Omap fixes for 2.6.29-rc1
Subsystems (6)
Tony Lindgren
maintainercover Omap fixes for 2.6.29-rc1
Hi,
Here are some omap fixes for review. Some of these patches were posted earlier.
Regards,
Tony
---
Anand Gadiyar (1):
ARM: OMAP: Fix DMA CCR programming for request line > 63
Arun KS (1):
ARM: OMAP: Fix OSK ASoC by registering I2C board info for tlvaic23
Huang Weiyi (1):
ARM: OMAP: remove duplicated #include's
Jarkko Nikula (1):
ARM: OMAP: Fix gpio by switching to generic gpio calls, v2
Tony Lindgren (6):
ARM: OMAP: Remove unused platform devices for old ALSA code
ARM: OMAP: Fix ASoC by enabling writes to XCCR and RCCR McBSP registers
ARM: OMAP: Fix gpio.c compile on 15xx with CONFIG_DEBUGFS
ARM: OMAP: Fix compile for beagle
ARM: OMAP: Fix compile for palmte
ARM: OMAP: Fix compile for various McBSP
arch/arm/mach-omap1/board-h2.c | 38 ---------- arch/arm/mach-omap1/board-h3.c | 38 ---------- arch/arm/mach-omap1/board-innovator.c | 39 ---------- arch/arm/mach-omap1/board-nokia770.c | 7 ++ arch/arm/mach-omap1/board-osk.c | 43 +---------- arch/arm/mach-omap1/board-palmte.c | 29 -------- arch/arm/mach-omap1/board-palmtt.c | 41 ----------- arch/arm/mach-omap1/board-palmz71.c | 37 ---------- arch/arm/mach-omap1/board-sx1.c | 38 +--------- arch/arm/mach-omap1/board-voiceblue.c | 1 arch/arm/mach-omap1/mcbsp.c | 1 arch/arm/mach-omap2/board-apollon.c | 64 ++--------------- arch/arm/mach-omap2/board-ldp.c | 2 - arch/arm/mach-omap2/board-omap3beagle.c | 9 +- arch/arm/mach-omap2/mcbsp.c | 1 arch/arm/plat-omap/dma.c | 5 - arch/arm/plat-omap/gpio.c | 3 + arch/arm/plat-omap/include/mach/aic23.h | 116 ------------------------------- arch/arm/plat-omap/include/mach/gpio.h | 10 --- arch/arm/plat-omap/include/mach/mcbsp.h | 7 ++ arch/arm/plat-omap/mcbsp.c | 4 + drivers/mtd/onenand/omap2.c | 6 +- 22 files changed, 45 insertions(+), 494 deletions(-) delete mode 100644 arch/arm/plat-omap/include/mach/aic23.h
Signature · 1 line
Signature
Tony Lindgren
maintainerPATCH 1/10 ARM: OMAP: Fix compile for various McBSP
Include irqs.h or cpu.h directly as needed to fix
omap builds.
--- arch/arm/mach-omap1/mcbsp.c | 1 + arch/arm/mach-omap2/mcbsp.c | 1 + 2 files changed, 2 insertions(+), 0 deletions(-)
arch/arm/mach-omap1/mcbsp.c +1 -0
@@ -17,6 +17,7 @@#include <linux/io.h> #include <linux/platform_device.h> +#include <mach/irqs.h> #include <mach/dma.h> #include <mach/irqs.h> #include <mach/mux.h>
arch/arm/mach-omap2/mcbsp.c +1 -0
@@ -17,6 +17,7 @@#include <linux/io.h> #include <linux/platform_device.h> +#include <mach/irqs.h> #include <mach/dma.h> #include <mach/irqs.h> #include <mach/mux.h>
Tony Lindgren
maintainerPATCH 2/10 ARM: OMAP: Fix compile for palmte
In reply to Tony LindgrenRemove old MMC platform init code accidentally
left behind.
Patches are welcome to the new style MMC init code.
--- arch/arm/mach-omap1/board-palmte.c | 9 --------- 1 files changed, 0 insertions(+), 9 deletions(-)
arch/arm/mach-omap1/board-palmte.c +0 -9
@@ -195,15 +195,6 @@ static struct omap_usb_config palmte_usb_config __initdata = { .pins[0] = 2, }; -static struct omap_mmc_config palmte_mmc_config__initdata = { - .mmc[0 ] = { - .enabled =1 , - .wp_pin =PALMTE_MMC_WP_GPIO , - .power_pin =PALMTE_MMC_POWER_GPIO , - .switch_pin =PALMTE_MMC_SWITCH_GPIO , - }, -}; -static struct omap_lcd_config palmte_lcd_config__initdata = { .ctrl_name ="internal" , };
Tony Lindgren
maintainerPATCH 3/10 ARM: OMAP: Fix gpio by switching to generic gpio calls, v2
In reply to Tony LindgrenFrom: Jarkko Nikula <[email protected]>
Fix compile by removing remaining omap specific gpio calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch to do this with gpio_keys.
--- arch/arm/mach-omap1/board-sx1.c | 6 ++- arch/arm/mach-omap2/board-apollon.c | 64 +++----------------------------- arch/arm/mach-omap2/board-ldp.c | 2 + arch/arm/plat-omap/include/mach/gpio.h | 10 ----- drivers/mtd/onenand/omap2.c | 6 ++- 5 files changed, 13 insertions(+), 75 deletions(-)
arch/arm/mach-omap1/board-sx1.c +3 -3
@@ -423,9 +423,9 @@ static void __init omap_sx1_init(void)/* turn on USB power */ /* sx1_setusbpower(1); cant do it here because i2c is not ready */ -omap_request_gpio (1 );/* A_IRDA_OFF */ -omap_request_gpio (11 );/* A_SWITCH */ -omap_request_gpio (15 );/* A_USB_ON */ +gpio_request (1 ,"A_IRDA_OFF" ); +gpio_request (11 ,"A_SWITCH" ); +gpio_request (15 ,"A_USB_ON" );gpio_direction_output (1 ,1 );/*A_IRDA_OFF = 1 */ gpio_direction_output (11 ,0 );/*A_SWITCH = 0 */ gpio_direction_output (15 ,0 );/*A_USB_ON = 0 */
arch/arm/mach-omap2/board-apollon.c +6 -58
86 lines not on this page · raw message
arch/arm/mach-omap2/board-ldp.c +1 -1
@@ -88,7 +88,7 @@ static inline void __init ldp_init_smc911x(void) ldp_smc911x_resources[1 ].start =OMAP_GPIO_IRQ (eth_gpio); -if (omap_request_gpio (eth_gpio) <0 ) { +if (gpio_request (eth_gpio,"smc911x irq" ) <0 ) {printk (KERN_ERR "Failed to request GPIO%d for smc911x IRQ\n" , eth_gpio);return ;
arch/arm/plat-omap/include/mach/gpio.h +0 -10
@@ -87,16 +87,6 @@ extern void omap_set_gpio_debounce_time(int gpio, int enable);#include <linux/errno.h> #include <asm-generic/gpio.h> -static inline int omap_request_gpio (int gpio) -{ -return gpio_request (gpio,"FIXME" ); -} - -static inline void omap_free_gpio (int gpio) -{ -gpio_free (gpio); -} -static inline int gpio_get_value (unsigned gpio) {return __gpio_get_value (gpio);
drivers/mtd/onenand/omap2.c +3 -3
@@ -629,7 +629,7 @@ static int __devinit omap2_onenand_probe(struct platform_device *pdev) }if (c->gpio_irq) { -if ((r =omap_request_gpio (c->gpio_irq)) <0 ) { +if ((r =gpio_request (c->gpio_irq,"OneNAND irq" )) <0 ) {dev_err (&pdev->dev,"Failed to request GPIO%d for " "OneNAND\n" , c->gpio_irq); goto err_iounmap;
@@ -726,7 +726,7 @@ err_release_dma:free_irq (gpio_to_irq (c->gpio_irq), c); err_release_gpio:if (c->gpio_irq) -omap_free_gpio (c->gpio_irq); +gpio_free (c->gpio_irq); err_iounmap:iounmap (c->onenand.base); err_release_mem_region:
@@ -761,7 +761,7 @@ static int __devexit omap2_onenand_remove(struct platform_device *pdev)platform_set_drvdata (pdev,NULL );if (c->gpio_irq) {free_irq (gpio_to_irq (c->gpio_irq), c); -omap_free_gpio (c->gpio_irq); +gpio_free (c->gpio_irq); }iounmap (c->onenand.base);release_mem_region (c->phys_base,ONENAND_IO_SIZE );
Tony Lindgren
maintainerPATCH 4/10 ARM: OMAP: Fix compile for beagle
In reply to Tony LindgrenMove twl4030 gpio init code to where it should be. Also include twl4030.h.
--- arch/arm/mach-omap2/board-omap3beagle.c | 9 +++++---- 1 files changed, 5 insertions(+), 4 deletions(-)
arch/arm/mach-omap2/board-omap3beagle.c +5 -4
@@ -28,6 +28,8 @@#include <linux/mtd/partitions.h> #include <linux/mtd/nand.h> +#include <linux/i2c/twl4030.h> +#include <mach/hardware.h> #include <asm/mach-types.h> #include <asm/mach/arch.h>
@@ -120,6 +122,9 @@ static int beagle_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio) {/* gpio + 0 is "mmc0_cd" (input/IRQ) */ +omap_cfg_reg (AH8_34XX_GPIO29 ); + mmc[0 ].gpio_cd = gpio +0 ; +twl4030_mmc_init (mmc);/* REVISIT: need ehci-omap hooks for external VBUS * power switch and overcurrent detect
@@ -304,10 +309,6 @@ static void __init omap3_beagle_init(void) omap_board_config_size =ARRAY_SIZE (omap3_beagle_config);omap_serial_init (); -omap_cfg_reg (AH8_34XX_GPIO29 ); - mmc[0 ].gpio_cd = gpio +0 ; -twl4030_mmc_init (mmc); -omap_cfg_reg (J25_34XX_GPIO170 );gpio_request (170 ,"DVI_nPD" );/* REVISIT leave DVI powered down until it's needed ... */
Tony Lindgren
maintainerPATCH 5/10 ARM: OMAP: Fix gpio.c compile on 15xx with CONFIG_DEBUGFS
In reply to Tony LindgrenThere are no wakeup registers on 15xx, and suspend_wakeup does not exist in the struct gpio_bank.
Without this fix we'll get "arch/arm/plat-omap/gpio.c:1792:
error: 'struct gpio_bank' has no member named 'suspend_wakeup'" as noted by Russell King.
Note that the ifdefs will be cleaned up once the omap gpio code gets split into omap1 and omap2 specific parts.
--- arch/arm/plat-omap/gpio.c | 3 +++ 1 files changed, 3 insertions(+), 0 deletions(-)
arch/arm/plat-omap/gpio.c +3 -0
@@ -1789,6 +1789,8 @@ static int dbg_gpio_show(struct seq_file *s, void *unused)/* FIXME for at least omap2, show pullup/pulldown state */ irqstat = irq_desc[irq].status; +#if defined(CONFIG_ARCH_OMAP16XX ) || defined(CONFIG_ARCH_OMAP24XX ) || \ + defined(CONFIG_ARCH_OMAP34XX )if (is_in && ((bank->suspend_wakeup & mask) || irqstat &IRQ_TYPE_SENSE_MASK )) {char *trigger =NULL ;
@@ -1818,6 +1820,7 @@ static int dbg_gpio_show(struct seq_file *s, void *unused) (bank->suspend_wakeup & mask) ? " wakeup" : ""); } +#endif seq_printf (s,"\n" ); }
Tony Lindgren
maintainerPATCH 6/10 ARM: OMAP: Fix DMA CCR programming for request line > 63
In reply to Tony LindgrenFrom: Anand Gadiyar <[email protected]>
Bug in existing code causes synchro control to be set +32 if request line greater than 63 is used.
Reported by Wenbiao Wang
--- arch/arm/plat-omap/dma.c | 5 +---- 1 files changed, 1 insertions(+), 4 deletions(-)
arch/arm/plat-omap/dma.c +1 -4
@@ -279,10 +279,7 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, val =dma_read (CCR (lch)); val &= ~(3 <<19 ); -if (dma_trigger >63 ) - val |=1 <<20 ; -if (dma_trigger >31 ) - val |=1 <<19 ; + val |= ((dma_trigger & ~(0x1f )) <<14 ); val &= ~(0x1f ); val |= (dma_trigger &0x1f );
RE: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63
Quoted 36 lines
-----Original Message-----
From: Tony Lindgren [mailto:[email protected]]
Sent: Monday, January 12, 2009 8:15 PM
To: [email protected]
Cc: [email protected]; Gadiyar, Anand
Subject: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63From: Anand Gadiyar <[email protected]>
Bug in existing code causes synchro control to be set +32 if request line greater than 63 is used.
Reported by Wenbiao Wang
Signed-off-by Anand Gadiyar <[email protected]>Signed-off-by Tony Lindgren <[email protected]>--- arch/arm/plat-omap/dma.c | 5 +---- 1 files changed, 1 insertions(+), 4 deletions(-)arch/arm/plat-omap/dma.c +1
-4@@ -279,10 +279,7 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, val =dma_read (CCR (lch)); val &= ~(3 <<19 ); -if (dma_trigger >63 ) - val |=1 <<20 ; -if (dma_trigger >31 ) - val |=1 <<19 ; + val |= ((dma_trigger & ~(0x1f )) <<14 ); val &= ~(0x1f );
Quoted 4 lines
val |= (
dma_trigger&0x1f);
Reviewing my own patch. Is it better to use
val |= ((dma_trigger & 0x60) << 14) instead?
Or is this fine, as is?
Thanks,
Anand
Tony Lindgren
maintainerRe: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63
Quoted 42 lines · Gadiyar, Anand
Quoted 36 lines
-----Original Message-----
From: Tony Lindgren [mailto:[email protected]]
Sent: Monday, January 12, 2009 8:15 PM
To: [email protected]
Cc: [email protected]; Gadiyar, Anand
Subject: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63From: Anand Gadiyar <[email protected]>
Bug in existing code causes synchro control to be set +32 if request line greater than 63 is used.
Reported by Wenbiao Wang
Signed-off-by Anand Gadiyar <[email protected]>Signed-off-by Tony Lindgren <[email protected]>--- arch/arm/plat-omap/dma.c | 5 +---- 1 files changed, 1 insertions(+), 4 deletions(-)arch/arm/plat-omap/dma.c +1
-4@@ -279,10 +279,7 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, val =dma_read (CCR (lch)); val &= ~(3 <<19 ); -if (dma_trigger >63 ) - val |=1 <<20 ; -if (dma_trigger >31 ) - val |=1 <<19 ; + val |= ((dma_trigger & ~(0x1f )) <<14 ); val &= ~(0x1f );Quoted 4 lines
val |= (
dma_trigger&0x1f);Reviewing my own patch. Is it better to use
Quoted 3 lines
val |= ((dma_trigger & 0x60) << 14) instead?Or is this fine, as is?
Well at least you could remove some parens.
How about (dma_trigger / 32) << 19 instead?
Regards,
Tony
Re: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63
Quoted 2 lines · Tony Lindgren
Well at least you could remove some parens.
How about (dma_trigger/ 32) << 19 instead?
Be very careful. gcc 4.3.2 ignores the cost of calling its support functions, so it could well decide to _actually_ do that as a divide rather than the obvious bit clear. Not only that, but the guys at Simtec found that gcc 4.3.2 sometimes generates the optimal code followed by the library call, followed by code overwrite the result of the library call with the version from the optimal code!
This issue is the subject of an open gcc bug; and I believe is the reason that kautobuild's compiler doesn't have ARMv7 support at the moment.
Re: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63
In reply to Tony LindgrenQuoted 2 lines · Tony Lindgren
Well at least you could remove some parens.
How about (dma_trigger/ 32) << 19 instead?
Oh, and further to my previous reply there is also the general principle of writing what you mean. So, if you mean to clear the least significant 5 bits, write it as a mask with ~0x1f, not as a divide.
And no, you don't need ~(0x1f) - the parens there are pure noise. ~0x1f does just as well and isn't in any way confusing to the compiler. To put it another way, parens around a single value are completely meaningless.
Tony Lindgren
maintainerRe: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63, v2
Quoted 4 lines · Russell King - ARM Linux
Quoted 2 lines · Tony Lindgren
Well at least you could remove some parens.
How about (dma_trigger/ 32) << 19 instead?
Quoted 8 lines
Oh, and further to my previous reply there is also the general principle of writing what you mean. So, if you mean to clear the least significant 5 bits, write it as a mask with ~0x1f, not as a divide.
And no, you don't need ~(0x1f) - the parens there are pure noise. ~0x1f does just as well and isn't in any way confusing to the compiler. To put it another way, parens around a single value are completely meaningless.
Here's this one with the extra parens removed.
Tony
Quoted 1 line
From
cccdfb22248a88a68c0947cb6ff6b7faae852739Mon Sep 17 00:00:00 2001
From: Anand Gadiyar <[email protected]>
Date: Mon, 12 Jan 2009 16:01:03 +0200
Subject: [PATCH] ARM: OMAP: Fix DMA CCR programming for request line > 63, v2
Bug in existing code causes synchro control to be set +32 if request line greater than 63 is used.
Reported by Wenbiao Wang
arch/arm/plat-omap/dma.c +1 -4
@@ -279,10 +279,7 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, val =dma_read (CCR (lch)); val &= ~(3 <<19 ); -if (dma_trigger >63 ) - val |=1 <<20 ; -if (dma_trigger >31 ) - val |=1 <<19 ; + val |= ((dma_trigger & ~0x1f ) <<14 ); val &= ~(0x1f ); val |= (dma_trigger &0x1f );
Re: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63, v2
Quoted 9 lines · Tony Lindgren
Quoted 8 lines · Russell King - ARM Linux
Quoted 2 lines · Tony Lindgren
Well at least you could remove some parens.
How about (dma_trigger/ 32) << 19 instead?Oh, and further to my previous reply there is also the general principle of writing what you mean. So, if you mean to clear the least significant 5 bits, write it as a mask with ~0x1f, not as a divide.
Quoted 6 lines
Quoted 4 lines
And no, you don't need ~(0x1f) - the parens there are pure noise. ~0x1f does just as well and isn't in any way confusing to the compiler. To put it another way, parens around a single value are completely meaningless.
Here's this one with the extra parens removed.
If you're concerned about useless parens, then...
Quoted 6 lines
arch/arm/plat-omap/dma.c +0
-0@@ -279,10 +279,7 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count,
arch/arm/plat-omap/dma.c void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, · line 285
Quoted 10 lines
arch/arm/plat-omap/dma.c +1
-4val =dma_read (CCR (lch)); val &= ~(3 <<19 ); -if (dma_trigger >63 ) - val |=1 <<20 ; -if (dma_trigger >31 ) - val |=1 <<19 ; + val |= ((dma_trigger & ~0x1f ) <<14 ); val &= ~(0x1f ); val |= (dma_trigger &0x1f );
should change to:
val = dma_read(CCR(lch)); val &= ~(3 << 19); val |= (dma_trigger & ~0x1f) << 14; val &= ~0x1f; val |= dma_trigger & 0x1f;
Tony Lindgren
maintainerRe: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63, v2
Quoted 38 lines · Russell King - ARM Linux
Quoted 9 lines · Tony Lindgren
Quoted 8 lines · Russell King - ARM Linux
Quoted 2 lines · Tony Lindgren
Well at least you could remove some parens.
How about (dma_trigger/ 32) << 19 instead?Oh, and further to my previous reply there is also the general principle of writing what you mean. So, if you mean to clear the least significant 5 bits, write it as a mask with ~0x1f, not as a divide.
Quoted 6 lines
Quoted 4 lines
And no, you don't need ~(0x1f) - the parens there are pure noise. ~0x1f does just as well and isn't in any way confusing to the compiler. To put it another way, parens around a single value are completely meaningless.
Here's this one with the extra parens removed.
If you're concerned about useless parens, then...
Quoted 6 lines
arch/arm/plat-omap/dma.c +0
-0@@ -279,10 +279,7 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count,arch/arm/plat-omap/dma.c void omap_set_dma_transfer_params(int lch, int data_type, int elem_count, · line 285
Quoted 10 lines
arch/arm/plat-omap/dma.c +1
-4val =dma_read (CCR (lch)); val &= ~(3 <<19 ); -if (dma_trigger >63 ) - val |=1 <<20 ; -if (dma_trigger >31 ) - val |=1 <<19 ; + val |= ((dma_trigger & ~0x1f ) <<14 ); val &= ~(0x1f ); val |= (dma_trigger &0x1f );should change to:
Quoted 6 lines
val = dma_read(CCR(lch)); val &= ~(3 << 19); val |= (dma_trigger & ~0x1f) << 14; val &= ~0x1f; val |= dma_trigger & 0x1f;
How about this? Of course the bits should be defined for DMA_SYNCHRO_CONTROL_UPPER and DMA_SYNCHRO_CONTROL, but that may not count as a fix..
Tony
Quoted 1 line
From
80637cc6235ffcb8cd5ec4dd9a91cbd2b885d71bMon Sep 17 00:00:00 2001
From: Anand Gadiyar <[email protected]>
Date: Mon, 12 Jan 2009 16:01:03 +0200
Subject: [PATCH] ARM: OMAP: Fix DMA CCR programming for request line > 63, v3
Bug in existing code causes synchro control to be set +32 if request line greater than 63 is used.
Also clean up the function a bit by removing extra parens and clearing the bits at before write.
Reported by Wenbiao Wang.
arch/arm/plat-omap/dma.c +5 -8
@@ -278,14 +278,11 @@ void omap_set_dma_transfer_params(int lch, int data_type, int elem_count,u32 val; val =dma_read (CCR (lch)); - val &= ~(3 <<19 ); -if (dma_trigger >63 ) - val |=1 <<20 ; -if (dma_trigger >31 ) - val |=1 <<19 ; - - val &= ~(0x1f ); - val |= (dma_trigger &0x1f ); + +/* DMA_SYNCHRO_CONTROL_UPPER depends on the channel number */ + val &= ~((3 <<19 ) |0x1f ); + val |= (dma_trigger & ~0x1f ) <<14 ; + val |= dma_trigger &0x1f ;if (sync_mode &OMAP_DMA_SYNC_FRAME ) val |=1 <<5 ;
Re: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63, v2
Quoted 3 lines · Tony Lindgren
How about this? Of course the bits should be defined for
DMA_SYNCHRO_CONTROL_UPPERandDMA_SYNCHRO_CONTROL, but that may not count as a fix..
Ok.
Tony Lindgren
maintainerRe: [PATCH 06/10] ARM: OMAP: Fix DMA CCR programming for request line > 63, v2
Quoted 6 lines · Russell King - ARM Linux
Quoted 3 lines · Tony Lindgren
How about this? Of course the bits should be defined for
DMA_SYNCHRO_CONTROL_UPPERandDMA_SYNCHRO_CONTROL, but that may not count as a fix..Ok.
One more update to fix compile on omap1 as noted by Russell.
Tony
Quoted 1 line
From
3127f8f8595a064b3f1a1837fea2177902589ac3Mon Sep 17 00:00:00 2001
From: Tony Lindgren <Lopez>
Date: Thu, 15 Jan 2009 13:09:54 +0200
Subject: [PATCH] ARM: OMAP: Fix ASoC by enabling writes to XCCR and RCCR McBSP registers, v3
This patch enables writing to McBSP Transmit Configuration Control Register (XCCR) and Receive Configuration Control Register (RCCR) for 2430/34xx platforms. It also adds XCCR, RCCR entries in McBSP register configuration structure and bit definitions for both registers.
If we enable the writing to CCR registers for 2430/34xx and don't set the default values (setting 0 as a consequence) in ASoC driver, the Transmit/Receive DMA mode gets disabled and the the transmission/reception doesn't happen, ending with a "write error: Input/Output error" when playing with 'aplay'.
Also define dummy CCR registers for omap1.
arch/arm/plat-omap/include/mach/mcbsp.h +11 -0
@@ -87,6 +87,10 @@#define OMAP_MCBSP_REG_XCERG 0x3A#define OMAP_MCBSP_REG_XCERH 0x3C +/* Dummy defines, these are not available on omap1 */ +#define OMAP_MCBSP_REG_XCCR 0x00 +#define OMAP_MCBSP_REG_RCCR 0x00 +#define AUDIO_MCBSP_DATAWRITE (OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DXR1)#define AUDIO_MCBSP_DATAREAD (OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DRR1)
@@ -231,11 +235,16 @@#define XPBBLK (value) ((value)<<7)/* Bits 7:8 */ /*********************** McBSP XCCR bit definitions *************************/ +#define EXTCLKGATE 0x8000 +#define PPCONNECT 0x4000 +#define DXENDLY (value) ((value)<<12)/* Bits 12:13 */ +#define XFULL_CYCLE 0x0800#define DILB 0x0020#define XDMAEN 0x0008#define XDISABLE 0x0001/********************** McBSP RCCR bit definitions *************************/ +#define RFULL_CYCLE 0x0800#define RDMAEN 0x0008#define RDISABLE 0x0001
@@ -267,6 +276,8 @@ struct omap_mcbsp_reg_cfg {u16 rcerh;u16 xcerg;u16 xcerh; +u16 xccr; +u16 rccr; }; typedef enum {
arch/arm/plat-omap/mcbsp.c +4 -0
@@ -173,6 +173,10 @@ void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg *config)OMAP_MCBSP_WRITE (io_base,MCR2 , config->mcr2);OMAP_MCBSP_WRITE (io_base,MCR1 , config->mcr1);OMAP_MCBSP_WRITE (io_base,PCR0 , config->pcr0); +if (cpu_is_omap2430 () ||cpu_is_omap34xx ()) { +OMAP_MCBSP_WRITE (io_base,XCCR , config->xccr); +OMAP_MCBSP_WRITE (io_base,RCCR , config->rccr); + } }EXPORT_SYMBOL (omap_mcbsp_config);
Tony Lindgren
maintainerPATCH 7/10 ARM: OMAP: remove duplicated #include's
In reply to Tony LindgrenFrom: Huang Weiyi <[email protected]>
Removed duplicated #include's in arch/arm/mach-omap1/board-voiceblue.c
--- arch/arm/mach-omap1/board-voiceblue.c | 1 - 1 files changed, 0 insertions(+), 1 deletions(-)
arch/arm/mach-omap1/board-voiceblue.c +0 -1
@@ -22,7 +22,6 @@#include <linux/reboot.h> #include <linux/serial_8250.h> #include <linux/serial_reg.h> -#include <linux/irq.h> #include <mach/hardware.h> #include <asm/mach-types.h>
Tony Lindgren
maintainerPATCH 8/10 ARM: OMAP: Fix OSK ASoC by registering I2C board info for tlvaic23
In reply to Tony LindgrenFrom: Arun KS <[email protected]>
Adding I2C board info is required for tlvaic23 i2c chip driver.
--- arch/arm/mach-omap1/board-osk.c | 4 +++- 1 files changed, 3 insertions(+), 1 deletions(-)
arch/arm/mach-omap1/board-osk.c +3 -1
@@ -259,8 +259,10 @@ static struct i2c_board_info __initdata osk_i2c_board_info[] = { .platform_data = &tps_board, }, + { + I2C_BOARD_INFO("tlv320aic23", 0x1B), + },/* TODO when driver support is ready: -* - aic23 audio chip at 0x1a * - optionally on Mistral, ov9640 camera sensor at 0x30 */ };
Tony Lindgren
maintainerPATCH 9/10 ARM: OMAP: Fix ASoC by enabling writes to XCCR and RCCR McBSP registers
In reply to Tony LindgrenFrom: Tony Lindgren <Lopez>
This patch enables writing to McBSP Transmit Configuration Control Register (XCCR) and Receive Configuration Control Register (RCCR) for 2430/34xx platforms. It also adds XCCR, RCCR entries in McBSP register configuration structure and bit definitions for both registers.
If we enable the writing to CCR registers for 2430/34xx and don't set the default values (setting 0 as a consequence) in ASoC driver, the Transmit/Receive DMA mode gets disabled and the the transmission/reception doesn't happen, ending with a "write error: Input/Output error" when playing with 'aplay'.
--- arch/arm/plat-omap/include/mach/mcbsp.h | 7 +++++++ arch/arm/plat-omap/mcbsp.c | 4 ++++ 2 files changed, 11 insertions(+), 0 deletions(-)
arch/arm/plat-omap/include/mach/mcbsp.h +7 -0
@@ -231,11 +231,16 @@#define XPBBLK (value) ((value)<<7)/* Bits 7:8 */ /*********************** McBSP XCCR bit definitions *************************/ +#define EXTCLKGATE 0x8000 +#define PPCONNECT 0x4000 +#define DXENDLY (value) ((value)<<12)/* Bits 12:13 */ +#define XFULL_CYCLE 0x0800#define DILB 0x0020#define XDMAEN 0x0008#define XDISABLE 0x0001/********************** McBSP RCCR bit definitions *************************/ +#define RFULL_CYCLE 0x0800#define RDMAEN 0x0008#define RDISABLE 0x0001
@@ -267,6 +272,8 @@ struct omap_mcbsp_reg_cfg {u16 rcerh;u16 xcerg;u16 xcerh; +u16 xccr; +u16 rccr; }; typedef enum {
arch/arm/plat-omap/mcbsp.c +4 -0
@@ -173,6 +173,10 @@ void omap_mcbsp_config(unsigned int id, const struct omap_mcbsp_reg_cfg *config)OMAP_MCBSP_WRITE (io_base,MCR2 , config->mcr2);OMAP_MCBSP_WRITE (io_base,MCR1 , config->mcr1);OMAP_MCBSP_WRITE (io_base,PCR0 , config->pcr0); +if (cpu_is_omap2430 () ||cpu_is_omap34xx ()) { +OMAP_MCBSP_WRITE (io_base,XCCR , config->xccr); +OMAP_MCBSP_WRITE (io_base,RCCR , config->rccr); + } }EXPORT_SYMBOL (omap_mcbsp_config);
Tony Lindgren
maintainerPATCH 10/10 ARM: OMAP: Remove unused platform devices for old ALSA code
In reply to Tony LindgrenThis patch removes old platform devices. The should be now replaced with ASoC driver. For boards not yet using ASoC, please see sound/soc/omap/osk5912.c.
Add dummy aic23_power_up and aic23_power_down functions for 770 to keep things compiling.
This patch is based on an earlier patch by Arun KS.
--- arch/arm/mach-omap1/board-h2.c | 38 ---------- arch/arm/mach-omap1/board-h3.c | 38 ---------- arch/arm/mach-omap1/board-innovator.c | 39 ---------- arch/arm/mach-omap1/board-nokia770.c | 7 ++ arch/arm/mach-omap1/board-osk.c | 39 ---------- arch/arm/mach-omap1/board-palmte.c | 20 ----- arch/arm/mach-omap1/board-palmtt.c | 41 ----------- arch/arm/mach-omap1/board-palmz71.c | 37 ---------- arch/arm/mach-omap1/board-sx1.c | 32 --------- arch/arm/plat-omap/include/mach/aic23.h | 116 ------------------------------- 10 files changed, 7 insertions(+), 400 deletions(-) delete mode 100644 arch/arm/plat-omap/include/mach/aic23.h
arch/arm/mach-omap1/board-h2.c +0 -38
@@ -45,8 +45,6 @@#include <mach/usb.h> #include <mach/keypad.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> static int h2_keymap[] = {KEY (0 ,0 ,KEY_LEFT ),
@@ -292,41 +290,6 @@ static struct platform_device h2_lcd_device = { .id = -1, }; -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (1 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (1 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (15 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (31 ), - - .pcr0 =CLKXM |CLKRM |FSXP |FSRP |CLKXP |CLKRP , -/*.pcr0 = CLKXP | CLKRP,*/ /* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="H2 TSC2101" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* tsc2101_configure, */ - .codec_set_samplerate =NULL ,/* tsc2101_set_samplerate, */ - .codec_clock_setup =NULL ,/* tsc2101_clock_setup, */ - .codec_clock_on =NULL ,/* tsc2101_clock_on, */ - .codec_clock_off =NULL ,/* tsc2101_clock_off, */ - .get_default_samplerate =NULL ,/* tsc2101_get_default_samplerate, */ -}; - -static struct platform_device h2_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct platform_device *h2_devices[]__initdata = { &h2_nor_device, &h2_nand_device,
@@ -334,7 +297,6 @@ static struct platform_device *h2_devices[] __initdata = { &h2_irda_device, &h2_kp_device, &h2_lcd_device, - &h2_mcbsp1_device, };static void __init h2_init_smc91x (void )
arch/arm/mach-omap1/board-h3.c +0 -38
@@ -49,8 +49,6 @@#include <mach/keypad.h> #include <mach/dma.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> #define H3_TS_GPIO 48
@@ -387,41 +385,6 @@ static struct spi_board_info h3_spi_board_info[] __initdata = { }, }; -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (1 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (1 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (15 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (31 ), - - .pcr0 =CLKRM |SCLKME |FSXP |FSRP |CLKXP |CLKRP , -/*.pcr0 = CLKXP | CLKRP,*/ /* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="H3 TSC2101" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* tsc2101_configure, */ - .codec_set_samplerate =NULL ,/* tsc2101_set_samplerate, */ - .codec_clock_setup =NULL ,/* tsc2101_clock_setup, */ - .codec_clock_on =NULL ,/* tsc2101_clock_on, */ - .codec_clock_off =NULL ,/* tsc2101_clock_off, */ - .get_default_samplerate =NULL ,/* tsc2101_get_default_samplerate, */ -}; - -static struct platform_device h3_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct platform_device *devices[]__initdata = { &nor_device, &nand_device,
@@ -430,7 +393,6 @@ static struct platform_device *devices[] __initdata = { &h3_irda_device, &h3_kp_device, &h3_lcd_device, - &h3_mcbsp1_device, }; static struct omap_usb_config h3_usb_config __initdata = {
arch/arm/mach-omap1/board-innovator.c +0 -39
@@ -37,8 +37,6 @@#include <mach/usb.h> #include <mach/keypad.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> #include <mach/mmc.h> static int innovator_keymap[] = {
@@ -115,42 +113,6 @@ static struct platform_device innovator_flash_device = { .resource = &innovator_flash_resource, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (0 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (0 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (DEFAULT_BITPERSAMPLE -1 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (DEFAULT_BITPERSAMPLE *2 -1 ), -/*.pcr0 = FSXM | FSRM | CLKXM | CLKRM | CLKXP | CLKRP,*/ /* mcbsp: master */ - .pcr0 =CLKXP |CLKRP ,/* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="OMAP Innovator AIC23" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* aic23_configure, */ - .codec_set_samplerate =NULL ,/* aic23_set_samplerate, */ - .codec_clock_setup =NULL ,/* aic23_clock_setup, */ - .codec_clock_on =NULL ,/* aic23_clock_on, */ - .codec_clock_off =NULL ,/* aic23_clock_off, */ - .get_default_samplerate =NULL ,/* aic23_get_default_samplerate, */ -}; - -static struct platform_device innovator_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct resource innovator_kp_resources[] = { [0 ] = { .start =INT_KEYBOARD ,
@@ -227,7 +189,6 @@ static struct platform_device innovator1510_spi_device = {static struct platform_device *innovator1510_devices[]__initdata = { &innovator_flash_device, &innovator1510_smc91x_device, - &innovator_mcbsp1_device, &innovator_kp_device, &innovator1510_lcd_device, &innovator1510_spi_device,
arch/arm/mach-omap1/board-nokia770.c +7 -0
@@ -261,6 +261,13 @@ static DEFINE_MUTEX(audio_pwr_lock);*/ static int audio_pwr_state =-1 ; +static inline void aic23_power_up (void ) +{ +} +static inline void aic23_power_down (void ) +{ +} +/* * audio_pwr_up / down should be called under audio_pwr_lock */
arch/arm/mach-omap1/board-osk.c +0 -39
@@ -51,8 +51,6 @@#include <mach/mux.h> #include <mach/tc.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> static struct mtd_partition osk_partitions[] = {/* bootloader (U-Boot, etc) in first sector */
@@ -141,47 +139,10 @@ static struct platform_device osk5912_cf_device = { .resource = osk5912_cf_resources, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (0 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (0 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (DEFAULT_BITPERSAMPLE -1 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (DEFAULT_BITPERSAMPLE *2 -1 ), -/*.pcr0 = FSXM | FSRM | CLKXM | CLKRM | CLKXP | CLKRP,*/ /* mcbsp: master */ - .pcr0 =CLKXP |CLKRP ,/* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="OSK AIC23" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* aic23_configure, */ - .codec_set_samplerate =NULL ,/* aic23_set_samplerate, */ - .codec_clock_setup =NULL ,/* aic23_clock_setup, */ - .codec_clock_on =NULL ,/* aic23_clock_on, */ - .codec_clock_off =NULL ,/* aic23_clock_off, */ - .get_default_samplerate =NULL ,/* aic23_get_default_samplerate, */ -}; - -static struct platform_device osk5912_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct platform_device *osk5912_devices[]__initdata = { &osk5912_flash_device, &osk5912_smc91x_device, &osk5912_cf_device, - &osk5912_mcbsp1_device, };static struct gpio_led tps_leds[] = {
arch/arm/mach-omap1/board-palmte.c +0 -20
@@ -42,8 +42,6 @@#include <mach/irda.h> #include <mach/keypad.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> static void __init omap_palmte_init_irq (void ) {
@@ -203,24 +201,6 @@ static struct omap_uart_config palmte_uart_config __initdata = { .enabled_uarts = (1 << 0) | (1 << 1) | (0 << 2), }; -static struct omap_mcbsp_reg_cfg palmte_mcbsp1_regs = { - .spcr2 =FRST |GRST |XRST |XINTM (3 ), - .xcr2 =XDATDLY (1 ) |XFIG , - .xcr1 =XWDLEN1 (OMAP_MCBSP_WORD_32 ), - .pcr0 =SCLKME |FSXP |CLKXP , -}; - -static struct omap_alsa_codec_config palmte_alsa_config = { - .name ="TSC2102 audio" , - .mcbsp_regs_alsa = &palmte_mcbsp1_regs, - .codec_configure_dev =NULL ,/* tsc2102_configure, */ - .codec_set_samplerate =NULL ,/* tsc2102_set_samplerate, */ - .codec_clock_setup =NULL ,/* tsc2102_clock_setup, */ - .codec_clock_on =NULL ,/* tsc2102_clock_on, */ - .codec_clock_off =NULL ,/* tsc2102_clock_off, */ - .get_default_samplerate =NULL ,/* tsc2102_get_default_samplerate, */ -}; -#ifdef CONFIG_APM /* * Values measured in 10 minute intervals averaged over 10 samples.
arch/arm/mach-omap1/board-palmtt.c +0 -41
65 lines not on this page · raw message
arch/arm/mach-omap1/board-palmz71.c +0 -37
@@ -32,7 +32,6 @@#include <asm/mach/map.h> #include <asm/mach/flash.h> -#include <mach/mcbsp.h> #include <mach/gpio.h> #include <mach/mux.h> #include <mach/usb.h>
@@ -179,41 +178,6 @@ static struct platform_device palmz71_spi_device = { .id = -1, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (0 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (0 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (DEFAULT_BITPERSAMPLE -1 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (DEFAULT_BITPERSAMPLE *2 -1 ), - .pcr0 =CLKXP |CLKRP ,/* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="PalmZ71 AIC23" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* aic23_configure */ - .codec_set_samplerate =NULL ,/* aic23_set_samplerate */ - .codec_clock_setup =NULL ,/* aic23_clock_setup */ - .codec_clock_on =NULL ,/* aic23_clock_on */ - .codec_clock_off =NULL ,/* aic23_clock_off */ - .get_default_samplerate =NULL ,/* aic23_get_default_samplerate */ -}; - -static struct platform_device palmz71_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct omap_backlight_config palmz71_backlight_config = { .default_intensity =0xa0 , };
@@ -229,7 +193,6 @@ static struct platform_device palmz71_backlight_device = {static struct platform_device *devices[]__initdata = { &palmz71_rom_device, &palmz71_kp_device, - &palmz71_mcbsp1_device, &palmz71_lcd_device, &palmz71_irda_device, &palmz71_spi_device,
arch/arm/mach-omap1/board-sx1.c +0 -32
@@ -39,8 +39,6 @@#include <mach/tc.h> #include <mach/board.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> #include <mach/keypad.h> /* Write to I2C device */
@@ -254,35 +252,6 @@ static struct platform_device sx1_irda_device = { .resource = sx1_irda_resources, }; -/*----------- McBSP & Sound -------------------------*/ - -/* Playback interface - McBSP1 */ -static struct omap_mcbsp_reg_cfg mcbsp1_regs = { - .spcr2 =XINTM (3 ),/* SPCR2=30 */ - .spcr1 =RINTM (3 ),/* SPCR1=30 */ - .rcr2 =0 ,/* RCR2 =00 */ - .rcr1 =RFRLEN1 (1 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ),/* RCR1=140 */ - .xcr2 =0 ,/* XCR2 = 0 */ - .xcr1 =XFRLEN1 (1 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ),/* XCR1 = 140 */ - .srgr1 =FWID (15 ) |CLKGDV (12 ),/* SRGR1=0f0c */ - .srgr2 =FSGM |FPER (31 ),/* SRGR2=101f */ - .pcr0 =FSXM |FSRM |CLKXM |CLKRM |FSXP |FSRP |CLKXP |CLKRP , -/* PCR0 =0f0f */ -}; - -static struct omap_alsa_codec_config sx1_alsa_config = { - .name ="SX1 EGold" , - .mcbsp_regs_alsa = &mcbsp1_regs, -}; - -static struct platform_device sx1_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &sx1_alsa_config, - }, -}; -/*----------- MTD -------------------------*/ static struct mtd_partition sx1_partitions[] = {
@@ -394,7 +363,6 @@ static struct platform_device *sx1_devices[] __initdata = { &sx1_flash_device, &sx1_kp_device, &sx1_lcd_device, - &sx1_mcbsp1_device, &sx1_irda_device, };/*-----------------------------------------*/
arch/arm/plat-omap/include/mach/aic23.h deleted +0 -116
116 lines not on this page · raw message
Tony Lindgren
maintainerRe: [PATCH 10/10] ARM: OMAP: Remove unused platform devices for old ALSA code
Quoted 8 lines · Tony Lindgren
This patch removes old platform devices. The should be now replaced with ASoC driver. For boards not yet using ASoC, please see
sound/soc/omap/osk5912.c.Add dummy
aic23_power_upandaic23_power_downfunctions for 770 to keep things compiling.This patch is based on an earlier patch by Arun KS.
Updates to fix H2 compile as noted by Russell King. ALso remove unused gpio_switch and nand code.
Tony
Quoted 1 line
From
bf0b92849b730519130ddcf25c184e8401d30c13Mon Sep 17 00:00:00 2001
From: Tony Lindgren <[email protected]>
Date: Thu, 15 Jan 2009 13:55:59 +0200
Subject: [PATCH] ARM: OMAP: Remove unused platform devices, v2
This patch removes old platform devices. Alsa should now be using the ASoC driver. For boards not yet using ASoC, please see sound/soc/omap/osk5912.c.
Add dummy aic23_power_up and aic23_power_down functions for 770 to keep things compiling.
Remove references to omap_gpio_switch, and unused h2_nand_dev_ready function.
This patch is based on an earlier patch by Arun KS.
arch/arm/mach-omap1/board-h2.c +1 -44
@@ -37,16 +37,14 @@#include <asm/mach/flash.h> #include <asm/mach/map.h> -#include <mach/gpio-switch.h> #include <mach/mux.h> +#include <mach/dma.h> #include <mach/tc.h> #include <mach/nand.h> #include <mach/irda.h> #include <mach/usb.h> #include <mach/keypad.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> static int h2_keymap[] = {KEY (0 ,0 ,KEY_LEFT ),
@@ -292,41 +290,6 @@ static struct platform_device h2_lcd_device = { .id = -1, }; -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (1 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (1 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (15 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (31 ), - - .pcr0 =CLKXM |CLKRM |FSXP |FSRP |CLKXP |CLKRP , -/*.pcr0 = CLKXP | CLKRP,*/ /* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="H2 TSC2101" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* tsc2101_configure, */ - .codec_set_samplerate =NULL ,/* tsc2101_set_samplerate, */ - .codec_clock_setup =NULL ,/* tsc2101_clock_setup, */ - .codec_clock_on =NULL ,/* tsc2101_clock_on, */ - .codec_clock_off =NULL ,/* tsc2101_clock_off, */ - .get_default_samplerate =NULL ,/* tsc2101_get_default_samplerate, */ -}; - -static struct platform_device h2_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct platform_device *h2_devices[]__initdata = { &h2_nor_device, &h2_nand_device,
@@ -334,7 +297,6 @@ static struct platform_device *h2_devices[] __initdata = { &h2_irda_device, &h2_kp_device, &h2_lcd_device, - &h2_mcbsp1_device, };static void __init h2_init_smc91x (void )
@@ -409,11 +371,6 @@ static struct omap_board_config_kernel h2_config[] __initdata = {#define H2_NAND_RB_GPIO_PIN 62 -static int h2_nand_dev_ready (struct omap_nand_platform_data *data) -{ -return gpio_get_value (H2_NAND_RB_GPIO_PIN ); -} -static void __init h2_init (void ) {/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
arch/arm/mach-omap1/board-h3.c +0 -50
74 lines not on this page · raw message
arch/arm/mach-omap1/board-innovator.c +0 -39
@@ -37,8 +37,6 @@#include <mach/usb.h> #include <mach/keypad.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> #include <mach/mmc.h> static int innovator_keymap[] = {
@@ -115,42 +113,6 @@ static struct platform_device innovator_flash_device = { .resource = &innovator_flash_resource, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (0 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (0 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (DEFAULT_BITPERSAMPLE -1 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (DEFAULT_BITPERSAMPLE *2 -1 ), -/*.pcr0 = FSXM | FSRM | CLKXM | CLKRM | CLKXP | CLKRP,*/ /* mcbsp: master */ - .pcr0 =CLKXP |CLKRP ,/* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="OMAP Innovator AIC23" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* aic23_configure, */ - .codec_set_samplerate =NULL ,/* aic23_set_samplerate, */ - .codec_clock_setup =NULL ,/* aic23_clock_setup, */ - .codec_clock_on =NULL ,/* aic23_clock_on, */ - .codec_clock_off =NULL ,/* aic23_clock_off, */ - .get_default_samplerate =NULL ,/* aic23_get_default_samplerate, */ -}; - -static struct platform_device innovator_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct resource innovator_kp_resources[] = { [0 ] = { .start =INT_KEYBOARD ,
@@ -227,7 +189,6 @@ static struct platform_device innovator1510_spi_device = {static struct platform_device *innovator1510_devices[]__initdata = { &innovator_flash_device, &innovator1510_smc91x_device, - &innovator_mcbsp1_device, &innovator_kp_device, &innovator1510_lcd_device, &innovator1510_spi_device,
arch/arm/mach-omap1/board-nokia770.c +7 -0
@@ -261,6 +261,13 @@ static DEFINE_MUTEX(audio_pwr_lock);*/ static int audio_pwr_state =-1 ; +static inline void aic23_power_up (void ) +{ +} +static inline void aic23_power_down (void ) +{ +} +/* * audio_pwr_up / down should be called under audio_pwr_lock */
arch/arm/mach-omap1/board-osk.c +0 -39
@@ -51,8 +51,6 @@#include <mach/mux.h> #include <mach/tc.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> static struct mtd_partition osk_partitions[] = {/* bootloader (U-Boot, etc) in first sector */
@@ -141,47 +139,10 @@ static struct platform_device osk5912_cf_device = { .resource = osk5912_cf_resources, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (0 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (0 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (DEFAULT_BITPERSAMPLE -1 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (DEFAULT_BITPERSAMPLE *2 -1 ), -/*.pcr0 = FSXM | FSRM | CLKXM | CLKRM | CLKXP | CLKRP,*/ /* mcbsp: master */ - .pcr0 =CLKXP |CLKRP ,/* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="OSK AIC23" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* aic23_configure, */ - .codec_set_samplerate =NULL ,/* aic23_set_samplerate, */ - .codec_clock_setup =NULL ,/* aic23_clock_setup, */ - .codec_clock_on =NULL ,/* aic23_clock_on, */ - .codec_clock_off =NULL ,/* aic23_clock_off, */ - .get_default_samplerate =NULL ,/* aic23_get_default_samplerate, */ -}; - -static struct platform_device osk5912_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct platform_device *osk5912_devices[]__initdata = { &osk5912_flash_device, &osk5912_smc91x_device, &osk5912_cf_device, - &osk5912_mcbsp1_device, };static struct gpio_led tps_leds[] = {
arch/arm/mach-omap1/board-palmte.c +0 -20
@@ -42,8 +42,6 @@#include <mach/irda.h> #include <mach/keypad.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> static void __init omap_palmte_init_irq (void ) {
@@ -203,24 +201,6 @@ static struct omap_uart_config palmte_uart_config __initdata = { .enabled_uarts = (1 << 0) | (1 << 1) | (0 << 2), }; -static struct omap_mcbsp_reg_cfg palmte_mcbsp1_regs = { - .spcr2 =FRST |GRST |XRST |XINTM (3 ), - .xcr2 =XDATDLY (1 ) |XFIG , - .xcr1 =XWDLEN1 (OMAP_MCBSP_WORD_32 ), - .pcr0 =SCLKME |FSXP |CLKXP , -}; - -static struct omap_alsa_codec_config palmte_alsa_config = { - .name ="TSC2102 audio" , - .mcbsp_regs_alsa = &palmte_mcbsp1_regs, - .codec_configure_dev =NULL ,/* tsc2102_configure, */ - .codec_set_samplerate =NULL ,/* tsc2102_set_samplerate, */ - .codec_clock_setup =NULL ,/* tsc2102_clock_setup, */ - .codec_clock_on =NULL ,/* tsc2102_clock_on, */ - .codec_clock_off =NULL ,/* tsc2102_clock_off, */ - .get_default_samplerate =NULL ,/* tsc2102_get_default_samplerate, */ -}; -#ifdef CONFIG_APM /* * Values measured in 10 minute intervals averaged over 10 samples.
arch/arm/mach-omap1/board-palmtt.c +0 -41
65 lines not on this page · raw message
arch/arm/mach-omap1/board-palmz71.c +0 -37
@@ -32,7 +32,6 @@#include <asm/mach/map.h> #include <asm/mach/flash.h> -#include <mach/mcbsp.h> #include <mach/gpio.h> #include <mach/mux.h> #include <mach/usb.h>
@@ -179,41 +178,6 @@ static struct platform_device palmz71_spi_device = { .id = -1, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (0 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (0 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (DEFAULT_BITPERSAMPLE -1 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (DEFAULT_BITPERSAMPLE *2 -1 ), - .pcr0 =CLKXP |CLKRP ,/* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="PalmZ71 AIC23" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* aic23_configure */ - .codec_set_samplerate =NULL ,/* aic23_set_samplerate */ - .codec_clock_setup =NULL ,/* aic23_clock_setup */ - .codec_clock_on =NULL ,/* aic23_clock_on */ - .codec_clock_off =NULL ,/* aic23_clock_off */ - .get_default_samplerate =NULL ,/* aic23_get_default_samplerate */ -}; - -static struct platform_device palmz71_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct omap_backlight_config palmz71_backlight_config = { .default_intensity =0xa0 , };
@@ -229,7 +193,6 @@ static struct platform_device palmz71_backlight_device = {static struct platform_device *devices[]__initdata = { &palmz71_rom_device, &palmz71_kp_device, - &palmz71_mcbsp1_device, &palmz71_lcd_device, &palmz71_irda_device, &palmz71_spi_device,
arch/arm/mach-omap1/board-sx1.c +0 -32
@@ -39,8 +39,6 @@#include <mach/tc.h> #include <mach/board.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> #include <mach/keypad.h> /* Write to I2C device */
@@ -254,35 +252,6 @@ static struct platform_device sx1_irda_device = { .resource = sx1_irda_resources, }; -/*----------- McBSP & Sound -------------------------*/ - -/* Playback interface - McBSP1 */ -static struct omap_mcbsp_reg_cfg mcbsp1_regs = { - .spcr2 =XINTM (3 ),/* SPCR2=30 */ - .spcr1 =RINTM (3 ),/* SPCR1=30 */ - .rcr2 =0 ,/* RCR2 =00 */ - .rcr1 =RFRLEN1 (1 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ),/* RCR1=140 */ - .xcr2 =0 ,/* XCR2 = 0 */ - .xcr1 =XFRLEN1 (1 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ),/* XCR1 = 140 */ - .srgr1 =FWID (15 ) |CLKGDV (12 ),/* SRGR1=0f0c */ - .srgr2 =FSGM |FPER (31 ),/* SRGR2=101f */ - .pcr0 =FSXM |FSRM |CLKXM |CLKRM |FSXP |FSRP |CLKXP |CLKRP , -/* PCR0 =0f0f */ -}; - -static struct omap_alsa_codec_config sx1_alsa_config = { - .name ="SX1 EGold" , - .mcbsp_regs_alsa = &mcbsp1_regs, -}; - -static struct platform_device sx1_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &sx1_alsa_config, - }, -}; -/*----------- MTD -------------------------*/ static struct mtd_partition sx1_partitions[] = {
@@ -394,7 +363,6 @@ static struct platform_device *sx1_devices[] __initdata = { &sx1_flash_device, &sx1_kp_device, &sx1_lcd_device, - &sx1_mcbsp1_device, &sx1_irda_device, };/*-----------------------------------------*/
arch/arm/plat-omap/include/mach/aic23.h deleted +0 -116
116 lines not on this page · raw message
Tony Lindgren
maintainerRe: [PATCH 10/10] ARM: OMAP: Remove unused platform devices, v3
Quoted 5 lines · Tony Lindgren
Quoted 4 lines · Tony Lindgren
This patch removes old platform devices. The should be now replaced with ASoC driver. For boards not yet using ASoC, please see
sound/soc/omap/osk5912.c.
Quoted 7 lines
Quoted 4 lines
Add dummy
aic23_power_upandaic23_power_downfunctions for 770 to keep things compiling.This patch is based on an earlier patch by Arun KS.
Updates to fix H2 compile as noted by Russell King. ALso remove unused
gpio_switchand nand code.
One more update, now with include fixes for sx1 and 770.
Tony
Quoted 1 line
From
e999bbe7f1318390e997d13e508e4f16b1b130afMon Sep 17 00:00:00 2001
From: Tony Lindgren <[email protected]>
Date: Thu, 15 Jan 2009 13:55:59 +0200
Subject: [PATCH] ARM: OMAP: Remove unused platform devices, v3
This patch removes old platform devices. Alsa should now be using the ASoC driver. For boards not yet using ASoC, please see sound/soc/omap/osk5912.c.
Add dummy aic23_power_up and aic23_power_down functions for 770 to keep things compiling.
Remove references to omap_gpio_switch, and unused h2_nand_dev_ready function.
This patch is based on an earlier patch by Arun KS.
arch/arm/mach-omap1/board-h2.c +1 -44
@@ -37,16 +37,14 @@#include <asm/mach/flash.h> #include <asm/mach/map.h> -#include <mach/gpio-switch.h> #include <mach/mux.h> +#include <mach/dma.h> #include <mach/tc.h> #include <mach/nand.h> #include <mach/irda.h> #include <mach/usb.h> #include <mach/keypad.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> static int h2_keymap[] = {KEY (0 ,0 ,KEY_LEFT ),
@@ -292,41 +290,6 @@ static struct platform_device h2_lcd_device = { .id = -1, }; -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (1 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (1 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (15 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (31 ), - - .pcr0 =CLKXM |CLKRM |FSXP |FSRP |CLKXP |CLKRP , -/*.pcr0 = CLKXP | CLKRP,*/ /* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="H2 TSC2101" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* tsc2101_configure, */ - .codec_set_samplerate =NULL ,/* tsc2101_set_samplerate, */ - .codec_clock_setup =NULL ,/* tsc2101_clock_setup, */ - .codec_clock_on =NULL ,/* tsc2101_clock_on, */ - .codec_clock_off =NULL ,/* tsc2101_clock_off, */ - .get_default_samplerate =NULL ,/* tsc2101_get_default_samplerate, */ -}; - -static struct platform_device h2_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct platform_device *h2_devices[]__initdata = { &h2_nor_device, &h2_nand_device,
@@ -334,7 +297,6 @@ static struct platform_device *h2_devices[] __initdata = { &h2_irda_device, &h2_kp_device, &h2_lcd_device, - &h2_mcbsp1_device, };static void __init h2_init_smc91x (void )
@@ -409,11 +371,6 @@ static struct omap_board_config_kernel h2_config[] __initdata = {#define H2_NAND_RB_GPIO_PIN 62 -static int h2_nand_dev_ready (struct omap_nand_platform_data *data) -{ -return gpio_get_value (H2_NAND_RB_GPIO_PIN ); -} -static void __init h2_init (void ) {/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
arch/arm/mach-omap1/board-h3.c +0 -50
74 lines not on this page · raw message
arch/arm/mach-omap1/board-innovator.c +0 -39
@@ -37,8 +37,6 @@#include <mach/usb.h> #include <mach/keypad.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> #include <mach/mmc.h> static int innovator_keymap[] = {
@@ -115,42 +113,6 @@ static struct platform_device innovator_flash_device = { .resource = &innovator_flash_resource, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (0 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (0 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (DEFAULT_BITPERSAMPLE -1 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (DEFAULT_BITPERSAMPLE *2 -1 ), -/*.pcr0 = FSXM | FSRM | CLKXM | CLKRM | CLKXP | CLKRP,*/ /* mcbsp: master */ - .pcr0 =CLKXP |CLKRP ,/* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="OMAP Innovator AIC23" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* aic23_configure, */ - .codec_set_samplerate =NULL ,/* aic23_set_samplerate, */ - .codec_clock_setup =NULL ,/* aic23_clock_setup, */ - .codec_clock_on =NULL ,/* aic23_clock_on, */ - .codec_clock_off =NULL ,/* aic23_clock_off, */ - .get_default_samplerate =NULL ,/* aic23_get_default_samplerate, */ -}; - -static struct platform_device innovator_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct resource innovator_kp_resources[] = { [0 ] = { .start =INT_KEYBOARD ,
@@ -227,7 +189,6 @@ static struct platform_device innovator1510_spi_device = {static struct platform_device *innovator1510_devices[]__initdata = { &innovator_flash_device, &innovator1510_smc91x_device, - &innovator_mcbsp1_device, &innovator_kp_device, &innovator1510_lcd_device, &innovator1510_spi_device,
arch/arm/mach-omap1/board-nokia770.c +7 -1
@@ -32,7 +32,6 @@#include <mach/keypad.h> #include <mach/common.h> #include <mach/dsp_common.h> -#include <mach/aic23.h> #include <mach/omapfb.h> #include <mach/lcd_mipid.h> #include <mach/mmc.h>
@@ -261,6 +260,13 @@ static DEFINE_MUTEX(audio_pwr_lock);*/ static int audio_pwr_state =-1 ; +static inline void aic23_power_up (void ) +{ +} +static inline void aic23_power_down (void ) +{ +} +/* * audio_pwr_up / down should be called under audio_pwr_lock */
arch/arm/mach-omap1/board-osk.c +0 -39
@@ -51,8 +51,6 @@#include <mach/mux.h> #include <mach/tc.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> static struct mtd_partition osk_partitions[] = {/* bootloader (U-Boot, etc) in first sector */
@@ -141,47 +139,10 @@ static struct platform_device osk5912_cf_device = { .resource = osk5912_cf_resources, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (0 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (0 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (DEFAULT_BITPERSAMPLE -1 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (DEFAULT_BITPERSAMPLE *2 -1 ), -/*.pcr0 = FSXM | FSRM | CLKXM | CLKRM | CLKXP | CLKRP,*/ /* mcbsp: master */ - .pcr0 =CLKXP |CLKRP ,/* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="OSK AIC23" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* aic23_configure, */ - .codec_set_samplerate =NULL ,/* aic23_set_samplerate, */ - .codec_clock_setup =NULL ,/* aic23_clock_setup, */ - .codec_clock_on =NULL ,/* aic23_clock_on, */ - .codec_clock_off =NULL ,/* aic23_clock_off, */ - .get_default_samplerate =NULL ,/* aic23_get_default_samplerate, */ -}; - -static struct platform_device osk5912_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct platform_device *osk5912_devices[]__initdata = { &osk5912_flash_device, &osk5912_smc91x_device, &osk5912_cf_device, - &osk5912_mcbsp1_device, };static struct gpio_led tps_leds[] = {
arch/arm/mach-omap1/board-palmte.c +0 -20
@@ -42,8 +42,6 @@#include <mach/irda.h> #include <mach/keypad.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> static void __init omap_palmte_init_irq (void ) {
@@ -203,24 +201,6 @@ static struct omap_uart_config palmte_uart_config __initdata = { .enabled_uarts = (1 << 0) | (1 << 1) | (0 << 2), }; -static struct omap_mcbsp_reg_cfg palmte_mcbsp1_regs = { - .spcr2 =FRST |GRST |XRST |XINTM (3 ), - .xcr2 =XDATDLY (1 ) |XFIG , - .xcr1 =XWDLEN1 (OMAP_MCBSP_WORD_32 ), - .pcr0 =SCLKME |FSXP |CLKXP , -}; - -static struct omap_alsa_codec_config palmte_alsa_config = { - .name ="TSC2102 audio" , - .mcbsp_regs_alsa = &palmte_mcbsp1_regs, - .codec_configure_dev =NULL ,/* tsc2102_configure, */ - .codec_set_samplerate =NULL ,/* tsc2102_set_samplerate, */ - .codec_clock_setup =NULL ,/* tsc2102_clock_setup, */ - .codec_clock_on =NULL ,/* tsc2102_clock_on, */ - .codec_clock_off =NULL ,/* tsc2102_clock_off, */ - .get_default_samplerate =NULL ,/* tsc2102_get_default_samplerate, */ -}; -#ifdef CONFIG_APM /* * Values measured in 10 minute intervals averaged over 10 samples.
arch/arm/mach-omap1/board-palmtt.c +0 -41
65 lines not on this page · raw message
arch/arm/mach-omap1/board-palmz71.c +0 -37
@@ -32,7 +32,6 @@#include <asm/mach/map.h> #include <asm/mach/flash.h> -#include <mach/mcbsp.h> #include <mach/gpio.h> #include <mach/mux.h> #include <mach/usb.h>
@@ -179,41 +178,6 @@ static struct platform_device palmz71_spi_device = { .id = -1, }; -#define DEFAULT_BITPERSAMPLE 16 - -static struct omap_mcbsp_reg_cfg mcbsp_regs = { - .spcr2 =FREE |FRST |GRST |XRST |XINTM (3 ), - .spcr1 =RINTM (3 ) |RRST , - .rcr2 =RPHASE |RFRLEN2 (OMAP_MCBSP_WORD_8 ) | -RWDLEN2 (OMAP_MCBSP_WORD_16 ) |RDATDLY (0 ), - .rcr1 =RFRLEN1 (OMAP_MCBSP_WORD_8 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ), - .xcr2 =XPHASE |XFRLEN2 (OMAP_MCBSP_WORD_8 ) | -XWDLEN2 (OMAP_MCBSP_WORD_16 ) |XDATDLY (0 ) |XFIG , - .xcr1 =XFRLEN1 (OMAP_MCBSP_WORD_8 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ), - .srgr1 =FWID (DEFAULT_BITPERSAMPLE -1 ), - .srgr2 =GSYNC |CLKSP |FSGM |FPER (DEFAULT_BITPERSAMPLE *2 -1 ), - .pcr0 =CLKXP |CLKRP ,/* mcbsp: slave */ -}; - -static struct omap_alsa_codec_config alsa_config = { - .name ="PalmZ71 AIC23" , - .mcbsp_regs_alsa = &mcbsp_regs, - .codec_configure_dev =NULL ,/* aic23_configure */ - .codec_set_samplerate =NULL ,/* aic23_set_samplerate */ - .codec_clock_setup =NULL ,/* aic23_clock_setup */ - .codec_clock_on =NULL ,/* aic23_clock_on */ - .codec_clock_off =NULL ,/* aic23_clock_off */ - .get_default_samplerate =NULL ,/* aic23_get_default_samplerate */ -}; - -static struct platform_device palmz71_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &alsa_config, - }, -}; -static struct omap_backlight_config palmz71_backlight_config = { .default_intensity =0xa0 , };
@@ -229,7 +193,6 @@ static struct platform_device palmz71_backlight_device = {static struct platform_device *devices[]__initdata = { &palmz71_rom_device, &palmz71_kp_device, - &palmz71_mcbsp1_device, &palmz71_lcd_device, &palmz71_irda_device, &palmz71_spi_device,
arch/arm/mach-omap1/board-sx1.c +1 -32
@@ -34,13 +34,12 @@#include <mach/gpio.h> #include <mach/mux.h> +#include <mach/dma.h> #include <mach/irda.h> #include <mach/usb.h> #include <mach/tc.h> #include <mach/board.h> #include <mach/common.h> -#include <mach/mcbsp.h> -#include <mach/omap-alsa.h> #include <mach/keypad.h> /* Write to I2C device */
@@ -254,35 +253,6 @@ static struct platform_device sx1_irda_device = { .resource = sx1_irda_resources, }; -/*----------- McBSP & Sound -------------------------*/ - -/* Playback interface - McBSP1 */ -static struct omap_mcbsp_reg_cfg mcbsp1_regs = { - .spcr2 =XINTM (3 ),/* SPCR2=30 */ - .spcr1 =RINTM (3 ),/* SPCR1=30 */ - .rcr2 =0 ,/* RCR2 =00 */ - .rcr1 =RFRLEN1 (1 ) |RWDLEN1 (OMAP_MCBSP_WORD_16 ),/* RCR1=140 */ - .xcr2 =0 ,/* XCR2 = 0 */ - .xcr1 =XFRLEN1 (1 ) |XWDLEN1 (OMAP_MCBSP_WORD_16 ),/* XCR1 = 140 */ - .srgr1 =FWID (15 ) |CLKGDV (12 ),/* SRGR1=0f0c */ - .srgr2 =FSGM |FPER (31 ),/* SRGR2=101f */ - .pcr0 =FSXM |FSRM |CLKXM |CLKRM |FSXP |FSRP |CLKXP |CLKRP , -/* PCR0 =0f0f */ -}; - -static struct omap_alsa_codec_config sx1_alsa_config = { - .name ="SX1 EGold" , - .mcbsp_regs_alsa = &mcbsp1_regs, -}; - -static struct platform_device sx1_mcbsp1_device = { - .name ="omap_alsa_mcbsp" , - .id =1 , - .dev = { - .platform_data = &sx1_alsa_config, - }, -}; -/*----------- MTD -------------------------*/ static struct mtd_partition sx1_partitions[] = {
@@ -394,7 +364,6 @@ static struct platform_device *sx1_devices[] __initdata = { &sx1_flash_device, &sx1_kp_device, &sx1_lcd_device, - &sx1_mcbsp1_device, &sx1_irda_device, };/*-----------------------------------------*/
arch/arm/plat-omap/include/mach/aic23.h deleted +0 -116
116 lines not on this page · raw message
Tony Lindgren
maintainer[PATCH 11/10] ARM: OMAP: Fix compile for h3 MMC
In reply to Tony LindgrenFix compile for h3 MMC
arch/arm/plat-omap/include/mach/board-h3.h +3 -1
@@ -30,7 +30,9 @@/* In OMAP1710 H3 the Ethernet is directly connected to CS1 */ #define OMAP1710_ETHR_START 0x04000300 +#define H3_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */) +# define H3_TPS_GPIO_MMC_PWR_EN (H3_TPS_GPIO_BASE + 4) +extern void h3_mmc_init (void ); -extern void h3_mmc_slot_cover_handler (void *arg,int state);#endif /* __ASM_ARCH_OMAP_H3_H */
Tony Lindgren
maintainergit-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
In reply to Tony LindgrenQuoted 4 lines · Tony Lindgren
Hi,
Here are some omap fixes for review. Some of these patches were posted earlier.
If no other comments, here's the pull request:
The following changes since commit c59765042f53a79a7a65585042ff463b69cb248c:
Linus Torvalds (1):
Linux 2.6.29-rc1
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git omap-fixes
Anand Gadiyar (1):
ARM: OMAP: Fix DMA CCR programming for request line > 63, v3
Arun KS (1):
ARM: OMAP: Fix OSK ASoC by registering I2C board info for tlvaic23
Huang Weiyi (1):
ARM: OMAP: remove duplicated #include's
Jarkko Nikula (1):
ARM: OMAP: Fix gpio by switching to generic gpio calls, v2
Tony Lindgren (6):
ARM: OMAP: Fix compile for various McBSP
ARM: OMAP: Fix compile for palmte
ARM: OMAP: Fix compile for beagle
ARM: OMAP: Fix gpio.c compile on 15xx with CONFIG_DEBUGFS
ARM: OMAP: Fix ASoC by enabling writes to XCCR and RCCR McBSP registers
ARM: OMAP: Remove unused platform devices for old ALSA code
arch/arm/mach-omap1/board-h2.c | 38 ---------- arch/arm/mach-omap1/board-h3.c | 38 ---------- arch/arm/mach-omap1/board-innovator.c | 39 ---------- arch/arm/mach-omap1/board-nokia770.c | 7 ++ arch/arm/mach-omap1/board-osk.c | 43 +----------- arch/arm/mach-omap1/board-palmte.c | 29 -------- arch/arm/mach-omap1/board-palmtt.c | 41 ----------- arch/arm/mach-omap1/board-palmz71.c | 37 ---------- arch/arm/mach-omap1/board-sx1.c | 38 +--------- arch/arm/mach-omap1/board-voiceblue.c | 1 - arch/arm/mach-omap1/mcbsp.c | 1 + arch/arm/mach-omap2/board-apollon.c | 64 ++--------------- arch/arm/mach-omap2/board-ldp.c | 2 +- arch/arm/mach-omap2/board-omap3beagle.c | 9 ++- arch/arm/mach-omap2/mcbsp.c | 1 + arch/arm/plat-omap/dma.c | 13 ++-- arch/arm/plat-omap/gpio.c | 3 + arch/arm/plat-omap/include/mach/aic23.h | 116 ------------------------------- arch/arm/plat-omap/include/mach/gpio.h | 10 --- arch/arm/plat-omap/include/mach/mcbsp.h | 7 ++ arch/arm/plat-omap/mcbsp.c | 4 + drivers/mtd/onenand/omap2.c | 6 +- 22 files changed, 49 insertions(+), 498 deletions(-) delete mode 100644 arch/arm/plat-omap/include/mach/aic23.h
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 7 lines · Tony Lindgren
Quoted 4 lines · Tony Lindgren
Hi,
Here are some omap fixes for review. Some of these patches were posted earlier.
If no other comments, here's the pull request:
Unfortunately, this breaks stuff. Whereas before pulling this I get:
CC drivers/usb/core/hub.odrivers/usb/core/hub.c: In function `usb_configure_device_otg':drivers/usb/core/hub.c:1557: error: too few arguments to function `usb_port_suspend'
while building my omap config, I now get this much earlier in the build:
CC arch/arm/mach-omap1/board-h2.oarch/arm/mach-omap1/board-h2.c:259: error: `OMAP_DMA_UART3_RX' undeclared here (not in a function) arch/arm/mach-omap1/board-h2.c:259: error: initializer element is not constant arch/arm/mach-omap1/board-h2.c:259: error: (near initialization for h2_irda_data.rx_channel') arch/arm/mach-omap1/board-h2.c:260: error: OMAP_DMA_UART3_TX' undeclared here (not in a function) arch/arm/mach-omap1/board-h2.c:260: error: initializer element is not constant arch/arm/mach-omap1/board-h2.c:260: error: (near initialization for `h2_irda_data.tx_channel') arch/arm/mach-omap1/board-h2.c:375: warning: 'h2_nand_dev_ready' defined but not used
This has appeared because in 9f94ad8ab33417f98b363491d4730a67f4d92831, the include of mach/omap-alsa.h was removed, which includes mach/dma.h, and mach/dma.h is needed for these definitions.
It would be far better to omit mach/dma.h from mach/omap-alsa.h since mach/dma.h isn't strictly required for mach/omap-alsa.h (the file seems to contain nothing that requires anything from mach/dma.h) and then these kinds of accidents can be avoided.
With that fixed, that then brings us on to:
CC arch/arm/plat-omap/mcbsp.oarch/arm/plat-omap/mcbsp.c: In function `omap_mcbsp_config':arch/arm/plat-omap/mcbsp.c:177: error: `OMAP_MCBSP_REG_XCCR' undeclared (first use in this function) arch/arm/plat-omap/mcbsp.c:177: error: (Each undeclared identifier is reported only once arch/arm/plat-omap/mcbsp.c:177: error: for each function it appears in.) arch/arm/plat-omap/mcbsp.c:178: error: `OMAP_MCBSP_REG_RCCR' undeclared (first use in this function)
which is caused by 82b30192282d9b3da37d98af4b308d989ed6b92e.
Not pulling.
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 7 lines · Russell King - ARM Linux
Unfortunately, this breaks stuff. Whereas before pulling this I get:
CC drivers/usb/core/hub.o
drivers/usb/core/hub.c: In function `usb_configure_device_otg':drivers/usb/core/hub.c:1557: error: too few arguments to function `usb_port_suspend'while building my omap config, I now get this much earlier in the build:
ISTR seeing that before. I'm not sure what happened to Alan's patch ... I guess it didn't get merged yet.
- Dave
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Tony Lindgren
maintainerRe: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
In reply to Russell King - ARM LinuxQuoted 44 lines · Russell King - ARM Linux
Quoted 7 lines · Tony Lindgren
Quoted 4 lines · Tony Lindgren
Hi,
Here are some omap fixes for review. Some of these patches were posted earlier.
If no other comments, here's the pull request:
Unfortunately, this breaks stuff. Whereas before pulling this I get:
CC
drivers/usb/core/hub.odrivers/usb/core/hub.c: In function `usb_configure_device_otg':drivers/usb/core/hub.c:1557: error: too few arguments to function `usb_port_suspend'while building my omap config, I now get this much earlier in the build:
CC
arch/arm/mach-omap1/board-h2.oarch/arm/mach-omap1/board-h2.c:259: error: `OMAP_DMA_UART3_RX' undeclared here (not in a function)arch/arm/mach-omap1/board-h2.c:259: error: initializer element is not constantarch/arm/mach-omap1/board-h2.c:259: error: (near initialization forh2_irda_data.rx_channel') arch/arm/mach-omap1/board-h2.c:260: error:OMAP_DMA_UART3_TX' undeclared here (not in a function)arch/arm/mach-omap1/board-h2.c:260: error: initializer element is not constantarch/arm/mach-omap1/board-h2.c:260: error: (near initialization for `h2_irda_data.tx_channel')arch/arm/mach-omap1/board-h2.c:375: warning: 'h2_nand_dev_ready' defined but not usedThis has appeared because in
9f94ad8ab33417f98b363491d4730a67f4d92831, the include ofmach/omap-alsa.hwas removed, which includesmach/dma.h, andmach/dma.his needed for these definitions.It would be far better to omit
mach/dma.hfrommach/omap-alsa.hsincemach/dma.hisn't strictly required formach/omap-alsa.h(the file seems to contain nothing that requires anything frommach/dma.h) and then these kinds of accidents can be avoided.With that fixed, that then brings us on to:
CC
arch/arm/plat-omap/mcbsp.oarch/arm/plat-omap/mcbsp.c: In function `omap_mcbsp_config':arch/arm/plat-omap/mcbsp.c:177: error: `OMAP_MCBSP_REG_XCCR' undeclared (first use in this function)arch/arm/plat-omap/mcbsp.c:177: error: (Each undeclared identifier is reported only oncearch/arm/plat-omap/mcbsp.c:177: error: for each function it appears in.)arch/arm/plat-omap/mcbsp.c:178: error: `OMAP_MCBSP_REG_RCCR' undeclared (first use in this function)
Quoted 3 lines
which is caused by
82b30192282d9b3da37d98af4b308d989ed6b92e.Not pulling.
Hmm, I thought I build all the defconfigs before posting the series. Will update in just few mins.
Tony
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 10 lines · Tony Lindgren
Quoted 9 lines · Russell King - ARM Linux
Quoted 7 lines · Tony Lindgren
Quoted 4 lines · Tony Lindgren
Hi,
Here are some omap fixes for review. Some of these patches were posted earlier.
If no other comments, here's the pull request:
Quoted 8 lines
Quoted 5 lines
Unfortunately, this breaks stuff. Whereas before pulling this I get:
CC
drivers/usb/core/hub.odrivers/usb/core/hub.c: In function `usb_configure_device_otg':drivers/usb/core/hub.c:1557: error: too few arguments to function `usb_port_suspend'Hmm, I thought I build all the defconfigs before posting the series. Will update in just few mins.
Thanks. It would also be nice if the USB error could be fixed by USB folk as well - it's been broken since 2.6.28-git12. (Maybe people should check kautobuild's errors summary page?)
http://armlinux.simtec.co.uk/kautobuild/<version>/errors.html
where <version> should be replaced by, eg, 2.6.29-rc1-git4
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 3 lines · ext Russell King - ARM Linux
Thanks. It would also be nice if the USB error could be fixed by USB folk as well - it's been broken since 2.6.28-git12. (Maybe people should check kautobuild's errors summary page?)
are you talking about
drivers/usb/core/hub.c:1557: error: too few arguments to function 'usb_port_suspend' ??
that should be fixed by Greg, no ??
Signature · 1 line
balbi
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 9 lines · Felipe Balbi
Quoted 3 lines · ext Russell King - ARM Linux
Thanks. It would also be nice if the USB error could be fixed by USB folk as well - it's been broken since 2.6.28-git12. (Maybe people should check kautobuild's errors summary page?)
are you talking about
drivers/usb/core/hub.c:1557: error: too few arguments to function 'usb_port_suspend' ??
That was indeed the one quoted in my message.
Quoted 1 line
that should be fixed by Greg, no ??
Not sure - looks to be related to OTG... and seems to be caused by Alan Stern's 65bfd2967c906ca322a4bb69a285fe0de8916ac6 change "USB: Enhance usage of pm_message_t". Adding To's.
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 11 lines · Russell King - ARM Linux
Quoted 9 lines · Felipe Balbi
Quoted 3 lines · ext Russell King - ARM Linux
Thanks. It would also be nice if the USB error could be fixed by USB folk as well - it's been broken since 2.6.28-git12. (Maybe people should check kautobuild's errors summary page?)
are you talking about
drivers/usb/core/hub.c:1557: error: too few arguments to function 'usb_port_suspend' ??
Quoted 7 lines
That was indeed the one quoted in my message.
Quoted 1 line
that should be fixed by Greg, no ??
Not sure - looks to be related to OTG... and seems to be caused by Alan Stern's
65bfd2967c906ca322a4bb69a285fe0de8916ac6change "USB: Enhance usage ofpm_message_t". Adding To's.
Apparently the patch to fix this is still in Greg's queue. If you want to test the patch for yourself, it's here:
http://marc.info/?l=linux-usb&m=123032171110450&w=2
Alan Stern
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 17 lines · Alan Stern
Quoted 15 lines · Russell King - ARM Linux
Quoted 9 lines · Felipe Balbi
Quoted 3 lines · ext Russell King - ARM Linux
Thanks. It would also be nice if the USB error could be fixed by USB folk as well - it's been broken since 2.6.28-git12. (Maybe people should check kautobuild's errors summary page?)
are you talking about
drivers/usb/core/hub.c:1557: error: too few arguments to function 'usb_port_suspend' ??That was indeed the one quoted in my message.
Quoted 1 line
that should be fixed by Greg, no ??
Quoted 8 lines
Quoted 3 lines
Not sure - looks to be related to OTG... and seems to be caused by Alan Stern's
65bfd2967c906ca322a4bb69a285fe0de8916ac6change "USB: Enhance usage ofpm_message_t". Adding To's.Apparently the patch to fix this is still in Greg's queue. If you want to test the patch for yourself, it's here:
http://marc.info/?l=linux-usb&m=123032171110450&w=2
Sigh. Trivial build error. Trivial fix. Almost three weeks to get it into mainline and still waiting... Frustrated and annoyed.
(Isn't this the kind of slow bug fixing that akpm complains about at kernel summits?)
Tony Lindgren
maintainerRe: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
In reply to Russell King - ARM LinuxQuoted 20 lines · Russell King - ARM Linux
Quoted 10 lines · Tony Lindgren
Quoted 9 lines · Russell King - ARM Linux
Quoted 7 lines · Tony Lindgren
Quoted 4 lines · Tony Lindgren
Hi,
Here are some omap fixes for review. Some of these patches were posted earlier.
If no other comments, here's the pull request:
Quoted 8 lines
Quoted 5 lines
Unfortunately, this breaks stuff. Whereas before pulling this I get:
CC
drivers/usb/core/hub.odrivers/usb/core/hub.c: In function `usb_configure_device_otg':drivers/usb/core/hub.c:1557: error: too few arguments to function `usb_port_suspend'Hmm, I thought I build all the defconfigs before posting the series. Will update in just few mins.
Quoted 7 lines
Thanks. It would also be nice if the USB error could be fixed by USB folk as well - it's been broken since 2.6.28-git12. (Maybe people should check kautobuild's errors summary page?)
http://armlinux.simtec.co.uk/kautobuild/<version>/errors.html
where <version> should be replaced by, eg, 2.6.29-rc1-git4
Regarding the USB hub.c issue, sounds like Dave and Felipe are already looking into it.
I think I missed the other build errors because I probably forgot to manually try to rebuild the boards that failed on the usb.c error..
Here's the updated pull request for the other omap fixes.
Tony
The following changes since commit 5393f780277165f282a37ed82dd878159ec9dad5:
Linus Torvalds (1):
Merge branch 'merge' of git://git.kernel.org/.../benh/powerpc
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git omap-fixes
Anand Gadiyar (1):
ARM: OMAP: Fix DMA CCR programming for request line > 63, v3
Arun KS (1):
ARM: OMAP: Fix OSK ASoC by registering I2C board info for tlvaic23
Huang Weiyi (1):
ARM: OMAP: remove duplicated #include's
Jarkko Nikula (1):
ARM: OMAP: Fix gpio by switching to generic gpio calls, v2
Tony Lindgren (7):
ARM: OMAP: Fix compile for various McBSP
ARM: OMAP: Fix compile for palmte
ARM: OMAP: Fix compile for beagle
ARM: OMAP: Fix gpio.c compile on 15xx with CONFIG_DEBUGFS
ARM: OMAP: Fix ASoC by enabling writes to XCCR and RCCR McBSP registers, v3
ARM: OMAP: Remove unused platform devices, v3
ARM: OMAP: Fix compile for h3 MMC
arch/arm/mach-omap1/board-h2.c | 45 +----------- arch/arm/mach-omap1/board-h3.c | 50 ------------ arch/arm/mach-omap1/board-innovator.c | 39 --------- arch/arm/mach-omap1/board-nokia770.c | 8 ++- arch/arm/mach-omap1/board-osk.c | 43 +---------- arch/arm/mach-omap1/board-palmte.c | 29 ------- arch/arm/mach-omap1/board-palmtt.c | 41 ---------- arch/arm/mach-omap1/board-palmz71.c | 37 --------- arch/arm/mach-omap1/board-sx1.c | 39 +-------- arch/arm/mach-omap1/board-voiceblue.c | 1 - arch/arm/mach-omap1/mcbsp.c | 1 + arch/arm/mach-omap2/board-apollon.c | 64 ++-------------- arch/arm/mach-omap2/board-ldp.c | 2 +- arch/arm/mach-omap2/board-omap3beagle.c | 9 +- arch/arm/mach-omap2/mcbsp.c | 1 + arch/arm/plat-omap/dma.c | 13 +-- arch/arm/plat-omap/gpio.c | 3 + arch/arm/plat-omap/include/mach/aic23.h | 116 ---------------------------- arch/arm/plat-omap/include/mach/board-h3.h | 4 +- arch/arm/plat-omap/include/mach/gpio.h | 10 --- arch/arm/plat-omap/include/mach/mcbsp.h | 11 +++ arch/arm/plat-omap/mcbsp.c | 4 + drivers/mtd/onenand/omap2.c | 6 +- 23 files changed, 58 insertions(+), 518 deletions(-) delete mode 100644 arch/arm/plat-omap/include/mach/aic23.h
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 1 line · Tony Lindgren
Here's the updated pull request for the other omap fixes.
Thanks, this one's better.
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 4 lines · Russell King - ARM Linux
Quoted 1 line · Tony Lindgren
Here's the updated pull request for the other omap fixes.
Thanks, this one's better.
Now that akpm pushed the usb_port_suspend() fix upstream, we move on to the next breakage found by kautobuild, which for n770_defconfig is:
drivers/built-in.o: In function `ohci_omap_init':
hid-quirks.c:(.text+0x6c608): undefined reference to otg_get_transceiver' drivers/built-in.o: In function omap_udc_probe':
hid-quirks.c:(.init.text+0x34c0): undefined reference to otg_get_transceiver' hid-quirks.c:(.init.text+0x3d40): undefined reference to otg_put_transceiver'
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 8 lines · Russell King - ARM Linux
Now that akpm pushed the
usb_port_suspend()fix upstream, we move on to the next breakage found by kautobuild, which forn770_defconfigis:
drivers/built-in.o: In function `ohci_omap_init':
hid-quirks.c:(.text+0x6c608): undefined reference tootg_get_transceiver' drivers/built-in.o: In functionomap_udc_probe':
hid-quirks.c:(.init.text+0x34c0): undefined reference tootg_get_transceiver' hid-quirks.c:(.init.text+0x3d40): undefined reference tootg_put_transceiver'
Does this fix that problem?
--- drivers/usb/host/Kconfig | 1 + drivers/usb/otg/Kconfig | 4 ++-- 2 files changed, 3 insertions(+), 2 deletions(-)
drivers/usb/host/Kconfig +1 -0
@@ -140,6 +140,7 @@ config USB_OHCI_HCD tristate "OHCI HCD support" depends on USB && USB_ARCH_HAS_OHCI select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 + select USB_OTG_UTILS if ARCH_OMAP ---help--- The Open Host Controller Interface (OHCI) is a standard for accessing USB 1.1 host controller hardware. It does more in hardware than Intel's
drivers/usb/otg/Kconfig +2 -2
@@ -6,14 +6,14 @@ comment "OTG and related infrastructure" -if USB || USB_GADGET - config USB_OTG_UTILS bool help Select this to make sure the build includes objects from the OTG infrastructure directory. +if USB || USB_GADGET + # # USB Transceiver Drivers #
Tony Lindgren
maintainerRe: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 11 lines · David Brownell
Quoted 8 lines · Russell King - ARM Linux
Now that akpm pushed the
usb_port_suspend()fix upstream, we move on to the next breakage found by kautobuild, which forn770_defconfigis:
drivers/built-in.o: In function `ohci_omap_init':
hid-quirks.c:(.text+0x6c608): undefined reference tootg_get_transceiver' drivers/built-in.o: In functionomap_udc_probe':
hid-quirks.c:(.init.text+0x34c0): undefined reference tootg_get_transceiver' hid-quirks.c:(.init.text+0x3d40): undefined reference tootg_put_transceiver'Does this fix that problem?
Yes, that fixes it, Acked-by: Tony Lindgren <[email protected]>. I assume it will get merged via the USB tree, so not adding it to omap-fixes.
FYI, I'll be flying back home soon so I probably won't be online until Tuesday at some point in case there are other fixes needed.
Tony
Quoted 35 lines
--- drivers/usb/host/Kconfig | 1 + drivers/usb/otg/Kconfig | 4 ++-- 2 files changed, 3 insertions(+), 2 deletions(-)drivers/usb/host/Kconfig +1
-0@@ -140,6 +140,7 @@ config USB_OHCI_HCD tristate "OHCI HCD support" depends on USB && USB_ARCH_HAS_OHCI select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 + select USB_OTG_UTILS if ARCH_OMAP ---help--- The Open Host Controller Interface (OHCI) is a standard for accessing USB 1.1 host controller hardware. It does more in hardware than Intel'sdrivers/usb/otg/Kconfig +2
-2@@ -6,14 +6,14 @@ comment "OTG and related infrastructure" -if USB || USB_GADGET - config USB_OTG_UTILS bool help Select this to make sure the build includes objects from the OTG infrastructure directory. +if USB || USB_GADGET + # # USB Transceiver Drivers #
Re: git-pull request for omap-fixes for 2.6.29-rc1 (Re: [PATCH 00/10] Omap fixes for 2.6.29-rc1)
Quoted 2 lines · Tony Lindgren
FYI, I'll be flying back home soon so I probably won't be online until Tuesday at some point in case there are other fixes needed.
That doesn't really matter at the moment - Linus is at LCA and from what I hear, isn't planning to do very much in the way of patch merging this week.