Skip to contentSkip to conversation

ide: remove unused CONFIG_BLK_DEV_IDE_AU1-[Triple-X]_SEQTS_PER_RQ

PATCH RESEND In review Bartlomiej Zolnierkiewicz 2 participants 2 messages Jan 6, 2009 – Jan 11, 2009

Subsystems (2)
Documentation libata
lore
Share & tools
lore

Bartlomiej Zolnierkiewicz

author
#0 lore raw

PATCH RESEND 3/9 ide: remove unused CONFIG_BLK_DEV_IDE_AU1-[Triple-X]_SEQTS_PER_RQ

Reason for resend: vger doesn't like XXX

This is an automatically generated Delivery Status Notification

Delivery to the following recipient failed permanently:

[email protected]

Technical details of permanent failure:
Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550 5.7.1 Content-Policy reject msg: The capital Triple-X in subject is way too often associated with junk email, please rephrase. BF:<H 6.15064e-14>; S1754791AbZAFSev (state 18).

From: Bartlomiej Zolnierkiewicz <[email protected]>
Subject: [PATCH] ide: remove unused CONFIG_BLK_DEV_IDE_AU1_XXX_SEQTS_PER_RQ

Signed-off-by Bartlomiej Zolnierkiewicz <[email protected]>

---
AU1xxx_IDE.README needs more (out of scope for this patch) updates.

 Documentation/mips/AU1xxx_IDE.README |    6 +-----
 drivers/ide/Kconfig                  |    5 -----
 2 files changed, 1 insertion(+), 10 deletions(-)
Documentation/mips/AU1xxx_IDE.README +1 -5
Index: b/Documentation/mips/AU1xxx_IDE.README
===================================================================
@@ -52,14 +52,12 @@ Two files are introduced:
   b) 'drivers/ide/mips/au1xxx-ide.c'
      contains the functionality of the AU1XXX IDE driver
 
-Four configs variables are introduced:
+Following extra configs variables are introduced:
 
   CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA    - enable the PIO+DBDMA mode
   CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA  - enable the MWDMA mode
   CONFIG_BLK_DEV_IDE_AU1XXX_BURSTABLE_ON - set Burstable FIFO in DBDMA
                                            controller
-  CONFIG_BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ - maximum transfer size
-                                           per descriptor
 
 
 SUPPORTED IDE MODES

@@ -87,7 +85,6 @@ CONFIG_BLK_DEV_IDEDMA_PCI=y
 CONFIG_IDEDMA_PCI_AUTO=y
 CONFIG_BLK_DEV_IDE_AU1XXX=y
 CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=y
-CONFIG_BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ=128
 CONFIG_BLK_DEV_IDEDMA=y
 CONFIG_IDEDMA_AUTO=y
 

@@ -105,7 +102,6 @@ CONFIG_BLK_DEV_IDEDMA_PCI=y
 CONFIG_IDEDMA_PCI_AUTO=y
 CONFIG_BLK_DEV_IDE_AU1XXX=y
 CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=y
-CONFIG_BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ=128
 CONFIG_BLK_DEV_IDEDMA=y
 CONFIG_IDEDMA_AUTO=y
drivers/ide/Kconfig +0 -5
Index: b/drivers/ide/Kconfig
===================================================================
@@ -701,11 +701,6 @@ config BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
        depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
 endchoice
 
-config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
-       int "Maximum transfer size (KB) per request (up to 128)"
-       default "128"
-       depends on BLK_DEV_IDE_AU1XXX
-
 config BLK_DEV_IDE_TX4938
 	tristate "TX4938 internal IDE support"
 	depends on SOC_TX4938