Skip to contentSkip to conversation

igb: Fix DCA errors and do not use context index for 82576

PATCH Applied Jeff Kirsher 2 participants 6 messages Jan 31, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 igb: Fix DCA errors and do not use context index for 82576

From: Alexander Duyck <[email protected]>

82576 was being incorrectly flagged as needing a context index. It does not as each ring has it's own table of 2 contexts.

Driver was registering after registering the driver instead of the other way around.

---

 drivers/net/igb/igb.h      |    9 ++++-----
 drivers/net/igb/igb_main.c |   16 ++++++----------
 2 files changed, 10 insertions(+), 15 deletions(-)
drivers/net/igb/igb.h +4 -5
index 5a27825..aebef8e 100644
@@ -300,11 +300,10 @@ struct igb_adapter {
 
 #define IGB_FLAG_HAS_MSI           (1 << 0)
 #define IGB_FLAG_MSI_ENABLE        (1 << 1)
-#define IGB_FLAG_HAS_DCA           (1 << 2)
-#define IGB_FLAG_DCA_ENABLED       (1 << 3)
-#define IGB_FLAG_IN_NETPOLL        (1 << 5)
-#define IGB_FLAG_QUAD_PORT_A       (1 << 6)
-#define IGB_FLAG_NEED_CTX_IDX      (1 << 7)
+#define IGB_FLAG_DCA_ENABLED       (1 << 2)
+#define IGB_FLAG_IN_NETPOLL        (1 << 3)
+#define IGB_FLAG_QUAD_PORT_A       (1 << 4)
+#define IGB_FLAG_NEED_CTX_IDX      (1 << 5)
 
 enum e1000_state_t {
 	__IGB_TESTING,
drivers/net/igb/igb_main.c +6 -10
index b82b0fb..cc94412 100644
@@ -206,10 +206,11 @@ static int __init igb_init_module(void)
 
 	global_quad_port_a = 0;
 
-	ret = pci_register_driver(&igb_driver);
 #ifdef CONFIG_IGB_DCA
 	dca_register_notify(&dca_notifier);
 #endif
+
+	ret = pci_register_driver(&igb_driver);
 	return ret;
 }
 
@@ -1156,11 +1157,10 @@ static int __devinit igb_probe(struct pci_dev *pdev,
 
 	/* set flags */
 	switch (hw->mac.type) {
-	case e1000_82576:
 	case e1000_82575:
-		adapter->flags |= IGB_FLAG_HAS_DCA;
 		adapter->flags |= IGB_FLAG_NEED_CTX_IDX;
 		break;
+	case e1000_82576:
 	default:
 		break;
 	}
@@ -1310,8 +1310,7 @@ static int __devinit igb_probe(struct pci_dev *pdev,
 		goto err_register;
 
 #ifdef CONFIG_IGB_DCA
-	if ((adapter->flags & IGB_FLAG_HAS_DCA) &&
-	    (dca_add_requester(&pdev->dev) == 0)) {
+	if (dca_add_requester(&pdev->dev) == 0) {
 		adapter->flags |= IGB_FLAG_DCA_ENABLED;
 		dev_info(&pdev->dev, "DCA enabled\n");
 		/* Always use CB2 mode, difference is masked
@@ -3473,19 +3472,16 @@ static int __igb_notify_dca(struct device *dev, void *data)
 	struct e1000_hw *hw = &adapter->hw;
 	unsigned long event = *(unsigned long *)data;
 
-	if (!(adapter->flags & IGB_FLAG_HAS_DCA))
-		goto out;
-
 	switch (event) {
 	case DCA_PROVIDER_ADD:
 		/* if already enabled, don't do it again */
 		if (adapter->flags & IGB_FLAG_DCA_ENABLED)
 			break;
-		adapter->flags |= IGB_FLAG_DCA_ENABLED;
 		/* Always use CB2 mode, difference is masked
 		 * in the CB driver. */
 		wr32(E1000_DCA_CTRL, 2);
 		if (dca_add_requester(dev) == 0) {
+			adapter->flags |= IGB_FLAG_DCA_ENABLED;
 			dev_info(&adapter->pdev->dev, "DCA enabled\n");
 			igb_setup_dca(adapter);
 			break;
@@ -3502,7 +3498,7 @@ static int __igb_notify_dca(struct device *dev, void *data)
 		}
 		break;
 	}
-out:
+
 	return 0;
 }
 
#1 lore raw

PATCH 2/3 igb: prevent skb_over panic w/ mtu smaller than 1K

From: Alexander Duyck <[email protected]>

A panic has been observed with frame sizes smaller than 1K. This has been root caused to the hardware spanning larger frames across multiple buffers and then reporting the original frame size in the first descriptor. To prevent this we can enable set the LPE bit which in turn will restrict packet sizes to those set in the RLPML register.

---

 drivers/net/igb/igb_main.c |    8 ++++----
 1 files changed, 4 insertions(+), 4 deletions(-)
drivers/net/igb/igb_main.c +4 -4
index cc94412..a50db53 100644
@@ -1834,11 +1834,11 @@ static void igb_setup_rctl(struct igb_adapter *adapter)
 	rctl |= E1000_RCTL_SECRC;
 
 	/*
-	 * disable store bad packets, long packet enable, and clear size bits.
+	 * disable store bad packets and clear size bits.
 	 */
-	rctl &= ~(E1000_RCTL_SBP | E1000_RCTL_LPE | E1000_RCTL_SZ_256);
+	rctl &= ~(E1000_RCTL_SBP | E1000_RCTL_SZ_256);
 
-	if (adapter->netdev->mtu > ETH_DATA_LEN)
+	/* enable LPE when to prevent packets larger than max_frame_size */
 		rctl |= E1000_RCTL_LPE;
 
 	/* Setup buffer sizes */
@@ -1864,7 +1864,7 @@ static void igb_setup_rctl(struct igb_adapter *adapter)
 	 */
 	/* allocations using alloc_page take too long for regular MTU
 	 * so only enable packet split for jumbo frames */
-	if (rctl & E1000_RCTL_LPE) {
+	if (adapter->netdev->mtu > ETH_DATA_LEN) {
 		adapter->rx_ps_hdr_size = IGB_RXBUFFER_128;
 		srrctl |= adapter->rx_ps_hdr_size <<
 			 E1000_SRRCTL_BSIZEHDRSIZE_SHIFT;
maintainer Applied
#2 lore raw

Re: [net-2.6 PATCH 2/3] igb: prevent skb_over panic w/ mtu smaller than 1K

From: Jeff Kirsher <[email protected]>
Date: Fri, 30 Jan 2009 16:54:04 -0800

Quoted 8 lines

A panic has been observed with frame sizes smaller than 1K. This has been root caused to the hardware spanning larger frames across multiple buffers and then reporting the original frame size in the first descriptor. To prevent this we can enable set the LPE bit which in turn will restrict packet sizes to those set in the RLPML register.

Applied.

#3 lore raw

PATCH 3/3 igb: fix link reporting when using sgmii

In reply to Jeff Kirsher

From: Alexander Duyck <[email protected]>

When using sgmii the link was not being properly passed up to the driver from the underlying link management functions. This change corrects it so that get_link_status is cleared when a link has been found.

---

 drivers/net/igb/e1000_82575.c |   11 +++++++++--
 1 files changed, 9 insertions(+), 2 deletions(-)
drivers/net/igb/e1000_82575.c +9 -2
index f5e2e72..13ca73f 100644
@@ -699,11 +699,18 @@ static s32 igb_check_for_link_82575(struct e1000_hw *hw)
 
 	/* SGMII link check is done through the PCS register. */
 	if ((hw->phy.media_type != e1000_media_type_copper) ||
-	    (igb_sgmii_active_82575(hw)))
+	    (igb_sgmii_active_82575(hw))) {
 		ret_val = igb_get_pcs_speed_and_duplex_82575(hw, &speed,
 		                                             &duplex);
-	else
+		/*
+		 * Use this flag to determine if link needs to be checked or
+		 * not.  If  we have link clear the flag so that we do not
+		 * continue to check for link.
+		 */
+		hw->mac.get_link_status = !hw->mac.serdes_has_link;
+	} else {
 		ret_val = igb_check_for_copper_link(hw);
+	}
 
 	return ret_val;
 }
maintainer Applied
#4 lore raw

Re: [net-2.6 PATCH 3/3] igb: fix link reporting when using sgmii

From: Jeff Kirsher <[email protected]>
Date: Fri, 30 Jan 2009 16:54:25 -0800

Quoted 6 lines

When using sgmii the link was not being properly passed up to the driver from the underlying link management functions. This change corrects it so that get_link_status is cleared when a link has been found.

Applied.