Skip to contentSkip to conversation

ixgbe: fix dca issue with relaxed ordering turned on

PATCH Applied Jeff Kirsher 2 participants 6 messages Jan 20, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 ixgbe: fix dca issue with relaxed ordering turned on

From: Don Skidmore <[email protected]>

The is an issue where setting Relaxed Ordering (RO) bit (in a PCI-E write transaction) on 82598 causing the chipset to drop DCA hints. This patch forces RO not to be set for descriptors as well as payload. This will only be in effect while DCA is enabled and no performance difference was noticed in testing.

---

 drivers/net/ixgbe/ixgbe_main.c |    3 +++
 drivers/net/ixgbe/ixgbe_type.h |    3 +++
 2 files changed, 6 insertions(+), 0 deletions(-)
drivers/net/ixgbe/ixgbe_main.c +3 -0
index acef3c6..92d9b17 100644
@@ -318,6 +318,9 @@ static void ixgbe_update_rx_dca(struct ixgbe_adapter *adapter,
 		rxctrl |= dca3_get_tag(&adapter->pdev->dev, cpu);
 		rxctrl |= IXGBE_DCA_RXCTRL_DESC_DCA_EN;
 		rxctrl |= IXGBE_DCA_RXCTRL_HEAD_DCA_EN;
+		rxctrl &= ~(IXGBE_DCA_RXCTRL_DESC_RRO_EN);
+		rxctrl &= ~(IXGBE_DCA_RXCTRL_DESC_WRO_EN |
+			    IXGBE_DCA_RXCTRL_DESC_HSRO_EN);
 		IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_RXCTRL(q), rxctrl);
 		rx_ring->cpu = cpu;
 	}
drivers/net/ixgbe/ixgbe_type.h +3 -0
index 83a11ff..f011c57 100644
@@ -404,6 +404,9 @@
 #define IXGBE_DCA_RXCTRL_DESC_DCA_EN (1 << 5) /* DCA Rx Desc enable */
 #define IXGBE_DCA_RXCTRL_HEAD_DCA_EN (1 << 6) /* DCA Rx Desc header enable */
 #define IXGBE_DCA_RXCTRL_DATA_DCA_EN (1 << 7) /* DCA Rx Desc payload enable */
+#define IXGBE_DCA_RXCTRL_DESC_RRO_EN (1 << 9) /* DCA Rx rd Desc Relax Order */
+#define IXGBE_DCA_RXCTRL_DESC_WRO_EN (1 << 13) /* DCA Rx wr Desc Relax Order */
+#define IXGBE_DCA_RXCTRL_DESC_HSRO_EN (1 << 15) /* DCA Rx Split Header RO */
 
 #define IXGBE_DCA_TXCTRL_CPUID_MASK 0x0000001F /* Tx CPUID Mask */
 #define IXGBE_DCA_TXCTRL_DESC_DCA_EN (1 << 5) /* DCA Tx Desc enable */
#1 lore raw

PATCH 2/3 ixgbe: fix tag stripping for VLAN ID 0

From: Don Skidmore <[email protected]>

Register VLAN ID 0 so that frames with VLAN ID 0 are received and get their tag stripped when ixgbe is not in DCB mode. VLAN ID 0 means that the frame is 'priority tagged' only - it is not a VLAN, but the priority value is the tag in valid. The functions ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a couple functions to correct compiling issues with this change.

---

 drivers/net/ixgbe/ixgbe_main.c |   53 ++++++++++++++++++++--------------------
 1 files changed, 27 insertions(+), 26 deletions(-)
drivers/net/ixgbe/ixgbe_main.c +27 -26
index 92d9b17..bf36737 100644
@@ -1744,6 +1744,32 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 	IXGBE_WRITE_REG(hw, IXGBE_RXCSUM, rxcsum);
 }
 
+static void ixgbe_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
+{
+	struct ixgbe_adapter *adapter = netdev_priv(netdev);
+	struct ixgbe_hw *hw = &adapter->hw;
+
+	/* add VID to filter table */
+	hw->mac.ops.set_vfta(&adapter->hw, vid, 0, true);
+}
+
+static void ixgbe_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
+{
+	struct ixgbe_adapter *adapter = netdev_priv(netdev);
+	struct ixgbe_hw *hw = &adapter->hw;
+
+	if (!test_bit(__IXGBE_DOWN, &adapter->state))
+		ixgbe_irq_disable(adapter);
+
+	vlan_group_set_device(adapter->vlgrp, vid, NULL);
+
+	if (!test_bit(__IXGBE_DOWN, &adapter->state))
+		ixgbe_irq_enable(adapter);
+
+	/* remove VID from filter table */
+	hw->mac.ops.set_vfta(&adapter->hw, vid, 0, false);
+}
+
 static void ixgbe_vlan_rx_register(struct net_device *netdev,
                                    struct vlan_group *grp)
 {
@@ -1763,6 +1789,7 @@ static void ixgbe_vlan_rx_register(struct net_device *netdev,
 	ctrl |= IXGBE_VLNCTRL_VME;
 	ctrl &= ~IXGBE_VLNCTRL_CFIEN;
 	IXGBE_WRITE_REG(&adapter->hw, IXGBE_VLNCTRL, ctrl);
+	ixgbe_vlan_rx_add_vid(netdev, 0);
 
 	if (grp) {
 		/* enable VLAN tag insert/strip */
@@ -1776,32 +1803,6 @@ static void ixgbe_vlan_rx_register(struct net_device *netdev,
 		ixgbe_irq_enable(adapter);
 }
 
-static void ixgbe_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
-{
-	struct ixgbe_adapter *adapter = netdev_priv(netdev);
-	struct ixgbe_hw *hw = &adapter->hw;
-
-	/* add VID to filter table */
-	hw->mac.ops.set_vfta(&adapter->hw, vid, 0, true);
-}
-
-static void ixgbe_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
-{
-	struct ixgbe_adapter *adapter = netdev_priv(netdev);
-	struct ixgbe_hw *hw = &adapter->hw;
-
-	if (!test_bit(__IXGBE_DOWN, &adapter->state))
-		ixgbe_irq_disable(adapter);
-
-	vlan_group_set_device(adapter->vlgrp, vid, NULL);
-
-	if (!test_bit(__IXGBE_DOWN, &adapter->state))
-		ixgbe_irq_enable(adapter);
-
-	/* remove VID from filter table */
-	hw->mac.ops.set_vfta(&adapter->hw, vid, 0, false);
-}
-
 static void ixgbe_restore_vlan(struct ixgbe_adapter *adapter)
 {
 	ixgbe_vlan_rx_register(adapter->netdev, adapter->vlgrp);
maintainer Applied
#2 lore raw

Re: [PATCH 2/3] ixgbe: fix tag stripping for VLAN ID 0

From: Jeff Kirsher <[email protected]>
Date: Mon, 19 Jan 2009 16:11:26 -0800

Quoted 6 lines

Register VLAN ID 0 so that frames with VLAN ID 0 are received and get their tag stripped when ixgbe is not in DCB mode. VLAN ID 0 means that the frame is 'priority tagged' only - it is not a VLAN, but the priority value is the tag in valid. The functions ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a couple functions to correct compiling issues with this change.

Applied.

#3 lore raw

PATCH 3/3 ixgbe: Fix usage of netif_*_all_queues() with netif_carrier_{off|on}()

In reply to Jeff Kirsher

From: PJ Waskiewicz <[email protected]>

netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx queues is redundant and unnecessary. By the same token, netif_carrier_on() will be sufficient to re-enable Tx, so waking the queues is unnecessary.

---

 drivers/net/ixgbe/ixgbe_main.c |    6 +++---
 1 files changed, 3 insertions(+), 3 deletions(-)
drivers/net/ixgbe/ixgbe_main.c +3 -3
index bf36737..d2f4d5f 100644
@@ -2078,6 +2078,9 @@ static int ixgbe_up_complete(struct ixgbe_adapter *adapter)
 
 	ixgbe_irq_enable(adapter);
 
+	/* enable transmits */
+	netif_tx_start_all_queues(netdev);
+
 	/* bring the link up in the watchdog, this could race with our first
 	 * link up interrupt but shouldn't be a problem */
 	adapter->flags |= IXGBE_FLAG_NEED_LINK_UPDATE;
@@ -3479,7 +3482,6 @@ static void ixgbe_watchdog_task(struct work_struct *work)
 			        (FLOW_TX ? "TX" : "None"))));
 
 			netif_carrier_on(netdev);
-			netif_tx_wake_all_queues(netdev);
 		} else {
 			/* Force detection of hung controller */
 			adapter->detect_tx_hung = true;
@@ -3491,7 +3493,6 @@ static void ixgbe_watchdog_task(struct work_struct *work)
 			printk(KERN_INFO "ixgbe: %s NIC Link is Down\n",
 			       netdev->name);
 			netif_carrier_off(netdev);
-			netif_tx_stop_all_queues(netdev);
 		}
 	}
 
@@ -4222,7 +4223,6 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
 	}
 
 	netif_carrier_off(netdev);
-	netif_tx_stop_all_queues(netdev);
 
 	strcpy(netdev->name, "eth%d");
 	err = register_netdev(netdev);
maintainer Applied
#4 lore raw

Re: [PATCH 3/3] ixgbe: Fix usage of netif_*_all_queues() with netif_carrier_{off|on}()

From: Jeff Kirsher <[email protected]>
Date: Mon, 19 Jan 2009 16:11:47 -0800

Quoted 6 lines

netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx queues is redundant and unnecessary. By the same token, netif_carrier_on() will be sufficient to re-enable Tx, so waking the queues is unnecessary.

Applied.

maintainer Applied
#5 lore raw
In reply to Jeff Kirsher

From: Jeff Kirsher <[email protected]>
Date: Mon, 19 Jan 2009 16:11:05 -0800

Quoted 10 lines

The is an issue where setting Relaxed Ordering (RO) bit (in a PCI-E write transaction) on 82598 causing the chipset to drop DCA hints. This patch forces RO not to be set for descriptors as well as payload. This will only be in effect while DCA is enabled and no performance difference was noticed in testing.

Applied.