Skip to contentSkip to conversation

i.MX31: support GPIO as a chip-select in the mxc_spi driver

PATCH New Guennadi Liakhovetski 4 participants 5 messages Feb 13, 2009 – Feb 24, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v4 3/9 i.MX31: support GPIO as a chip-select in the mxc_spi driver

Some SPI devices have special requirements on chip-select handling. With this patch we can use a GPIO as a chip-select and strictly follow the SPI_XFER_BEGIN and SPI_XFER_END flags.

---

Changes since v1: long lines split, mx31_gpio_* calls now also defined if CONFIG_MX31_GPIO is not defined (see patch 2/9), '!!' removed. Changes since v2: added braces in a multiline if, switched to ARRAY_SIZE().
Changes since v3: moved GPIO chipselect initialisation into a separate function, as suggested by Wolfgang Denk

 drivers/spi/mxc_spi.c |   64 ++++++++++++++++++++++++++++++++++++++++++------
 1 files changed, 56 insertions(+), 8 deletions(-)
drivers/spi/mxc_spi.c +56 -8
index 3135817..daad1bb 100644
@@ -21,6 +21,7 @@
 #include <common.h>
 #include <malloc.h>
 #include <spi.h>
+#include <asm/errno.h>
 #include <asm/io.h>
 
 #ifdef CONFIG_MX27
@@ -32,6 +33,8 @@
 
 #else
 
+#include <asm/arch/mx31.h>
+
 #define MXC_CSPIRXDATA		0x00
 #define MXC_CSPITXDATA		0x04
 #define MXC_CSPICTRL		0x08
@@ -68,6 +71,7 @@ struct mxc_spi_slave {
 	struct spi_slave slave;
 	unsigned long	base;
 	u32		ctrl_reg;
+	int		gpio;
 };
 
 static inline struct mxc_spi_slave *to_mxc_spi_slave(struct spi_slave *slave)
@@ -85,7 +89,8 @@ static inline void reg_write(unsigned long addr, u32 val)
 	*(volatile unsigned long*)addr = val;
 }
 
-static u32 spi_xchg_single(struct spi_slave *slave, u32 data, int bitlen)
+static u32 spi_xchg_single(struct spi_slave *slave, u32 data, int bitlen,
+			   unsigned long flags)
 {
 	struct mxc_spi_slave *mxcs = to_mxc_spi_slave(slave);
 	unsigned int cfg_reg = reg_read(mxcs->base + MXC_CSPICTRL);
@@ -96,6 +101,9 @@ static u32 spi_xchg_single(struct spi_slave *slave, u32 data, int bitlen)
 	if (cfg_reg != mxcs->ctrl_reg)
 		reg_write(mxcs->base + MXC_CSPICTRL, mxcs->ctrl_reg);
 
+	if (mxcs->gpio > 0 && (flags & SPI_XFER_BEGIN))
+		mx31_gpio_set(mxcs->gpio, mxcs->ctrl_reg & MXC_CSPICTRL_SSPOL);
+
 	reg_write(mxcs->base + MXC_CSPITXDATA, data);
 
 	reg_write(mxcs->base + MXC_CSPICTRL, mxcs->ctrl_reg | MXC_CSPICTRL_XCH);
@@ -103,6 +111,11 @@ static u32 spi_xchg_single(struct spi_slave *slave, u32 data, int bitlen)
 	while (reg_read(mxcs->base + MXC_CSPICTRL) & MXC_CSPICTRL_XCH)
 		;
 
+	if (mxcs->gpio > 0 && (flags & SPI_XFER_END)) {
+		mx31_gpio_set(mxcs->gpio,
+			      !(mxcs->ctrl_reg & MXC_CSPICTRL_SSPOL));
+	}
+
 	return reg_read(mxcs->base + MXC_CSPIRXDATA);
 }
 
@@ -121,7 +134,7 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
 	for (i = 0, in_l = (u32 *)din, out_l = (u32 *)dout;
 	     i < n_blks;
 	     i++, in_l++, out_l++, bitlen -= 32) {
-		u32 data = spi_xchg_single(slave, *out_l, bitlen);
+		u32 data = spi_xchg_single(slave, *out_l, bitlen, flags);
 
 		/* Check if we're only transfering 8 or 16 bits */
 		if (!i) {
@@ -139,15 +152,54 @@ void spi_init(void)
 {
 }
 
+static int decode_cs(struct mxc_spi_slave *mxcs, unsigned int cs)
+{
+	int ret;
+
+	/*
+	 * Some SPI devices require active chip-select over multiple
+	 * transactions, we achieve this using a GPIO. Still, the SPI
+	 * controller has to be configured to use one of its own chipselects.
+	 * To use this feature you have to call spi_setup_slave() with
+	 * cs = internal_cs | (gpio << 8), and you have to use some unused
+	 * on this SPI controller cs between 0 and 3.
+	 */
+	if (cs > 3) {
+		mxcs->gpio = cs >> 8;
+		cs &= 3;
+		ret = mx31_gpio_direction(mxcs->gpio, MX31_GPIO_DIRECTION_OUT);
+		if (ret) {
+			printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio);
+			return -EINVAL;
+		}
+	} else {
+		mxcs->gpio = -1;
+	}
+
+	return cs;
+}
+
 struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
 			unsigned int max_hz, unsigned int mode)
 {
 	unsigned int ctrl_reg;
 	struct mxc_spi_slave *mxcs;
+	int ret;
+
+	if (bus >= ARRAY_SIZE(spi_bases))
+		return NULL;
+
+	mxcs = malloc(sizeof(struct mxc_spi_slave));
+	if (!mxcs)
+		return NULL;
 
-	if (bus >= sizeof(spi_bases) / sizeof(spi_bases[0]) ||
-	    cs > 3)
+	ret = decode_cs(mxcs, cs);
+	if (ret < 0) {
+		free(mxcs);
 		return NULL;
+	}
+
+	cs = ret;
 
 	ctrl_reg = MXC_CSPICTRL_CHIPSELECT(cs) |
 		MXC_CSPICTRL_BITCOUNT(31) |
@@ -162,10 +214,6 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
 	if (mode & SPI_CS_HIGH)
 		ctrl_reg |= MXC_CSPICTRL_SSPOL;
 
-	mxcs = malloc(sizeof(struct mxc_spi_slave));
-	if (!mxcs)
-		return NULL;
-
 	mxcs->slave.bus = bus;
 	mxcs->slave.cs = cs;
 	mxcs->base = spi_bases[bus];
Signature · 1 line
1.5.4
#1 lore raw

PATCH v4 3/9 i.MX31: support GPIO as a chip-select in the mxc_spi driver

Quoted 5 lines · Guennadi Liakhovetski

Some SPI devices have special requirements on chip-select handling. With this patch we can use a GPIO as a chip-select and strictly follow the SPI_XFER_BEGIN and SPI_XFER_END flags.

Quoted 8 lines

---

Changes since v1: long lines split, mx31_gpio_* calls now also defined if CONFIG_MX31_GPIO is not defined (see patch 2/9), '!!' removed. Changes since v2: added braces in a multiline if, switched to ARRAY_SIZE().
Changes since v3: moved GPIO chipselect initialisation into a separate function, as suggested by Wolfgang Denk

Evenif I do not like to only allow to use cpu GPIO as cs

With the current SPI implementation

Best Regards,
J.

#2 lore raw

PATCH v4 3/9 i.MX31: support GPIO as a chip-select in the mxc_spi driver

Dear Jean-Christophe PLAGNIOL-VILLARD,

Quoted 2 lines · In message <[email protected]> you wrote:

Why do you ACK this? Are you waiting for someone else to apply this?

It's you who is the ARM custodian, right?

Best regards,

Wolfgang Denk

Signature · 7 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
I don't mind criticism. You know me. I've  never  been  one  to  take
offence  at  criticism. No one could say I'm the sort to take offence
at criticism -- Not twice, anyway. Not without blowing bubbles.
                                  - Terry Pratchett, _Witches Abroad_
#3 lore raw

PATCH v4 3/9 i.MX31: support GPIO as a chip-select in the mxc_spi driver

Quoted 7 lines · Wolfgang Denk

Dear Jean-Christophe PLAGNIOL-VILLARD,

Quoted 2 lines · In message <[email protected]> you wrote:

Why do you ACK this? Are you waiting for someone else to apply this?

It's better to pull this whole series via one tree due to inter-dependencies, and as most diffstat is under drivers/video, we decided to pull it via the video tree, patches that are not directly video-related have to be acked by respective custodians.

Quoted 1 line

It's you who is the ARM custodian, right?

Thanks
Guennadi
---
Guennadi Liakhovetski, Ph.D.

DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de

#4 lore raw

PATCH v4 3/9 i.MX31: support GPIO as a chip-select in the mxc_spi driver

In reply to Guennadi Liakhovetski
Quoted 14 lines · Guennadi Liakhovetski

Some SPI devices have special requirements on chip-select handling. With this patch we can use a GPIO as a chip-select and strictly follow the SPI_XFER_BEGIN and SPI_XFER_END flags.

---

Changes since v1: long lines split, mx31_gpio_* calls now also defined if CONFIG_MX31_GPIO is not defined (see patch 2/9), '!!' removed. Changes since v2: added braces in a multiline if, switched to ARRAY_SIZE().
Changes since v3: moved GPIO chipselect initialisation into a separate function, as suggested by Wolfgang Denk

Quoted 3 lines
 drivers/spi/mxc_spi.c |   64

++++++++++++++++++++++++++++++++++++++++++------ 1 files changed, 56 insertions(+), 8 deletions(-)

Applied to u-boot-video/master.

Thanks,
Anatolij