twl4030-gpio: Fix getting the value of the TWL4030 GPIO output pin
PATCH 1/1 twl4030-gpio: Fix getting the value of the TWL4030 GPIO output pin
If TWL4030 GPIO pin is output, must read the value from REG_GPIODATAOUTx register in twl4030_get_gpio_datainout().
---
drivers/gpio/twl4030-gpio.c +12 -2
@@ -183,7 +183,7 @@ static int twl4030_set_gpio_dataout(int gpio, int enable)return gpio_twl4030_write (base, d_msk); } -static int twl4030_get_gpio_datain (int gpio) +static int twl4030_get_gpio_datainout (int gpio) {u8 d_bnk = gpio >>3 ;u8 d_off = gpio &0x7 ;
@@ -194,7 +194,17 @@ static int twl4030_get_gpio_datain(int gpio) || !(gpio_usage_count & BIT(gpio))))return -EPERM ; - base =REG_GPIODATAIN1 + d_bnk; + base =REG_GPIODATADIR1 + d_bnk; + ret =gpio_twl4030_read (base); +if (ret >0 ) + ret = (ret >> d_off) &0x1 ; +else +return ret; + +if (ret) + base =REG_GPIODATAOUT1 + d_bnk; +else + base =REG_GPIODATAIN1 + d_bnk; ret =gpio_twl4030_read (base);if (ret >0 ) ret = (ret >> d_off) &0x1 ;
David Brownell
NAKQuoted 2 lines · Joonyoung Shim
If TWL4030 GPIO pin is output, must read the value from
REG_GPIODATAOUTxregister intwl4030_get_gpio_datainout().
Why "must"? The goal is to return the *actual* value of the pin, not the intended one. When an external signal overwhelms the drive capability of that GPIO -- just a couple mA -- the correct value to return can't be the value written in the output register.
Plus, this patch won't even link ... you changed the name of the function at its definition, but not at its use points.
NAK, unless you can show there's a real bug this addresses...
- Dave
2009/2/7 David Brownell <[email protected]>:
Quoted 8 lines · Joonyoung Shim
Quoted 2 lines
If TWL4030 GPIO pin is output, must read the value from
REG_GPIODATAOUTxregister intwl4030_get_gpio_datainout().Why "must"? The goal is to return the *actual* value of the pin, not the intended one. When an external signal overwhelms the drive capability of that GPIO -- just a couple mA -- the correct value to return can't be the value written in the output register.
but, it doesn't return actual value of the pin if twl4030 GPIO pin is output.
For example, the GPIO13 pin of twl4030 is configured as an output using gpio_direction_output() and assigns the GPIO's value to 1 using gpio_set_value_cansleep(), the result of "# cat /sys/kernel/debug/gpio" reports to me as follows.
GPIOs 192-209, platform/twl4030_gpio, twl4030, can sleep:
gpio-205 (keyled ) out lo
but it should have reported "hi" instead of "lo".
Quoted 3 lines
Plus, this patch won't even link ... you changed the name of the function at its definition, but not at its use points.
Sorry, i missed some code.
Quoted 5 lines
NAK, unless you can show there's a real bug this addresses...
- Dave
Quoted 1 line · Joonyoung Shim
but, it doesn't return actual value of the pin if twl4030 GPIO pin is output.
So it would seem that these GPIOs don't support bidirectional usage. Documentation/gpio.txt includes:
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
However, note that not all platforms can
read the value of output pins; those that can't should always return zero.
Which is exactly what's happening here, it seems...
Quoted 10 lines
For example, the GPIO13 pin of twl4030 is configured as an output using
gpio_direction_output()and assigns the GPIO's value to 1 usinggpio_set_value_cansleep(), the result of "# cat/sys/kernel/debug/gpio" reports to me as follows.GPIOs 192-209, platform/twl4030_gpio, twl4030, can sleep:
gpio-205 (keyled ) out lobut it should have reported "hi" instead of "lo".
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html