WinTV HVR 1700 cannot scan (DVB-T)

Hello everyone !

I have a problem with a WinTV HVR 1700
I installed the latest available driver via mercurial and the firmware (dvb-fe- tda10048-1.0.fw).

The card seems to be well detected by its module (cx23885) as you can see in the dmesg output.
I saw there [1] that some others firmware were used (v4l-cx23885-avcore-01.fw and v4l-cx23885-enc.fw). I installed them, but I don't see when they are loaded.

I am sure of the frequencies I used because I have successfully tested on the same antenna, with the same frequencies with a WinTV Nova-T.

I do not see where the problem can come from.

[1] http://marc.info/?l=linux-dvb&m=120951119026705&w=2

Thank you very much for any help.

Simon MORIN

------

dmesg output :

Linux video capture interface: v2.00
cx23885 driver version 0.0.1 loaded
ACPI: PCI Interrupt 0000:0e:00.0[A] -> GSI 17 (level, low) -> IRQ 17 cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe bridge type 885 cx23885[0]/0: cx23885_init_tsport(portno=2)
CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700 [card=8,autodetected]
cx23885[0]/0: cx23885_pci_quirks()
cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 0x0 cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 0x0 cx23885[0]/0: cx23885_reset()
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [VID A] cx23885[0]/0: cx23885_sram_channel_setup() 0x000104c0 <- 0x00000040 cx23885[0]/0: cx23885_sram_channel_setup() 0x000104d0 <- 0x00000b80 cx23885[0]/0: cx23885_sram_channel_setup() 0x000104e0 <- 0x000016c0 cx23885[0]/0: [bridge 885] sram setup VID A: bpl=2880 lines=3 cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2] cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS1 B] cx23885[0]/0: cx23885_sram_channel_setup() 0x00010580 <- 0x00005000 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010590 <- 0x000052f0 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105a0 <- 0x000055e0 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105b0 <- 0x000058d0 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105c0 <- 0x00005bc0 cx23885[0]/0: [bridge 885] sram setup TS1 B: bpl=752 lines=5 cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5] cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS2 C] cx23885[0]/0: cx23885_sram_channel_setup() 0x000105e0 <- 0x00006000 cx23885[0]/0: cx23885_sram_channel_setup() 0x000105f0 <- 0x000062f0 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010600 <- 0x000065e0 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010610 <- 0x000068d0 cx23885[0]/0: cx23885_sram_channel_setup() 0x00010620 <- 0x00006bc0 cx23885[0]/0: [bridge 885] sram setup TS2 C: bpl=752 lines=5 cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9]

cx23885[0]: i2c scan: found device @ 0x10  [tda10048]
cx23885[0]: i2c scan: found device @ 0xa0  [eeprom]
cx23885[0]: i2c scan: found device @ 0x84  [tda8295]
cx25840' 2-0044: cx25  0-21 found @ 0x88 (cx23885[0])
cx23885[0]: i2c scan: found device @ 0x66  [???]
cx23885[0]: i2c scan: found device @ 0x88  [cx25837]
cx23885[0]: i2c scan: found device @ 0x98  [???]

tveeprom 0-0050: Hauppauge model 81519, rev B2E9, serial# 3473167 tveeprom 0-0050: MAC address is 00-0D-FE-34-FF-0F
tveeprom 0-0050: tuner model is Philips 18271_8295 (idx 149, type 54) tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
tveeprom 0-0050: audio processor is CX23885 (idx 39)
tveeprom 0-0050: decoder processor is CX23885 (idx 33)
tveeprom 0-0050: has no radio
cx23885[0]: hauppauge eeprom: model=81519
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
tda829x 1-0042: type set to tda8295
tda18271 1-0060: creating new instance
TDA18271HD/C1 detected @ 1-0060
DVB: registering new adapter (cx23885[0])
DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[0]/0: found at 0000:0e:00.0, rev: 2, irq: 17, latency: 0, mmio:
0xfde00000
PCI: Setting latency timer of device 0000:0e:00.0 to 64
tda10048_firmware_upload: waiting for firmware upload (dvb-fe- tda10048-1.0.fw)...
firmware: requesting dvb-fe-tda10048-1.0.fw
tda10048_firmware_upload: firmware read 24878 bytes.
tda10048_firmware_upload: firmware uploading
tda10048_firmware_upload: firmware uploaded
-----

Modules loaded :

#$ modprobe -v cx23885
insmod /lib/modules/2.6.26-bpo.1-686- bigmem/kernel/drivers/media/video/tveeprom.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/btcx- risc.ko
insmod /lib/modules/2.6.26-bpo.1-686- bigmem/kernel/drivers/media/video/videobuf-core.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/dvb/dvb- core/dvb-core.ko
insmod /lib/modules/2.6.26-bpo.1-686- bigmem/kernel/drivers/media/video/videobuf-dvb.ko
insmod /lib/modules/2.6.26-bpo.1-686- bigmem/kernel/drivers/media/video/videobuf-dma-sg.ko
insmod /lib/modules/2.6.26-bpo.1-686- bigmem/kernel/drivers/media/video/cx2341x.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/v4l2- compat-ioctl32.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/v4l1- compat.ko
insmod /lib/modules/2.6.26-bpo.1-686- bigmem/kernel/drivers/media/video/videodev.ko
insmod /lib/modules/2.6.26-bpo.1-686- bigmem/kernel/drivers/media/video/cx23885/cx23885.ko debug=5 i2c_scan=1

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb