Skip to contentSkip to conversation

ppc4xx: Cleanup PMC405 board support

PATCH New Matthias Fuchs 3 participants 8 messages Feb 15, 2009 – Feb 18, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ppc4xx: Cleanup PMC405 board support

This patch fixes coding style for PMC405 board support. Also some unneeded features/code is removed.

---
 board/esd/pmc405/pmc405.c |   95 ++++-----------
 include/configs/PMC405.h  |  285 ++++++++++++++++++++++-----------------------
 2 files changed, 165 insertions(+), 215 deletions(-)
board/esd/pmc405/pmc405.c +25 -70
index 975b6d6..dd58d01 100644
@@ -40,7 +40,6 @@ const unsigned char fpgadata[] =
 };
 int filesize = sizeof(fpgadata);
 
-
 int board_early_init_f (void)
 {
 	/*
@@ -55,23 +54,23 @@ int board_early_init_f (void)
 	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
 	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
 	 */
-	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
-	mtdcr(uicer, 0x00000000);       /* disable all ints */
-	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
-	mtdcr(uicpr, 0xFFFFFF81);       /* set int polarities */
-	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
-	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest priority*/
-	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+	mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
+	mtdcr(uicer, 0x00000000); /* disable all ints */
+	mtdcr(uiccr, 0x00000000); /* set all to be non-critical*/
+	mtdcr(uicpr, 0xFFFFFF81); /* set int polarities */
+	mtdcr(uictr, 0x10000000); /* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001); /* set vect base=0, INT0 highest priority */
+	mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
 
 	/*
-	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
+	 * EBC Configuration Register:
+	 * set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
 	mtebc (epcr, 0xa8400000);
 
 	/*
 	 * Setup GPIO pins
 	 */
-
 	mtdcr(cntrl0, mfdcr(cntrl0) | ((CONFIG_SYS_FPGA_INIT | \
 					CONFIG_SYS_FPGA_DONE | \
 					CONFIG_SYS_XEREADY | \
@@ -85,26 +84,26 @@ int board_early_init_f (void)
 	}
 
 	out32(GPIO0_OR, 0);
-	out32(GPIO0_TCR, CONFIG_SYS_FPGA_PRG | CONFIG_SYS_FPGA_CLK | CONFIG_SYS_FPGA_DATA | CONFIG_SYS_XEREADY); /* setup for output */
+	/* setup for output */
+	out32(GPIO0_TCR, CONFIG_SYS_FPGA_PRG | CONFIG_SYS_FPGA_CLK | \
+	      CONFIG_SYS_FPGA_DATA | CONFIG_SYS_XEREADY);
 
-	/* - check if rev1_2 is low, then:
-	 * - set/reset CONFIG_SYS_INTA_FAKE/CONFIG_SYS_SELF_RST in TCR to assert INTA# or SELFRST#
+	/*
+	 * - check if rev1_2 is low, then:
+	 * - set/reset CONFIG_SYS_INTA_FAKE/CONFIG_SYS_SELF_RST
+	 *   in TCR to assert INTA# or SELFRST#
 	 */
-
 	return 0;
 }
 
-
-/* ------------------------------------------------------------------------- */
-
-
 int misc_init_r (void)
 {
 	/* adjust flash start and offset */
 	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
 	gd->bd->bi_flashoffset = 0;
 
-	out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_XEREADY); /* deassert EREADY# */
+	/* deassert EREADY# */
+	out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_XEREADY);
 	return (0);
 }
 
@@ -113,16 +112,16 @@ ushort pmc405_pci_subsys_deviceid(void)
 	ulong val;
 	val = in32(GPIO0_IR);
 	if (!(val & CONFIG_SYS_REV1_2)) { /* low=rev1.2 */
-		if (val & CONFIG_SYS_NONMONARCH) { /* monarch# signal */
+		/* check monarch# signal */
+		if (val & CONFIG_SYS_NONMONARCH)
 			return CONFIG_SYS_PCI_SUBSYS_DEVICEID_NONMONARCH;
-		}
 		return CONFIG_SYS_PCI_SUBSYS_DEVICEID_MONARCH;
 	}
 	return CONFIG_SYS_PCI_SUBSYS_DEVICEID_NONMONARCH;
 }
 
 /*
- * Check Board Identity:
+ * Check Board Identity
  */
 int checkboard (void)
 {
@@ -133,29 +132,25 @@ int checkboard (void)
 
 	puts ("Board: ");
 
-	if (i == -1) {
+	if (i == -1)
 		puts ("### No HW ID - assuming PMC405");
-	} else {
+	else
 		puts(str);
-	}
 
 	val = in32(GPIO0_IR);
 	if (!(val & CONFIG_SYS_REV1_2)) { /* low=rev1.2 */
 		puts(" rev1.2 (");
-		if (val & CONFIG_SYS_NONMONARCH) { /* monarch# signal */
+		if (val & CONFIG_SYS_NONMONARCH) /* monarch# signal */
 			puts("non-");
-		}
 		puts("monarch)");
-	} else {
+	} else
 		puts(" <=rev1.1");
-	}
 
 	putc ('\n');
 
 	return 0;
 }
 
-/* ------------------------------------------------------------------------- */
 void reset_phy(void)
 {
 #ifdef CONFIG_LXT971_NO_SLEEP
@@ -166,43 +161,3 @@ void reset_phy(void)
 	lxt971_no_sleep();
 #endif
 }
-
-
-int do_cantest(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
-{
-	ulong addr;
-	volatile uchar *ptr;
-	volatile uchar val;
-	int i;
-
-	addr = simple_strtol (argv[1], NULL, 16) + 0x16;
-
-	i = 0;
-	for (;;) {
-		ptr = (uchar *)addr;
-		for (i=0; i<8; i++) {
-			*ptr = i;
-			val = *ptr;
-
-			if (val != i) {
-				printf("ERROR: addr=%p write=0x%02X, read=0x%02X\n", ptr, i, val);
-				return 0;
-			}
-
-			/* Abort if ctrl-c was pressed */
-			if (ctrlc()) {
-				puts("\nAbort\n");
-				return 0;
-			}
-
-			ptr++;
-		}
-	}
-
-	return 0;
-}
-U_BOOT_CMD(
-	cantest,	3,	1,	do_cantest,
-	"Test CAN controller",
-	NULL
-	);
include/configs/PMC405.h +140 -145

450 lines not on this page · raw message

Signature · 1 line
1.5.6.3
#1 lore raw

PATCH 1/1 ppc4xx: Cleanup PMC405 board support

Quoted 2 lines · Matthias Fuchs

This patch fixes coding style for PMC405 board support. Also some unneeded features/code is removed.

Please find some comments below.

Quoted 59 lines
---
 board/esd/pmc405/pmc405.c |   95 ++++-----------
 include/configs/PMC405.h  |  285

++++++++++++++++++++++----------------------- 2 files changed, 165 insertions(+), 215 deletions(-)

board/esd/pmc405/pmc405.c +0 -7
index 975b6d6..dd58d01 100644
@@ -40,7 +40,6 @@ const unsigned char fpgadata[] =
 };
 int filesize = sizeof(fpgadata);
 
-
 int board_early_init_f (void)
 {
 	/*
@@ -55,23 +54,23 @@ int board_early_init_f (void)
 	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
 	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
 	 */
-	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
-	mtdcr(uicer, 0x00000000);       /* disable all ints */
-	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
-	mtdcr(uicpr, 0xFFFFFF81);       /* set int polarities */
-	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
-	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest

priority*/ - mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */

board/esd/pmc405/pmc405.c +7 -1
+	mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
+	mtdcr(uicer, 0x00000000); /* disable all ints */
+	mtdcr(uiccr, 0x00000000); /* set all to be non-critical*/
+	mtdcr(uicpr, 0xFFFFFF81); /* set int polarities */
+	mtdcr(uictr, 0x10000000); /* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001); /* set vect base=0, INT0 highest priority */
+	mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
 
 	/*
-	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca.

15 us + * EBC Configuration Register:

board/esd/pmc405/pmc405.c +1 -2
+	 * set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
 	mtebc (epcr, 0xa8400000);
 
 	/*
 	 * Setup GPIO pins
 	 */
-
 	mtdcr(cntrl0, mfdcr(cntrl0) | ((CONFIG_SYS_FPGA_INIT | \
 					CONFIG_SYS_FPGA_DONE | \
 					CONFIG_SYS_XEREADY | \
@@ -85,26 +84,26 @@ int board_early_init_f (void)
 	}
 
 	out32(GPIO0_OR, 0);
-	out32(GPIO0_TCR, CONFIG_SYS_FPGA_PRG | CONFIG_SYS_FPGA_CLK |

CONFIG_SYS_FPGA_DATA | CONFIG_SYS_XEREADY); /* setup for output */ + /*
setup for output */

board/esd/pmc405/pmc405.c int board_early_init_f (void) · line 89

Quoted 2 lines
board/esd/pmc405/pmc405.c +2 -0
+	out32(GPIO0_TCR, CONFIG_SYS_FPGA_PRG | CONFIG_SYS_FPGA_CLK | \
+	      CONFIG_SYS_FPGA_DATA | CONFIG_SYS_XEREADY);

I suggest to switch to using the out_be32()/in_be32() accessor functions instead. I am aware that many other 4xx boards still use the "wrong" accessor functions for initial GPIO configuration. I'll try to change this soon.

Thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#2 lore raw

PATCH 1/1 ppc4xx: Cleanup PMC405 board support

Quoted 61 lines · Stefan Roese
Quoted 2 lines · Matthias Fuchs

This patch fixes coding style for PMC405 board support. Also some unneeded features/code is removed.

Please find some comments below.

Quoted 55 lines
---
 board/esd/pmc405/pmc405.c |   95 ++++-----------
 include/configs/PMC405.h  |  285

++++++++++++++++++++++----------------------- 2 files changed, 165 insertions(+), 215 deletions(-)

board/esd/pmc405/pmc405.c +0 -7
index 975b6d6..dd58d01 100644
@@ -40,7 +40,6 @@ const unsigned char fpgadata[] =
 };
 int filesize = sizeof(fpgadata);
 
-
 int board_early_init_f (void)
 {
 	/*
@@ -55,23 +54,23 @@ int board_early_init_f (void)
 	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
 	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
 	 */
-	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
-	mtdcr(uicer, 0x00000000);       /* disable all ints */
-	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
-	mtdcr(uicpr, 0xFFFFFF81);       /* set int polarities */
-	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
-	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest

priority*/ - mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */

board/esd/pmc405/pmc405.c +7 -1
+	mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
+	mtdcr(uicer, 0x00000000); /* disable all ints */
+	mtdcr(uiccr, 0x00000000); /* set all to be non-critical*/
+	mtdcr(uicpr, 0xFFFFFF81); /* set int polarities */
+	mtdcr(uictr, 0x10000000); /* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001); /* set vect base=0, INT0 highest priority */
+	mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
 
 	/*
-	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca.

15 us + * EBC Configuration Register:

board/esd/pmc405/pmc405.c +1 -1
+	 * set ready timeout to 512 ebc-clks -> ca. 15 us
 	 */
 	mtebc (epcr, 0xa8400000);
 
 	/*
 	 * Setup GPIO pins
 	 */
-
 	mtdcr(cntrl0, mfdcr(cntrl0) | ((CONFIG_SYS_FPGA_INIT | \
 					CONFIG_SYS_FPGA_DONE | \
 					CONFIG_SYS_XEREADY | \
@@ -85,26 +84,26 @@ int board_early_init_f (void)
 	}
 
Quoted 10 lines

board/esd/pmc405/pmc405.c int board_early_init_f (void) · line 89

Quoted 6 lines
board/esd/pmc405/pmc405.c +0 -1
 	out32(GPIO0_OR, 0);
-	out32(GPIO0_TCR, CONFIG_SYS_FPGA_PRG | CONFIG_SYS_FPGA_CLK |

CONFIG_SYS_FPGA_DATA | CONFIG_SYS_XEREADY); /* setup for output */ + /*
setup for output */

board/esd/pmc405/pmc405.c +2 -0
+	out32(GPIO0_TCR, CONFIG_SYS_FPGA_PRG | CONFIG_SYS_FPGA_CLK | \
+	      CONFIG_SYS_FPGA_DATA | CONFIG_SYS_XEREADY);

I suggest to switch to using the out_be32()/in_be32() accessor functions instead. I am aware that many other 4xx boards still use the "wrong" accessor functions for initial GPIO configuration. I'll try to change this soon.

You are right I missed these. I will update the patch and resend. I will also fix the other esd boards in the next days.

Matthias

#3 lore raw

PATCH 1/1 ppc4xx: Cleanup PMC405 board support

Quoted 7 lines · Matthias Fuchs
Quoted 4 lines

I suggest to switch to using the out_be32()/in_be32() accessor functions instead. I am aware that many other 4xx boards still use the "wrong" accessor functions for initial GPIO configuration. I'll try to change this soon.

You are right I missed these. I will update the patch and resend. I will also fix the other esd boards in the next days.

Great, thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#4 lore raw

PATCH 1/1 ppc4xx: Cleanup PMC405 board support

In reply to Matthias Fuchs

Hi Stefan,

Quoted 14 lines · Stefan Roese
Quoted 12 lines · Matthias Fuchs
Quoted 2 lines

This patch fixes coding style for PMC405 board support. Also some unneeded features/code is removed.

Please find some comments below.

board/esd/pmc405/pmc405.c int board_early_init_f (void) · line 89

Quoted 2 lines
board/esd/pmc405/pmc405.c +2 -0
+	out32(GPIO0_TCR, CONFIG_SYS_FPGA_PRG | CONFIG_SYS_FPGA_CLK | \
+	      CONFIG_SYS_FPGA_DATA | CONFIG_SYS_XEREADY);

I suggest to switch to using the out_be32()/in_be32() accessor functions instead. I am aware that many other 4xx boards still use the "wrong" accessor functions for initial GPIO configuration. I'll try to change this soon.

Quoted 2 lines

You are right I missed these. I will update the patch and resend. I will also fix the other esd boards in the next days.

please take a look at my 2nd patch ("Update PMC405 ...."). It does the requested accessor fixes. So my first patch does nothing by style cleanup while
the 2nd one brings some updates. I tried not to mix up beautyfication with
functional code changes :-) So please keep these patches as they are :-)

Matthias

#5 lore raw

PATCH 1/1 ppc4xx: Cleanup PMC405 board support

Quoted 5 lines · Matthias Fuchs
Quoted 5 lines
Quoted 4 lines

I suggest to switch to using the out_be32()/in_be32() accessor functions instead. I am aware that many other 4xx boards still use the "wrong" accessor functions for initial GPIO configuration. I'll try to change this soon.

Quoted 8 lines
Quoted 2 lines

You are right I missed these. I will update the patch and resend. I will also fix the other esd boards in the next days.

please take a look at my 2nd patch ("Update PMC405 ...."). It does the requested accessor fixes. So my first patch does nothing by style cleanup while the 2nd one brings some updates. I tried not to mix up beautyfication with functional code changes :-) So please keep these patches as they are :-)

OK, I'll apply your patches as they are.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

Applied
#6 lore raw

PATCH 1/1 ppc4xx: Cleanup PMC405 board support

In reply to Matthias Fuchs
Quoted 2 lines · Matthias Fuchs

This patch fixes coding style for PMC405 board support. Also some unneeded features/code is removed.

Applied to ppc4xx/master. Thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#7 lore raw

PATCH 1/1 ppc4xx: Cleanup PMC405 board support

Hi Matthias,

Quoted 5 lines · Stefan Roese
Quoted 2 lines · Matthias Fuchs

This patch fixes coding style for PMC405 board support. Also some unneeded features/code is removed.

Applied to ppc4xx/master. Thanks.

After applying I noticed still some minor coding style issues in pmc405.c. I just generated a patch fixing those problems.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================