of my machines (Intel MU440EX motherboard made in '98). ACPI PnP doesn't detect built-in parallel port (PNPBIOS does and the port works because I use it to print regularly). I know that I can turn ACPI PnP off by editing .config or using pnpacpi=off boot parameter. I just want to report this problem before PNPBIOS support is dropped (as written in kernel docs).
Thanks very much for the report. This sounds like it could be a PNPACPI issue, which I am very interested in fixing.
Can you please turn on CONFIG_PNP_DEBUG in your .config and collect the complete dmesg log with and without "pnpacpi=off"?
I do have an "lspnp" that works with PNPACPI here:
http://kernel.org/pub/linux/kernel/people/helgaas/pnputils-0.1.tar.bz2
but it's not widely used. The debug information from the config option above is usually more useful.
Bjorn
Quoted 6 lines · Bjorn Helgaas
Thanks very much for the report. This sounds like it could be a PNPACPI issue, which I am very interested in fixing.
Can you please turn on
CONFIG_PNP_DEBUGin your .config and collect the complete dmesg log with and without "pnpacpi=off"?
Quoted 6 lines
I do have an "lspnp" that works with PNPACPI here:
http://kernel.org/pub/linux/kernel/people/helgaas/pnputils-0.1.tar.bz2
but it's not widely used. The debug information from the config option above is usually more useful.Bjorn
I'm sorry it took me so long, here's the output of lspnp -vvv from both PNPBIOS and ACPI PnP (same kernel, the only difference is pnpacpi=off boot argument). I can't find any mention of my parallel port in ACPI PnP output but it's the last listed device (00:15 PNP0400) in PNPBIOS output.
Regards,
Martin Doucha
00:00 PNP0a03 (unknown)
state = active
allocated resources:
io 0xcf8-0xcff
00:01 PNP0303 (unknown)
state = active
allocated resources:
io 0x60-0x60
io 0x64-0x64
irq 100:02 PNP0f13 (unknown)
state = active
allocated resources:
irq 12
00:03 PNP0201 (unknown)
state = active
allocated resources:
io 0x0-0xf
io 0x80-0x91
io 0x94-0x9f
io 0xc0-0xdf
io 0x40b-0x40b
io 0x410-0x43f
io 0x481-0x483
io 0x487-0x487
io 0x489-0x489
io 0x4d6-0x4d6
dma 400:04 PNP0b00 (unknown)
state = active
allocated resources:
io 0x70-0x71
irq 8
00:05 PNP0c04 (unknown)
state = active
allocated resources:
io 0xf0-0xff
irq 1300:06 PNP0800 (unknown)
state = active
allocated resources:
io 0x61-0x61
00:07 PNP0c02 (unknown)
state = active
allocated resources:
io 0x7000-0x700f
io 0x8000-0x803f00:08 PNP0700 (unknown)
state = active
allocated resources:
io 0x3f0-0x3f5
io 0x3f7-0x3f7
irq 6
dma 2
possible resources:
Dependent: 01 - Priority preferred
port 0x3f0-0x3f0, align 0x0, size 0x6, 16-bit address decoding port 0x3f7-0x3f7, align 0x0, size 0x1, 16-bit address decoding irq 6 High-Edge
dma 2 8-bit compatible
00:09 PNP0501 (unknown)
state = active
allocated resources:
io 0x3f8-0x3ff
irq 4
possible resources:
Dependent: 01 - Priority preferred
port 0x3f8-0x3f8, align 0x0, size 0x8, 16-bit address decoding irq 4 High-Edge
Dependent: 02 - Priority preferred
port 0x3e8-0x3e8, align 0x0, size 0x8, 16-bit address decoding irq 4 High-Edge
Dependent: 03 - Priority preferred
port 0x2f8-0x2f8, align 0x0, size 0x8, 16-bit address decoding irq 3 High-Edge
Dependent: 04 - Priority preferred
port 0x2e8-0x2e8, align 0x0, size 0x8, 16-bit address decoding irq 3 High-Edge
Dependent: 05 - Priority functional
port 0x100-0x3f8, align 0x7, size 0x8, 16-bit address decoding irq 1,3,4,5,6,7,8,10,11,12,13,14,15 High-Edge
00:0a PNP8294 (unknown)
state = disabled
possible resources:
Dependent: 01 - Priority preferred
port 0x2f8-0x2f8, align 0x0, size 0x8, 16-bit address decoding irq 3 High-Edge
Dependent: 02 - Priority preferred
port 0x2e8-0x2e8, align 0x0, size 0x8, 16-bit address decoding irq 3 High-Edge
Dependent: 03 - Priority preferred
port 0x3f8-0x3f8, align 0x0, size 0x8, 16-bit address decoding irq 4 High-Edge
Dependent: 04 - Priority preferred
port 0x3e8-0x3e8, align 0x0, size 0x8, 16-bit address decoding irq 4 High-Edge
Dependent: 05 - Priority functional
port 0x100-0x3f8, align 0x7, size 0x8, 16-bit address decoding irq 1,3,4,5,6,7,8,10,11,12,13,14,15 High-Edge
00:00 PNP0c02 (unknown)
state = active
allocated resources:
io 0x370-0x371
io 0xea-0xeb
mem 0xfffc0000-0xffffffff00:01 PNP0c01 (unknown)
state = active
allocated resources:
mem 0x0-0x9ffff
mem 0xe4000-0xfffff
mem 0x100000-0x5ffffff
mem 0xfff80000-0xfffbffff00:02 PNP0200 (unknown)
state = active
allocated resources:
io 0x0-0xf
io 0x81-0x8f
io 0xc0-0xdf
dma 400:03 PNP0000 (unknown)
state = active
allocated resources:
io 0x20-0x21
io 0xa0-0xa1
irq 200:04 PNP0100 (unknown)
state = active
allocated resources:
io 0x40-0x43
irq 0
00:05 PNP0b00 (unknown)
state = active
allocated resources:
io 0x70-0x71
irq 8
00:06 PNP0303 (unknown)
state = active
allocated resources:
io 0x60-0x60
io 0x64-0x64
irq 100:07 PNP0c04 (unknown)
state = active
allocated resources:
io 0xf0-0xff
irq 1300:08 PNP0800 (unknown)
state = active
allocated resources:
io 0x61-0x61
00:09 PNP0a03 (unknown)
state = active
allocated resources:
io 0xcf8-0xcff
00:0a PNP0c02 (unknown)
state = active
allocated resources:
io 0x4d0-0x4d1
io 0x8000-0x803f
io 0x7000-0x700f00:0b PNP0c02 (unknown)
state = active
allocated resources:
mem 0xe0000-0xe3fff
00:0c PNP0c02 (unknown)
state = disabled
00:0d PNP0f13 (unknown)
state = active
allocated resources:
irq 12
possible resources:
irq 12 High-Edge
00:0e PNP0501 (unknown)
state = active
allocated resources:
io 0x3f8-0x3ff
irq 4
possible resources:
Dependent: 01 - Priority acceptable
port 0x3f8-0x3f8, align 0x7, size 0x8, 16-bit address decoding irq 4 High-Edge
Dependent: 02 - Priority acceptable
port 0x2f8-0x2f8, align 0x7, size 0x8, 16-bit address decoding irq 3 High-Edge
Dependent: 03 - Priority acceptable
port 0x3e8-0x3e8, align 0x7, size 0x8, 16-bit address decoding irq 4 High-Edge
Dependent: 04 - Priority acceptable
port 0x2e8-0x2e8, align 0x7, size 0x8, 16-bit address decoding irq 3 High-Edge
Dependent: 05 - Priority acceptable
port 0x3f8-0x3f8, align 0x7, size 0x8, 16-bit address decoding irq 3 High-Edge
Dependent: 06 - Priority acceptable
port 0x2f8-0x2f8, align 0x7, size 0x8, 16-bit address decoding irq 4 High-Edge
Dependent: 07 - Priority acceptable
port 0x3e8-0x3e8, align 0x7, size 0x8, 16-bit address decoding irq 3 High-Edge
Dependent: 08 - Priority acceptable
port 0x2e8-0x2e8, align 0x7, size 0x8, 16-bit address decoding irq 4 High-Edge
00:11 PNP0700 (unknown)
state = active
allocated resources:
io 0x3f0-0x3f5
io 0x3f7-0x3f7
irq 6
dma 2
possible resources:
Dependent: 01 - Priority acceptable
port 0x3f0-0x3f0, align 0x7, size 0x6, 16-bit address decoding port 0x3f7-0x3f7, align 0x0, size 0x1, 16-bit address decoding irq 6 High-Edge
dma 2 8-bit compatible
Dependent: 02 - Priority acceptable
port 0x370-0x370, align 0x7, size 0x6, 16-bit address decoding port 0x377-0x377, align 0x0, size 0x1, 16-bit address decoding irq 6 High-Edge
dma 2 8-bit compatible
00:15 PNP0400 (unknown)
state = active
allocated resources:
io 0x378-0x37f
irq 7
possible resources:
Dependent: 01 - Priority acceptable
port 0x378-0x378, align 0x7, size 0x8, 16-bit address decoding irq 7 High-Edge
Dependent: 02 - Priority acceptable
port 0x278-0x278, align 0x7, size 0x8, 16-bit address decoding irq 5 High-Edge
Dependent: 03 - Priority acceptable
port 0x228-0x228, align 0x7, size 0x8, 16-bit address decoding irq 7 High-Edge
Dependent: 04 - Priority acceptable
port 0x378-0x378, align 0x7, size 0x8, 16-bit address decoding irq 5 High-Edge
Dependent: 05 - Priority acceptable
port 0x278-0x278, align 0x7, size 0x8, 16-bit address decoding irq 7 High-Edge
Dependent: 06 - Priority acceptable
port 0x228-0x228, align 0x7, size 0x8, 16-bit address decoding irq 5 High-Edge
Quoted 12 lines · Martin Doucha
Quoted 11 lines · Bjorn Helgaas
Thanks very much for the report. This sounds like it could be a PNPACPI issue, which I am very interested in fixing.
Can you please turn on
CONFIG_PNP_DEBUGin your .config and collect the complete dmesg log with and without "pnpacpi=off"?I do have an "lspnp" that works with PNPACPI here:
http://kernel.org/pub/linux/kernel/people/helgaas/pnputils-0.1.tar.bz2
but it's not widely used. The debug information from the config option above is usually more useful.
Quoted 6 lines
Quoted 1 line
Bjorn
I'm sorry it took me so long, here's the output of lspnp -vvv from both PNPBIOS and ACPI PnP (same kernel, the only difference is pnpacpi=off boot argument). I can't find any mention of my parallel port in ACPI PnP output but it's the last listed device (00:15 PNP0400) in PNPBIOS output.
I don't see the parallel port either. Can you please open a bugzilla for this and attach the complete dmesg log and the ACPI table dump using the instructions here:
http://kernel.org/pub/linux/kernel/people/helgaas/debug
You can put it in the Drivers/PNP category and add me to the cc:
list.
I assume the parallel port has *never* worked with ACPI enabled, right?
Bjorn
http://bugzilla.kernel.org/show_bug.cgi?id=11603
Thanks for opening this bug report, Martin.
The DSDT definitely includes the parallel device. The device can be in several modes, so there are actually three sections for it: LPT, EPP, and ECP. None of them showed up in the PNP debug output, so the _STA methods must be telling us the device isn't present at all.
If you turn on CONFIG_ACPI_DEBUG and boot with these options:
acpi.debug_layer=0x10000 acpi.debug_level=0x10
we should see the results of evaluating _STA.
Does the BIOS setup screen have any config items related to the parallel port? If so, can you experiment with them and find out whether they make any difference?
Your logs are perfect, which makes me happy because it's the first time I've successfully used the byzantine ACPI debug infrastructure.
Quoted 3 lines
Log with parport set to auto/bidirectional in BIOS for comparison. PNPBIOS does detect it in this setting, ACPI doesn't. Same with auto/EPP which I used until now.
I think this is a BIOS defect.
When you set the port to "enabled" in the BIOS, Linux finds and uses the parallel port with no problem.
When you set the port to "auto/bidirectional" or "auto/EPP" in the BIOS, the _STA methods on all the parallel devices return 0:
bus-0117 [00] bus_get_status : Device [LPT] status [00000000]
bus-0117 [00] bus_get_status : Device [EPP] status [00000000]
bus-0117 [00] bus_get_status : Device [ECP] status [00000000]A zero _STA means the device is not present at all, so I think Linux is right to ignore the devices.
I suppose we could try to add a quirk to Linux to work around this, but I'm not sure whether it's worth it. Your machine is from 1998, and some distros blacklist ACPI on old machines because it's not worth the trouble to fix all of them.
Some drivers will blindly probe for hardware if PNP doesn't report anything. Is parport one of them, i.e., if you load it by hand, does it work?
Quoted 15 lines · Bjorn Helgaas
Your logs are perfect, which makes me happy because it's the first time I've successfully used the byzantine ACPI debug infrastructure.
Quoted 3 lines
Log with parport set to auto/bidirectional in BIOS for comparison. PNPBIOS does detect it in this setting, ACPI doesn't. Same with auto/EPP which I used until now.
I think this is a BIOS defect.
When you set the port to "enabled" in the BIOS, Linux finds and uses the parallel port with no problem.
When you set the port to "auto/bidirectional" or "auto/EPP" in the BIOS, the
_STAmethods on all the parallel devices return 0:
Quoted 7 lines
bus-0117 [00] bus_get_status : Device [LPT] status [00000000] bus-0117 [00] bus_get_status : Device [EPP] status [00000000] bus-0117 [00] bus_get_status : Device [ECP] status [00000000]A zero
_STAmeans the device is not present at all, so I think Linux is right to ignore the devices.
If you want you could try to run the attached program on your pc in "auto/bidirectional" or "auto/EPP" mode.
This program does what _STA methods do.
Matthieu
#include <sys/io.h>
#define S707 0x0370
#define INDX S707
#define DATA S707+1
int R707(int Arg0)
{
int ret;
outb(0x55,INDX);
outb(0x55,INDX);
outb(Arg0,INDX);
ret = inb(DATA);
outb(0xAA,INDX);
return ret;
}
void W707(int Arg0, int Arg1)
{
outb(0x55,INDX);
outb(0x55,INDX);
outb(Arg0,INDX);
outb(Arg1, DATA);
outb(0xAA,INDX);
}int GSTA()
{
int ret;
W707 (0x07, 0x03);
ret = R707 (0xF0);
printf("raw %d\n", ret);
printf("LPT %d\n", (ret & 0x7) == 0);
printf("EPP %d\n", (ret & 0x3) == 1);
printf("ECP %d\n", (ret & 0x2) == 2);
return ret;
}int main()
{
iopl(3);
GSTA();
return 0;
}Quoted 4 lines
If you want you could try to run the attached program on your pc in "auto/bidirectional" or "auto/EPP" mode.
This program does what
_STAmethods do.
I'm just curious -- what do you hope to learn from this program? Do you think it will tell us more than what actually running _STA did?
The best solution I can think of would be to have a parameter like "parport.nopnp" that made parport just probe the legacy addresses, and document that you might need that on machines with broken ACPI firmware. But I'm a little afraid to touch parport_pc.c.
Quoted 8 lines · Bjorn Helgaas
Quoted 3 lines
If you want you could try to run the attached program on your pc in "auto/bidirectional" or "auto/EPP" mode.
This program does what
_STAmethods do.I'm just curious -- what do you hope to learn from this program? Do you think it will tell us more than what actually running
_STAdid?
Yes I was curious of the value before the mask : some of the mask and comparaison look strange.
Quoted 4 lines
The best solution I can think of would be to have a parameter like "parport.nopnp" that made parport just probe the legacy addresses, and document that you might need that on machines with broken ACPI firmware. But I'm a little afraid to touch
parport_pc.c.
Aren't parport still probing it's own port if pnp failed ?
Matthieu
Quoted 1 line
Aren't parport still probing it's own port if pnp failed ?
Could be; I haven't looked. I just assumed parport didn't do the legacy probe because Martin reported that the port didn't work when PNPACPI was enabled.
And I retract my "parport.nopnp" idea. A positive statement like "parport.legacy" or something along the lines of "look here" would be better. It's safe to use PNP to probe; it just won't find anything. All we want is something to tell parport to do the legacy probe in addition.