usb : musb : Add MUSB contorller driver and enable Davinci MSC support
v3 cover usb : musb : Add MUSB contorller driver and enable Davinci MSC support
This patch series adds Mentor Graphics USB OTG host controller driver support and MSC support for DM6446 (TI DaVinci) platform.
- [PATCH v3 1/5] usb : musb : Adding host controller driver for Mentor USB controller.
- [PATCH v3 2/5] usb : musb : Adding USB VBUS enable functionality for DM6446 DVEVM.
- [PATCH v3 3/5] usb : musb : Adding DM6446 (TI DaVinci) platform specific USB support.
- [PATCH v3 4/5] usb : musb : Enabling DM6446 (TI DaVinci) USB module power.
- [PATCH v3 5/5] usb : musb : Enabling USB MSC support for DM6446 (TI DaVinci) platform.
Note: This patch series depends on the following patch submitted by Michael Trimarchi.
- [U-Boot] [USB PATCH] USB change speed
Changes since v2:
- Addressed changes suggested by Dirk Behme
- Added register overlay structure to access mentor USB module registers
Changes since v1:
- Rebased to U-Boot USB next branch
- Removed high element from usb_device structure
v3 cover usb : musb : Add MUSB contorller driver and enable Davinci MSC support
Quoted 9 lines · Thomas Abraham
This patch series adds Mentor Graphics USB OTG host controller driver support and MSC support for DM6446 (TI DaVinci) platform.
- [PATCH v3 1/5] usb : musb : Adding host controller driver for Mentor USB controller.
- [PATCH v3 2/5] usb : musb : Adding USB VBUS enable functionality for DM6446 DVEVM.
- [PATCH v3 3/5] usb : musb : Adding DM6446 (TI DaVinci) platform specific USB support.
- [PATCH v3 4/5] usb : musb : Enabling DM6446 (TI DaVinci) USB module power.
- [PATCH v3 5/5] usb : musb : Enabling USB MSC support for DM6446 (TI DaVinci) platform.
Quoted 8 lines
Note: This patch series depends on the following patch submitted by Michael Trimarchi.
- [U-Boot] [USB PATCH] USB change speed
Changes since v2:
- Addressed changes suggested by Dirk Behme
which one no comment have been send to the ML?
Best Regards,
J.
Abraham
v3 cover usb : musb : Add MUSB contorller driver and enable Davinci MSC support
Jean,
Quoted 5 lines
-----Original Message-----
From: Jean-Christophe PLAGNIOL-VILLARD [mailto:plagnioj at jcrosoft.com]
Sent: Sunday, January 04, 2009 12:51 PM
Subject: Re: [U-Boot] [PATCH v3 0/5] usb : musb : Add MUSB contorller driver and enable Davinci MSC support
<snip>
Quoted 4 lines
Quoted 3 lines
Changes since v2:
- Addressed changes suggested by Dirk Behme
which one no comment have been send to the ML?
It somehow missed being posted to the mailing list.
Quoted 3 lines
Best Regards,
J.
Thanks,
Thomas.
v3 cover usb : musb : Add MUSB contorller driver and enable Davinci MSC support
In reply to Thomas AbrahamQuoted 2 lines · On Saturday 03 January 2009 23:10:26 Thomas Abraham wrote:
This patch series adds Mentor Graphics USB OTG host controller driver support and MSC support for DM6446 (TI DaVinci) platform.
do you have a git tree or you just using the u-boot usb next git tree ?
also, what about the feedback Bryan sent you ? i glanced at the comments he made and the source is unchanged from what i can see.
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 835 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20090104/39a8fade/attachment.pgp
Abraham
v3 cover usb : musb : Add MUSB contorller driver and enable Davinci MSC support
Mike,
Quoted 5 lines
-----Original Message-----
From: Mike Frysinger [mailto:vapier at gentoo.org]
Sent: Sunday, January 04, 2009 11:00 PM
Subject: Re: [U-Boot] [PATCH v3 0/5] usb : musb : Add MUSB contorller driver and enable Davinci MSC support
<snip>
Quoted 3 lines
do you have a git tree or you just using the u-boot usb next git tree ?
The Davinci USB patches are against the U-Boot USB 'next' branch.
Quoted 4 lines
also, what about the feedback Bryan sent you ? i glanced at the comments he made and the source is unchanged from what i can see. -mike
I am sorry for having missed the feedback from Bryan (did not read the emails received during vacation). I will included his comments as well.
Thanks,
Thomas.
v3 cover usb : musb : Add MUSB contorller driver and enable Davinci MSC support
In reply to Thomas AbrahamHello Thomas,
2009/1/4 Thomas Abraham <[email protected]>:
Quoted 9 lines
This patch series adds Mentor Graphics USB OTG host controller driver support and MSC support for DM6446 (TI DaVinci) platform.
- [PATCH v3 1/5] usb : musb : Adding host controller driver for Mentor USB controller.
- [PATCH v3 2/5] usb : musb : Adding USB VBUS enable functionality for DM6446 DVEVM.
- [PATCH v3 3/5] usb : musb : Adding DM6446 (TI DaVinci) platform specific USB support.
- [PATCH v3 4/5] usb : musb : Enabling DM6446 (TI DaVinci) USB module power.
- [PATCH v3 5/5] usb : musb : Enabling USB MSC support for DM6446 (TI DaVinci) platform.
Before I loose track of all the versionnumbers of all the different series that are somehow dependant on each other, I moved this series to the 'testing' branch of u-boot-usb.
I leave the door open for an update of this series when there are major comments on it.
Kind Regards,
Remy
Quoted 20 lines
Note: This patch series depends on the following patch submitted by Michael Trimarchi.
- [U-Boot] [USB PATCH] USB change speed
Changes since v2:
- Addressed changes suggested by Dirk Behme
- Added register overlay structure to access mentor USB module registersChanges since v1:
- Rebased to U-Boot USB next branch
- Removed high element fromusb_devicestructure_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
v3 cover usb : musb : Add MUSB contorller driver and enable Davinci MSC support
In reply to Thomas AbrahamHi Thomas,
I'm still debugging the MUSB driver on my Blackfin board. I got a issue here:
https://blackfin.uclinux.org/gf/project/u-boot/tracker/?action=TrackerItemEdit&tracker_id=153&tracker_item_id=4794
1. when the board power on and run 'usb start', the usb function is ok for usb storage usage.
2. then I tried 'usb stop'. and run 'usb start' again. usb device cannot be found.
Is that OK on davinci or omap platform?
Thanks
-Bryan
Quoted 29 lines · Thomas Abraham
This patch series adds Mentor Graphics USB OTG host controller driver support and MSC support for DM6446 (TI DaVinci) platform.
- [PATCH v3 1/5] usb : musb : Adding host controller driver for Mentor USB controller.
- [PATCH v3 2/5] usb : musb : Adding USB VBUS enable functionality for DM6446 DVEVM.
- [PATCH v3 3/5] usb : musb : Adding DM6446 (TI DaVinci) platform specific USB support.
- [PATCH v3 4/5] usb : musb : Enabling DM6446 (TI DaVinci) USB module power.
- [PATCH v3 5/5] usb : musb : Enabling USB MSC support for DM6446 (TI DaVinci) platform.Note: This patch series depends on the following patch submitted by Michael Trimarchi.
- [U-Boot] [USB PATCH] USB change speed
Changes since v2:
- Addressed changes suggested by Dirk Behme
- Added register overlay structure to access mentor USB module registersChanges since v1:
- Rebased to U-Boot USB next branch
- Removed high element fromusb_devicestructure_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Abraham
v3 cover usb : musb : Add MUSB contorller driver and enable Davinci MSC support
Hi Bryan,
Sorry for the delayed reply. The sequence 'usb start' -> 'usb stop' -> 'usb start' works fine on Davinci and OMAP platforms.
Thanks,
Thomas.
Quoted 67 lines
-----Original Message-----
From: cooloney.lkml at gmail.com [mailto:cooloney.lkml at gmail.com] On Behalf Of Bryan Wu
Sent: Thursday, January 15, 2009 2:16 PM
To: Abraham, Thomas
Cc: u-boot at lists.denx.de; Gupta, Ajay Kumar; Subbrathnam, Swaminathan; B, Ravi
Subject: Re: [U-Boot] [PATCH v3 0/5] usb : musb : Add MUSB contorller driver and enable Davinci MSC supportHi Thomas,
I'm still debugging the MUSB driver on my Blackfin board. I got a issue here:
https://blackfin.uclinux.org/gf/project/u-boot/tracker/?action
=TrackerItemEdit&tracker_id=153&tracker_item_id=47941. when the board power on and run 'usb start', the usb function is ok for usb storage usage.
2. then I tried 'usb stop'. and run 'usb start' again. usb device cannot be found.Is that OK on davinci or omap platform?
Thanks
-BryanQuoted 1 line · Thomas Abraham
This patch series adds Mentor Graphics USB OTG host
controller driver
Quoted 3 lines
support and MSC support for DM6446 (TI DaVinci) platform.
- [PATCH v3 1/5] usb : musb : Adding host controller driver
for Mentor USB controller.
Quoted 1 line
- [PATCH v3 2/5] usb : musb : Adding USB VBUS enable
functionality for DM6446 DVEVM.
Quoted 1 line
- [PATCH v3 3/5] usb : musb : Adding DM6446 (TI DaVinci)
platform specific USB support.
Quoted 1 line
- [PATCH v3 4/5] usb : musb : Enabling DM6446 (TI DaVinci)
USB module power.
Quoted 1 line
- [PATCH v3 5/5] usb : musb : Enabling USB MSC support for
DM6446 (TI DaVinci) platform.
Quoted 22 lines
Note: This patch series depends on the following patch submitted by Michael Trimarchi.
- [U-Boot] [USB PATCH] USB change speed
Changes since v2:
- Addressed changes suggested by Dirk Behme
- Added register overlay structure to access mentor USB module registersChanges since v1:
- Rebased to U-Boot USB next branch
- Removed high element fromusb_devicestructure_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
v3 cover usb : musb : Add MUSB contorller driver and enable Davinci MSC support
Quoted 5 lines · Thomas
Hi Bryan,
Sorry for the delayed reply. The sequence 'usb start' -> 'usb stop' -> 'usb start' works fine on Davinci and OMAP platforms.
Thanks for the reply. And 2 more questions:
- there is no timeout control in the wait_until_xxx_ready() functions, so when there no device plugged in u-boot will hang in these endless loops.
- there is no root hub control, so we cannot use 'usb info' to get device 0 root hub config info
do you have any plan to add these?
Best Regards,
-Bryan
Quoted 71 lines
Thanks,
Thomas.Quoted 67 lines
-----Original Message-----
From: cooloney.lkml at gmail.com [mailto:cooloney.lkml at gmail.com] On Behalf Of Bryan Wu
Sent: Thursday, January 15, 2009 2:16 PM
To: Abraham, Thomas
Cc: u-boot at lists.denx.de; Gupta, Ajay Kumar; Subbrathnam, Swaminathan; B, Ravi
Subject: Re: [U-Boot] [PATCH v3 0/5] usb : musb : Add MUSB contorller driver and enable Davinci MSC supportHi Thomas,
I'm still debugging the MUSB driver on my Blackfin board. I got a issue here:
https://blackfin.uclinux.org/gf/project/u-boot/tracker/?action
=TrackerItemEdit&tracker_id=153&tracker_item_id=47941. when the board power on and run 'usb start', the usb function is ok for usb storage usage.
2. then I tried 'usb stop'. and run 'usb start' again. usb device cannot be found.Is that OK on davinci or omap platform?
Thanks
-BryanQuoted 1 line · Thomas Abraham
This patch series adds Mentor Graphics USB OTG host
controller driver
Quoted 3 lines
support and MSC support for DM6446 (TI DaVinci) platform.
- [PATCH v3 1/5] usb : musb : Adding host controller driver
for Mentor USB controller.
Quoted 1 line
- [PATCH v3 2/5] usb : musb : Adding USB VBUS enable
functionality for DM6446 DVEVM.
Quoted 1 line
- [PATCH v3 3/5] usb : musb : Adding DM6446 (TI DaVinci)
platform specific USB support.
Quoted 1 line
- [PATCH v3 4/5] usb : musb : Enabling DM6446 (TI DaVinci)
USB module power.
Quoted 1 line
- [PATCH v3 5/5] usb : musb : Enabling USB MSC support for
DM6446 (TI DaVinci) platform.
Quoted 22 lines
Note: This patch series depends on the following patch submitted by Michael Trimarchi.
- [U-Boot] [USB PATCH] USB change speed
Changes since v2:
- Addressed changes suggested by Dirk Behme
- Added register overlay structure to access mentor USB module registersChanges since v1:
- Rebased to U-Boot USB next branch
- Removed high element fromusb_devicestructure_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot