powerpc/83xx: Fix TSEC0 workability on MPC8313E-RDB boards
Subsystems (2)
PATCH 2/2 powerpc/83xx: Fix TSEC0 workability on MPC8313E-RDB boards
TSEC0 is connected to Vitesse 7385 5-port switch. The switch isn't connected to any mdio bus, the link to the switch is fixed to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
--- arch/powerpc/boot/dts/mpc8313erdb.dts | 9 ++------- arch/powerpc/configs/83xx/mpc8313_rdb_defconfig | 2 +- 2 files changed, 3 insertions(+), 8 deletions(-)
arch/powerpc/boot/dts/mpc8313erdb.dts +2 -7
@@ -191,7 +191,8 @@ interrupts = <37 0x8 36 0x8 35 0x8>; interrupt-parent = <&ipic>; tbi-handle = < &tbi0 >; - phy-handle = < &phy1 >; + /* Vitesse 7385 isn't on the MDIO bus */ + fixed-link = <1 1 1000 0 0>; fsl,magic-packet; mdio@24520 {
@@ -199,12 +200,6 @@ #size-cells = <0>; compatible = "fsl,gianfar-mdio"; reg = <0x24520 0x20>; - phy1: ethernet-phy@1 { - interrupt-parent = <&ipic>; - interrupts = <19 0x8>; - reg = <0x1>; - device_type = "ethernet-phy"; - }; phy4: ethernet-phy@4 { interrupt-parent = <&ipic>; interrupts = <20 0x8>;
arch/powerpc/configs/83xx/mpc8313_rdb_defconfig +1 -1
@@ -651,7 +651,7 @@ CONFIG_CICADA_PHY=y # CONFIG_NATIONAL_PHY is not set # CONFIG_STE10XP is not set # CONFIG_LSI_ET1011C_PHY is not set -# CONFIG_FIXED_PHY is not set +CONFIG_FIXED_PHY=y # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y
Signature · 1 line
1.5.6.5
Kumar Gala
AppliedQuoted 10 lines · Anton Vorontsov
TSEC0 is connected to Vitesse 7385 5-port switch. The switch isn't connected to any mdio bus, the link to the switch is fixed to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Quoted 5 lines
Signed-off-by Anton Vorontsov <[email protected]>---
arch/powerpc/boot/dts/mpc8313erdb.dts | 9 ++------- arch/powerpc/configs/83xx/mpc8313_rdb_defconfig | 2 +- 2 files changed, 3 insertions(+), 8 deletions(-)
applied to merge
- k
Quoted 3 lines · Anton Vorontsov
TSEC0 is connected to Vitesse 7385 5-port switch. The switch isn't connected to any mdio bus, the link to the switch is fixed to Full-duplex 1000 Mb/s (no pause).
It's a complex case for RDB boards. The revision A and revision B boards DO always connect TSEC0 to Vitesse switch. While the latest revision C board has one setting to connect TSEC0 to a Marvell PHY and MDIO bus. In BSP we have several DTS's for each setting of the board, shouldn't we do the same for upstream?
- Leo
Quoted 6 lines · Li Yang
It's a complex case for RDB boards. The revision A and revision B boards DO always connect TSEC0 to Vitesse switch. While the latest revision C board has one setting to connect TSEC0 to a Marvell PHY and MDIO bus. In BSP we have several DTS's for each setting of the board, shouldn't we do the same for upstream?
Is this something we can detect and deal with in u-boot? If not than having multiple .dts for the revisions seems like the only solution.
- k
PATCH 1/1 powerpc/83xx: Revive Marvell PHY option on MPC8313E-RDB rev. C boards
commit e85477f516c2de7ed515fcf94ceab5282eba7fa4 ("powerpc/83xx: Fix TSEC0 workability on MPC8313E-RDB boards") fixed TSEC0 workability for rev. A and rev. B boards by using fixed-link property for VSC 7385 5-port switch. But rev. C boards have an option where TSEC0 connected to a Marvell PHY, which is a normal PHY on MDIO bus.
So far U-Boot does not fix up TSEC0 nodes for MPC8313E-RDB boards, so we'd better include two device-tree files: one that specify Vitesse PHY and another for boards with Marvell PHY option.
---
Li, thanks for heads-up!
One thing though: documentation says that Marvell PHY address is 0x3, while old device tree and this patch:
http://www.bitshrine.org/gpp/linux-fsl-2.6.23-MPC8313ERDB-add-default-dts.patch
says "0x1"... I don't have any rev. C boards, so it would be great if somebody could confirm that 0x1 is the actual address.
arch/powerpc/boot/dts/mpc8313erdb_marvell_phy.dts | 401 +++++++++++++++++++++ arch/powerpc/configs/83xx/mpc8313_rdb_defconfig | 2 +- 2 files changed, 402 insertions(+), 1 deletions(-) create mode 100644 arch/powerpc/boot/dts/mpc8313erdb_marvell_phy.dts
arch/powerpc/boot/dts/mpc8313erdb_marvell_phy.dts new file +401 -0
@@ -0,0 +1,401 @@ +/* + * MPC8313E RDB Device Tree Source + * + * Copyright 2005, 2006, 2007 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; + +/ { + model = "MPC8313ERDB"; + compatible = "MPC8313ERDB", "MPC831xRDB", "MPC83xxRDB"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet0; + ethernet1 = &enet1; + serial0 = &serial0; + serial1 = &serial1; + pci0 = &pci0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,8313@0 { + device_type = "cpu"; + reg = <0x0>; + d-cache-line-size = <32>; + i-cache-line-size = <32>; + d-cache-size = <16384>; + i-cache-size = <16384>; + timebase-frequency = <0>; // from bootloader + bus-frequency = <0>; // from bootloader + clock-frequency = <0>; // from bootloader + }; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x08000000>; // 128MB at 0 + }; + + localbus@e0005000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8313-elbc", "fsl,elbc", "simple-bus"; + reg = <0xe0005000 0x1000>; + interrupts = <77 0x8>; + interrupt-parent = <&ipic>; + + // CS0 and CS1 are swapped when + // booting from nand, but the + // addresses are the same. + ranges = <0x0 0x0 0xfe000000 0x00800000 + 0x1 0x0 0xe2800000 0x00008000 + 0x2 0x0 0xf0000000 0x00020000 + 0x3 0x0 0xfa000000 0x00008000>; + + flash@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x800000>; + bank-width = <2>; + device-width = <1>; + }; + + nand@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8313-fcm-nand", + "fsl,elbc-fcm-nand"; + reg = <0x1 0x0 0x2000>; + + u-boot@0 { + reg = <0x0 0x100000>; + read-only; + }; + + kernel@100000 { + reg = <0x100000 0x300000>; + }; + + fs@400000 { + reg = <0x400000 0x1c00000>; + }; + }; + }; + + soc8313@e0000000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "simple-bus"; + ranges = <0x0 0xe0000000 0x00100000>; + reg = <0xe0000000 0x00000200>; + bus-frequency = <0>; + + wdt@200 { + device_type = "watchdog"; + compatible = "mpc83xx_wdt"; + reg = <0x200 0x100>; + }; + + sleep-nexus { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + sleep = <&pmc 0x03000000>; + ranges; + + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <14 0x8>; + interrupt-parent = <&ipic>; + dfsrr; + rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; + }; + + crypto@30000 { + compatible = "fsl,sec2.2", "fsl,sec2.1", + "fsl,sec2.0"; + reg = <0x30000 0x10000>; + interrupts = <11 0x8>; + interrupt-parent = <&ipic>; + fsl,num-channels = <1>; + fsl,channel-fifo-len = <24>; + fsl,exec-units-mask = <0x4c>; + fsl,descriptor-types-mask = <0x0122003f>; + }; + }; + + i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + compatible = "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <15 0x8>; + interrupt-parent = <&ipic>; + dfsrr; + }; + + spi@7000 { + cell-index = <0>; + compatible = "fsl,spi"; + reg = <0x7000 0x1000>; + interrupts = <16 0x8>; + interrupt-parent = <&ipic>; + mode = "cpu"; + }; + + /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */ + usb@23000 { + compatible = "fsl-usb2-dr"; + reg = <0x23000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&ipic>; + interrupts = <38 0x8>; + phy_type = "utmi_wide"; + sleep = <&pmc 0x00300000>; + }; + + enet0: ethernet@24000 { + #address-cells = <1>; + #size-cells = <1>; + sleep = <&pmc 0x20000000>; + ranges; + + cell-index = <0>; + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <37 0x8 36 0x8 35 0x8>; + interrupt-parent = <&ipic>; + tbi-handle = < &tbi0 >; + phy-handle = < &phy1 >; + fsl,magic-packet; + + mdio@24520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-mdio"; + reg = <0x24520 0x20>; + phy1: ethernet-phy@1 { + interrupt-parent = <&ipic>; + interrupts = <19 0x8>; + reg = <0x1>; + device_type = "ethernet-phy"; + }; + phy4: ethernet-phy@4 { + interrupt-parent = <&ipic>; + interrupts = <20 0x8>; + reg = <0x4>; + device_type = "ethernet-phy"; + }; + tbi0: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + }; + + enet1: ethernet@25000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <1>; + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar"; + reg = <0x25000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <34 0x8 33 0x8 32 0x8>; + interrupt-parent = <&ipic>; + tbi-handle = < &tbi1 >; + phy-handle = < &phy4 >; + sleep = <&pmc 0x10000000>; + fsl,magic-packet; + + mdio@25520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-tbi"; + reg = <0x25520 0x20>; + + tbi1: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + + + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <0>; + interrupts = <9 0x8>; + interrupt-parent = <&ipic>; + }; + + serial1: serial@4600 { + cell-index = <1>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4600 0x100>; + clock-frequency = <0>; + interrupts = <10 0x8>; + interrupt-parent = <&ipic>; + }; + + /* IPIC + * interrupts cell = <intr #, sense> + * sense values match linux IORESOURCE_IRQ_* defines: + * sense == 8: Level, low assertion + * sense == 2: Edge, high-to-low change + */ + ipic: pic@700 { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x700 0x100>; + device_type = "ipic"; + }; + + pmc: power@b00 { + compatible = "fsl,mpc8313-pmc", "fsl,mpc8349-pmc"; + reg = <0xb00 0x100 0xa00 0x100>; + interrupts = <80 8>; + interrupt-parent = <&ipic>; + fsl,mpc8313-wakeup-timer = <>m1>; + + /* Remove this (or change to "okay") if you have + * a REVA3 or later board, if you apply one of the + * workarounds listed in section 8.5 of the board + * manual, or if you are adapting this device tree + * to a different board. + */ + status = "fail"; + }; + + gtm1: timer@500 { + compatible = "fsl,mpc8313-gtm", "fsl,gtm"; + reg = <0x500 0x100>; + interrupts = <90 8 78 8 84 8 72 8>; + interrupt-parent = <&ipic>; + }; + + timer@600 { + compatible = "fsl,mpc8313-gtm", "fsl,gtm"; + reg = <0x600 0x100>; + interrupts = <91 8 79 8 85 8 73 8>; + interrupt-parent = <&ipic>; + }; + }; + + sleep-nexus { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + sleep = <&pmc 0x00010000>; + ranges; + + pci0: pci@e0008500 { + cell-index = <1>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0E -mini PCI */ + 0x7000 0x0 0x0 0x1 &ipic 18 0x8 + 0x7000 0x0 0x0 0x2 &ipic 18 0x8 + 0x7000 0x0 0x0 0x3 &ipic 18 0x8 + 0x7000 0x0 0x0 0x4 &ipic 18 0x8 + + /* IDSEL 0x0F - PCI slot */ + 0x7800 0x0 0x0 0x1 &ipic 17 0x8 + 0x7800 0x0 0x0 0x2 &ipic 18 0x8 + 0x7800 0x0 0x0 0x3 &ipic 17 0x8 + 0x7800 0x0 0x0 0x4 &ipic 18 0x8>; + interrupt-parent = <&ipic>; + interrupts = <66 0x8>; + bus-range = <0x0 0x0>; + ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 + 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 + 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; + clock-frequency = <66666666>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ + compatible = "fsl,mpc8349-pci"; + device_type = "pci"; + }; + + dma@82a8 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8313-dma", "fsl,elo-dma"; + reg = <0xe00082a8 4>; + ranges = <0 0xe0008100 0x1a8>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + + dma-channel@0 { + compatible = "fsl,mpc8313-dma-channel", + "fsl,elo-dma-channel"; + reg = <0 0x28>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <0>; + }; + + dma-channel@80 { + compatible = "fsl,mpc8313-dma-channel", + "fsl,elo-dma-channel"; + reg = <0x80 0x28>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <1>; + }; + + dma-channel@100 { + compatible = "fsl,mpc8313-dma-channel", + "fsl,elo-dma-channel"; + reg = <0x100 0x28>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <2>; + }; + + dma-channel@180 { + compatible = "fsl,mpc8313-dma-channel", + "fsl,elo-dma-channel"; + reg = <0x180 0x28>; + interrupt-parent = <&ipic>; + interrupts = <71 8>; + cell-index = <3>; + }; + }; + }; +};
arch/powerpc/configs/83xx/mpc8313_rdb_defconfig +1 -1
@@ -638,7 +638,7 @@ CONFIG_PHYLIB=y # # MII PHY device drivers # -# CONFIG_MARVELL_PHY is not set +CONFIG_MARVELL_PHY=y # CONFIG_DAVICOM_PHY is not set # CONFIG_QSEMI_PHY is not set # CONFIG_LXT_PHY is not set
Signature · 1 line
1.5.6.5
Re: [PATCH] powerpc/83xx: Revive Marvell PHY option on MPC8313E-RDB rev. C boards
Quoted 21 lines · Anton Vorontsov
commit
e85477f516c2de7ed515fcf94ceab5282eba7fa4("powerpc/83xx: Fix TSEC0 workability on MPC8313E-RDB boards") fixed TSEC0 workability for rev. A and rev. B boards by using fixed-link property for VSC 7385 5-port switch. But rev. C boards have an option where TSEC0 connected to a Marvell PHY, which is a normal PHY on MDIO bus.So far U-Boot does not fix up TSEC0 nodes for MPC8313E-RDB boards, so we'd better include two device-tree files: one that specify Vitesse PHY and another for boards with Marvell PHY option.
Reported-by Li Yang <[email protected]>Signed-off-by Anton Vorontsov <[email protected]>---
Li, thanks for heads-up!
One thing though: documentation says that Marvell PHY address is
0x3, while old device tree and this patch:http://www.bitshrine.org/gpp/linux-fsl-2.6.23-MPC8313ERDB-add-default-dts.patch
Quoted 8 lines
says "
0x1"... I don't have any rev. C boards, so it would be great if somebody could confirm that0x1is the actual address.
arch/powerpc/boot/dts/mpc8313erdb_marvell_phy.dts| 401 ++++++++++++
+++++++++arch/powerpc/configs/83xx/mpc8313_rdb_defconfig| 2 +-2 files changed, 402 insertions(+), 1 deletions(-)create mode 100644
arch/powerpc/boot/dts/mpc8313erdb_marvell_phy.dts
did we decide that we don't have any bcsr or something that convey board rev or this setting?
- k
RE: [PATCH] powerpc/83xx: Revive Marvell PHY option on MPC8313E-RDB rev. C boards
Quoted 44 lines
-----Original Message-----
From: Kumar Gala [mailto:[email protected]]=20
Sent: Tuesday, February 10, 2009 11:31 PM
To: [email protected]
Cc: Li Yang-R58472; [email protected]
Subject: Re: [PATCH] powerpc/83xx: Revive Marvell PHY option=20 on MPC8313E-RDB rev. C boards
=20
=20
On Feb 10, 2009, at 9:10 AM, Anton Vorontsov wrote:
=20Quoted 2 lines
commit
e85477f516c2de7ed515fcf94ceab5282eba7fa4("powerpc/83xx: Fix=20 TSEC0 workability on MPC8313E-RDB boards") fixed TSEC0=20workability for=20
Quoted 2 lines
rev. A and rev. B boards by using fixed-link property for VSC 7385=20 5-port switch. But rev. C boards have an option where TSEC0=20
connected=20
Quoted 3 lines
to a Marvell PHY, which is a normal PHY on MDIO bus.
So far U-Boot does not fix up TSEC0 nodes for MPC8313E-RDB=20
boards, so=20
Quoted 10 lines
we'd better include two device-tree files: one that specify Vitesse=20 PHY and another for boards with Marvell PHY option.
Reported-by Li Yang <[email protected]>Signed-off-by Anton Vorontsov <[email protected]>---
Li, thanks for heads-up!
One thing though: documentation says that Marvell PHY=20
address is 0x3,=20
Quoted 3 lines
while old device tree and this patch:
=20
http://www.bitshrine.org/gpp/linux-fsl-2.6.23-MPC8313ERDB-add-default-
Quoted 3 lines
dts.patch
says "
0x1"... I don't have any rev. C boards, so it would=20be great if=20
Quoted 3 lines
somebody could confirm that
0x1is the actual address.
arch/powerpc/boot/dts/mpc8313erdb_marvell_phy.dts| 401=20++++++++++++
Quoted 8 lines
Quoted 3 lines
+++++++++
arch/powerpc/configs/83xx/mpc8313_rdb_defconfig| 2 +-2 files changed, 402 insertions(+), 1 deletions(-) create=20mode 100644=20
Quoted 1 line
arch/powerpc/boot/dts/mpc8313erdb_marvell_phy.dts=20
did we decide that we don't have any bcsr or something that=20 convey board rev or this setting?
Nope for now. The board do have two revision bits readable to the core, one bit set by resisters and the other set by a switch. We don't currently have a convention for using these two bits. And apperently they can't cover the information of both the board revision and setup.
- Leo
Re: [PATCH] powerpc/83xx: Revive Marvell PHY option on MPC8313E-RDB rev. C boards
Quoted 44 lines
Quoted 35 lines · Anton Vorontsov
Quoted 3 lines
commit
e85477f516c2de7ed515fcf94ceab5282eba7fa4("powerpc/83xx: Fix TSEC0 workability on MPC8313E-RDB boards") fixed TSEC0workability for
Quoted 2 lines
rev. A and rev. B boards by using fixed-link property for VSC 7385 5-port switch. But rev. C boards have an option where TSEC0
connected
Quoted 3 lines
to a Marvell PHY, which is a normal PHY on MDIO bus.
So far U-Boot does not fix up TSEC0 nodes for MPC8313E-RDB
boards, so
Quoted 10 lines
we'd better include two device-tree files: one that specify Vitesse PHY and another for boards with Marvell PHY option.
Reported-by Li Yang <[email protected]>Signed-off-by Anton Vorontsov <[email protected]>---
Li, thanks for heads-up!
One thing though: documentation says that Marvell PHY
address is
0x3,Quoted 3 lines
while old device tree and this patch:
http://www.bitshrine.org/gpp/linux-fsl-2.6.23-MPC8313ERDB-add-default-
Quoted 3 lines
dts.patch
says "
0x1"... I don't have any rev. C boards, so it wouldbe great if
Quoted 3 lines
somebody could confirm that
0x1is the actual address.
arch/powerpc/boot/dts/mpc8313erdb_marvell_phy.dts| 401++++++++++++
Quoted 8 lines
Quoted 3 lines
+++++++++
arch/powerpc/configs/83xx/mpc8313_rdb_defconfig| 2 +-2 files changed, 402 insertions(+), 1 deletions(-) createmode 100644
Quoted 1 line
arch/powerpc/boot/dts/mpc8313erdb_marvell_phy.dtsdid we decide that we don't have any bcsr or something that convey board rev or this setting?
Quoted 6 lines
Nope for now. The board do have two revision bits readable to the core, one bit set by resisters and the other set by a switch. We don't currently have a convention for using these two bits. And apperently they can't cover the information of both the board revision and setup.
- Leo
ok. I'll take the patch pending the other question Anton raised about the phy id.
- k
Re: [PATCH] powerpc/83xx: Revive Marvell PHY option on MPC8313E-RDB rev. C boards
In reply to Anton VorontsovQuoted 10 lines · Anton Vorontsov
Li, thanks for heads-up!
One thing though: documentation says that Marvell PHY address is
0x3, while old device tree and this patch:http://www.bitshrine.org/gpp/linux-fsl-2.6.23-MPC8313ERDB-add-default-dts.patch
says "
0x1"... I don't have any rev. C boards, so it would be great if somebody could confirm that0x1is the actual address.
Leo, on comments on this?
- k
RE: [PATCH] powerpc/83xx: Revive Marvell PHY option on MPC8313E-RDB rev. C boards
Quoted 16 lines
-----Original Message-----
From: Kumar Gala [mailto:[email protected]]=20
Sent: Thursday, February 12, 2009 1:25 PM
To: Li Yang-R58472
Cc: linuxppc-dev list; Anton Vorontsov
Subject: Re: [PATCH] powerpc/83xx: Revive Marvell PHY option=20 on MPC8313E-RDB rev. C boards
=20
=20
On Feb 10, 2009, at 9:10 AM, Anton Vorontsov wrote:
=20Quoted 4 lines
Li, thanks for heads-up!
One thing though: documentation says that Marvell PHY=20
address is 0x3,=20
Quoted 9 lines
Quoted 3 lines
while old device tree and this patch:
=20
http://www.bitshrine.org/gpp/linux-fsl-2.6.23-MPC8313ERDB-add-default-
Quoted 3 lines
dts.patch
says "
0x1"... I don't have any rev. C boards, so it would=20be great if=20
Quoted 1 line
somebody could confirm that
0x1is the actual address.
The correct address is 0x3. The previous patch in revB BSP used a guess value before the revC documentation is available. The latest BSP has been updated to use the correct address.
- Leo
Re: [PATCH] powerpc/83xx: Revive Marvell PHY option on MPC8313E-RDB rev. C boards
Quoted 22 lines · On Feb 11, 2009, at 11:40 PM, Li Yang-R58472 wrote:
Quoted 22 lines
-----Original Message-----
From: Kumar Gala [mailto:[email protected]]
Sent: Thursday, February 12, 2009 1:25 PM
To: Li Yang-R58472
Cc: linuxppc-dev list; Anton Vorontsov
Subject: Re: [PATCH] powerpc/83xx: Revive Marvell PHY option on MPC8313E-RDB rev. C boardsQuoted 4 lines · Anton Vorontsov
Li, thanks for heads-up!
One thing though: documentation says that Marvell PHY
address is
0x3,Quoted 3 lines
while old device tree and this patch:
http://www.bitshrine.org/gpp/linux-fsl-2.6.23-MPC8313ERDB-add-default-
Quoted 2 lines
dts.patch
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
says "
0x1"... I don't have any rev. C boards, so it wouldbe great if
Quoted 1 line
somebody could confirm that
0x1is the actual address.The correct address is
0x3. The previous patch in revB BSP used a guess value before the revC documentation is available. The latest BSP has been updated to use the correct address.
Anton, will you spin a new patch with this change?
- k
Re: [PATCH] powerpc/83xx: Revive Marvell PHY option on MPC8313E-RDB rev. C boards
Quoted 14 lines · Kumar Gala
Quoted 13 lines · On Feb 11, 2009, at 11:40 PM, Li Yang-R58472 wrote:
Quoted 13 lines
Quoted 3 lines
Li, thanks for heads-up!
One thing though: documentation says that Marvell PHY
address is
0x3,Quoted 3 lines
while old device tree and this patch:
http://www.bitshrine.org/gpp/linux-fsl-2.6.23-MPC8313ERDB-add-
default-Quoted 3 lines
dts.patch
says "
0x1"... I don't have any rev. C boards, so it wouldbe great if
Quoted 8 lines
Quoted 6 lines
Quoted 1 line
Quoted 1 line
somebody could confirm that
0x1is the actual address.The correct address is
0x3. The previous patch in revB BSP used a guess
value before the revC documentation is available. The latest BSP has been updated to use the correct address.Anton, will you spin a new patch with this change?
Since the correct address is 0x3, that means that the old device tree never worked on rev. C boards, thus there is no regression. And furthermore, it appears that U-Boot doesn't support Marvell PHY option either.
So, I don't think that adding the new device tree makes any sense now.
I think the better option would be to implement Marvell PHY support in U-Boot, and at the same time teach U-Boot to fixup 8313rdb's device tree depending on the environment variable (something like setenv marvell_phy_option yes/no), i.e. like I did for MPC8315E-RDB's ULPI/TSEC1 options:
http://lists.denx.de/pipermail/u-boot/2008-July/036553.html
Makes sense? If not, I'll readily respin this patch with the PHY address change.
Thanks,
Signature · 3 lines
Anton Vorontsov email: [email protected] irc://irc.freenode.net/bd2
RE: [PATCH] powerpc/83xx: Revive Marvell PHY option onMPC8313E-RDB rev. C boards
Quoted 30 lines
-----Original Message-----
From: Anton Vorontsov [mailto:[email protected]]=20
Sent: Friday, February 13, 2009 9:18 AM
To: Kumar Gala
Cc: linuxppc-dev list; Li Yang-R58472
Subject: Re: [PATCH] powerpc/83xx: Revive Marvell PHY option=20 onMPC8313E-RDB rev. C boards
=20Quoted 10 lines · Kumar Gala
Quoted 9 lines · On Feb 11, 2009, at 11:40 PM, Li Yang-R58472 wrote:
Quoted 9 lines
Quoted 3 lines
Li, thanks for heads-up!
One thing though: documentation says that Marvell PHY
address is
0x3,Quoted 3 lines
while old device tree and this patch:
http://www.bitshrine.org/gpp/linux-fsl-2.6.23-MPC8313ERDB-add-
default-Quoted 8 lines
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
dts.patch
says "
0x1"... I don't have any rev. C boards, so it wouldbe great if
Quoted 1 line
somebody could confirm that
0x1is the actual address.The correct address is
0x3. The previous patch in revB BSP used a=20 guess value before the revC documentation is available. =20The latest=20
Quoted 2 lines
Quoted 1 line
BSP has been updated to use the correct address.
Quoted 7 lines
Quoted 1 line
Anton, will you spin a new patch with this change?
=20
Since the correct address is0x3, that means that the old=20 device tree never worked on rev. C boards, thus there is no=20 regression.
And furthermore, it appears that U-Boot doesn't support=20 Marvell PHY option either.
No regression but to be more updated. RevC boards are newly introduced.
Quoted 10 lines
=20
So, I don't think that adding the new device tree makes any sense now. =20
I think the better option would be to implement Marvell PHY=20 support in U-Boot, and at the same time teach U-Boot to fixup=20 8313rdb's device tree depending on the environment variable=20 (something like setenvmarvell_phy_optionyes/no), i.e. like=20 I did for MPC8315E-RDB's ULPI/TSEC1 options:
=20
http://lists.denx.de/pipermail/u-boot/2008-July/036553.html
This approach is surely more user friendly.
- Leo