Skip to contentSkip to conversation

e1000e: enable ECC correction on 82571 silicon

PATCH New Jeff Kirsher 1 participant 1 message Nov 14, 2008

Subsystems (2)
Networking Network drivers
lore
Share & tools
lore

Jeff Kirsher

author
#0 lore raw

PATCH 1/1 e1000e: enable ECC correction on 82571 silicon

From: Alexander Duyck <[email protected]>

This change enables ECC correction for the packet buffer on all 82571 silicon.

Signed-off-by Alexander Duyck <[email protected]>
Signed-off-by Jeff Kirsher <[email protected]>

---

 drivers/net/e1000e/82571.c   |    6 ++++++
 drivers/net/e1000e/defines.h |    7 +++++++
 drivers/net/e1000e/hw.h      |    1 +
 3 files changed, 14 insertions(+), 0 deletions(-)
drivers/net/e1000e/82571.c +6 -0
index b2c910c..3027ad5 100644
@@ -973,6 +973,12 @@ static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw)
 		ew32(CTRL_EXT, reg);
 	}
 
+	if (hw->mac.type == e1000_82571) {
+		reg = er32(PBA_ECC);
+		reg |= E1000_PBA_ECC_CORR_EN;
+		ew32(PBA_ECC, reg);
+	}
+
 	/* PCI-Ex Control Register */
 	if (hw->mac.type == e1000_82574) {
 		reg = er32(GCR);
drivers/net/e1000e/defines.h +7 -0
index 48f79ec..34a68fc 100644
@@ -372,6 +372,13 @@
 #define E1000_ICR_TXQ1          0x00800000 /* Tx Queue 1 Interrupt */
 #define E1000_ICR_OTHER         0x01000000 /* Other Interrupts */
 
+/* PBA ECC Register */
+#define E1000_PBA_ECC_COUNTER_MASK  0xFFF00000 /* ECC counter mask */
+#define E1000_PBA_ECC_COUNTER_SHIFT 20         /* ECC counter shift value */
+#define E1000_PBA_ECC_CORR_EN       0x00000001 /* ECC correction enable */
+#define E1000_PBA_ECC_STAT_CLR      0x00000002 /* Clear ECC error counter */
+#define E1000_PBA_ECC_INT_EN        0x00000004 /* Enable ICR bit 5 for ECC */
+
 /*
  * This defines the bits that are set in the Interrupt Mask
  * Set/Read Register.  Each bit is documented below:
drivers/net/e1000e/hw.h +1 -0
index f66ed37..c4ffd4b 100644
@@ -87,6 +87,7 @@ enum e1e_registers {
 	E1000_EEMNGCTL = 0x01010, /* MNG EEprom Control */
 	E1000_EEWR     = 0x0102C, /* EEPROM Write Register - RW */
 	E1000_FLOP     = 0x0103C, /* FLASH Opcode Register */
+	E1000_PBA_ECC  = 0x01100, /* PBA ECC Register */
 	E1000_ERT      = 0x02008, /* Early Rx Threshold - RW */
 	E1000_FCRTL    = 0x02160, /* Flow Control Receive Threshold Low - RW */
 	E1000_FCRTH    = 0x02168, /* Flow Control Receive Threshold High - RW */