driver for i5400 MCH
Subsystems (2)
PATCH RESEND 1/1 driver for i5400 MCH
EDAC driver for i5400 MCH (Seaburg)
This driver adds support for i5400 MCH chipset.
drivers/edac/Kconfig +7 -0
@@ -102,6 +102,13 @@ config EDAC_I3000 Support for error detection and correction on the Intel 3000 and 3010 server chipsets. +config EDAC_I5400 + tristate "Intel 5400 (Seaburg) chipsets" + depends on EDAC_MM_EDAC && PCI && X86 + help + Support for error detection and correction the Intel + i5400 MCH chipset (Seaburg). + config EDAC_I82860 tristate "Intel 82860" depends on EDAC_MM_EDAC && PCI && X86_32
drivers/edac/Makefile +1 -0
@@ -20,6 +20,7 @@ endif obj-$(CONFIG_EDAC_AMD76X) += amd76x_edac.o obj-$(CONFIG_EDAC_I5000) += i5000_edac.o obj-$(CONFIG_EDAC_I5100) += i5100_edac.o +obj-$(CONFIG_EDAC_I5400) += i5400_edac.o obj-$(CONFIG_EDAC_E7XXX) += e7xxx_edac.o obj-$(CONFIG_EDAC_E752X) += e752x_edac.o obj-$(CONFIG_EDAC_I82443BXGX) += i82443bxgx_edac.o
drivers/edac/i5400_edac.c new file +1471 -0
1,471 lines not on this page · raw message
Quoted 3 lines · On Mon, 1 Dec 2008 19:46:23 -0200 Mauro Carvalho Chehab…
EDAC driver for i5400 MCH (Seaburg)
This driver adds support for i5400 MCH chipset.
checkpatch has fun with this one.
Quoted 1 line
Signed-off-by Mauro Carvalho Chehab <[email protected]>
Both you and Ben Woodard are listed under MODULE_AUTHOR. Should this patch have Ben's Signed-off-by:? And/or his From:?
drivers/edac/i5400_edac.c line 60
Quoted 11 lines
...
drivers/edac/i5400_edac.c new file +8
-0+/* Device 16, +* Function 0: System Address +* Function 1: Memory Branch Map, Control, Errors Register +* Function 2: FSB Error Registers +* +* All 3 functions of Device 16 (0,1,2) share the SAME DID +*/ +#ifndef PCI_DEVICE_ID_INTEL_5400_ERR
This ifndef is unneeded: PCI_DEVICE_ID_INTEL_5400_ERR _is_ defined.
What's more, it is actually bad, because if pci_ids.h were to #define PCI_DEVICE_ID_INTEL_5400_ERR to something other than 0x4030, the ifndef would prevent the compiler from informing us of this potential problem.
drivers/edac/i5400_edac.c
Quoted 12 lines
drivers/edac/i5400_edac.c new file +9
-0+#define PCI_DEVICE_ID_INTEL_5400_ERR 0x4030/* Device 16 (0,1,2) */ +#define PCI_DEVICE_ID_INTEL_5400_FBD0 0x4035/* Device 21 (0,1) */ +#define PCI_DEVICE_ID_INTEL_5400_FBD1 0x4036/* Device 21 (0,1) */ +#endif + +/* +* Names to translate bit error into something useful +*/ +char *error_name[] = {
error_name is a global symbol.
Quoted 27 lines
drivers/edac/i5400_edac.c new file +27
-0+ [0] = "Memory Write error on non-redundant retry", + [1] = "Memory or FB-DIMM configuration CRC read error", +/* Reserved */ + [3] = "Uncorrectable Data ECC on Replay", + [4] = "Aliased Uncorrectable Non-Mirrored Demand Data ECC", +/* Unsupported on i5400 */ + [6] = "Aliased Uncorrectable Resilver- or Spare-Copy Data ECC", + [7] = "Aliased Uncorrectable Patrol Data ECC", + [8] = "Non-Aliased Uncorrectable Non-Mirrored Demand Data ECC", +/* Unsupported */ + [10] = "Non-Aliased Uncorrectable Resilver- or Spare-Copy Data ECC", + [11] = "Non-Aliased Uncorrectable Patrol Data ECC", + [12] = "Memory Write error on first attempt", + [13] = "FB-DIMM Configuration Write error on first attempt", + [14] = "Memory or FB-DIMM configuration CRC read error", + [15] = "Channel Failed-Over Occurred", + [16] = "Correctable Non-Mirrored Demand Data ECC", +/* Unsupported */ + [18] = "Correctable Resilver- or Spare-Copy Data ECC", + [19] = "Correctable Patrol Data ECC", + [20] = "FB-DIMM Northbound parity error on FB-DIMM Sync Status", + [21] = "SPD protocol Error", + [22] = "Non-Redundant Fast Reset Timeout", + [23] = "Refresh error", + [24] = "Memory Write error on redundant retry", + [25] = "Redundant Fast Reset Timeout", + [26] = "Correctable Counter Threshold Exceeded",
drivers/edac/i5400_edac.c line 263
Quoted 10 lines
drivers/edac/i5400_edac.c new file +7
-0+ [27] = "DIMM-Spare Copy Completed", + [28] = "DIMM-Isolation Completed", +}; + +/* masks for non-fatal error register */ +#define TO_NF_MASK (a) (((a) & EMASK_M29) | ((a) >> 3)) +#define FROM_NF_FERR (a) (((a) & EMASK_M29) | (((a) << 3) & ((1 << 30)-1)))
These macros will misbehave if passed an expression with side-effects. Not really a problem as they're only used for constructing constants. I guess if one was being paranoid, one could #undef them again as soon as possible.
Quoted 17 lines
drivers/edac/i5400_edac.c new file +14
-0+#define FERR_NF_MASK TO_NF_MASK(ERROR_NF_MASK) +#define FERR_NF_CORRECTABLE TO_NF_MASK(ERROR_NF_CORRECTABLE) +#define FERR_NF_DIMM_SPARE TO_NF_MASK(ERROR_NF_DIMM_SPARE) +#define FERR_NF_SPD_PROTOCOL TO_NF_MASK(ERROR_NF_SPD_PROTOCOL) +#define FERR_NF_NORTH_CRC TO_NF_MASK(ERROR_NF_NORTH_CRC) +#define FERR_NF_RECOVERABLE TO_NF_MASK(ERROR_NF_RECOVERABLE) +#define FERR_NF_UNCORRECTABLE TO_NF_MASK(ERROR_NF_UNCORRECTABLE) + +#ifdef CONFIG_EDAC_DEBUG +/* MTR NUMROW */ +static char *numrow_toString[] = { +"8,192 - 13 rows" , +"16,384 - 14 rows" , + "32,768 - 15 rows",
drivers/edac/i5400_edac.c line 309
Quoted 10 lines
drivers/edac/i5400_edac.c new file +10
-0+ "65,536 - 16 rows" +}; + +/* MTR NUMCOL */ +static char *numcol_toString[] = { +"1,024 - 10 columns" , +"2,048 - 11 columns" , +"4,096 - 12 columns" , +"reserved" +};
These could possibly be made const. We don't modify them at runtime...
drivers/edac/i5400_edac.c line 519
Quoted 10 lines
drivers/edac/i5400_edac.c new file +7
-0+#endif + +static void i5400_proccess_non_recoverable_info (struct mem_ctl_info *mci, +struct i5400_error_info *info, +unsigned long allErrors) +{ +char msg[EDAC_MC_LABEL_LEN +1 +90 +80 ];
202 bytes. Tolerable, I guess.
Heaven knows why and how this dimension was chosen, and under which circumstances it will overflow :(
It looks like such a hack that perhaps you should give up and use kasprintf()+kfree()?
Quoted 53 lines
drivers/edac/i5400_edac.c new file +53
-0+int branch; +int channel; +int bank; +int buf_id; +int rank; +int rdwr; +int ras, cas; +int errnum; +char *type =NULL ; + +if (!allErrors) +return ;/* if no error, return now */ + +if (allErrors &ERROR_FAT_MASK ) + type ="FATAL" ; +else if (allErrors &FERR_NF_UNCORRECTABLE ) + type ="NON-FATAL uncorrected" ; +else + type ="NON-FATAL recoverable" ; + +/* ONLY ONE of the possible error bits will be set, as per the docs */ + + branch =extract_fbdchan_indx (info->ferr_fat_fbd); + channel = branch; + +/* Use the NON-Recoverable macros to extract data */ + bank =nrec_bank (info); + rank =nrec_rank (info); + buf_id =nrec_buf_id (info); + rdwr =nrec_rdwr (info); + ras =nrec_ras (info); + cas =nrec_cas (info); + +debugf0 ("\t\tCSROW= %d Channels= %d,%d (Branch= %d " +"DRAM Bank= %d Buffer ID = %d rdwr= %s ras= %d cas= %d)\n" , + rank, channel, channel +1 , branch >>1 , bank, + buf_id,rdwr_str (rdwr), ras, cas); + +/* Only 1 bit will be on */ + errnum =find_first_bit (&allErrors,ARRAY_SIZE (error_name)); + +/* Form out message */ +snprintf (msg,sizeof (msg), +"%s (Branch=%d DRAM-Bank=%d Buffer ID = %d RDWR=%s RAS=%d CAS=%d " +"%s Err=0x%lx (%s))" , + type, branch >>1 , bank, buf_id,rdwr_str (rdwr), ras, cas, type, + allErrors, error_name[errnum]); + +/* Call the helper to output message */ +edac_mc_handle_fbd_ue (mci, rank, channel, channel +1 , msg); +} + +/*
drivers/edac/i5400_edac.c line 582
Quoted 10 lines
drivers/edac/i5400_edac.c new file +10
-0+* i5400_process_fatal_error_info(struct mem_ctl_info *mci, +* struct i5400_error_info *info, +* int handle_errors); +* +* handle the Intel NON-FATAL errors, if any +*/ +static void i5400_process_nonfatal_error_info (struct mem_ctl_info *mci, +struct i5400_error_info *info) +{ +char msg[EDAC_MC_LABEL_LEN +1 +90 +80 ];
dittoes.
Quoted 83 lines
drivers/edac/i5400_edac.c new file +80
-0+unsigned long allErrors; +int branch; +int channel; +int bank; +int rank; +int rdwr; +int ras, cas; +int errnum; + +/* mask off the Error bits that are possible */ + allErrors =FROM_NF_FERR (info->ferr_nf_fbd &FERR_NF_MASK ); +if (!allErrors) +return ;/* if no error, return now */ + +/* ONLY ONE of the possible error bits will be set, as per the docs */ + +if (allErrors & (ERROR_NF_UNCORRECTABLE |ERROR_NF_RECOVERABLE )) { +i5400_proccess_non_recoverable_info (mci, info, allErrors); +return ; + } + +/* Correctable errors */ +if (allErrors &ERROR_NF_CORRECTABLE ) { +debugf0 ("\tCorrected bits= 0x%lx\n" , allErrors); + + branch =extract_fbdchan_indx (info->ferr_nf_fbd); + + channel =0 ; +if (REC_ECC_LOCATOR_ODD (info->redmemb)) + channel =1 ; + +/* Convert channel to be based from zero, instead of +* from branch base of 0 */ + channel += branch; + + bank =rec_bank (info); + rank =rec_rank (info); + rdwr =rec_rdwr (info); + ras =rec_ras (info); + cas =rec_cas (info); + +/* Only 1 bit will be on */ + errnum =find_first_bit (&allErrors,ARRAY_SIZE (error_name)); + +debugf0 ("\t\tCSROW= %d Channel= %d (Branch %d " +"DRAM Bank= %d rdwr= %s ras= %d cas= %d)\n" , + rank, channel, branch >>1 , bank, +rdwr_str (rdwr), ras, cas); + +/* Form out message */ +snprintf (msg,sizeof (msg), +"Corrected error (Branch=%d DRAM-Bank=%d RDWR=%s RAS=%d " +"CAS=%d, CE Err=0x%lx (%s))" , branch >>1 , bank, +rdwr_str (rdwr), ras, cas, allErrors, + error_name[errnum]); + +/* Call the helper to output message */ +edac_mc_handle_fbd_ce (mci, rank, channel, msg); + +return ; + } + +/* Miscelaneous errors */ + errnum =find_first_bit (&allErrors,ARRAY_SIZE (error_name)); + + branch =extract_fbdchan_indx (info->ferr_nf_fbd); + +i5400_mc_printk (mci,KERN_EMERG , +"Non-Fatal misc error (Branch=%d Err=%#lx (%s))" , + branch >>1 , allErrors, error_name[errnum]); +} + +static void i5400_put_devices (struct mem_ctl_info *mci) +{ +struct i5400_pvt *pvt; + + pvt = mci->pvt_info; + +/* Decrement usage count for devices */ +if (pvt->branch_1)
drivers/edac/i5400_edac.c line 717
Quoted 10 lines
drivers/edac/i5400_edac.c new file +10
-0+pci_dev_put (pvt->branch_1); + +if (pvt->branch_0) +pci_dev_put (pvt->branch_0); + +if (pvt->fsb_error_regs) +pci_dev_put (pvt->fsb_error_regs); + +if (pvt->branchmap_werrors) +pci_dev_put (pvt->branchmap_werrors);
pci_dev_put(NULL) is legal.
Quoted 61 lines
drivers/edac/i5400_edac.c new file +58
-0+} + +static int i5400_probe1 (struct pci_dev *pdev,int dev_idx) +{ +struct mem_ctl_info *mci; +struct i5400_pvt *pvt; +int num_channels; +int num_dimms_per_channel; +int num_csrows; + +debugf0 ("MC: " __FILE__": %s(), pdev bus %u dev=0x%x fn=0x%x\n" , + __func__, + pdev->bus->number, +PCI_SLOT (pdev->devfn),PCI_FUNC (pdev->devfn)); + +/* We only are looking for func 0 of the set */ +if (PCI_FUNC (pdev->devfn) !=0 ) +return -ENODEV ; + +/* Ask the devices for the number of CSROWS and CHANNELS so +* that we can calculate the memory resources, etc +* +* The Chipset will report what it can handle which will be greater +* or equal to what the motherboard manufacturer will implement. +* +* As we don't have a motherboard identification routine to determine +* actual number of slots/dimms per channel, we thus utilize the +* resource as specified by the chipset. Thus, we might have +* have more DIMMs per channel than actually on the mobo, but this +* allows the driver to support upto the chipset max, without +* some fancy mobo determination. +*/ +i5400_get_dimm_and_channel_counts (pdev, &num_dimms_per_channel, + &num_channels); + num_csrows = num_dimms_per_channel *2 ; + +debugf0 ("MC: %s(): Number of - Channels= %d DIMMS= %d CSROWS= %d\n" , + __func__, num_channels, num_dimms_per_channel, num_csrows); + +/* allocate a new MC control structure */ + mci =edac_mc_alloc (sizeof (*pvt), num_csrows, num_channels,0 ); + +if (mci ==NULL ) +return -ENOMEM ; + +debugf0 ("MC: " __FILE__": %s(): mci = %p\n" , __func__, mci); + + mci->dev = &pdev->dev;/* record ptr to the generic device */ + + pvt = mci->pvt_info; + pvt->system_address = pdev;/* Record this device in our private */ + pvt->maxch = num_channels; + pvt->maxdimmperch = num_dimms_per_channel; + +/* 'get' the pci devices we want to reserve for our use */ +if (i5400_get_devices (mci, dev_idx)) + goto fail0; +
drivers/edac/i5400_edac.c line 1311
Quoted 10 lines
drivers/edac/i5400_edac.c new file +10
-0+/* Time to get serious */ +i5400_get_mc_regs (mci);/* retrieve the hardware registers */ + + mci->mc_idx =0 ; + mci->mtype_cap =MEM_FLAG_FB_DDR2 ; + mci->edac_ctl_cap =EDAC_FLAG_NONE ; + mci->edac_cap =EDAC_FLAG_NONE ; + mci->mod_name ="i5400_edac.c" ; + mci->mod_ver =I5400_REVISION ; + mci->ctl_name = i5400_devs[dev_idx].ctl_name;
This is a bit strange. i5400_devs[] has a single entry, so what's the point in indexing it with `dev_idx', which MUST have a value of zero anyway?
Quoted 52 lines
drivers/edac/i5400_edac.c new file +52
-0+ mci->dev_name =pci_name (pdev); + mci->ctl_page_to_phys =NULL ; + +/* Set the function pointer to an actual operation function */ + mci->edac_check = i5400_check_error; + +/* initialize the MC control structure 'csrows' table +* with the mapping and control information */ +if (i5400_init_csrows (mci)) { +debugf0 ("MC: Setting mci->edac_cap to EDAC_FLAG_NONE\n" +" because i5400_init_csrows() returned nonzero " +"value\n" ); + mci->edac_cap =EDAC_FLAG_NONE ;/* no csrows found */ + }else { +debugf1 ("MC: Enable error reporting now\n" ); +i5400_enable_error_reporting (mci); + } + +/* add this new MC control structure to EDAC's list of MCs */ +if (edac_mc_add_mc (mci)) { +debugf0 ("MC: " __FILE__ +": %s(): failed edac_mc_add_mc()\n" , __func__); +/* FIXME: perhaps some code should go here that disables error +* reporting if we just enabled it +*/ + goto fail1; + } + +i5400_clear_error (mci); + +/* allocating generic PCI control info */ + i5400_pci =edac_pci_create_generic_ctl (&pdev->dev,EDAC_MOD_STR ); +if (!i5400_pci) { +printk (KERN_WARNING +"%s(): Unable to create PCI control\n" , + __func__); +printk (KERN_WARNING +"%s(): PCI error report via EDAC not setup\n" , + __func__); + } + +return 0 ; + +/* Error exit unwinding stack */ +fail1: + +i5400_put_devices (mci); + +fail0: +edac_mc_free (mci); +return -ENODEV ; +}
drivers/edac/i5400_edac.c line 1432
Quoted 10 lines
drivers/edac/i5400_edac.c new file +7
-0+ +static struct pci_driver i5400_driver = { + .name =KBUILD_BASENAME , + .probe = i5400_init_one, + .remove =__devexit_p (i5400_remove_one), + .id_table = i5400_pci_tbl, +};
Only one other driver in the tree uses KBUILD_BASENAME, and that is drivers/edac/i5100_edac.c, from which I suspect the above was copied.
I suspect that something is being done wrongly here.
Quoted 3 lines
...
Quoted 7 lines · On Tue, 2 Dec 2008 22:33:47 -0800 Andrew Morton <[email protected]>…
Quoted 3 lines · On Mon, 1 Dec 2008 19:46:23 -0200 Mauro Carvalho Chehab…
EDAC driver for i5400 MCH (Seaburg)
This driver adds support for i5400 MCH chipset.
checkpatch has fun with this one.
Ok. I fixed the remaining errors.
I'll just keep the 80 char warns on lines with comments explaining each field, like:
WARNING: line over 80 characters
#200: FILE: drivers/edac/i5400_edac.c:151:
+ EMASK_M9 = 1<<8, /* Non-Aliased Uncorrectable Non-Mirrored Demand Data ECC */
Where breaking the line wouldn't be that fun.
Quoted 4 lines
Quoted 1 line
Signed-off-by Mauro Carvalho Chehab <[email protected]>Both you and Ben Woodard are listed under
MODULE_AUTHOR. Should this patch have Ben's Signed-off-by:? And/or his From:?
I'll ask his SOB.
Quoted 7 lines
Quoted 1 line
+#ifndef
PCI_DEVICE_ID_INTEL_5400_ERRThis ifndef is unneeded:
PCI_DEVICE_ID_INTEL_5400_ERR_is_ defined.What's more, it is actually bad, because if
pci_ids.hwere to #definePCI_DEVICE_ID_INTEL_5400_ERRto something other than0x4030, the ifndef would prevent the compiler from informing us of this potential problem.
Fixed.
Quoted 3 lines
Quoted 1 line
+char *error_name[] = {
error_nameis a global symbol.
Changed. Also changed it to const.
Quoted 8 lines
drivers/edac/i5400_edac.c line 263
Quoted 3 lines
drivers/edac/i5400_edac.c new file +3
-0+/* masks for non-fatal error register */ +#define TO_NF_MASK (a) (((a) & EMASK_M29) | ((a) >> 3)) +#define FROM_NF_FERR (a) (((a) & EMASK_M29) | (((a) << 3) & ((1 << 30)-1)))These macros will misbehave if passed an expression with side-effects. Not really a problem as they're only used for constructing constants. I guess if one was being paranoid, one could #undef them again as soon as possible.
Good point. I've converted both macros into inline functions, since gcc will likely optimize the code into a constant, instead of calculating at runtime.
Quoted 10 lines
Quoted 10 lines
drivers/edac/i5400_edac.c new file +10
-0+#ifdef CONFIG_EDAC_DEBUG +/* MTR NUMROW */ +static char *numrow_toString[] = { +"8,192 - 13 rows" , +"16,384 - 14 rows" , +"32,768 - 15 rows" , +"65,536 - 16 rows" +}; + +/* MTR NUMCOL */
Quoted 8 lines
drivers/edac/i5400_edac.c line 309
Quoted 6 lines
drivers/edac/i5400_edac.c new file +6
-0+static char *numcol_toString[] = { +"1,024 - 10 columns" , +"2,048 - 11 columns" , +"4,096 - 12 columns" , +"reserved" +};These could possibly be made const. We don't modify them at runtime...
Fixed.
Quoted 7 lines
202 bytes. Tolerable, I guess.
Heaven knows why and how this dimension was chosen, and under which circumstances it will overflow :(
It looks like such a hack that perhaps you should give up and use kasprintf()+kfree()?
I also didn't like that code. It is present also on other edac drivers.
I'll fix this on a later patch. I'll probably propose some patches to the other edac drivers that use this kind of construction.
Quoted 6 lines
Quoted 6 lines
drivers/edac/i5400_edac.c new file +6
-0+/* Decrement usage count for devices */ +if (pvt->branch_1) +pci_dev_put (pvt->branch_1); + +if (pvt->branch_0) +pci_dev_put (pvt->branch_0);
Quoted 8 lines
drivers/edac/i5400_edac.c line 717
Quoted 6 lines
drivers/edac/i5400_edac.c new file +6
-0+ +if (pvt->fsb_error_regs) +pci_dev_put (pvt->fsb_error_regs); + +if (pvt->branchmap_werrors) +pci_dev_put (pvt->branchmap_werrors);
pci_dev_put(NULL)is legal.
Fixed.
Quoted 5 lines
drivers/edac/i5400_edac.c line 1311
Quoted 1 line
drivers/edac/i5400_edac.c new file +1
-0+ mci->ctl_name = i5400_devs[dev_idx].ctl_name;This is a bit strange. i5400_devs[] has a single entry, so what's the point in indexing it with `dev_idx', which MUST have a value of zero anyway?
I'm not sure if we covered all PCI ID's for i5400 (maybe some i5400 variant may be released?). That's why I preferred to keep a table: makes easier to add other entries there, but I see your point.
I'll add a code to prevent dev_idx values equal or higher than ARRAY_SIZE, to avoid the risk of trying to acess something outside the buffer.
Quoted 11 lines
drivers/edac/i5400_edac.c line 1432
Quoted 6 lines
drivers/edac/i5400_edac.c new file +6
-0+static struct pci_driver i5400_driver = { + .name =KBUILD_BASENAME , + .probe = i5400_init_one, + .remove =__devexit_p (i5400_remove_one), + .id_table = i5400_pci_tbl, +};Only one other driver in the tree uses
KBUILD_BASENAME, and that isdrivers/edac/i5100_edac.c, from which I suspect the above was copied.I suspect that something is being done wrongly here.
Fixed.
I'll run some tests here, and submit a version 2 of the patch soon.
Cheers,
Mauro
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 5 lines · Andrew Morton
Quoted 2 lines
Signed-off-by Mauro Carvalho Chehab <[email protected]>Both you and Ben Woodard are listed under
MODULE_AUTHOR. Should this patch have Ben's Signed-off-by:? And/or his From:?
Go ahead and add a:
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (GNU/Linux)
Comment: Using GnuPG with Red Hat - http://enigmail.mozdev.org
iD8DBQFJNufYYuGAPpw3tAARAlA5AJ4hNh6Mzzs60atqL06MkoD7RulsbwCdGSP7 DIQiX8F4+1eQXYeZPSQkc0M=
=anBc
-----END PGP SIGNATURE-----
PATCH v2 1/1 edac: driver for i5400 MCH (Seaburg)
From: Mauro Carvalho Chehab <[email protected]>
This patch adds a driver for support errors reported by i5400 MCH chipset (Seaburg)
drivers/edac/Kconfig +7 -0
@@ -109,6 +109,13 @@ config EDAC_X38 Support for error detection and correction on the Intel X38 server chipsets. +config EDAC_I5400 + tristate "Intel 5400 (Seaburg) chipsets" + depends on EDAC_MM_EDAC && PCI && X86 + help + Support for error detection and correction the Intel + i5400 MCH chipset (Seaburg). + config EDAC_I82860 tristate "Intel 82860" depends on EDAC_MM_EDAC && PCI && X86_32
drivers/edac/Makefile +1 -0
@@ -20,6 +20,7 @@ endif obj-$(CONFIG_EDAC_AMD76X) += amd76x_edac.o obj-$(CONFIG_EDAC_I5000) += i5000_edac.o obj-$(CONFIG_EDAC_I5100) += i5100_edac.o +obj-$(CONFIG_EDAC_I5400) += i5400_edac.o obj-$(CONFIG_EDAC_E7XXX) += e7xxx_edac.o obj-$(CONFIG_EDAC_E752X) += e752x_edac.o obj-$(CONFIG_EDAC_I82443BXGX) += i82443bxgx_edac.o
drivers/edac/i5400_edac.c new file +1476 -0
1,476 lines not on this page · raw message