Skip to contentSkip to conversation

NAND: Add panic_write for NAND flashes

PATCH In review Edgar E. Iglesias 2 participants 2 messages Sep 23, 2008 – Aug 18, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 NAND: Add panic_write for NAND flashes

Hello,

This is a quick and dirty patch to add panic_write for NAND flashes. The patch seems to work OK on my CRIS board running a 2.6.26 kernel with a ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit). Also compile tested on a fresh x86 MTD git clone.

If you find it useful feel free to apply it, otherwise >/dev/null.

Thanks,

 drivers/mtd/nand/nand_base.c |  129 +++++++++++++++++++++++++++++++++++++++---
 1 files changed, 121 insertions(+), 8 deletions(-)
drivers/mtd/nand/nand_base.c +121 -8
index 0a9c9cd..442a7de 100644
@@ -414,6 +414,28 @@ static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip,
 	return nand_isbad_bbt(mtd, ofs, allowbbt);
 }
 
+/**
+ * panic_nand_wait_ready - [GENERIC] Wait for the ready pin after commands.
+ * @mtd:	MTD device structure
+ * @timeo:	Timeout
+ *
+ * Helper function for nand_wait_ready used when needing to wait in interrupt
+ * context.
+ */
+static void panic_nand_wait_ready(struct mtd_info *mtd, unsigned long timeo)
+{
+	struct nand_chip *chip = mtd->priv;
+	int i;
+
+	/* Give the device 400 ms to get ready?	 */
+	for (i = 0; i < timeo; i++) {
+		if (chip->dev_ready(mtd))
+			break;
+		touch_softlockup_watchdog();
+		mdelay(1);
+	}
+}
+
 /*
  * Wait for the ready pin, after a command
  * The timeout is catched later.
@@ -423,6 +445,10 @@ void nand_wait_ready(struct mtd_info *mtd)
 	struct nand_chip *chip = mtd->priv;
 	unsigned long timeo = jiffies + 2;
 
+	/* 400ms timeout?  */
+	if (in_interrupt())
+		return panic_nand_wait_ready(mtd, 400);
+
 	led_trigger_event(nand_led_trigger, LED_FULL);
 	/* wait until command is processed or timeout occures */
 	do {
@@ -658,6 +684,23 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
 }
 
 /**
+ * panic_nand_get_device - [GENERIC] Get chip for selected access
+ * @chip:	the nand chip descriptor
+ * @mtd:	MTD device structure
+ * @new_state:	the state which is requested
+ *
+ * Used when in panic, no locks are taken.
+ */
+static void
+panic_nand_get_device(struct nand_chip *chip,
+		      struct mtd_info *mtd, int new_state)
+{
+	/* Hardware controller shared among independend devices */
+	chip->controller->active = chip;
+	chip->state = new_state;
+}
+
+/**
  * nand_get_device - [GENERIC] Get chip for selected access
  * @chip:	the nand chip descriptor
  * @mtd:	MTD device structure
@@ -697,6 +740,32 @@ nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state)
 }
 
 /**
+ * panic_nand_wait - [GENERIC]  wait until the command is done
+ * @mtd:	MTD device structure
+ * @chip:	NAND chip structure
+ * @timeo:	Timeout
+ *
+ * Wait for command done. This is a helper function for nand_wait used when
+ * we are in interrupt context. May happen when in panic and trying to write
+ * an oops trough mtdoops.
+ */
+static void panic_nand_wait(struct mtd_info *mtd, struct nand_chip *chip,
+			    unsigned long timeo)
+{
+	int i;
+	for (i = 0; i < timeo; i++) {
+		if (chip->dev_ready) {
+			if (chip->dev_ready(mtd))
+				break;
+		} else {
+			if (chip->read_byte(mtd) & NAND_STATUS_READY)
+				break;
+		}
+		mdelay(1);
+        }
+}
+
+/**
  * nand_wait - [DEFAULT]  wait until the command is done
  * @mtd:	MTD device structure
  * @chip:	NAND chip structure
@@ -727,15 +796,19 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
 	else
 		chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
 
-	while (time_before(jiffies, timeo)) {
-		if (chip->dev_ready) {
-			if (chip->dev_ready(mtd))
-				break;
-		} else {
-			if (chip->read_byte(mtd) & NAND_STATUS_READY)
-				break;
+	if (in_interrupt())
+		panic_nand_wait(mtd, chip, timeo);
+	else {
+		while (time_before(jiffies, timeo)) {
+			if (chip->dev_ready) {
+				if (chip->dev_ready(mtd))
+					break;
+			} else {
+				if (chip->read_byte(mtd) & NAND_STATUS_READY)
+					break;
+			}
+			cond_resched();
 		}
-		cond_resched();
 	}
 	led_trigger_event(nand_led_trigger, LED_OFF);
 
@@ -1797,6 +1870,45 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
 }
 
 /**
+ * panic_nand_write - [MTD Interface] NAND write with ECC
+ * @mtd:	MTD device structure
+ * @to:		offset to write to
+ * @len:	number of bytes to write
+ * @retlen:	pointer to variable to store the number of written bytes
+ * @buf:	the data to write
+ *
+ * NAND write with ECC. Used when performing writes in interrupt context, this
+ * may for example be called by mtdoops when writing an oops while in panic.
+ */
+static int panic_nand_write(struct mtd_info *mtd, loff_t to, size_t len,
+			    size_t *retlen, const uint8_t *buf)
+{
+	struct nand_chip *chip = mtd->priv;
+	int ret;
+
+	/* Do not allow reads past end of device */
+	if ((to + len) > mtd->size)
+		return -EINVAL;
+	if (!len)
+		return 0;
+
+	/* Wait for the device to get ready.  */
+	panic_nand_wait(mtd, chip, 400);
+
+	/* Grab the device.  */
+	panic_nand_get_device(chip, mtd, FL_WRITING);
+
+	chip->ops.len = len;
+	chip->ops.datbuf = (uint8_t *)buf;
+	chip->ops.oobbuf = NULL;
+
+	ret = nand_do_write_ops(mtd, to, &chip->ops);
+
+	*retlen = chip->ops.retlen;
+	return ret;
+}
+
+/**
  * nand_write - [MTD Interface] NAND write with ECC
  * @mtd:	MTD device structure
  * @to:		offset to write to
@@ -2694,6 +2806,7 @@ int nand_scan_tail(struct mtd_info *mtd)
 	mtd->unpoint = NULL;
 	mtd->read = nand_read;
 	mtd->write = nand_write;
+	mtd->panic_write = panic_nand_write;
 	mtd->read_oob = nand_read_oob;
 	mtd->write_oob = nand_write_oob;
 	mtd->sync = nand_sync;
#1 lore raw

why this patch is not accepted?

Thanks

Janboe Ye

2008/9/23 Edgar E. Iglesias <[email protected]>:

Quoted 204 lines

Hello,

This is a quick and dirty patch to add panic_write for NAND flashes. The patch seems to work OK on my CRIS board running a 2.6.26 kernel with a ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit). Also compile tested on a fresh x86 MTD git clone.

If you find it useful feel free to apply it, otherwise >/dev/null.

Thanks,

 drivers/mtd/nand/nand_base.c |  129 +++++++++++++++++++++++++++++++++++++++---

 1 files changed, 121 insertions(+), 8 deletions(-)
drivers/mtd/nand/nand_base.c +69 -0
index 0a9c9cd..442a7de 100644
@@ -414,6 +414,28 @@ static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip,
        return nand_isbad_bbt(mtd, ofs, allowbbt);
  }
 
+/**
+ * panic_nand_wait_ready - [GENERIC] Wait for the ready pin after commands.
+ * @mtd:       MTD device structure
+ * @timeo:     Timeout
+ *
+ * Helper function for nand_wait_ready used when needing to wait in interrupt
+ * context.
+ */
+static void panic_nand_wait_ready(struct mtd_info *mtd, unsigned long timeo)
+{
+       struct nand_chip *chip = mtd->priv;
+       int i;
+
+       /* Give the device 400 ms to get ready?  */
+       for (i = 0; i < timeo; i++) {
+               if (chip->dev_ready(mtd))
+                       break;
+               touch_softlockup_watchdog();
+               mdelay(1);
+       }
+}
+
  /*
  * Wait for the ready pin, after a command
  * The timeout is catched later.
@@ -423,6 +445,10 @@ void nand_wait_ready(struct mtd_info *mtd)
        struct nand_chip *chip = mtd->priv;
        unsigned long timeo = jiffies + 2;
 
+       /* 400ms timeout?  */
+       if (in_interrupt())
+               return panic_nand_wait_ready(mtd, 400);
+
        led_trigger_event(nand_led_trigger, LED_FULL);
        /* wait until command is processed or timeout occures */
        do {
@@ -658,6 +684,23 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
  }
 
  /**
+ * panic_nand_get_device - [GENERIC] Get chip for selected access
+ * @chip:      the nand chip descriptor
+ * @mtd:       MTD device structure
+ * @new_state: the state which is requested
+ *
+ * Used when in panic, no locks are taken.
+ */
+static void
+panic_nand_get_device(struct nand_chip *chip,
+                     struct mtd_info *mtd, int new_state)
+{
+       /* Hardware controller shared among independend devices */
+       chip->controller->active = chip;
+       chip->state = new_state;
+}
+
+/**
  * nand_get_device - [GENERIC] Get chip for selected access
  * @chip:      the nand chip descriptor
  * @mtd:       MTD device structure
@@ -697,6 +740,32 @@ nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state)
  }
 
  /**
+ * panic_nand_wait - [GENERIC]  wait until the command is done
+ * @mtd:       MTD device structure
+ * @chip:      NAND chip structure
+ * @timeo:     Timeout
+ *
+ * Wait for command done. This is a helper function for nand_wait used when
+ * we are in interrupt context. May happen when in panic and trying to write
+ * an oops trough mtdoops.
+ */
+static void panic_nand_wait(struct mtd_info *mtd, struct nand_chip *chip,
+                           unsigned long timeo)
+{
+       int i;
+       for (i = 0; i < timeo; i++) {
+               if (chip->dev_ready) {
+                       if (chip->dev_ready(mtd))
+                               break;
+               } else {
+                       if (chip->read_byte(mtd) & NAND_STATUS_READY)
+                               break;
+               }
+               mdelay(1);
+        }
+}
+
+/**
  * nand_wait - [DEFAULT]  wait until the command is done
  * @mtd:       MTD device structure
  * @chip:      NAND chip structure
@@ -727,15 +796,19 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)

       else
               chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);

-       while (time_before(jiffies, timeo)) {
-               if (chip->dev_ready) {
-                       if (chip->dev_ready(mtd))
-                               break;
-               } else {
-                       if (chip->read_byte(mtd) & NAND_STATUS_READY)
-                               break;
+       if (in_interrupt())
+               panic_nand_wait(mtd, chip, timeo);
+       else {
+               while (time_before(jiffies, timeo)) {
+                       if (chip->dev_ready) {
+                               if (chip->dev_ready(mtd))
+                                       break;
+                       } else {
+                               if (chip->read_byte(mtd) & NAND_STATUS_READY)
+                                       break;
+                       }
+                       cond_resched();
               }
-               cond_resched();
       }
       led_trigger_event(nand_led_trigger, LED_OFF);

drivers/mtd/nand/nand_base.c +40 -0
@@ -1797,6 +1870,45 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
  }
 
  /**
+ * panic_nand_write - [MTD Interface] NAND write with ECC
+ * @mtd:       MTD device structure
+ * @to:                offset to write to
+ * @len:       number of bytes to write
+ * @retlen:    pointer to variable to store the number of written bytes
+ * @buf:       the data to write
+ *
+ * NAND write with ECC. Used when performing writes in interrupt context, this
+ * may for example be called by mtdoops when writing an oops while in panic.
+ */
+static int panic_nand_write(struct mtd_info *mtd, loff_t to, size_t len,
+                           size_t *retlen, const uint8_t *buf)
+{
+       struct nand_chip *chip = mtd->priv;
+       int ret;
+
+       /* Do not allow reads past end of device */
+       if ((to + len) > mtd->size)
+               return -EINVAL;
+       if (!len)
+               return 0;
+
+       /* Wait for the device to get ready.  */
+       panic_nand_wait(mtd, chip, 400);
+
+       /* Grab the device.  */
+       panic_nand_get_device(chip, mtd, FL_WRITING);
+
+       chip->ops.len = len;
+       chip->ops.datbuf = (uint8_t *)buf;
+       chip->ops.oobbuf = NULL;
+
+       ret = nand_do_write_ops(mtd, to, &chip->ops);
+
+       *retlen = chip->ops.retlen;
+       return ret;
+}
+
+/**
  * nand_write - [MTD Interface] NAND write with ECC
  * @mtd:       MTD device structure
  * @to:                offset to write to
@@ -2694,6 +2806,7 @@ int nand_scan_tail(struct mtd_info *mtd)
        mtd->unpoint = NULL;
        mtd->read = nand_read;
        mtd->write = nand_write;
+       mtd->panic_write = panic_nand_write;
        mtd->read_oob = nand_read_oob;
        mtd->write_oob = nand_write_oob;
        mtd->sync = nand_sync;

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/