2.6.27-stable review

@@ -2996,8 +2996,8 @@ static void fbcon_set_all_vcs(struct fb_
 		p = &fb_display[vc->vc_num];
 		set_blitting_type(vc, info);
 		var_to_display(p, &info->var, info);
-		cols = FBCON_SWAP(p->rotate, info->var.xres, info->var.yres);
-		rows = FBCON_SWAP(p->rotate, info->var.yres, info->var.xres);
+		cols = FBCON_SWAP(ops->rotate, info->var.xres, info->var.yres);
+		rows = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres);
 		cols /= vc->vc_font.width;
 		rows /= vc->vc_font.height;
 		vc_resize(vc, cols, rows);

@@ -1173,7 +1173,7 @@ static void free_notes_attrs(struct modu
 		while (i-- > 0)
 			sysfs_remove_bin_file(notes_attrs->dir,
 					      &notes_attrs->attrs[i]);
-		kobject_del(notes_attrs->dir);
+		kobject_put(notes_attrs->dir);
 	}
 	kfree(notes_attrs);
 }

@@ -1243,7 +1243,7 @@ struct device *device_create_vargs(struc
 	return dev;
 
 error:
-	kfree(dev);
+	put_device(dev);
 	return ERR_PTR(retval);
 }
 EXPORT_SYMBOL_GPL(device_create_vargs);

@@ -523,11 +523,16 @@ static void klist_children_put(struct kl
  * device_initialize - init device structure.
  * @dev: device.
  *
- * This prepares the device for use by other layers,
- * including adding it to the device hierarchy.
+ * This prepares the device for use by other layers by initializing
+ * its fields.
  * It is the first half of device_register(), if called by
- * that, though it can also be called separately, so one
- * may use @dev's fields (e.g. the refcount).
+ * that function, though it can also be called separately, so one
+ * may use @dev's fields. In particular, get_device()/put_device()
+ * may be used for reference counting of @dev after calling this
+ * function.
+ *
+ * NOTE: Use put_device() to give up your reference instead of freeing
+ * @dev directly once you have called this function.
  */
 void device_initialize(struct device *dev)
 {

@@ -836,9 +841,13 @@ static void device_remove_sys_dev_entry(
  * This is part 2 of device_register(), though may be called
  * separately _iff_ device_initialize() has been called separately.
  *
- * This adds it to the kobject hierarchy via kobject_add(), adds it
+ * This adds @dev to the kobject hierarchy via kobject_add(), adds it
  * to the global and sibling lists for the device, then
  * adds it to the other relevant subsystems of the driver model.
+ *
+ * NOTE: _Never_ directly free @dev after calling this function, even
+ * if it returned an error! Always use put_device() to give up your
+ * reference instead.
  */
 int device_add(struct device *dev)
 {

@@ -965,6 +974,10 @@ done:
  * I.e. you should only call the two helpers separately if
  * have a clearly defined need to use and refcount the device
  * before it is added to the hierarchy.
+ *
+ * NOTE: _Never_ directly free @dev after calling this function, even
+ * if it returned an error! Always use put_device() to give up the
+ * reference initialized in this function instead.
  */
 int device_register(struct device *dev)
 {

@@ -1007,6 +1007,11 @@ static int ath9k_ampdu_action(struct iee
 	return ret;
 }
 
+static int ath9k_no_fragmentation(struct ieee80211_hw *hw, u32 value)
+{
+	return -EOPNOTSUPP;
+}
+
 static struct ieee80211_ops ath9k_ops = {
 	.tx 		    = ath9k_tx,
 	.start 		    = ath9k_start,

@@ -1031,7 +1036,8 @@ static struct ieee80211_ops ath9k_ops = 
 	.get_tsf 	    = ath9k_get_tsf,
 	.reset_tsf 	    = ath9k_reset_tsf,
 	.tx_last_beacon     = NULL,
-	.ampdu_action       = ath9k_ampdu_action
+	.ampdu_action       = ath9k_ampdu_action,
+	.set_frag_threshold = ath9k_no_fragmentation,
 };
 
 void ath_get_beaconconfig(struct ath_softc *sc,

@@ -804,7 +804,7 @@ static int ieee80211_ioctl_siwfrag(struc
 	 * configure it here */
 
 	if (local->ops->set_frag_threshold)
-		local->ops->set_frag_threshold(
+		return local->ops->set_frag_threshold(
 			local_to_hw(local),
 			local->fragmentation_threshold);
 

@@ -2109,8 +2109,6 @@ rdev_size_store(mdk_rdev_t *rdev, const 
 
 	if (strict_strtoull(buf, 10, &size) < 0)
 		return -EINVAL;
-	if (size < my_mddev->size)
-		return -EINVAL;
 	if (my_mddev->pers && rdev->raid_disk >= 0) {
 		if (my_mddev->persistent) {
 			size = super_types[my_mddev->major_version].

@@ -2121,9 +2119,9 @@ rdev_size_store(mdk_rdev_t *rdev, const 
 			size = (rdev->bdev->bd_inode->i_size >> 10);
 			size -= rdev->data_offset/2;
 		}
-		if (size < my_mddev->size)
-			return -EINVAL; /* component must fit device */
 	}
+	if (size < my_mddev->size)
+		return -EINVAL; /* component must fit device */
 
 	rdev->size = size;
 	if (size > oldsize && my_mddev->external) {

@@ -1323,7 +1323,7 @@ xfs_fs_remount(
 	"XFS: mount option \"%s\" not supported for remount\n", p);
 			return -EINVAL;
 #else
-			return 0;
+			break;
 #endif
 		}
 	}

@@ -316,7 +316,7 @@ void ath_descdma_cleanup(struct ath_soft
 #define ATH_RX_TIMEOUT           40      /* 40 milliseconds */
 #define WME_NUM_TID              16
 #define IEEE80211_BAR_CTL_TID_M  0xF000  /* tid mask */
-#define IEEE80211_BAR_CTL_TID_S  2       /* tid shift */
+#define IEEE80211_BAR_CTL_TID_S  12      /* tid shift */
 
 enum ATH_RX_TYPE {
 	ATH_RX_NON_CONSUMED = 0,

@@ -362,18 +362,23 @@ static int ohci_root_hub_state_changes(s
 		int any_connected)
 {
 	int	poll_rh = 1;
-	int	rhsc;
+	int	rhsc_status, rhsc_enable;
 
-	rhsc = ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC;
-	switch (ohci->hc_control & OHCI_CTRL_HCFS) {
+	/* Some broken controllers never turn off RHCS in the interrupt
+	 * status register.  For their sake we won't re-enable RHSC
+	 * interrupts if the interrupt bit is already active.
+	 */
+	rhsc_status = ohci_readl(ohci, &ohci->regs->intrstatus) &
+			OHCI_INTR_RHSC;
+	rhsc_enable = ohci_readl(ohci, &ohci->regs->intrenable) &
+			OHCI_INTR_RHSC;
 
+	switch (ohci->hc_control & OHCI_CTRL_HCFS) {
 	case OHCI_USB_OPER:
-		/* If no status changes are pending, enable status-change
-		 * interrupts.
-		 */
-		if (!rhsc && !changed) {
-			rhsc = OHCI_INTR_RHSC;
-			ohci_writel(ohci, rhsc, &ohci->regs->intrenable);
+		/* If no status changes are pending, enable RHSC interrupts. */
+		if (!rhsc_enable && !rhsc_status && !changed) {
+			rhsc_enable = OHCI_INTR_RHSC;
+			ohci_writel(ohci, rhsc_enable, &ohci->regs->intrenable);
 		}
 
 		/* Keep on polling until we know a device is connected

@@ -383,7 +388,7 @@ static int ohci_root_hub_state_changes(s
 			if (any_connected ||
 					!device_may_wakeup(&ohci_to_hcd(ohci)
 						->self.root_hub->dev)) {
-				if (rhsc)
+				if (rhsc_enable)
 					poll_rh = 0;
 			} else {
 				ohci->autostop = 1;

@@ -396,34 +401,36 @@ static int ohci_root_hub_state_changes(s
 				ohci->autostop = 0;
 				ohci->next_statechange = jiffies +
 						STATECHANGE_DELAY;
-			} else if (rhsc && time_after_eq(jiffies,
+			} else if (time_after_eq(jiffies,
 						ohci->next_statechange)
 					&& !ohci->ed_rm_list
 					&& !(ohci->hc_control &
 						OHCI_SCHED_ENABLES)) {
 				ohci_rh_suspend(ohci, 1);
-				poll_rh = 0;
+				if (rhsc_enable)
+					poll_rh = 0;
 			}
 		}
 		break;
 
-	/* if there is a port change, autostart or ask to be resumed */
 	case OHCI_USB_SUSPEND:
 	case OHCI_USB_RESUME:
+		/* if there is a port change, autostart or ask to be resumed */
 		if (changed) {
 			if (ohci->autostop)
 				ohci_rh_resume(ohci);
 			else
 				usb_hcd_resume_root_hub(ohci_to_hcd(ohci));
 		} else {
-			if (!rhsc && (ohci->autostop ||
+			if (!rhsc_enable && !rhsc_status && (ohci->autostop ||
 					ohci_to_hcd(ohci)->self.root_hub->
-						do_remote_wakeup))
-				ohci_writel(ohci, OHCI_INTR_RHSC,
+						do_remote_wakeup)) {
+				rhsc_enable = OHCI_INTR_RHSC;
+				ohci_writel(ohci, rhsc_enable,
 						&ohci->regs->intrenable);
-
-			/* everything is idle, no need for polling */
-			poll_rh = 0;
+			}
+			if (rhsc_enable)
+				poll_rh = 0;
 		}
 		break;
 	}

@@ -443,12 +450,16 @@ static inline int ohci_rh_resume(struct 
 static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
 		int any_connected)
 {
+	int	rhsc_status;
+
 	/* If RHSC is enabled, don't poll */
 	if (ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC)
 		return 0;
 
-	/* If no status changes are pending, enable status-change interrupts */
-	if (!changed) {
+	/* If no status changes are pending, enable RHSC interrupts */
+	rhsc_status = ohci_readl(ohci, &ohci->regs->intrstatus) &
+			OHCI_INTR_RHSC;
+	if (!changed && !rhsc_status) {
 		ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable);
 		return 0;
 	}

@@ -492,13 +503,6 @@ ohci_hub_status_data (struct usb_hcd *hc
 		length++;
 	}
 
-	/* Some broken controllers never turn off RHCS in the interrupt
-	 * status register.  For their sake we won't re-enable RHSC
-	 * interrupts if the flag is already set.
-	 */
-	if (ohci_readl(ohci, &ohci->regs->intrstatus) & OHCI_INTR_RHSC)
-		changed = 1;
-
 	/* look at each port */
 	for (i = 0; i < ohci->num_ports; i++) {
 		u32	status = roothub_portstatus (ohci, i);

@@ -359,17 +359,15 @@ static void ohci_finish_controller_resum
 
 /* Carry out polling-, autostop-, and autoresume-related state changes */
 static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
-		int any_connected)
+		int any_connected, int rhsc_status)
 {
 	int	poll_rh = 1;
-	int	rhsc_status, rhsc_enable;
+	int	rhsc_enable;
 
 	/* Some broken controllers never turn off RHCS in the interrupt
 	 * status register.  For their sake we won't re-enable RHSC
 	 * interrupts if the interrupt bit is already active.
 	 */
-	rhsc_status = ohci_readl(ohci, &ohci->regs->intrstatus) &
-			OHCI_INTR_RHSC;
 	rhsc_enable = ohci_readl(ohci, &ohci->regs->intrenable) &
 			OHCI_INTR_RHSC;
 

@@ -421,14 +419,23 @@ static int ohci_root_hub_state_changes(s
 				ohci_rh_resume(ohci);
 			else
 				usb_hcd_resume_root_hub(ohci_to_hcd(ohci));
+
+		/* If remote wakeup is disabled, stop polling */
+		} else if (!ohci->autostop &&
+				!ohci_to_hcd(ohci)->self.root_hub->
+					do_remote_wakeup) {
+			poll_rh = 0;
+
 		} else {
-			if (!rhsc_enable && !rhsc_status && (ohci->autostop ||
-					ohci_to_hcd(ohci)->self.root_hub->
-						do_remote_wakeup)) {
+			/* If no status changes are pending,
+			 * enable RHSC interrupts
+			 */
+			if (!rhsc_enable && !rhsc_status) {
 				rhsc_enable = OHCI_INTR_RHSC;
 				ohci_writel(ohci, rhsc_enable,
 						&ohci->regs->intrenable);
 			}
+			/* Keep polling until RHSC is enabled */
 			if (rhsc_enable)
 				poll_rh = 0;
 		}

@@ -448,22 +455,22 @@ static inline int ohci_rh_resume(struct 
  * autostop isn't used when CONFIG_PM is turned off.
  */
 static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
-		int any_connected)
+		int any_connected, int rhsc_status)
 {
-	int	rhsc_status;
-
 	/* If RHSC is enabled, don't poll */
 	if (ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC)
 		return 0;
 
-	/* If no status changes are pending, enable RHSC interrupts */
-	rhsc_status = ohci_readl(ohci, &ohci->regs->intrstatus) &
-			OHCI_INTR_RHSC;
-	if (!changed && !rhsc_status) {
-		ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable);
-		return 0;
-	}
-	return 1;
+	/* If status changes are pending, continue polling.
+	 * Conversely, if no status changes are pending but the RHSC
+	 * status bit was set, then RHSC may be broken so continue polling.
+	 */
+	if (changed || rhsc_status)
+		return 1;
+
+	/* It's safe to re-enable RHSC interrupts */
+	ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable);
+	return 0;
 }
 
 #endif	/* CONFIG_PM */

@@ -478,6 +485,7 @@ ohci_hub_status_data (struct usb_hcd *hc
 	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
 	int		i, changed = 0, length = 1;
 	int		any_connected = 0;
+	int		rhsc_status;
 	unsigned long	flags;
 
 	spin_lock_irqsave (&ohci->lock, flags);

@@ -503,6 +511,11 @@ ohci_hub_status_data (struct usb_hcd *hc
 		length++;
 	}
 
+	/* Clear the RHSC status flag before reading the port statuses */
+	ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrstatus);
+	rhsc_status = ohci_readl(ohci, &ohci->regs->intrstatus) &
+			OHCI_INTR_RHSC;
+
 	/* look at each port */
 	for (i = 0; i < ohci->num_ports; i++) {
 		u32	status = roothub_portstatus (ohci, i);

@@ -521,7 +534,7 @@ ohci_hub_status_data (struct usb_hcd *hc
 	}
 
 	hcd->poll_rh = ohci_root_hub_state_changes(ohci, changed,
-			any_connected);
+			any_connected, rhsc_status);
 
 done:
 	spin_unlock_irqrestore (&ohci->lock, flags);

@@ -1651,7 +1651,7 @@ int usb_gadget_register_driver(struct us
 		return -EBUSY;
 
 	if (!driver->bind || !driver->setup
-			|| driver->speed != USB_SPEED_FULL) {
+			|| driver->speed < USB_SPEED_FULL) {
 		printk(KERN_ERR "Invalid driver: bind %p setup %p speed %d\n",
 			driver->bind, driver->setup, driver->speed);
 		return -EINVAL;

@@ -81,6 +81,10 @@
 
 /*-------------------------------------------------------------------------*/
 
+/* Keep track of which host controller drivers are loaded */
+unsigned long usb_hcds_loaded;
+EXPORT_SYMBOL_GPL(usb_hcds_loaded);
+
 /* host controllers we manage */
 LIST_HEAD (usb_bus_list);
 EXPORT_SYMBOL_GPL (usb_bus_list);

@@ -482,4 +482,10 @@ static inline void usbmon_urb_complete(s
  */
 extern struct rw_semaphore ehci_cf_port_reset_rwsem;
 
+/* Keep track of which host controller drivers are loaded */
+#define USB_UHCI_LOADED		0
+#define USB_OHCI_LOADED		1
+#define USB_EHCI_LOADED		2
+extern unsigned long usb_hcds_loaded;
+
 #endif /* __KERNEL__ */

@@ -1049,6 +1049,12 @@ static int __init ehci_hcd_init(void)
 {
 	int retval = 0;
 
+	set_bit(USB_EHCI_LOADED, &usb_hcds_loaded);
+	if (test_bit(USB_UHCI_LOADED, &usb_hcds_loaded) ||
+			test_bit(USB_OHCI_LOADED, &usb_hcds_loaded))
+		printk(KERN_WARNING "Warning! ehci_hcd should always be loaded"
+				" before uhci_hcd and ohci_hcd, not after\n");
+
 	pr_debug("%s: block sizes: qh %Zd qtd %Zd itd %Zd sitd %Zd\n",
 		 hcd_name,
 		 sizeof(struct ehci_qh), sizeof(struct ehci_qtd),

@@ -1056,8 +1062,10 @@ static int __init ehci_hcd_init(void)
 
 #ifdef DEBUG
 	ehci_debug_root = debugfs_create_dir("ehci", NULL);
-	if (!ehci_debug_root)
-		return -ENOENT;
+	if (!ehci_debug_root) {
+		retval = -ENOENT;
+		goto err_debug;
+	}
 #endif
 
 #ifdef PLATFORM_DRIVER

@@ -1104,7 +1112,9 @@ clean0:
 #ifdef DEBUG
 	debugfs_remove(ehci_debug_root);
 	ehci_debug_root = NULL;
+err_debug:
 #endif
+	clear_bit(USB_EHCI_LOADED, &usb_hcds_loaded);
 	return retval;
 }
 module_init(ehci_hcd_init);

@@ -1126,6 +1136,7 @@ static void __exit ehci_hcd_cleanup(void
 #ifdef DEBUG
 	debugfs_remove(ehci_debug_root);
 #endif
+	clear_bit(USB_EHCI_LOADED, &usb_hcds_loaded);
 }
 module_exit(ehci_hcd_cleanup);
 

@@ -1098,6 +1098,7 @@ static int __init ohci_hcd_mod_init(void
 	printk (KERN_DEBUG "%s: " DRIVER_INFO "\n", hcd_name);
 	pr_debug ("%s: block sizes: ed %Zd td %Zd\n", hcd_name,
 		sizeof (struct ed), sizeof (struct td));
+	set_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
 
 #ifdef DEBUG
 	ohci_debug_root = debugfs_create_dir("ohci", NULL);

@@ -1184,6 +1185,7 @@ static int __init ohci_hcd_mod_init(void
  error_debug:
 #endif
 
+	clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
 	return retval;
 }
 module_init(ohci_hcd_mod_init);

@@ -1214,6 +1216,7 @@ static void __exit ohci_hcd_mod_exit(voi
 #ifdef DEBUG
 	debugfs_remove(ohci_debug_root);
 #endif
+	clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
 }
 module_exit(ohci_hcd_mod_exit);
 

@@ -953,6 +953,7 @@ static int __init uhci_hcd_init(void)
 
 	printk(KERN_INFO DRIVER_DESC " " DRIVER_VERSION "%s\n",
 			ignore_oc ? ", overcurrent ignored" : "");
+	set_bit(USB_UHCI_LOADED, &usb_hcds_loaded);
 
 	if (usb_disabled())
 		return -ENODEV;

@@ -988,6 +989,7 @@ debug_failed:
 
 errbuf_failed:
 
+	clear_bit(USB_UHCI_LOADED, &usb_hcds_loaded);
 	return retval;
 }
 

@@ -997,6 +999,7 @@ static void __exit uhci_hcd_cleanup(void
 	kmem_cache_destroy(uhci_up_cachep);
 	debugfs_remove(uhci_debugfs_root);
 	kfree(errbuf);
+	clear_bit(USB_UHCI_LOADED, &usb_hcds_loaded);
 }
 
 module_init(uhci_hcd_init);

@@ -873,6 +873,13 @@ struct net_device *gether_connect(struct
 		spin_lock(&dev->lock);
 		dev->port_usb = link;
 		link->ioport = dev;
+		if (netif_running(dev->net)) {
+			if (link->open)
+				link->open(link);
+		} else {
+			if (link->close)
+				link->close(link);
+		}
 		spin_unlock(&dev->lock);
 
 		netif_carrier_on(dev->net);

@@ -119,8 +119,8 @@ struct cppi {
 	void __iomem			*mregs;		/* Mentor regs */
 	void __iomem			*tibase;	/* TI/CPPI regs */
 
-	struct cppi_channel		tx[MUSB_C_NUM_EPT - 1];
-	struct cppi_channel		rx[MUSB_C_NUM_EPR - 1];
+	struct cppi_channel		tx[4];
+	struct cppi_channel		rx[4];
 
 	struct dma_pool			*pool;
 

@@ -30,6 +30,7 @@
 #include <linux/delay.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/gpio.h>
 
 #include <asm/arch/hardware.h>
 #include <asm/arch/memory.h>

@@ -39,7 +40,7 @@
 #include "musb_core.h"
 
 #ifdef CONFIG_MACH_DAVINCI_EVM
-#include <asm/arch/i2c-client.h>
+#define GPIO_nVBUS_DRV		87
 #endif
 
 #include "davinci.h"

@@ -138,7 +139,6 @@ static int vbus_state = -1;
 /* VBUS SWITCHING IS BOARD-SPECIFIC */
 
 #ifdef CONFIG_MACH_DAVINCI_EVM
-#ifndef CONFIG_MACH_DAVINCI_EVM_OTG
 
 /* I2C operations are always synchronous, and require a task context.
  * With unloaded systems, using the shared workqueue seems to suffice

@@ -146,12 +146,11 @@ static int vbus_state = -1;
  */
 static void evm_deferred_drvvbus(struct work_struct *ignored)
 {
-	davinci_i2c_expander_op(0x3a, USB_DRVVBUS, vbus_state);
+	gpio_set_value_cansleep(GPIO_nVBUS_DRV, vbus_state);
 	vbus_state = !vbus_state;
 }
 static DECLARE_WORK(evm_vbus_work, evm_deferred_drvvbus);
 
-#endif	/* modified board */
 #endif	/* EVM */
 
 static void davinci_source_power(struct musb *musb, int is_on, int immediate)

@@ -165,21 +164,10 @@ static void davinci_source_power(struct 
 
 #ifdef CONFIG_MACH_DAVINCI_EVM
 	if (machine_is_davinci_evm()) {
-#ifdef CONFIG_MACH_DAVINCI_EVM_OTG
-		/* modified EVM board switching VBUS with GPIO(6) not I2C
-		 * NOTE:  PINMUX0.RGB888 (bit23) must be clear
-		 */
-		if (is_on)
-			gpio_set(GPIO(6));
-		else
-			gpio_clear(GPIO(6));
-		immediate = 1;
-#else
 		if (immediate)
-			davinci_i2c_expander_op(0x3a, USB_DRVVBUS, !is_on);
+			gpio_set_value_cansleep(GPIO_nVBUS_DRV, vbus_state);
 		else
 			schedule_work(&evm_vbus_work);
-#endif
 	}
 #endif
 	if (immediate)

@@ -82,9 +82,9 @@
 /*
  * This gets many kinds of configuration information:
  *	- Kconfig for everything user-configurable
- *	- <asm/arch/hdrc_cnf.h> for SOC or family details
  *	- platform_device for addressing, irq, and platform_data
  *	- platform_data is mostly for board-specific informarion
+ *	  (plus recentrly, SOC or family details)
  *
  * Most of the conditional compilation will (someday) vanish.
  */

@@ -974,9 +974,9 @@ static void musb_shutdown(struct platfor
 /*
  * The silicon either has hard-wired endpoint configurations, or else
  * "dynamic fifo" sizing.  The driver has support for both, though at this
- * writing only the dynamic sizing is very well tested.   We use normal
- * idioms to so both modes are compile-tested, but dead code elimination
- * leaves only the relevant one in the object file.
+ * writing only the dynamic sizing is very well tested.   Since we switched
+ * away from compile-time hardware parameters, we can no longer rely on
+ * dead code elimination to leave only the relevant one in the object file.
  *
  * We don't currently use dynamic fifo setup capability to do anything
  * more than selecting one of a bunch of predefined configurations.

@@ -108,7 +108,7 @@ static void musb_ep_program(struct musb 
 /*
  * Clear TX fifo. Needed to avoid BABBLE errors.
  */
-static inline void musb_h_tx_flush_fifo(struct musb_hw_ep *ep)
+static void musb_h_tx_flush_fifo(struct musb_hw_ep *ep)
 {
 	void __iomem	*epio = ep->regs;
 	u16		csr;

@@ -436,7 +436,7 @@ musb_advance_schedule(struct musb *musb,
 	}
 }
 
-static inline u16 musb_h_flush_rxfifo(struct musb_hw_ep *hw_ep, u16 csr)
+static u16 musb_h_flush_rxfifo(struct musb_hw_ep *hw_ep, u16 csr)
 {
 	/* we don't want fifo to fill itself again;
 	 * ignore dma (various models),

@@ -1005,7 +1005,7 @@ static bool musb_h_ep0_continue(struct m
 
 /*
  * Handle default endpoint interrupt as host. Only called in IRQ time
- * from the LinuxIsr() interrupt service routine.
+ * from musb_interrupt().
  *
  * called with controller irqlocked
  */

@@ -836,7 +836,7 @@ struct drm_ioctl_desc i915_ioctls[] = {
 	DRM_IOCTL_DEF(DRM_I915_SET_VBLANK_PIPE,  i915_vblank_pipe_set, DRM_AUTH|DRM_MASTER|DRM_ROOT_ONLY ),
 	DRM_IOCTL_DEF(DRM_I915_GET_VBLANK_PIPE,  i915_vblank_pipe_get, DRM_AUTH ),
 	DRM_IOCTL_DEF(DRM_I915_VBLANK_SWAP, i915_vblank_swap, DRM_AUTH),
-	DRM_IOCTL_DEF(DRM_I915_HWS_ADDR, i915_set_status_page, DRM_AUTH),
+	DRM_IOCTL_DEF(DRM_I915_HWS_ADDR, i915_set_status_page, DRM_AUTH|DRM_MASTER|DRM_ROOT_ONLY),
 };
 
 int i915_max_ioctl = DRM_ARRAY_SIZE(i915_ioctls);

@@ -90,6 +90,7 @@ static void hauppauge_eeprom(struct au08
 	case 72221: /* WinTV-HVR950q (OEM, IR, ATSC/QAM and basic analog video */
 	case 72231: /* WinTV-HVR950q (OEM, IR, ATSC/QAM and basic analog video */
 	case 72241: /* WinTV-HVR950q (OEM, No IR, ATSC/QAM and basic analog video */
+	case 72251: /* WinTV-HVR950q (Retail, IR, ATSC/QAM and basic analog video */
 	case 72301: /* WinTV-HVR850 (Retail, IR, ATSC and basic analog video */
 	case 72500: /* WinTV-HVR950q (OEM, No IR, ATSC/QAM */
 		break;

@@ -198,6 +199,8 @@ struct usb_device_id au0828_usb_id_table
 		.driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 	{ USB_DEVICE(0x2040, 0x721b),
 		.driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
+	{ USB_DEVICE(0x2040, 0x721e),
+		.driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 	{ USB_DEVICE(0x2040, 0x721f),
 		.driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 	{ USB_DEVICE(0x2040, 0x7280),

@@ -42,6 +42,10 @@ struct usb_device_id smsusb_id_table[] =
 		.driver_info = SMS1XXX_BOARD_HAUPPAUGE_WINDHAM },
 	{ USB_DEVICE(0x2040, 0x5510),
 		.driver_info = SMS1XXX_BOARD_HAUPPAUGE_WINDHAM },
+	{ USB_DEVICE(0x2040, 0x5520),
+		.driver_info = SMS1XXX_BOARD_HAUPPAUGE_WINDHAM },
+	{ USB_DEVICE(0x2040, 0x5530),
+		.driver_info = SMS1XXX_BOARD_HAUPPAUGE_WINDHAM },
 	{ USB_DEVICE(0x2040, 0x5580),
 		.driver_info = SMS1XXX_BOARD_HAUPPAUGE_WINDHAM },
 	{ USB_DEVICE(0x2040, 0x5590),