Skip to contentSkip to conversation

at91: add support for PM9263 board

RFC PATCH New Jean-Christophe PLAGNIOL-VILLARD 2 participants 3 messages Feb 4, 2009

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

RFC PATCH 1/1 at91: add support for PM9263 board

From: Ilko Iliev <[email protected]>

This patch adds support for the PM9263 board of Ronetix GmbH (www.ronetix.at) With the necessary to boot the board from NOR

---
 MAINTAINERS                                        |    4 +
 MAKEALL                                            |    1 +
 Makefile                                           |    3 +
 board/ronetix/pm9263/Makefile                      |   62 +++
 board/ronetix/pm9263/config.mk                     |    1 +
 .../lowlevel_init.S => board/ronetix/pm9263/led.c  |   51 ++-
 board/ronetix/pm9263/lowlevel_init.S               |  277 +++++++++++
 board/ronetix/pm9263/nand.c                        |   79 ++++
 board/ronetix/pm9263/partition.c                   |   47 ++
 board/ronetix/pm9263/pm9263.c                      |  493 ++++++++++++++++++++
 .../ronetix/pm9263/u-boot.lds                      |   49 ++-
 cpu/arm926ejs/at91/config.mk                       |    2 +
 cpu/arm926ejs/at91/lowlevel_init.S                 |    2 +
 include/asm-arm/arch-at91/at91sam9263.h            |    1 +
 include/asm-arm/arch-at91/at91sam9_sdramc.h        |   87 ++++
 include/asm-arm/arch-at91/hardware.h               |   17 +
 include/configs/pm9263.h                           |  350 ++++++++++++++
 tools/Makefile                                     |    3 +
 tools/logos/ronetix.bmp                            |  Bin 0 -> 5638 bytes
 19 files changed, 1498 insertions(+), 31 deletions(-)
 create mode 100644 board/ronetix/pm9263/Makefile
 create mode 100644 board/ronetix/pm9263/config.mk
 copy cpu/arm926ejs/at91/lowlevel_init.S => board/ronetix/pm9263/led.c (52%)
 create mode 100644 board/ronetix/pm9263/lowlevel_init.S
 create mode 100644 board/ronetix/pm9263/nand.c
 create mode 100644 board/ronetix/pm9263/partition.c
 create mode 100644 board/ronetix/pm9263/pm9263.c
 copy cpu/arm926ejs/at91/lowlevel_init.S => board/ronetix/pm9263/u-boot.lds (54%)
 create mode 100644 include/asm-arm/arch-at91/at91sam9_sdramc.h
 create mode 100644 include/configs/pm9263.h
 create mode 100644 tools/logos/ronetix.bmp
MAINTAINERS +4 -0
index 88cf1e9..216f35a 100644
@@ -204,6 +204,10 @@ Klaus Heydeck <[email protected]>
 	KUP4K		MPC855
 	KUP4X		MPC859
 
+Ilko Iliev <[email protected]>
+
+	PM9263		AT91SAM9263
+
 Gary Jennejohn <[email protected]>
 
 	quad100hd	PPC405EP
MAKEALL +1 -0
index e963f61..5f827eb 100755
@@ -561,6 +561,7 @@ LIST_at91="		\
 	kb9202		\
 	mp2usb		\
 	m501sk		\
+	pm9263		\
 "
 
 #########################################################################
Makefile +3 -0
index cc3a22e..6dcb80c 100644
@@ -2710,6 +2710,9 @@ at91sam9rlek_config	:	unconfig
 	fi;
 	@$(MKCONFIG) -a at91sam9rlek arm arm926ejs at91sam9rlek atmel at91
 
+pm9263_config	:	unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm926ejs pm9263 ronetix at91
+
 ########################################################################
 ## ARM Integrator boards - see doc/README-integrator for more info.
 integratorap_config	\
board/ronetix/pm9263/Makefile new file +62 -0

62 lines not on this page · raw message

board/ronetix/pm9263/config.mk new file +1 -0
new file mode 100644
index 0000000..ff2cfd1
@@ -0,0 +1 @@
+TEXT_BASE = 0x23f00000
board/ronetix/pm9263/led.c renamed from cpu/arm926ejs/at91/lowlevel_init.S +37 -14

66 lines not on this page · raw message

board/ronetix/pm9263/lowlevel_init.S new file +277 -0

277 lines not on this page · raw message

board/ronetix/pm9263/nand.c new file +79 -0

79 lines not on this page · raw message

board/ronetix/pm9263/partition.c new file +47 -0

47 lines not on this page · raw message

board/ronetix/pm9263/pm9263.c new file +493 -0

493 lines not on this page · raw message

board/ronetix/pm9263/u-boot.lds renamed from cpu/arm926ejs/at91/lowlevel_init.S +32 -17

61 lines not on this page · raw message

cpu/arm926ejs/at91/config.mk +2 -0
index 06177e6..eb33feb 100644
@@ -1,2 +1,4 @@
 PLATFORM_CPPFLAGS += $(call cc-option,-mtune=arm926ejs,)
+ifdef CONFIG_SKIP_LOWLEVEL_INIT
 LDSCRIPT := $(SRCTREE)/cpu/arm926ejs/at91/u-boot.lds
+endif
cpu/arm926ejs/at91/lowlevel_init.S +2 -0
index ec6ad5d..54b3f3d 100644
@@ -30,6 +30,8 @@
 #ifndef CONFIG_SKIP_LOWLEVEL_INIT
 
 .globl lowlevel_init
+.weak lowlevel_init
+.set lowlevel_init,function
 lowlevel_init:
 
 	/*
include/asm-arm/arch-at91/at91sam9263.h +1 -0
index 98251cb..07b265f 100644
@@ -106,6 +106,7 @@
 #define AT91_USART2	AT91SAM9263_BASE_US2
 
 #define AT91_SMC	AT91_SMC0
+#define AT91_SDRAMC	AT91_SDRAMC0
 
 /*
  * Internal Memory.
include/asm-arm/arch-at91/at91sam9_sdramc.h new file +87 -0

87 lines not on this page · raw message

include/asm-arm/arch-at91/hardware.h +17 -0
index b881e4e..4129d7b 100644
@@ -48,4 +48,21 @@
 #error "Unsupported AT91 processor"
 #endif
 
+/* External Memory Map */
+#define AT91_CHIPSELECT_0	0x10000000
+#define AT91_CHIPSELECT_1	0x20000000
+#define AT91_CHIPSELECT_2	0x30000000
+#define AT91_CHIPSELECT_3	0x40000000
+#define AT91_CHIPSELECT_4	0x50000000
+#define AT91_CHIPSELECT_5	0x60000000
+#define AT91_CHIPSELECT_6	0x70000000
+#define AT91_CHIPSELECT_7	0x80000000
+
+/* SDRAM */
+#ifdef CONFIG_DRAM_BASE
+#define AT91_SDRAM_BASE		CONFIG_DRAM_BASE
+#else
+#define AT91_SDRAM_BASE		AT91_CHIPSELECT_1
+#endif
+
 #endif
include/configs/pm9263.h new file +350 -0

350 lines not on this page · raw message

tools/Makefile +3 -0
index 9e9ee15..fbc64ba 100644
@@ -47,6 +47,9 @@ endif
 ifeq ($(VENDOR),atmel)
 LOGO_BMP= logos/atmel.bmp
 endif
+ifeq ($(VENDOR),ronetix)
+LOGO_BMP= logos/ronetix.bmp
+endif
 
 
 #-------------------------------------------------------------------------
tools/logos/ronetix.bmp new file binary +0 -0
new file mode 100644
index 0000000000000000000000000000000000000000..f956813915c7822ba11a3ab81ad9f48fa2849a5c
GIT binary patch

zBg8l!!DvjQg$o3*_l?ET0j9J)fMJnal at 1Z4oNCOcq#mc1o7j|EZaZXgJTSMW>2r zF*WC?mXqaxC-x|(WTDI=l$tk#FWHN38kTYnrx&8wI4+oux-1(qjL;>&<CJcNMwvtO zgR-IiDztQ?ZSWkr2*r{q-Vo<55|DVZ=fWNm9!14aK2VR=QEQiF;dSW7~UTjVl1*n zc!87JBXl3TAAa_3F`;l)3^>T-EQs-Uxs4I;w?ycg<Up88$U*F%9Oo{G2$}8M@<Nb z5~s)1PR$WECwuD}ZO!B{zH-$24xf+cIADT}+b8ll>{YMqiL(-*l2GFlJjrW#{3tc< zD!kQh56>87Y(nzsfPxjx@%dIhw@>sUb{Hl@$Ir5Z63w3!KZl1>0OGJ%f-Ai$BACt# zB*|x9m3&UGhlk;d*|;3{&XSfNZBB^0Tlq$1vuL*=fmAqHy~?kr|_{HfnJohUw|c8 z(&538B}t_C1)WFY(1aE<amk?tG2vGOvf?4dHGSs_#|}K at xwj5c~DMRe-J;$Zp%T9 z3@df2@R&Bw5nO_N6**1tF>3NPUrx4#|L%FQ##c75R0ASh;tL%|9dHEjeqVQ>|j7 zUw|Lut6ub?ho>ZwoL_t<U&WSQ%8hm$>R&muXJ={Md@(YL}~<nn^#~0=Y=^6}JW zdY|~Ym*kwlZf64lK5BI;iP|p&;HiA<iQFT68N%GPPk7lRFu(4A#=}J8y$@eTb~Ah6 zn=c0WsNVIM%G2R=J~k)O1fI+*GUOiLsGC$vlXlqtc6j&v&SSCraO4?yY~|Bq66>9O zY(Bj#nyese*InJsrXRZtCb+7iJ$VEj at lAVth7VxREA!Z9J at oBlIjp;PhUNP(?? z7aRIT142dxA-1KzmWKJnP|F^L2|Jt59I1*U3pT~K!k^~j8=BaK$5IMKxt at aaD?W>a z)izzw>(A&Zv%kKM4aTqO2&&De!|PEJ+y)E&9ekN78FfP)#ENg7=NUL-j!A&e3G+R# zDU;h-srEemtVw&hK6Eef6CrZLzCcUsPj4OPbGLkS+PyynBHU1ILNHKk4<y+yV0h zJ|=<<XE(?KU$&CZO=~>!dX+7I&hY^7t91#O=Wj{Zh$mOY5eCCTLX+_$m+xq~9p&u z{Gds(I*6r{y^0 at WD>f$fLw$?c2O)c+?&hYcf_F~_^Mab#w2)xv8RI)Z)h;~gXCkg zJSo6jdg3TRW0tAp5x4{Lcv0Lh&R<I|Uc9KgdVH(|)8buUbV2lm-q?hIr%Vw)r(fY= zG6!z{xE2 at T8v?+el-p5*n)3Wr75o?g0lu70I?A;&#)ROLPl5Zl&&P6l(pr0J2T4}# z!6aNQ+ZxZ3ht%@028<6ql{|3%oyO-T+ptcvp2bGA%;pXCZ1(%vz8|i(hWb4-<6U#T zj)4MP2H?&ZnbRk(+4)!n=jZsKieUW4OIcUx3Y)^R{f^Wj<!l?&j{q(MfD@V>hg|q z#u8Q}Lhq=7uG4d;i$!v53DTIHDQb4hBanA}5YvFMFJDVvW$TJ^DhxkHL12El1TJx^ zC~7NGR{W!!v1+CA>Xi<sTRuyk!)ImHOaMFl>o$m(t*rCcY;s7<-sf1#TRb%oShY z&4(XJPFCeOzCeD1H8Va0S99b)R0Tbl$NB<FCU+e=SjG0>K_;S^IzW3dt~sMt{VyI z1g&pj)STBZKbnO+Df3F}2;L_4PJgAn=fLA?jMx+VulJm8casoIK}x6A#|-s;d4^ zBSD7)dChC|;S2e~i9XdP4)8IjOC7u-dgso6-?C^=^zsoa?}<GU9}5iOJn`i>=YOSR NZ2eYzcz8HI_77a#1d{*&

literal 0
HcmV?d00001

Signature · 1 line
1.5.6.5
#1 lore raw

RFC PATCH 1/1 at91: add support for PM9263 board

Dear Jean-Christophe PLAGNIOL-VILLARD,

Quoted 4 lines · In message <[email protected]> you wrote:

From: Ilko Iliev <[email protected]>

This patch adds support for the PM9263 board of Ronetix GmbH (www.ronetix.at) With the necessary to boot the board from NOR

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

I cannot parse this. What do you want to express?

board/ronetix/pm9263/led.c

Quoted 3 lines

index ec6ad5d..122e23a 100644

board/ronetix/pm9263/led.c renamed from cpu/arm926ejs/at91/lowlevel_init.S +0 -0

NAK.

I will not accept yet another copy of this file. Please create common code that can be configured as needed.

board/ronetix/pm9263/partition.c

Quoted 5 lines
board/ronetix/pm9263/partition.c new file +0 -0
new file mode 100644
index 0000000..95ac398

NAK.

I will not accept yet another copy of this file. We have already 7 of these, most of them identical, and the remaining differences minimal. Please create common code that can be configured as needed.

Quoted 3 lines
board/ronetix/pm9263/pm9263.c new file +0 -0
new file mode 100644
index 0000000..7bda1b8

...

Quoted 21 lines
board/ronetix/pm9263/pm9263.c new file +21 -0
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+static void pm9263_serial_hw_init(void)
+{
+#ifdef CONFIG_USART0
+	at91_set_A_periph(AT91_PIN_PA26, 1);		/* TXD0 */
+	at91_set_A_periph(AT91_PIN_PA27, 0);		/* RXD0 */
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US0);
+#endif
+
+#ifdef CONFIG_USART1
+	at91_set_A_periph(AT91_PIN_PD0, 1);		/* TXD1 */
+	at91_set_A_periph(AT91_PIN_PD1, 0);		/* RXD1 */
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US1);
+#endif
+
+#ifdef CONFIG_USART2
+	at91_set_A_periph(AT91_PIN_PD2, 1);		/* TXD2 */

board/ronetix/pm9263/pm9263.c line 76

Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10 -0
+	at91_set_A_periph(AT91_PIN_PD3, 0);		/* RXD2 */
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US2);
+#endif
+
+#ifdef CONFIG_USART3	/* DBGU */
+	at91_set_A_periph(AT91_PIN_PC30, 0);		/* DRXD */
+	at91_set_A_periph(AT91_PIN_PC31, 1);		/* DTXD */
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_SYS);
+#endif
+}

I think I've seent his code a couple of times before, too. Last time in another patch earlier today. Seems there are at least 8 files in U-Boot that contain such a sequence, with no or just minimal differences.

Should we not clean this up, too?

Quoted 2 lines
board/ronetix/pm9263/pm9263.c new file +2 -0
+static int pm9263_lcd_hw_psram_init(void)
+{

...

board/ronetix/pm9263/pm9263.c

Quoted 2 lines
board/ronetix/pm9263/pm9263.c new file +2 -0
+	if ((readw(PHYS_PSRAM) != 0x1234) || (readw(PHYS_PSRAM+2) != 0x5678))
+	{

Incorrect brace style.

board/ronetix/pm9263/pm9263.c line 273

Quoted 4 lines
board/ronetix/pm9263/pm9263.c new file +4 -0
+		writew(0x5678, PHYS_PSRAM+2);
+		if ((readw(PHYS_PSRAM) != 0x1234)
+		   || (readw(PHYS_PSRAM + 2) != 0x5678))
+			return 1;

I recommend to use curly braces because of the multi-line "if".

Also, please put the "||" at the end of line 1.

board/ronetix/pm9263/pm9263.c line 417

Quoted 6 lines
board/ronetix/pm9263/pm9263.c new file +6 -0
+int dram_init(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	return 0;
+}

You should not hard-wire the memory size. You should auto-size it.

board/ronetix/pm9263/pm9263.c line 428

Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10 -0
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+#ifdef CONFIG_MACB
+	/*
+	 * Initialize ethernet HW addr prior to starting Linux,
+	 * needed for nfsroot
+	 */
+	eth_init(gd->bd);
+#endif

Be careful. You mustnot initialize the ehternet port unless a U-Boot network command is being used. And you must shut it down after that.

Quoted 6 lines
board/ronetix/pm9263/pm9263.c new file +6 -0
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard (void)
+{
+	char *ss;
+
+	uint32_t reg, diva, mula;

board/ronetix/pm9263/pm9263.c line 456

Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10 -0
+	uint32_t val, mdiv, pres, crystal;
+	char buf[32];
+
+	reg = at91_sys_read(AT91_CKGR_PLLAR);
+	mula = ((reg >> 16) & 0x7FF) + 1;
+	diva = reg & 0xFF;
+
+	reg = at91_sys_read(AT91_PMC_MCKR);
+	mdiv = (reg >> 8) & 3;
+	pres = (reg >> 2) & 7;

Maybe a comment would help to explain what this code is doing?

board/ronetix/pm9263/pm9263.c line 488

Quoted 1 line
board/ronetix/pm9263/pm9263.c new file +1 -0
+	printf("Video memory : 0x%08lX %s\n", gd->fb_base, ss );

No space before the paren.

board/ronetix/pm9263/pm9263.c line 490

Quoted 1 line
board/ronetix/pm9263/pm9263.c new file +1 -0
+	printf ("\n");

Please use consistent style: either

	printf(...);
or
	printf (...);

bot on;t mix these (this applies to all function calls).

board/ronetix/pm9263/u-boot.lds

Quoted 7 lines
board/ronetix/pm9263/u-boot.lds renamed from cpu/arm926ejs/at91/lowlevel_init.S +0 -0
similarity index 54%
copy from cpu/arm926ejs/at91/lowlevel_init.S
copy to board/ronetix/pm9263/u-boot.lds
index ec6ad5d..443f180 100644

That's a pretty funny diff, isn't it? lowlevel_init.S versus u-boot.lds ...

Quoted 5 lines
include/configs/pm9263.h new file +0 -0
new file mode 100644
index 0000000..4a20bff

...

Quoted 1 line

+#define AT91_MAIN_CLOCK (PM9263_CRYSTAL / MASTER_PLL_DIV * MASTER_PLL_MUL)

Maximum line lenght exceeded. Check all files, there are more places like this one!

include/configs/pm9263.h line 44

Quoted 3 lines
include/configs/pm9263.h new file +3 -0
+#define AT91_MASTER_CLOCK	(AT91_MAIN_CLOCK / MAIN_PLL_DIV)
+#define CONFIG_SYS_AT91_PLLB	0x10483E0E	/* PLLB settings for USB */
+#define CONFIG_SYS_HZ		1000000

NAK.

CONFIG_SYS_HZ must be 1000.

include/configs/pm9263.h line 247

Quoted 5 lines
include/configs/pm9263.h new file +5 -0
+#define CFG_MONITOR_BASE	(CFG_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400)
+#define CONFIG_ENV_OFFSET	0x4200
+#define CONFIG_ENV_ADDR		(CFG_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE		0x4200
+#define CONFIG_BOOTCOMMAND	"cp.b 0xC0042000 0x22000000 0x210000; bootm"

No need for 0x in U-Boot commands. This is just wasting environment memory.

Quoted 1 line

+#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000; bootm"

Ditto.

Quoted 1 line

+#define ROUND(A, B) (((A) + (B)) & ~((B) - 1))

Do we really need this redefined in each and every include/configs/at91*.h file?

Quoted 3 lines

+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)

Same here?

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
A supercomputer is a machine that runs an endless loop in 2 seconds.
#2 lore raw

RFC PATCH 1/1 at91: add support for PM9263 board

Quoted 10 lines · Wolfgang Denk

Dear Jean-Christophe PLAGNIOL-VILLARD,

Quoted 4 lines · In message <[email protected]> you wrote:

From: Ilko Iliev <[email protected]>

This patch adds support for the PM9263 board of Ronetix GmbH (www.ronetix.at) With the necessary to boot the board from NOR

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

I cannot parse this. What do you want to express?

I've not finish to clean the patch. I've send it for the update done in the at91 in order to implement boot from NOR

Quoted 18 lines

board/ronetix/pm9263/led.c

Quoted 4 lines

index ec6ad5d..122e23a 100644

board/ronetix/pm9263/led.c renamed from cpu/arm926ejs/at91/lowlevel_init.S +0 -0

NAK.

I will not accept yet another copy of this file. Please create common code that can be configured as needed.

board/ronetix/pm9263/partition.c

Quoted 5 lines
board/ronetix/pm9263/partition.c new file +0 -0
new file mode 100644
index 0000000..95ac398

NAK.

Quoted 3 lines

I will not accept yet another copy of this file. We have already 7 of these, most of them identical, and the remaining differences minimal. Please create common code that can be configured as needed.

It's plan to create it but I'll not have the time for this release and this board wait until December IIRC

Quoted 33 lines
Quoted 5 lines
board/ronetix/pm9263/pm9263.c new file +0 -0
new file mode 100644
index 0000000..7bda1b8

...

Quoted 2 lines
board/ronetix/pm9263/pm9263.c new file +2 -0
+static int pm9263_lcd_hw_psram_init(void)
+{

...

board/ronetix/pm9263/pm9263.c

Quoted 2 lines
board/ronetix/pm9263/pm9263.c new file +2 -0
+	if ((readw(PHYS_PSRAM) != 0x1234) || (readw(PHYS_PSRAM+2) != 0x5678))
+	{

Incorrect brace style.

board/ronetix/pm9263/pm9263.c line 273

Quoted 4 lines
board/ronetix/pm9263/pm9263.c new file +4 -0
+		writew(0x5678, PHYS_PSRAM+2);
+		if ((readw(PHYS_PSRAM) != 0x1234)
+		   || (readw(PHYS_PSRAM + 2) != 0x5678))
+			return 1;

I recommend to use curly braces because of the multi-line "if".

Also, please put the "||" at the end of line 1.

board/ronetix/pm9263/pm9263.c line 417

Quoted 6 lines
board/ronetix/pm9263/pm9263.c new file +6 -0
+int dram_init(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	return 0;
+}

You should not hard-wire the memory size. You should auto-size it.

Quoted 13 lines

board/ronetix/pm9263/pm9263.c line 428

Quoted 10 lines
board/ronetix/pm9263/pm9263.c new file +10 -0
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+#ifdef CONFIG_MACB
+	/*
+	 * Initialize ethernet HW addr prior to starting Linux,
+	 * needed for nfsroot
+	 */
+	eth_init(gd->bd);
+#endif

Be careful. You mustnot initialize the ehternet port unless a U-Boot network command is being used. And you must shut it down after that.

I known this will be fix in the final version

Quoted 11 lines

board/ronetix/pm9263/u-boot.lds

Quoted 8 lines
board/ronetix/pm9263/u-boot.lds renamed from cpu/arm926ejs/at91/lowlevel_init.S +0 -0
similarity index 54%
copy from cpu/arm926ejs/at91/lowlevel_init.S
copy to board/ronetix/pm9263/u-boot.lds
index ec6ad5d..443f180 100644

That's a pretty funny diff, isn't it? lowlevel_init.S versus u-boot.lds ...

yes do not known why

Best Regards,
J.