twl4030 irq updates

PATCH In review David Brownell 1 participant 2 messages Oct 18, 2008 – Oct 20, 2008

Subsystems (2)

Multifunction devices (MFD) OMAP2+ support

lore

Share & tools

lore

David Brownell

author

2008-10-18 02:16 UTC #0 lore raw

PATCH 1/3 twl4030 irq updates

From: David Brownell <[email protected]>

This updates the IRQ handling support for the twl4030 driver:

- Move it into a separate file; clean and streamline it
- Restructure the init code for reuse during secondary dispatch
- Support both levels (primary, secondary) of IRQ dispatch
- Use a workqueue for irq mask/unmask and trigger configuration

Code for two subchips currently share that secondary handler code. One is the power subchip; its IRQs are now handled by this core, courtesy of this patch. The other is the GPIO module, which will be supported through a later patch.

There are also minor changes to the header file, mostly related to GPIO support; nothing yet in mainline cares about those. A few references to OMAP-specific symbols are disabled; when they can all be removed, the TWL4030 support ceases being OMAP-specific.

Signed-off-by David Brownell <[email protected]>

Signed-off-by Tony Lindgren <[email protected]>

---
This should go on top of the current MFD queue; it brings the relevant files in sync with what's in the linux-omap tree.

 drivers/mfd/Makefile        |    2 
 drivers/mfd/twl4030-core.c  |  485 ---------------------------
 drivers/mfd/twl4030-irq.c   |  743 ++++++++++++++++++++++++++++++++++++++++++
 include/linux/i2c/twl4030.h |   28 -
 4 files changed, 777 insertions(+), 481 deletions(-)

drivers/mfd/Makefile +1 -1

@@ -17,7 +17,7 @@ wm8350-objs			:= wm8350-core.o wm8350-re
 obj-$(CONFIG_MFD_WM8350)	+= wm8350.o
 obj-$(CONFIG_MFD_WM8350_I2C)	+= wm8350-i2c.o
 
-obj-$(CONFIG_TWL4030_CORE)	+= twl4030-core.o
+obj-$(CONFIG_TWL4030_CORE)	+= twl4030-core.o twl4030-irq.o
 
 obj-$(CONFIG_MFD_CORE)		+= mfd-core.o

drivers/mfd/twl4030-core.c +17 ~~-468~~

561 lines not on this page · raw message

drivers/mfd/twl4030-irq.c new file +743 -0

743 lines not on this page · raw message

include/linux/i2c/twl4030.h +16 ~~-12~~

@@ -228,6 +228,12 @@ struct twl4030_gpio_platform_data {
 	int		gpio_base;
 	unsigned	irq_base, irq_end;
 
+	/* package the two LED signals as output-only GPIOs? */
+	bool		use_leds;
+
+	/* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */
+	u8		mmc_cd;
+
 	/* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
 	 * should be enabled.  Else, if that bit is set in "pulldowns",
 	 * that pulldown is enabled.  Don't waste power by letting any

@@ -277,6 +283,8 @@ struct twl4030_platform_data {
 
 /*----------------------------------------------------------------------*/
 
+int twl4030_sih_setup(int module);
+
 /*
  * FIXME completely stop using TWL4030_IRQ_BASE ... instead, pass the
  * IRQ data to subsidiary devices using platform device resources.

@@ -291,16 +299,16 @@ struct twl4030_platform_data {
 #define TWL4030_MODIRQ_BCI		(TWL4030_IRQ_BASE + 2)
 #define TWL4030_MODIRQ_MADC		(TWL4030_IRQ_BASE + 3)
 /* #define TWL4030_MODIRQ_USB		(TWL4030_IRQ_BASE + 4) */
-#define TWL4030_MODIRQ_PWR		(TWL4030_IRQ_BASE + 5)
+/* #define TWL4030_MODIRQ_PWR		(TWL4030_IRQ_BASE + 5) */
 
 #define TWL4030_PWRIRQ_PWRBTN		(TWL4030_PWR_IRQ_BASE + 0)
-#define TWL4030_PWRIRQ_CHG_PRES		(TWL4030_PWR_IRQ_BASE + 1)
-#define TWL4030_PWRIRQ_USB_PRES		(TWL4030_PWR_IRQ_BASE + 2)
-#define TWL4030_PWRIRQ_RTC		(TWL4030_PWR_IRQ_BASE + 3)
-#define TWL4030_PWRIRQ_HOT_DIE		(TWL4030_PWR_IRQ_BASE + 4)
-#define TWL4030_PWRIRQ_PWROK_TIMEOUT	(TWL4030_PWR_IRQ_BASE + 5)
-#define TWL4030_PWRIRQ_MBCHG		(TWL4030_PWR_IRQ_BASE + 6)
-#define TWL4030_PWRIRQ_SC_DETECT	(TWL4030_PWR_IRQ_BASE + 7)
+/* #define TWL4030_PWRIRQ_CHG_PRES		(TWL4030_PWR_IRQ_BASE + 1) */
+/* #define TWL4030_PWRIRQ_USB_PRES		(TWL4030_PWR_IRQ_BASE + 2) */
+/* #define TWL4030_PWRIRQ_RTC		(TWL4030_PWR_IRQ_BASE + 3) */
+/* #define TWL4030_PWRIRQ_HOT_DIE		(TWL4030_PWR_IRQ_BASE + 4) */
+/* #define TWL4030_PWRIRQ_PWROK_TIMEOUT	(TWL4030_PWR_IRQ_BASE + 5) */
+/* #define TWL4030_PWRIRQ_MBCHG		(TWL4030_PWR_IRQ_BASE + 6) */
+/* #define TWL4030_PWRIRQ_SC_DETECT	(TWL4030_PWR_IRQ_BASE + 7) */
 
 /* Rest are unsued currently*/

@@ -317,17 +325,13 @@ struct twl4030_platform_data {
 /* TWL4030 GPIO interrupt definitions */
 
 #define TWL4030_GPIO_IRQ_NO(n)		(TWL4030_GPIO_IRQ_BASE + (n))
-#define TWL4030_GPIO_IS_ENABLE		1
 
 /*
  * Exported TWL4030 GPIO APIs
  *
  * WARNING -- use standard GPIO and IRQ calls instead; these will vanish.
  */
-int twl4030_get_gpio_datain(int gpio);
-int twl4030_request_gpio(int gpio);
 int twl4030_set_gpio_debounce(int gpio, int enable);
-int twl4030_free_gpio(int gpio);
 
 #if defined(CONFIG_TWL4030_BCI_BATTERY) || \
 	defined(CONFIG_TWL4030_BCI_BATTERY_MODULE)