Skip to contentSkip to conversation

new hwmon driver adt7462

PATCH In review Darrick J. Wong 2 participants 2 messages Oct 1, 2008

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 new hwmon driver adt7462

New driver to feed on. As Jean mentioned a couple of years ago, this chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13 voltage sensors. This driver has been tested on an IntelliStation Z30.

---

 Documentation/hwmon/adt7462 |   67 +
 drivers/hwmon/Kconfig       |   10 
 drivers/hwmon/Makefile      |    1 
 drivers/hwmon/adt7462.c     | 1991 +++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 2069 insertions(+), 0 deletions(-)
Documentation/hwmon/adt7462 new file +67 -0
new file mode 100644
index 0000000..488e5ca
@@ -0,0 +1,67 @@
+Kernel driver adt7462
+======================
+
+Supported chips:
+  * Analog Devices ADT7462
+    Prefix: 'adt7462'
+    Addresses scanned: I2C 0x58, 0x5C
+    Datasheet: Publicly available at the Analog Devices website
+
+Author: Darrick J. Wong
+
+Description
+-----------
+
+This driver implements support for the Analog Devices ADT7462 chip family.
+
+This chip is a bit of a beast.  It has 8 counters for measuring fan speed.  It
+can also measure 13 voltages or 4 temperatures, or various combinations of the
+two.  See the chip documentation for more details about the exact set of
+configurations.  This driver does not allow one to configure the chip; that is
+left to the system designer.
+
+A sophisticated control system for the PWM outputs is designed into the ADT7462
+that allows fan speed to be adjusted automatically based on any of the three
+temperature sensors. Each PWM output is individually adjustable and
+programmable. Once configured, the ADT7462 will adjust the PWM outputs in
+response to the measured temperatures without further host intervention.  This
+feature can also be disabled for manual control of the PWM's.
+
+Each of the measured inputs (voltage, temperature, fan speed) has
+corresponding high/low limit values. The ADT7462 will signal an ALARM if
+any measured value exceeds either limit.
+
+The ADT7462 samples all inputs continuously. The driver will not read
+the registers more often than once every other second. Further,
+configuration data is only read once per minute.
+
+Special Features
+----------------
+
+The ADT7462 have a 10-bit ADC and can therefore measure temperatures
+with 0.25 degC resolution.
+
+The Analog Devices datasheet is very detailed and describes a procedure for
+determining an optimal configuration for the automatic PWM control.
+
+The driver will report sensor labels when it is able to determine that
+information from the configuration registers.
+
+Configuration Notes
+-------------------
+
+Besides standard interfaces driver adds the following:
+
+* PWM Control
+
+* pwm#_auto_point1_pwm and pwm#_auto_point1_temp and
+* pwm#_auto_point2_pwm and pwm#_auto_point2_temp -
+
+point1: Set the pwm speed at a lower temperature bound.
+point2: Set the pwm speed at a higher temperature bound.
+
+The ADT7462 will scale the pwm between the lower and higher pwm speed when
+the temperature is between the two temperature boundaries.  PWM values range
+from 0 (off) to 255 (full speed).  Fan speed will be set to maximum when the
+temperature sensor associated with the PWM control exceeds temp#_max.
+
drivers/hwmon/Kconfig +10 -0
index 6d91cee..a36e2bb 100644
@@ -159,6 +159,16 @@ config SENSORS_ADM9240
 	  This driver can also be built as a module.  If so, the module
 	  will be called adm9240.
 
+config SENSORS_ADT7462
+	tristate "Analog Devices ADT7462"
+	depends on I2C && EXPERIMENTAL
+	help
+	  If you say yes here you get support for the Analog Devices
+	  ADT7462 temperature monitoring chips.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called adt7462.
+
 config SENSORS_ADT7470
 	tristate "Analog Devices ADT7470"
 	depends on I2C && EXPERIMENTAL
drivers/hwmon/Makefile +1 -0
index 950134a..836b277 100644
@@ -25,6 +25,7 @@ obj-$(CONFIG_SENSORS_ADM1029)	+= adm1029.o
 obj-$(CONFIG_SENSORS_ADM1031)	+= adm1031.o
 obj-$(CONFIG_SENSORS_ADM9240)	+= adm9240.o
 obj-$(CONFIG_SENSORS_ADS7828)	+= ads7828.o
+obj-$(CONFIG_SENSORS_ADT7462)	+= adt7462.o
 obj-$(CONFIG_SENSORS_ADT7470)	+= adt7470.o
 obj-$(CONFIG_SENSORS_ADT7473)	+= adt7473.o
 obj-$(CONFIG_SENSORS_APPLESMC)	+= applesmc.o
drivers/hwmon/adt7462.c new file +1991 -0

1,991 lines not on this page · raw message

#1 lore raw

Hi Darrick,

Quoted 5 lines · Darrick J. Wong

New driver to feed on. As Jean mentioned a couple of years ago, this chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13 voltage sensors. This driver has been tested on an IntelliStation Z30.

Quoted 8 lines

---

 Documentation/hwmon/adt7462 |   67 +
 drivers/hwmon/Kconfig       |   10 
 drivers/hwmon/Makefile      |    1 
 drivers/hwmon/adt7462.c     | 1991 +++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 2069 insertions(+), 0 deletions(-)

Two years ago, Eric Olsen (Cc'd) asked for support for this device and even said he would write the driver himself. We didn't hear from him since then. Now that we have a driver, maybe Eric can help testing it and maybe even reviewing it?

I clearly do not have the time for this myself (not on my free time, at least.)

Signature · 6 lines
Jean Delvare

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors