Skip to contentSkip to conversation

OMAP3530 USB host problems

DISCUSSION Gary Thomas 3 participants 13 messages Feb 20, 2009 – Feb 23, 2009

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

	/* Wait for TLL to be Active */
        timeout = 1000;
	while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
			& (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
		cpu_relax();
        }

Any clues on why this might be? How do I solve it?

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#1 lore raw
Quoted 15 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

	/* Wait for TLL to be Active */
        timeout = 1000;
	while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
			& (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
		cpu_relax();
        }
Quoted 1 line

Any clues on why this might be? How do I solve it?

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

Signature · 1 line
balbi
#2 lore raw
Quoted 16 lines · Felipe Balbi
Quoted 15 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

	/* Wait for TLL to be Active */
        timeout = 1000;
	while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
			& (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
		cpu_relax();
        }
Quoted 7 lines
Quoted 1 line

Any clues on why this might be? How do I solve it?

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#3 lore raw
Quoted 21 lines · Gary Thomas
Quoted 20 lines · Felipe Balbi
Quoted 15 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

	/* Wait for TLL to be Active */
        timeout = 1000;
	while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
			& (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
		cpu_relax();
        }
Quoted 1 line

Any clues on why this might be? How do I solve it?

could you enable CONFIG_DEBUG_LL and post the seria console output ?

Quoted 7 lines
Quoted 3 lines

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

you have OMAP_EHCI_TLL_MODE set, you should probably use OMAP_EHCI_PHY_MODE instead.

You can fix it via "make menuconfig"

Signature · 1 line
balbi
#4 lore raw
Quoted 24 lines · Felipe Balbi
Quoted 23 lines · Gary Thomas
Quoted 22 lines · Felipe Balbi
Quoted 15 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

	/* Wait for TLL to be Active */
        timeout = 1000;
	while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
			& (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
		cpu_relax();
        }
Quoted 1 line

Any clues on why this might be? How do I solve it?

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

Quoted 9 lines
Quoted 3 lines

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

you have OMAP_EHCI_TLL_MODE set, you should probably use OMAP_EHCI_PHY_MODE instead.

You can fix it via "make menuconfig"

I already have that; this code is still being used.
# CONFIG_OMAP_EHCI_TLL_MODE is not set CONFIG_OMAP_EHCI_PHY_MODE=y

This is not used in the function above at all.

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#5 lore raw
Quoted 32 lines · Gary Thomas
Quoted 31 lines · Felipe Balbi
Quoted 18 lines · Gary Thomas
Quoted 17 lines · Felipe Balbi
Quoted 16 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

	/* Wait for TLL to be Active */
        timeout = 1000;
	while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
			& (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
		cpu_relax();
        }

Any clues on why this might be? How do I solve it?

Quoted 8 lines
Quoted 5 lines

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

you have OMAP_EHCI_TLL_MODE set, you should probably use OMAP_EHCI_PHY_MODE instead.

Quoted 8 lines
Quoted 2 lines

You can fix it via "make menuconfig"

I already have that; this code is still being used.
# CONFIG_OMAP_EHCI_TLL_MODE is not set CONFIG_OMAP_EHCI_PHY_MODE=y

This is not used in the function above at all.

hmm.. true, just checked the function.

Weird, TRM says when that bit is 1, we cannot access ST_USBTLL, we should access it when it's 0, try the following:

drivers/usb/host/ehci-omap.c +1 -1
index 1b3266c..122e95b 100644
@@ -250,7 +250,7 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 
        /* Wait for TLL to be Active */
        while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
-                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
+                       & (0 << OMAP3430ES2_ST_USBTLL_SHIFT)))
                cpu_relax();
 
        /* perform TLL soft reset, and wait until reset is complete */

and tell us if it worked

Signature · 1 line
balbi
#6 lore raw
Quoted 59 lines · Felipe Balbi
Quoted 31 lines · Gary Thomas
Quoted 30 lines · Felipe Balbi
Quoted 18 lines · Gary Thomas
Quoted 17 lines · Felipe Balbi
Quoted 16 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

	/* Wait for TLL to be Active */
        timeout = 1000;
	while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
			& (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
		cpu_relax();
        }

Any clues on why this might be? How do I solve it?

Quoted 8 lines
Quoted 5 lines

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

you have OMAP_EHCI_TLL_MODE set, you should probably use OMAP_EHCI_PHY_MODE instead.

Quoted 7 lines
Quoted 2 lines

You can fix it via "make menuconfig"

I already have that; this code is still being used.
# CONFIG_OMAP_EHCI_TLL_MODE is not set CONFIG_OMAP_EHCI_PHY_MODE=y

This is not used in the function above at all.

hmm.. true, just checked the function.

Weird, TRM says when that bit is 1, we cannot access ST_USBTLL, we should access it when it's 0, try the following:

drivers/usb/host/ehci-omap.c +1 -1
index 1b3266c..122e95b 100644
@@ -250,7 +250,7 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 
        /* Wait for TLL to be Active */
        while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
-                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
+                       & (0 << OMAP3430ES2_ST_USBTLL_SHIFT)))
                cpu_relax();
 
        /* perform TLL soft reset, and wait until reset is complete */
Quoted 2 lines

and tell us if it worked

Sadly, I've already tried this and things just continue to fall apart.

Unhandled fault: external abort on non-linefetch (0x1008) at 0xd8062010

  Internal error: : 1008 [#1]
  Modules linked in:
  CPU: 0    Not tainted  (2.6.27-omap1-svn4799-dirty14 #60)
  PC is at ehci_hcd_omap_drv_probe+0x370/0x5e4
  LR is at release_console_sem+0x1a8/0x1d8

Hence, my desired to figure out the TLL timeout...

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#7 lore raw
Quoted 65 lines · Gary Thomas
Quoted 59 lines · Felipe Balbi
Quoted 31 lines · Gary Thomas
Quoted 30 lines · Felipe Balbi
Quoted 18 lines · Gary Thomas
Quoted 17 lines · Felipe Balbi
Quoted 16 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

	/* Wait for TLL to be Active */
        timeout = 1000;
	while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
			& (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
		cpu_relax();
        }

Any clues on why this might be? How do I solve it?

Quoted 8 lines
Quoted 5 lines

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

you have OMAP_EHCI_TLL_MODE set, you should probably use OMAP_EHCI_PHY_MODE instead.

Quoted 7 lines
Quoted 2 lines

You can fix it via "make menuconfig"

I already have that; this code is still being used.
# CONFIG_OMAP_EHCI_TLL_MODE is not set CONFIG_OMAP_EHCI_PHY_MODE=y

This is not used in the function above at all.

hmm.. true, just checked the function.

Weird, TRM says when that bit is 1, we cannot access ST_USBTLL, we should access it when it's 0, try the following:

drivers/usb/host/ehci-omap.c +1 -1
index 1b3266c..122e95b 100644
@@ -250,7 +250,7 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 
        /* Wait for TLL to be Active */
        while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
-                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
+                       & (0 << OMAP3430ES2_ST_USBTLL_SHIFT)))
                cpu_relax();
 
        /* perform TLL soft reset, and wait until reset is complete */
Quoted 2 lines

and tell us if it worked

Sadly, I've already tried this and things just continue to fall apart.

Quoted 8 lines

Unhandled fault: external abort on non-linefetch (0x1008) at 0xd8062010

  Internal error: : 1008 [#1]
  Modules linked in:
  CPU: 0    Not tainted  (2.6.27-omap1-svn4799-dirty14 #60)
  PC is at ehci_hcd_omap_drv_probe+0x370/0x5e4
  LR is at release_console_sem+0x1a8/0x1d8

Hence, my desired to figure out the TLL timeout...

keep TLL as is, the problem now seems to be a clock that should be on and is off. Try to figure (with printk() for example) at which line the code stops, put printk() before and after register read/write operations during probe and omap_start_ehc(), let's see where does it dies.

Signature · 1 line
balbi
#8 lore raw
Quoted 73 lines · ext Felipe Balbi
Quoted 72 lines · Gary Thomas
Quoted 59 lines · Felipe Balbi
Quoted 31 lines · Gary Thomas
Quoted 30 lines · Felipe Balbi
Quoted 18 lines · Gary Thomas
Quoted 17 lines · Felipe Balbi
Quoted 16 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

       /* Wait for TLL to be Active */
        timeout = 1000;
       while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
               cpu_relax();
        }

Any clues on why this might be? How do I solve it?

Quoted 8 lines
Quoted 5 lines

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

you have OMAP_EHCI_TLL_MODE set, you should probably use OMAP_EHCI_PHY_MODE instead.

Quoted 7 lines
Quoted 2 lines

You can fix it via "make menuconfig"

I already have that; this code is still being used.
# CONFIG_OMAP_EHCI_TLL_MODE is not set CONFIG_OMAP_EHCI_PHY_MODE=y

This is not used in the function above at all.

hmm.. true, just checked the function.

Weird, TRM says when that bit is 1, we cannot access ST_USBTLL, we should access it when it's 0, try the following:

drivers/usb/host/ehci-omap.c +1 -1
index 1b3266c..122e95b 100644
@@ -250,7 +250,7 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 
        /* Wait for TLL to be Active */
        while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
-                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
+                       & (0 << OMAP3430ES2_ST_USBTLL_SHIFT)))
                cpu_relax();
 
        /* perform TLL soft reset, and wait until reset is complete */
Quoted 2 lines

and tell us if it worked

Sadly, I've already tried this and things just continue to fall apart.

Unhandled fault: external abort on non-linefetch (0x1008) at 0xd8062010

  Internal error: : 1008 [#1]
  Modules linked in:
  CPU: 0    Not tainted  (2.6.27-omap1-svn4799-dirty14 #60)
  PC is at ehci_hcd_omap_drv_probe+0x370/0x5e4
  LR is at release_console_sem+0x1a8/0x1d8
Quoted 6 lines
Quoted 1 line

Hence, my desired to figure out the TLL timeout...

keep TLL as is, the problem now seems to be a clock that should be on and is off. Try to figure (with printk() for example) at which line the code stops, put printk() before and after register read/write operations during probe and omap_start_ehc(), let's see where does it dies.

any news ??

Signature · 1 line
balbi
#9 lore raw
Quoted 72 lines · Felipe Balbi
Quoted 71 lines · ext Felipe Balbi
Quoted 70 lines · Gary Thomas
Quoted 58 lines · Felipe Balbi
Quoted 31 lines · Gary Thomas
Quoted 30 lines · Felipe Balbi
Quoted 18 lines · Gary Thomas
Quoted 17 lines · Felipe Balbi
Quoted 16 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

       /* Wait for TLL to be Active */
        timeout = 1000;
       while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
               cpu_relax();
        }

Any clues on why this might be? How do I solve it?

Quoted 8 lines
Quoted 5 lines

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

you have OMAP_EHCI_TLL_MODE set, you should probably use OMAP_EHCI_PHY_MODE instead.

Quoted 7 lines
Quoted 2 lines

You can fix it via "make menuconfig"

I already have that; this code is still being used.
# CONFIG_OMAP_EHCI_TLL_MODE is not set CONFIG_OMAP_EHCI_PHY_MODE=y

This is not used in the function above at all.

hmm.. true, just checked the function.

Weird, TRM says when that bit is 1, we cannot access ST_USBTLL, we should access it when it's 0, try the following:

drivers/usb/host/ehci-omap.c +1 -1
index 1b3266c..122e95b 100644
@@ -250,7 +250,7 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 
        /* Wait for TLL to be Active */
        while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
-                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
+                       & (0 << OMAP3430ES2_ST_USBTLL_SHIFT)))
                cpu_relax();
 
        /* perform TLL soft reset, and wait until reset is complete */
Quoted 2 lines

and tell us if it worked

Sadly, I've already tried this and things just continue to fall apart.

Unhandled fault: external abort on non-linefetch (0x1008) at 0xd8062010

  Internal error: : 1008 [#1]
  Modules linked in:
  CPU: 0    Not tainted  (2.6.27-omap1-svn4799-dirty14 #60)
  PC is at ehci_hcd_omap_drv_probe+0x370/0x5e4
  LR is at release_console_sem+0x1a8/0x1d8
Quoted 8 lines
Quoted 5 lines
Quoted 1 line

Hence, my desired to figure out the TLL timeout...

keep TLL as is, the problem now seems to be a clock that should be on and is off. Try to figure (with printk() for example) at which line the code stops, put printk() before and after register read/write operations during probe and omap_start_ehc(), let's see where does it dies.

any news ??

Not really; I'd like to figure out *why* this part of the USB device isn't working, not just find a way around it...

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#10 lore raw
Quoted 79 lines · ext Gary Thomas
Quoted 78 lines · Felipe Balbi
Quoted 76 lines · ext Felipe Balbi
Quoted 63 lines · Gary Thomas
Quoted 58 lines · Felipe Balbi
Quoted 31 lines · Gary Thomas
Quoted 30 lines · Felipe Balbi
Quoted 18 lines · Gary Thomas
Quoted 17 lines · Felipe Balbi
Quoted 16 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

       /* Wait for TLL to be Active */
        timeout = 1000;
       while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
               cpu_relax();
        }

Any clues on why this might be? How do I solve it?

Quoted 8 lines
Quoted 5 lines

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

you have OMAP_EHCI_TLL_MODE set, you should probably use OMAP_EHCI_PHY_MODE instead.

Quoted 7 lines
Quoted 2 lines

You can fix it via "make menuconfig"

I already have that; this code is still being used.
# CONFIG_OMAP_EHCI_TLL_MODE is not set CONFIG_OMAP_EHCI_PHY_MODE=y

This is not used in the function above at all.

hmm.. true, just checked the function.

Weird, TRM says when that bit is 1, we cannot access ST_USBTLL, we should access it when it's 0, try the following:

drivers/usb/host/ehci-omap.c +1 -1
index 1b3266c..122e95b 100644
@@ -250,7 +250,7 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 
        /* Wait for TLL to be Active */
        while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
-                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
+                       & (0 << OMAP3430ES2_ST_USBTLL_SHIFT)))
                cpu_relax();
 
        /* perform TLL soft reset, and wait until reset is complete */
Quoted 2 lines

and tell us if it worked

Sadly, I've already tried this and things just continue to fall apart.

Quoted 8 lines

Unhandled fault: external abort on non-linefetch (0x1008) at 0xd8062010

  Internal error: : 1008 [#1]
  Modules linked in:
  CPU: 0    Not tainted  (2.6.27-omap1-svn4799-dirty14 #60)
  PC is at ehci_hcd_omap_drv_probe+0x370/0x5e4
  LR is at release_console_sem+0x1a8/0x1d8

Hence, my desired to figure out the TLL timeout...

keep TLL as is, the problem now seems to be a clock that should be on and is off. Try to figure (with printk() for example) at which line the code stops, put printk() before and after register read/write operations during probe and omap_start_ehc(), let's see where does it dies.

Quoted 5 lines
Quoted 2 lines

any news ??

Not really; I'd like to figure out *why* this part of the USB device isn't working, not just find a way around it...

It's not a way around it. That bit is wrong, one problem is fixed now but we came to another issue which is a non-linefetch, which makes me wonder that's a clock issue.

You should just try to fetch me for information and I might be able to help you more.

Signature · 1 line
balbi
#11 lore raw
Quoted 84 lines · Felipe Balbi
Quoted 74 lines · ext Gary Thomas
Quoted 73 lines · Felipe Balbi
Quoted 72 lines · ext Felipe Balbi
Quoted 71 lines · Gary Thomas
Quoted 58 lines · Felipe Balbi
Quoted 31 lines · Gary Thomas
Quoted 30 lines · Felipe Balbi
Quoted 18 lines · Gary Thomas
Quoted 17 lines · Felipe Balbi
Quoted 16 lines · Gary Thomas

I have a 3530 board (similar to the OMAP3EVM) and I'm trying to get the USB host working. Sadly, this is failing, but I don't quite see why. From drivers/usb/host/echi-omap.c:

       /* Wait for TLL to be Active */
        timeout = 1000;
       while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
        {
            if (--timeout <= 0) {
                printk(KERN_ERR "USB TLL is unavailable\n");
                return -ENODEV;
            }
               cpu_relax();
        }

Any clues on why this might be? How do I solve it?

Quoted 8 lines
Quoted 5 lines

could you enable CONFIG_DEBUG_LL and post the seria console output ?

do you really use TLL ?? I don't really know omap3evm, but I guess it uses PHY mode (correct me if I'm wrong).

It's not that I _need_ TLL, the driver function omap_start_ehci() tries to reset the part of the USB controller and fails. I'm just trying to understand why this part of the code falls over.

you have OMAP_EHCI_TLL_MODE set, you should probably use OMAP_EHCI_PHY_MODE instead.

Quoted 7 lines
Quoted 2 lines

You can fix it via "make menuconfig"

I already have that; this code is still being used.
# CONFIG_OMAP_EHCI_TLL_MODE is not set CONFIG_OMAP_EHCI_PHY_MODE=y

This is not used in the function above at all.

hmm.. true, just checked the function.

Weird, TRM says when that bit is 1, we cannot access ST_USBTLL, we should access it when it's 0, try the following:

drivers/usb/host/ehci-omap.c +1 -1
index 1b3266c..122e95b 100644
@@ -250,7 +250,7 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 
        /* Wait for TLL to be Active */
        while ((cm_read_mod_reg(CORE_MOD, OMAP2430_CM_IDLEST3)
-                       & (1 << OMAP3430ES2_ST_USBTLL_SHIFT)))
+                       & (0 << OMAP3430ES2_ST_USBTLL_SHIFT)))
                cpu_relax();
 
        /* perform TLL soft reset, and wait until reset is complete */
Quoted 2 lines

and tell us if it worked

Sadly, I've already tried this and things just continue to fall apart.

Unhandled fault: external abort on non-linefetch (0x1008) at 0xd8062010

  Internal error: : 1008 [#1]
  Modules linked in:
  CPU: 0    Not tainted  (2.6.27-omap1-svn4799-dirty14 #60)
  PC is at ehci_hcd_omap_drv_probe+0x370/0x5e4
  LR is at release_console_sem+0x1a8/0x1d8

Hence, my desired to figure out the TLL timeout...

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines

keep TLL as is, the problem now seems to be a clock that should be on and is off. Try to figure (with printk() for example) at which line the code stops, put printk() before and after register read/write operations during probe and omap_start_ehc(), let's see where does it dies.

any news ??

Not really; I'd like to figure out *why* this part of the USB device isn't working, not just find a way around it...

Quoted 7 lines

It's not a way around it. That bit is wrong, one problem is fixed now but we came to another issue which is a non-linefetch, which makes me wonder that's a clock issue.

You should just try to fetch me for information and I might be able to help you more.

It turns out that the various USB clocks were not enabled (this is prototype hardware, only roughly equivalent to the OMAP3EVM and I started with a kernel snapshot more than a month ago, so much may have changed in the meantime). I can now get through this part of the USB host initialization code (still doesn't work, but I think I can figure it out).

Thanks for the pointers

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#12 lore raw
Quoted 5 lines · Gary Thomas

It turns out that the various USB clocks were not enabled (this is prototype hardware, only roughly equivalent to the OMAP3EVM and I started with a kernel snapshot more than a month ago, so much may have changed in the meantime). I can now get through this part of the USB host initialization code (still doesn't work, but I think I can figure it out).

Yeah, as I suspected. Even in current linux-omap, I got report that vbus goes on, but enumeration doesn't happen, so you're at the same stage.

Quoted 1 line

Thanks for the pointers

no problems

Signature · 1 line
balbi