Skip to contentSkip to conversation

new board SDRAM conf

U-Boot 조기성 2 participants 8 messages Nov 3, 2008 – Nov 4, 2008

lore
Share & tools
lore

조기성

author
#0 lore raw

Hi!,

I?m using ppc440Ep and using u-boot1.3.3

I?m using u-boot1.1.3 with Yosemite configuration.

When I boot with Yosemite conf , it stops SDRAM:256 , it? shows cpu, pci conf

My New Board configuration is only different SDRAM Size and Flash Size.

Where can I modify my Yosemite configuration.

Init.S and Yosemite.h

Best Regards,

J

###### Yosemite Cofiguration #####################

FLASH (CS0)

64MEGA Boot Flash

SDRAM

bank 0- 128MB

bank 1- 128MB

!!!###### My Board #####################

FLASH (CS0)

8MEGA Boot Flash

SDRAM

bank 0- 128MB

bank 1- NONE

#1 lore raw
Quoted 3 lines · ???

I?m using ppc440Ep and using u-boot1.3.3

I?m using u-boot1.1.3 with Yosemite configuration.

Please use the latest version from the DENX git repository.

Quoted 2 lines

When I boot with Yosemite conf , it stops SDRAM:256 , it? shows cpu, pci conf

So it most likely crashed upon relocation into SDRAM. So its an SDRAM configuration problem.

Quoted 6 lines

My New Board configuration is only different SDRAM Size and Flash Size.

Where can I modify my Yosemite configuration.

Init.S and Yosemite.h

Yosemite uses a board specific SDRAM init routine. I suggest that you use the common DDR2 init code by enabling it in your board config header (include/configs/board.h):

#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0*/

You can also define CONFIG_SYS_SDRAM_TABLE if you have an uncommon SDRAM configuration. What's the difference of your SDRAM configuration?

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

author
#2 lore raw

Dear stefan.

I Made my board config header, and using yosemite's init.S & u-boot.lds, mft.c(Yosemite.c) Only change config header , but it's not working .

1. First The difference of my SDRAM configuration is
*** (PPC440EP supported four external DDR_SDRAM Banks.) ***
But Our used only external DDR_SDRAM Bank_0(BANKSEL_0) on the New design Board.

2. Second my config header is
Include/configs/mft.h
________________________________________________________________________________________
#define CONFIG_440EP 1 /* Specific PPC440EP support */
#define CONFIG_HOSTNAME mft

#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */

#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
#define CONFIG_BOARD_RESET 1 /* call board_reset() */

/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/
#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
#if 1 //steven
#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
#else
#define CFG_MONITOR_BASE TEXT_BASE

#define CFG_SDRAM_BASE	        0x00000000	    /* _must_ be 0	*/
#define CFG_FLASH_BASE	        0xfc000000	    /* start of FLASH	*

...
/*-----------------------------------------------------------------------
* DDR SDRAM *----------------------------------------------------------------------*/
#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
#if 0 //steven
#define CFG_KBYTES_SDRAM (128 * 1024) /* 128MB */
#else
#define CFG_KBYTES_SDRAM (64 * 1024) /* 128MB */
#endif
#if 1 //steven
#define CFG_SDRAM_BANKS (2)
#else
#define CFG_SDRAM_BANKS (1)
#endif

define CONFIG_SDRAM_BANK0 1
_________________________________________________________________________________________

The difference of your SDRAM configuration?

Quoted 1 line
Quoted 1 line
Quoted 1 line

Best Regards.
Steven

-----Original Message-----
From: Stefan Roese [mailto:sr at denx.de]
Sent: Monday, November 03, 2008 4:47 PM
To: u-boot at lists.denx.de; k9 at tibetsystem.com
Subject: Re: [U-Boot] new board SDRAM conf

Quoted 3 lines · ???

I?m using ppc440Ep and using u-boot1.3.3

I?m using u-boot1.1.3 with Yosemite configuration.

Please use the latest version from the DENX git repository.

Quoted 2 lines

When I boot with Yosemite conf , it stops SDRAM:256 , it? shows cpu, pci conf

So it most likely crashed upon relocation into SDRAM. So its an SDRAM configuration problem.

Quoted 6 lines

My New Board configuration is only different SDRAM Size and Flash Size.

Where can I modify my Yosemite configuration.

Init.S and Yosemite.h

Yosemite uses a board specific SDRAM init routine. I suggest that you use the common DDR2 init code by enabling it in your board config header (include/configs/board.h):

#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0*/

You can also define CONFIG_SYS_SDRAM_TABLE if you have an uncommon SDRAM configuration. What's the difference of your SDRAM configuration?

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#3 lore raw

Hi Steven,

Quoted 2 lines · ???

I Made my board config header, and using yosemite's init.S & u-boot.lds, mft.c(Yosemite.c) Only change config header , but it's not working .

You should create your own board port for this custom 440EP board.

Quoted 4 lines

1. First The difference of my SDRAM configuration is
*** (PPC440EP supported four external DDR_SDRAM Banks.) *** But Our used only external DDR_SDRAM Bank_0(BANKSEL_0) on the New design Board.

Yes. I already described how you should handle this DDR initialization in my last mail. Use the common code (cpu/ppc4xx/sdram.c). You probably need to change the CONFIG_SYS_SDRAM_TABLE for your board. Take a look at the p3p440.h header as an example.

BTW: SDRAM configuration is a complex matter. You definitely need to take a look at the PPC users manual and the SDRAM datasheet for this.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

author
#4 lore raw

Hi, thanks in your replay.

I create My own board port(MFT board) . create configuration header and init.S But In the sdram.c(sdram_init->get_ram_size is 4 thus )func is failed , sdram is not founded . I think init.S is something wrong or CFG_MONITOR_BASE is wrong ... .

maybe you can point me to the right direction.

It's my board init.S

_____________________________________________________________________________________________________
tlbtab:

    tlbtab_start

    /*
     * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
     * speed up boot process. It is patched after relocation to enable SA_I
     */
    tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/)

    /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
    tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G )

    tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
    tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I )
    tlbentry( CFG_NVRAM_BASE_ADDR, SZ_256M, CFG_NVRAM_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_W|SA_I )

    /* PCI */
    tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I )
    tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 0, AC_R|AC_W|SA_G|SA_I )
    tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 0, AC_R|AC_W|SA_G|SA_I )
    tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 0, AC_R|AC_W|SA_G|SA_I )

    /* USB 2.0 Device */
    tlbentry( CFG_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_R|AC_W|SA_G|SA_I )

    tlbtab_en

_____________________________________________________________________________________________________

My SDRAM is 128MB mode 3, 13x10(4)
And use external DDR_SDRAM Bank_0(BANKSEL_0)

It's my board configuration header.

_____________________________________________________________________________________________________
Include/configs/mft.h
#define CONFIG_440EP 1 /* Specifc GP support */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll *
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
#define CFG_MONITOR_BASE CFG_FLASH_BASE /* start of monitor */

/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/
#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */
#define CFG_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */
#define CFG_ISRAM_BASE CFG_INIT_RAM_ADDR /* internal SRAM */
#define CFG_INIT_RAM_END (4 << 10) /* End of used area in RAM */
//#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */

#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET

#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/

/*-----------------------------------------------------------------------
* DDR SDRAM *----------------------------------------------------------------------*/
#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0*/
#define CFG_SDRAM0_TR0 0x410A4012
#undef CONFIG_SDRAM_ECC /* enable ECC support */

#if 1

#define CFG_SDRAM_TABLE	{ \
		{(128 << 20), 13, 0x000A4001}, /* 128MB mode 3, 13x10(4)*/ \
		{(128 << 20), 12, 0x000A2001}, /* 128MB mode 2, 13x10(4)*/ \
		{(64 << 20),  13, 0x00084001}, /* 64MB mode 3, 13x9(4)	*/ \
		{(64 << 20),  12, 0x00082001}, } /* 64MB mode 2, 13x9(4)	*

/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/
#define CFG_FLASH0 0xFF800000
#define CFG_FLASH1 0xFF000000
#define CFG_FLASH2 0xFE800000
#define CFG_FLASH3 0xFE000000
#define CFG_USB 0xF0000000

/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
//#define CFG_EBC_PB0AP 0x03050200
#define CFG_EBC_PB0AP 0x03017300
#define CFG_EBC_PB0CR (CFG_FLASH0 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit *

_____________________________________________________________________________________________________

Best Regards.
Steven.

-----Original Message-----
From: Stefan Roese [mailto:sr at denx.de]
Sent: Monday, November 03, 2008 7:11 PM
To: u-boot at lists.denx.de; [email protected]
Subject: Re: [U-Boot] new board SDRAM conf

Hi Steven,

Quoted 2 lines · ???

I Made my board config header, and using yosemite's init.S & u-boot.lds, mft.c(Yosemite.c) Only change config header , but it's not working .

You should create your own board port for this custom 440EP board.

Quoted 4 lines

1. First The difference of my SDRAM configuration is
*** (PPC440EP supported four external DDR_SDRAM Banks.) *** But Our used only external DDR_SDRAM Bank_0(BANKSEL_0) on the New design Board.

Yes. I already described how you should handle this DDR initialization in my last mail. Use the common code (cpu/ppc4xx/sdram.c). You probably need to change the CONFIG_SYS_SDRAM_TABLE for your board. Take a look at the p3p440.h header as an example.

BTW: SDRAM configuration is a complex matter. You definitely need to take a look at the PPC users manual and the SDRAM datasheet for this.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#5 lore raw
Quoted 8 lines · ???

I create My own board port(MFT board) . create configuration header and init.S But In the sdram.c(sdram_init->get_ram_size is 4 thus )func is failed , sdram is not founded . I think init.S is something wrong or CFG_MONITOR_BASE is wrong ... .

maybe you can point me to the right direction.

It's my board init.S

Your init.S is not optimal but at least not the reason for the problem. You are programming a 256MB TLB entry for SDRAM. This is more than enough for your 128MB. You should fix this at some time but it not the problem right now. CFG_MONITOR_BASE is also most likely not the problem.

<snip>

Quoted 2 lines

My SDRAM is 128MB mode 3, 13x10(4)
And use external DDR_SDRAM Bank_0(BANKSEL_0)

OK.

<snip>

Quoted 8 lines

/*-----------------------------------------------------------------------
* DDR SDRAM *----------------------------------------------------------------------*/
#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0*/
#define CFG_SDRAM0_TR0 0x410A4012
#undef CONFIG_SDRAM_ECC /* enable ECC support */

Quoted 6 lines

#if 1

#define CFG_SDRAM_TABLE	{ \
		{(128 << 20), 13, 0x000A4001}, /* 128MB mode 3, 13x10(4)*/ \
		{(128 << 20), 12, 0x000A2001}, /* 128MB mode 2, 13x10(4)*/ \
		{(64 << 20),  13, 0x00084001}, /* 64MB mode 3, 13x9(4)	*/ \
		{(64 << 20),  12, 0x00082001}, } /* 64MB mode 2, 13x9(4)	*

Why do you define so many entries in this table? One (128MB mode 3) should be enough for you. If get_ram_size() doesn't return 128MB in this init function then you need to check whether you have a problems with the timings. Use a debugger (or test routines) to see if some bits fail etc.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================

author
#6 lore raw

Hi Stefan.
I solved SDRAM problems for your help, when I use CFG_DRAM_TEST , it passed

My bdi2000's configuration is blows
WDCR 0x10 0x00000020 ;Select SDRAM0_CFG0
WDCR 0x11 0x34000000 ;CFG0: 32bit, PMU disable
WDCR 0x11 0x84000000 ;CFG1: enable SDRA

When I Use BID2000, accessing SDRAM with Verify, mm command, It works fine .
I think SDRAM0_CFG first is CFG0, and second is CFG1.

But in board/amcc/mft.c I used marked code, It's confused me. Long int sdram_init()

{
	
	//mtsdram (mem_cfg0, 0x34000000); /* confused me */
	//mtsdram (mem_cfg1, 0x84000000);
	mtsdram (mem_cfg1, 0x34000000);/* it works fine */
	mtsdram (mem_cfg0, 0x84000000);
}

I have another problem.
cpu/ppc4XX/start.S -> trab_init function has exception error blows LOG MESSAGE.
When I debug trap_init , use blr code it succefully returned.
maybe you can point me to the right direction.

trap_init:

	lwz	r7, GOT(_start_of_vectors)
	lwz	r8, GOT(_end_of_vectors)

	li	r9, 0x100		/* reset vector always at 0x100 */

	cmplw	0, r7, r8
	bgelr				/* return if r7>=r8 - just in case */

	mflr	r4			/* save link register		*/
1:
	lwz	r0, 0(r7)
	stw	r0, 0(r9)
	addi	r7, r7, 4
	addi	r9, r9, 4
	cmplw	0, r7, r8
	bne	1b

/* blr (in this use blr it works Steven) */

Best Regards.
Steven.

______________________________LOG MESSAGE_____________________________________________________ U-Boot 1.3.3 (Nov 4 2008 - 18:19:01)

CPU: AMCC PowerPC 440EP Rev. C at 333.333 MHz (PLB=133, OPB=66, EBC=33 MHz)
Bootstrap Option E - Boot ROM Location EBC (16 bits) Internal PCI arbiter enabled, PCI async ext clock used 32 kB I-Cache 32 kB D-Cache

Board: MFT(Multi Function Tester) - AMCC PPC440EP Evaluation Board
I2C:   ready
DTT:   1 FAILED INIT
DRAM:  128 MB

[init_func_ram]K9 board_add_ram leave
[board_init_f]enter
[board_init_f:465]
[board_init_f:468]
Top of RAM usable for U-Boot at: 08000000
Reserving 593k for U-Boot at: 07f6b000
Reserving 136k for malloc() at: 07f49000
Reserving 144 Bytes for Board Info at: 07f48f70
Reserving 56 Bytes for Global Data at: 07f48f38
Stack Pointer at: 07f48f18
[board.c:639]
New Stack Pointer is: 07f48f18
[board_init_f:657]addr_sp:0x7f48f18, id:0x7f48f38, addr:0x7f6b000 [board_init_r:679]enter
Now running in RAM - U-Boot at: 07f6b000
[board_init_r:706]before watchdog_reset
[board_init_r:709]after watchdog
[board_init_r:772]
[board_init_r:790]
Bus Fault @ 0x07f6d7c0, fixup 0x00000000
Machine Check Exception.
Caused by (from msr): regs 07f48df8 Data Read PLB Error
Data Write PLB Error
Machine Check exception is imprecise
NIP: 07F6D7C0 XER: 00000000 LR: 07F6D7C0 REGS: 07f48df8 TRAP: 0200 DEAR: CE3EFACB
MSR: 00021000 EE: 0 PR: 0 FP: 0 ME: 1 IR/DR: 00

GPR00: 07F6D358 07F48EE8 07F48F38 07F6B000 07F6E6F8 00000001 00000001 07F6D7C0
GPR08: 00000600 00002098 01FCA055 00000000 07F48CF8 27000800 07FB2100 07FEB000
GPR16: 10010000 06110000 00A94200 00638800 24009000 CB010000 00000000 FFFB3B8C
GPR24: FFFB2A30 07F48F38 07F6B000 07F6B000 07F9EB8C 07F9DA20 07FB21B4 07F48F70 Call backtrace:
07F6E6F0 07F6D734
machine check

__________________________________________________________________________________________

Include/configs/mft.h /*-----------------------------------------------------------------------
* High Level Configuration Options *----------------------------------------------------------------------*/
#define CONFIG_440EP 1 /* Specifc EP support */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */

/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 *
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
#define CFG_MONITOR_BASE TEXT_BASE
//#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory */

#define CFG_PCI_MEMBASE1        CFG_PCI_MEMBASE  + 0x10000000
#define CFG_PCI_MEMBASE2        CFG_PCI_MEMBASE1 + 0x10000000
#define CFG_PCI_MEMBASE3        CFG_PCI_MEMBASE2 + 0x10000000

#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs */

#define CFG_USB_DEVICE 0x50000000
#define CFG_NVRAM_BASE_ADDR 0x80000000
#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000)
#define CFG_BOOT_BASE_ADDR 0xf0000000
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/
#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */
#define CFG_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */
#define CFG_ISRAM_BASE CFG_INIT_RAM_ADDR /* internal SRAM */
#define CFG_INIT_RAM_END (4 << 10) /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */

#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET

#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/

/*-----------------------------------------------------------------------
* DDR SDRAM *----------------------------------------------------------------------*/
#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
//#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0*/
//#define CFG_SDRAM0_TR0 0x410A4012
#undef CONFIG_SDRAM_ECC /* enable ECC support */

#if 1 // for sdram test
#define CFG_DRAM_TEST
#define CFG_KBYTES_SDRAM (128 * 1024)
#endif

#7 lore raw

Hi Steven,

Quoted 14 lines · ???

I solved SDRAM problems for your help, when I use CFG_DRAM_TEST , it passed

My bdi2000's configuration is blows
WDCR 0x10 0x00000020 ;Select SDRAM0_CFG0
WDCR 0x11 0x34000000 ;CFG0: 32bit, PMU disable
WDCR 0x11 0x84000000 ;CFG1: enable SDRA

When I Use BID2000, accessing SDRAM with Verify, mm command, It works fine . I think SDRAM0_CFG first is CFG0, and second is CFG1.

But in board/amcc/mft.c I used marked code, It's confused me. Long int sdram_init()
{

Quoted 5 lines
	//mtsdram (mem_cfg0, 0x34000000); /* confused me */
	//mtsdram (mem_cfg1, 0x84000000);
	mtsdram (mem_cfg1, 0x34000000);/* it works fine */
	mtsdram (mem_cfg0, 0x84000000);
}

Not sure if I understand what you are trying to tell me? Did you find a problem in the common code? Or is it a problem with your BDI config script?

Quoted 23 lines

I have another problem.
cpu/ppc4XX/start.S -> trab_init function has exception error blows LOG
MESSAGE. When I debug trap_init , use blr code it succefully returned. maybe you can point me to the right direction.

trap_init:

	lwz	r7, GOT(_start_of_vectors)
	lwz	r8, GOT(_end_of_vectors)

	li	r9, 0x100		/* reset vector always at 0x100 */

	cmplw	0, r7, r8
	bgelr				/* return if r7>=r8 - just in case */

	mflr	r4			/* save link register		*/
1:
	lwz	r0, 0(r7)
	stw	r0, 0(r9)
	addi	r7, r7, 4
	addi	r9, r9, 4
	cmplw	0, r7, r8
	bne	1b
Quoted 1 line

/* blr (in this use blr it works Steven) */

So when you add this "blr" here you can boot successfully to the U-Boot prompt? And without it you get the exceptions printed below? That's strange. It works on all other known 4xx platforms without problem as far as I know.

Make sure to start "fresh" from the BDI by using "reset run".

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================