at91: add support for PM9263 board
Subsystems (2)
PATCH 1/1 at91: add support for PM9263 board
This patch adds support for the PM9263 board of Ronetix GmbH (www.ronetix.at)
--- MAKEALL | 1 + Makefile | 3 + board/ronetix/pm9263/Makefile | 60 ++++ board/ronetix/pm9263/config.mk | 1 + board/ronetix/pm9263/pm9263.c | 504 +++++++++++++++++++++++++++ board/ronetix/pm9263/pm9263_led.c | 66 ++++ board/ronetix/pm9263/pm9263_lowlevel_init.S | 376 ++++++++++++++++++++ board/ronetix/pm9263/pm9263_nand.c | 79 +++++ board/ronetix/pm9263/pm9263_partition.c | 47 +++ include/configs/pm9263.h | 279 +++++++++++++++ tools/Makefile | 3 + tools/logos/ronetix.bmp | Bin 0 -> 5638 bytes 12 files changed, 1419 insertions(+), 0 deletions(-) create mode 100644 board/ronetix/pm9263/Makefile create mode 100644 board/ronetix/pm9263/config.mk create mode 100644 board/ronetix/pm9263/pm9263.c create mode 100644 board/ronetix/pm9263/pm9263_led.c create mode 100644 board/ronetix/pm9263/pm9263_lowlevel_init.S create mode 100644 board/ronetix/pm9263/pm9263_nand.c create mode 100644 board/ronetix/pm9263/pm9263_partition.c create mode 100644 include/configs/pm9263.h create mode 100644 tools/logos/ronetix.bmp
MAKEALL +1 -0
@@ -545,6 +545,7 @@ LIST_at91=" \ kb9202 \ mp2usb \ m501sk \ + pm9263 \ " #########################################################################
Makefile +3 -0
@@ -2561,6 +2561,9 @@ at91cap9adk_config : unconfig at91sam9260ek_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs at91sam9260ek atmel at91 +pm9263_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm926ejs pm9263 ronetix at91 + ######################################################################## ## ARM Integrator boards - see doc/README-integrator for more info. integratorap_config \
board/ronetix/pm9263/Makefile new file +60 -0
60 lines not on this page · raw message
board/ronetix/pm9263/config.mk new file +1 -0
@@ -0,0 +1 @@ +TEXT_BASE = 0x23f00000
board/ronetix/pm9263/pm9263.c new file +504 -0
504 lines not on this page · raw message
board/ronetix/pm9263/pm9263_led.c new file +66 -0
66 lines not on this page · raw message
board/ronetix/pm9263/pm9263_lowlevel_init.S new file +376 -0
376 lines not on this page · raw message
board/ronetix/pm9263/pm9263_nand.c new file +79 -0
79 lines not on this page · raw message
board/ronetix/pm9263/pm9263_partition.c new file +47 -0
47 lines not on this page · raw message
include/configs/pm9263.h new file +279 -0
279 lines not on this page · raw message
tools/Makefile +3 -0
@@ -47,6 +47,9 @@ endif ifeq ($(VENDOR),atmel) LOGO_BMP= logos/atmel.bmp endif +ifeq ($(VENDOR),ronetix) +LOGO_BMP= logos/ronetix.bmp +endif #-------------------------------------------------------------------------
tools/logos/ronetix.bmp new file binary +0 -0
zc%03cKU~{J6vq!FPL^XEQ4<1A027nM#06YR5|^g at OKA-xvFpaEo7M?2RUxKo5Z8f` zk&)3OBO@bYMn*=D9z8NL_UZmevTPuqe43=c5AXA&)4g|Jo$j7w=AYmmM1|WCii6(= zi-NTwAG^>E=VQ$NLCl!oy3YrH8uDqD^&-u(Udy7W*Rp67MXAM6G#*FscoM~vNt8^c zP%@Q5DQdGQH9L!Dsio0uI*roQvXJKlrL$R-rB;A^Cty{SEfgSU6&1i23M-Hsj#pOD z3RpZ at 1;36~*4JT-Dq07hqJ9&0l&G4Ho<1oRq)#|4)|^G*(%xwzrDSKws&@5j2hYj zU!Z;$?d<NNU21!ftA=*>_Rt>KeqIC)Zn;+_9_*Kub~R~N at X8a_V>{~wF8K&qy2*e zbU^J89ULB_L$FGv4*m!o9a;7cuGPeJMf2f^bY)?<&TfiG1$@3Dfkm;2Y+&cPN-F( z?G#n3RXDbM4OMGk)l*ahU#r)_pP{<t>y&QJw>O~&d}M}8G1<m-%=+&H^IdU$jQ%* zaG>V<efpIqzjeIa%O(6QS(bh==6GeZf-j3idvp#m#6c at n4f8gn3*fnE{j$(4Jy+f zGYdNJIbCuCJj-wl}J!k<?#l*)vy|1x`LBSAuM@?)lrkA+a#&&h7&a-uA)(*E1rn9 zJ_EX#p?2%|Ivf^d+OFtRh;;}XPO2p4YVTjO_!<HAFJy&FioXhCwONX^OqSsSj at eOp zMd26a38DuSPlPmL@rA8q_@>3 at w|XdnHF8s8Q8t1ZmlZxr!X%VWm0>~zUbifg$_cU{ zwZMZbF%MrUWZ#Fwr-*sL3YPA-<kQJU4~xWUmZ==&<12WYu0M8vQ+%NHu#G2;5;Dp7 z6h|!C)kZ$EmqsaCz{Tg++zMq|^T8nn!~wbl*LwJjV0Do=eDZBRdp$NDhC3zY}^Mq zpSD>F%CEKjk0cq|f2QVZ(H3bMqWNl2LqCbjLMVf<-YsIG7Dz7cw|A?Q^_w(vL~ z&N<7IJNAxB1<YwOiM1lZsO57eB?eGR7#OzC&!buB5CF;_lnu$41+QoH4F8^X2Ja zaLf9*{2_cMUvmD*PQHqzK3xR4_>AlJ?BN;m-h5?^WtGz;id#S5i}}bJ=j!0wUXD4{ z#^Ez=ICy+By$_#xgWWyscG8dC=gU9q^(}eM_%|{WlZUqw5y4W&+Hd?SP^*d!<XU( ztQ+q6I&P>hTv#n#!bcWdczkI!@{O7?vG#nLvmGwyTf{!L_+Ak&pFNgQa&;#BC!84 zA;10M;lqh>F?;@N^Urd*=d0%Bd>yw)QRP!b at 9Bg2@|>a2lHg>^eC*V!!}Pq517} z0qem)bsaS><C7CcnD346h?~zEUD5K-neqj*iBE0dTN3L}>MoJLzl{tI+z~U#H=p-~ z3Co~8aVcMFhL<j02sz)DRcGKG<B^L43JH9OlDIeP#0ItH{vMP-N^c7W9JlgnI0V zcUIKmCG}aJy2jp3;c^2X>@~RsAEA6Qy_Y3x*)l#eDe&YGgRFdM;Q<TP!GRT~)dg zwr*>pds at 8TZaxsYA9B6l)L4M6FH!6TA6e6|qCL$tYMCxF+>^;X*6B-w@)@64}wWT zUJf$6p~1+HJn1}U#mkn?0i}6SJY3&^?7WZiPt&d%f!n^itt#lS7M7|874d~Q$D>< zym6HUi2L)-z>om^nP(l9#QT>kiUnWB{#<B~G|A?VojBj$4j;+jrX}r85F<u6Rsu#z z6L@~M$XA91;K0yJzHX!Pd3<K99V=d8DO4hh5<ipsoNC_(pSBYJJu at da1-b+u1Mtll zTo7+ux$;C@yo!V0KEH#HI=*C&fz1*!(JasLt*L)U##&Bf#IKy8{ep!$HHjHp-6 zmtV<{9F#GE7hbiKJc$Uv$k%UKQ^|kJ&DZbnS<~Aj+FE8>bNz52M!CGPA*RzTU8L7= zTWL$q-fcdWtMLd0DQ!op2l6*^-jgj_YpPD%7Yv?-K}r$MeIHDgtz5laiN%~FCU-J zs*_MxraaAW?%JF9j%Z7?iSjJI!c=+jWAj;clGT+)*_+tmGvnT$YKmHF3jEJiRQ<UY z&0-S|-nE;Io`zZnRpgWWXC|9(*~~Ywi;w7C?uvTl>JMhi$WNq4bdL;-xtjDBj(*oa QD;*(Q_XdWChX=;~1zg+&lK=n!
literal 0
Hc$@<O00001
Signature · 1 line
1.5.2.2
PATCH 1/1 at91: add support for PM9263 board
Quoted 2 lines · Ilko Iliev
This patch adds support for the PM9263 board of Ronetix GmbH (www.ronetix.at)
It will be nice it you could generate patch to see duplicate code to simplify the review.
This is >70% the same as the at91sam9263
As I announe I've send the common for RFC please take a look
Quoted 93 lines
Signed-off-by Ilko Iliev <[email protected]>--- MAKEALL | 1 + Makefile | 3 + board/ronetix/pm9263/Makefile | 60 ++++ board/ronetix/pm9263/config.mk | 1 + board/ronetix/pm9263/pm9263.c | 504 +++++++++++++++++++++++++++ board/ronetix/pm9263/pm9263_led.c | 66 ++++ board/ronetix/pm9263/pm9263_lowlevel_init.S | 376 ++++++++++++++++++++ board/ronetix/pm9263/pm9263_nand.c | 79 +++++ board/ronetix/pm9263/pm9263_partition.c | 47 +++ include/configs/pm9263.h | 279 +++++++++++++++ tools/Makefile | 3 + tools/logos/ronetix.bmp | Bin 0 -> 5638 bytes 12 files changed, 1419 insertions(+), 0 deletions(-) create mode 100644 board/ronetix/pm9263/Makefile create mode 100644 board/ronetix/pm9263/config.mk create mode 100644 board/ronetix/pm9263/pm9263.c create mode 100644 board/ronetix/pm9263/pm9263_led.c create mode 100644 board/ronetix/pm9263/pm9263_lowlevel_init.S create mode 100644 board/ronetix/pm9263/pm9263_nand.c create mode 100644 board/ronetix/pm9263/pm9263_partition.c create mode 100644 include/configs/pm9263.h create mode 100644 tools/logos/ronetix.bmpMAKEALL +1
-0@@ -545,6 +545,7 @@ LIST_at91=" \ kb9202 \ mp2usb \ m501sk \ + pm9263 \ " #########################################################################Makefile +3
-0@@ -2561,6 +2561,9 @@ at91cap9adk_config : unconfig at91sam9260ek_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs at91sam9260ek atmel at91 +pm9263_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm926ejs pm9263 ronetix at91 + ######################################################################## ## ARM Integrator boards - see doc/README-integrator for more info. integratorap_config \board/ronetix/pm9263/Makefile new file +36
-0@@ -0,0 +1,60 @@ +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# (C) Copyright 2008 +# Stelian Pop <[email protected]> +# Lead Tech Design <www.leadtechdesign.com> +# Ilko Iliev <www.ronetix.at> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += pm9263.o +COBJS-y += pm9263_led.o +COBJS-y += pm9263_partition.o +COBJS-$(CONFIG_CMD_NAND) += pm9263_nand.o
board/ronetix/pm9263/Makefile line 46
Quoted 10 lines
board/ronetix/pm9263/Makefile new file +10
-0+ +SOBJS := pm9263_lowlevel_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y) $(SOBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $@, $(OBJS)) +
^^^^^
please remove
Quoted 73 lines
board/ronetix/pm9263/Makefile new file +14
-0+clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################board/ronetix/pm9263/config.mk new file +1
-0@@ -0,0 +1 @@ +TEXT_BASE = 0x23f00000board/ronetix/pm9263/pm9263.c new file +46
-0@@ -0,0 +1,504 @@ +/* +* (C) Copyright 2007-2008 +* Stelian Pop <[email protected]> +* Lead Tech Design <www.leadtechdesign.com> +* Ilko Iliev <www.ronetix.at> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <common.h> +#include <asm/sizes.h> +#include <asm/arch/at91sam9263.h> +#include <asm/arch/at91sam9263_matrix.h> +#include <asm/arch/at91sam9_smc.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/io.h> +#include <asm/arch/hardware.h> +#include <lcd.h> +#include <atmel_lcdc.h> +#include <dataflash.h> +#if defined(CONFIG_RESET_PHY_R ) && defined(CONFIG_MACB ) +#include <net.h> +#endif +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR ; + +/* ------------------------------------------------------------------------- */
board/ronetix/pm9263/pm9263.c line 56
Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10
-0+/* +* Miscelaneous platform dependent initialisations +*/ + +static void pm9263_serial_hw_init (void ) +{ +#ifdef CONFIG_USART0 +at91_set_A_periph (AT91_PIN_PA26 ,1 );/* TXD0 */ +at91_set_A_periph (AT91_PIN_PA27 ,0 );/* RXD0 */ +at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_US0 );
please update to AT91SAM9263_ID_USx
board/ronetix/pm9263/pm9263.c line 62
Quoted 6 lines
board/ronetix/pm9263/pm9263.c new file +6
-0+#endif + +#ifdef CONFIG_USART1 +at91_set_A_periph (AT91_PIN_PD0 ,1 );/* TXD1 */ +at91_set_A_periph (AT91_PIN_PD1 ,0 );/* RXD1 */ +at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_US1 );
please update to AT91SAM9263_ID_USx
board/ronetix/pm9263/pm9263.c line 68
Quoted 6 lines
board/ronetix/pm9263/pm9263.c new file +6
-0+#endif + +#ifdef CONFIG_USART2 +at91_set_A_periph (AT91_PIN_PD2 ,1 );/* TXD2 */ +at91_set_A_periph (AT91_PIN_PD3 ,0 );/* RXD2 */ +at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_US2 );
please update to AT91SAM9263_ID_USx
board/ronetix/pm9263/pm9263.c line 74
Quoted 6 lines
board/ronetix/pm9263/pm9263.c new file +6
-0+#endif + +#ifdef CONFIG_USART3 /* DBGU */ +at91_set_A_periph (AT91_PIN_PC30 ,0 );/* DRXD */ +at91_set_A_periph (AT91_PIN_PC31 ,1 );/* DTXD */ +at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_SYS );
please update to AT91SAM9263_ID_USx
Quoted 16 lines
board/ronetix/pm9263/pm9263.c new file +16
-0+#endif +} + +#ifdef CONFIG_CMD_NAND +static void pm9263_nand_hw_init (void ) +{ +unsigned long csa; + +/* Enable CS3 */ + csa =at91_sys_read (AT91_MATRIX_EBI0CSA ); +at91_sys_write (AT91_MATRIX_EBI0CSA , + csa |AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA ); + +/* Configure SMC CS3 for NAND/SmartMedia */ + at91_sys_write(AT91_SMC_SETUP(3), + AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
board/ronetix/pm9263/pm9263.c line 100
Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10
-0+ AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); +at91_sys_write (AT91_SMC_PULSE (3 ), +AT91_SMC_NWEPULSE_ (3 ) |AT91_SMC_NCS_WRPULSE_ (3 ) | +AT91_SMC_NRDPULSE_ (3 ) |AT91_SMC_NCS_RDPULSE_ (3 )); +at91_sys_write (AT91_SMC_CYCLE (3 ), +AT91_SMC_NWECYCLE_ (5 ) |AT91_SMC_NRDCYCLE_ (5 )); +at91_sys_write (AT91_SMC_MODE (3 ), +AT91_SMC_READMODE |AT91_SMC_WRITEMODE | +AT91_SMC_EXNWMODE_DISABLE | +#ifdef CFG_NAND_DBW_16
please update to CONFIG_SYS
board/ronetix/pm9263/pm9263.c line 111
Quoted 11 lines
board/ronetix/pm9263/pm9263.c new file +11
-0+AT91_SMC_DBW_16 | +#else /* CFG_NAND_DBW_8 */ +AT91_SMC_DBW_8 | +#endif + AT91_SMC_TDF_(2)); + +/* Configure RDY/BSY */ +at91_set_gpio_input (AT91_PIN_PB30 ,1 ); + +/* Enable NandFlash */ +at91_set_gpio_output (AT91_PIN_PD15 ,1 );
why don't you initialize the clock here?
Quoted 17 lines
board/ronetix/pm9263/pm9263.c new file +17
-0+} +#endif + +#ifdef CONFIG_HAS_DATAFLASH +static void pm9263_spi_hw_init (void ) +{ +at91_set_B_periph (AT91_PIN_PA5 ,0 );/* SPI0_NPCS0 */ + +at91_set_B_periph (AT91_PIN_PA0 ,0 );/* SPI0_MISO */ +at91_set_B_periph (AT91_PIN_PA1 ,0 );/* SPI0_MOSI */ +at91_set_B_periph (AT91_PIN_PA2 ,0 );/* SPI0_SPCK */ + +/* Enable clock */ +at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_SPI0 ); +} +#endif +
board/ronetix/pm9263/pm9263.c line 138
Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10
-0+#ifdef CONFIG_MACB +static void pm9263_macb_hw_init (void ) +{ +/* Enable clock */ +at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_EMAC ); + +/* +* Disable pull-up on: +* RXDV (PC25) => PHY normal mode (not Test mode) +* ERX0 (PE25) => PHY ADDR0
^
whitespace please remove
Quoted 43 lines
board/ronetix/pm9263/pm9263.c new file +43
-0+* ERX1 (PE26) => PHY ADDR1 => PHYADDR = 0x0 +* +* PHY has internal pull-down +*/ +writel (pin_to_mask (AT91_PIN_PC25 ), +pin_to_controller (AT91_PIN_PC0 ) +PIO_PUDR ); +writel (pin_to_mask (AT91_PIN_PE25 ) | +pin_to_mask (AT91_PIN_PE26 ), +pin_to_controller (AT91_PIN_PE0 ) +PIO_PUDR ); + + +/* Re-enable pull-up */ +writel (pin_to_mask (AT91_PIN_PC25 ), +pin_to_controller (AT91_PIN_PC0 ) +PIO_PUER ); +writel (pin_to_mask (AT91_PIN_PE25 ) | +pin_to_mask (AT91_PIN_PE26 ), +pin_to_controller (AT91_PIN_PE0 ) +PIO_PUER ); + +at91_set_A_periph (AT91_PIN_PE21 ,0 );/* ETXCK_EREFCK */ +at91_set_B_periph (AT91_PIN_PC25 ,0 );/* ERXDV */ +at91_set_A_periph (AT91_PIN_PE25 ,0 );/* ERX0 */ +at91_set_A_periph (AT91_PIN_PE26 ,0 );/* ERX1 */ +at91_set_A_periph (AT91_PIN_PE27 ,0 );/* ERXER */ +at91_set_A_periph (AT91_PIN_PE28 ,0 );/* ETXEN */ +at91_set_A_periph (AT91_PIN_PE23 ,0 );/* ETX0 */ +at91_set_A_periph (AT91_PIN_PE24 ,0 );/* ETX1 */ +at91_set_A_periph (AT91_PIN_PE30 ,0 );/* EMDIO */ +at91_set_A_periph (AT91_PIN_PE29 ,0 );/* EMDC */ + +#ifndef CONFIG_RMII +at91_set_A_periph (AT91_PIN_PE22 ,0 );/* ECRS */ +at91_set_B_periph (AT91_PIN_PC26 ,0 );/* ECOL */ +at91_set_B_periph (AT91_PIN_PC22 ,0 );/* ERX2 */ +at91_set_B_periph (AT91_PIN_PC23 ,0 );/* ERX3 */ +at91_set_B_periph (AT91_PIN_PC27 ,0 );/* ERXCK */ +at91_set_B_periph (AT91_PIN_PC20 ,0 );/* ETX2 */ +at91_set_B_periph (AT91_PIN_PC21 ,0 );/* ETX3 */ +at91_set_B_periph (AT91_PIN_PC24 ,0 );/* ETXER */ +#endif + +} +#endif +
board/ronetix/pm9263/pm9263.c line 191
Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10
-0+#ifdef CONFIG_USB_OHCI_NEW +static void pm9263_uhp_hw_init (void ) +{ +/* Enable VBus on UHP ports */ +at91_set_gpio_output (AT91_PIN_PA21 ,0 ); +at91_set_gpio_output (AT91_PIN_PA24 ,0 ); +} +#endif + +#ifdef CONFIG_LCD
please move the lcd to a lcd.c file
Quoted 34 lines
board/ronetix/pm9263/pm9263.c new file +34
-0+vidinfo_t panel_info = { + vl_col:240 , + vl_row:320 , + vl_clk:4965000 , + vl_sync:ATMEL_LCDC_INVLINE_INVERTED | +ATMEL_LCDC_INVFRAME_INVERTED , + vl_bpix:3 , + vl_tft:1 , + vl_hsync_len:5 , + vl_left_margin:1 , + vl_right_margin:33 , + vl_vsync_len:1 , + vl_upper_margin:1 , + vl_lower_margin:0 , + mmio:AT91SAM9263_LCDC_BASE , +}; + +void lcd_enable (void ) +{ +at91_set_gpio_value (AT91_PIN_PA22 ,1 );/* power up */ +} + +void lcd_disable (void ) +{ +at91_set_gpio_value (AT91_PIN_PA22 ,0 );/* power down */ +} + +#ifdef LCD_IN_PSRAM + +#define PSRAM_CRE_PIN AT91_PIN_PB29 +#define PSRAM_CTRL_REG (PHYS_PSRAM + PHYS_PSRAM_SIZE - 2) + +/* Initialize the PSRAM memory */ +static int pm9263_lcd_hw_psram_init (void )
board/ronetix/pm9263/pm9263.c line 235
Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10
-0+{ +volatile uint16_t *p; +volatile uint16_t x; + +/* setup PB29 as output */ +at91_set_gpio_output (PSRAM_CRE_PIN ,1 ); + +at91_set_gpio_value (PSRAM_CRE_PIN ,0 );/* set PSRAM_CRE_PIN to '0' */ + + p = (volatile uint16_t *)PSRAM_CTRL_REG ;
please use readx/writex
and so on
Quoted 9 lines
board/ronetix/pm9263/pm9263.c new file +9
-0+ +/* PSRAM: write BCR */ + x = *p;/* mem r16 0x703ffffe 1 */ + x = *p;/* mem r16 0x703ffffe 1 */ + *p =1 ;/* mem w16 0x703ffffe 1 ; 0 for RCR, 1 for BCR */ + *p =0x9d4f ;/* write the BCR */ + +/* write RCR of the PSRAM */ + p = (volatile uint16_t *)PSRAM_CTRL_REG ;
board/ronetix/pm9263/pm9263.c line 254
Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10
-0+ x = *p;/* mem r16 0x703ffffe 1 */ + x = *p;/* mem r16 0x703ffffe 1 */ + *p =0 ;/* mem w16 0x703ffffe 0 ; 0 for RCR, 1 for BCR */ + + *p =0x90 ;/* set RCR; 0x10 - async mode, 0x90 - page mode */ + +/* test to see if the PSRAM is MT45W2M16A or MT45W2M16B +MT45W2M16B - CRE must be 0 +MT45W2M16A - CRE must be 1 +*/
please use this style of comment
board/ronetix/pm9263/pm9263.c line 258
Quoted 4 lines
board/ronetix/pm9263/pm9263.c new file +4
-0+ p = (volatile uint16_t *)PHYS_PSRAM ; + p[0 ] =0x1234 ; + p[1 ] =0x5678 ; +
^^^^^
whitespace please remove
board/ronetix/pm9263/pm9263.c line 264
Quoted 6 lines
board/ronetix/pm9263/pm9263.c new file +6
-0+/* test if the chip is MT45W2M16B */ +if ( (p[0 ] !=0x1234 ) || (p[1 ] !=0x5678 ) ) + { +/* try with CRE=1 (MT45W2M16A) */ +at91_set_gpio_value (PSRAM_CRE_PIN ,1 );/* set PSRAM_CRE_PIN to '1' */ +
^^^^^^^^^^^^^
whitespace please remove
board/ronetix/pm9263/pm9263.c line 248
Quoted 6 lines
board/ronetix/pm9263/pm9263.c new file +6
-0+/* write RCR of the PSRAM */ + p = (volatile uint16_t *)PSRAM_CTRL_REG ; + x = *p;/* mem r16 0x703ffffe 1 */ + x = *p;/* mem r16 0x703ffffe 1 */ + *p =0 ;/* mem w16 0x703ffffe 0 ; 0 for RCR, 1 for BCR */ +
^^^^^^^^^^^^^
whitespace please remove
board/ronetix/pm9263/pm9263.c line 277
Quoted 7 lines
board/ronetix/pm9263/pm9263.c new file +7
-0+ *p =0x90 ;/* set RCR; 0x10 - async mode, 0x90 - page mode */ + + p = (volatile uint16_t *)PHYS_PSRAM ; + p[0 ] =0x1234 ; + p[1 ] =0x5678 ; +if ( (p[0 ] !=0x1234 ) || (p[1 ] !=0x5678 ) ) +return 1 ;
^^^^^^^
whitespace please remove
and so on
Quoted 28 lines
board/ronetix/pm9263/pm9263.c new file +28
-0+ + } +return 0 ; +} +#endif + +static void pm9263_lcd_hw_init (void ) +{ +at91_set_A_periph (AT91_PIN_PC1 ,0 );/* LCDHSYNC */ +at91_set_A_periph (AT91_PIN_PC2 ,0 );/* LCDDOTCK */ +at91_set_A_periph (AT91_PIN_PC3 ,0 );/* LCDDEN */ +at91_set_B_periph (AT91_PIN_PB9 ,0 );/* LCDCC */ +at91_set_A_periph (AT91_PIN_PC6 ,0 );/* LCDD2 */ +at91_set_A_periph (AT91_PIN_PC7 ,0 );/* LCDD3 */ +at91_set_A_periph (AT91_PIN_PC8 ,0 );/* LCDD4 */ +at91_set_A_periph (AT91_PIN_PC9 ,0 );/* LCDD5 */ +at91_set_A_periph (AT91_PIN_PC10 ,0 );/* LCDD6 */ +at91_set_A_periph (AT91_PIN_PC11 ,0 );/* LCDD7 */ +at91_set_A_periph (AT91_PIN_PC14 ,0 );/* LCDD10 */ +at91_set_A_periph (AT91_PIN_PC15 ,0 );/* LCDD11 */ +at91_set_A_periph (AT91_PIN_PC16 ,0 );/* LCDD12 */ +at91_set_B_periph (AT91_PIN_PC12 ,0 );/* LCDD13 */ +at91_set_A_periph (AT91_PIN_PC18 ,0 );/* LCDD14 */ +at91_set_A_periph (AT91_PIN_PC19 ,0 );/* LCDD15 */ +at91_set_A_periph (AT91_PIN_PC22 ,0 );/* LCDD18 */ +at91_set_A_periph (AT91_PIN_PC23 ,0 );/* LCDD19 */ +at91_set_A_periph (AT91_PIN_PC24 ,0 );/* LCDD20 */ +at91_set_B_periph (AT91_PIN_PC17 ,0 );/* LCDD21 */
board/ronetix/pm9263/pm9263.c line 315
Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10
-0+at91_set_A_periph (AT91_PIN_PC26 ,0 );/* LCDD22 */ +at91_set_A_periph (AT91_PIN_PC27 ,0 );/* LCDD23 */ + +at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_LCDC ); + +/* Power Control */ +at91_set_gpio_output (AT91_PIN_PA22 ,1 ); +at91_set_gpio_value (AT91_PIN_PA22 ,0 );/* power down */ + +#ifdef LCD_IN_PSRAM
please use CONFIG_
Quoted 18 lines
board/ronetix/pm9263/pm9263.c new file +18
-0+/* initialize te PSRAM */ +int stat =pm9263_lcd_hw_psram_init (); + + gd->fb_base = (stat ==0 ) ?PHYS_PSRAM :AT91SAM9263_SRAM0_BASE ; +#else + gd->fb_base =AT91SAM9263_SRAM0_BASE ; +#endif + +} + +#ifdef CONFIG_LCD_INFO +#include <nand.h> +#include <version.h> + +extern flash_info_t flash_info[]; + +void lcd_show_board_info (void ) +{
board/ronetix/pm9263/pm9263.c line 343
Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10
-0+ulong dram_size, nand_size, flash_size, dataflash_size; +int i; +char temp[32 ]; + +lcd_printf ("%s\n" ,U_BOOT_VERSION ); +lcd_printf ("(C) 2008 Ronetix GmbH\n" ); +lcd_printf ("support at ronetix.at\n" ); +lcd_printf ("%s CPU at %s MHz" , +AT91_CPU_NAME , +strmhz (temp,AT91_MAIN_CLOCK ));
please use AT91_CPU_CLOCK
board/ronetix/pm9263/pm9263.c line 347
Quoted 4 lines
board/ronetix/pm9263/pm9263.c new file +4
-0+ + dram_size =0 ; +for (i =0 ; i <CONFIG_NR_DRAM_BANKS ; i++) + dram_size += gd->bd->bi_dram[i].size;
please fix all whitespace and remainig CFG_
Best Regards,
J.