Skip to contentSkip to conversation

2.6.28 - 2.6.29-rc6-git5 regression, p4-clockmod/cpufreq probably

DISCUSSION Denys Fedoryschenko 4 participants 8 messages Mar 2, 2009 ACPI

lore
Share & tools
lore
#0 lore raw

Please CC me, i am not on linux-kernel maillist

Hardware: Asus EEE 702,
CPU: Intel Celeron 900 Mhz

On 2.6.28 p4-clockmod available, and i can manage governor, frequency and etc over cpufrequtils.
On 2.6.29-rc6 (git5 tested also) also shown in dmesg as available, but i can't change anything.

root # cpufreq-info
cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006 Report errors and bugs to [email protected], please. analyzing CPU 0:
no or unknown cpufreq driver is active on this CPU

There is no noticeable differences in dmesg.
Both have

[    2.438474] p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation 

available

Here is end of strace on cpufreq-info lstat64("/sys/devices/system/cpu/cpu0/", {st_mode=S_IFDIR|0755, st_size=0, ...}) = 0
lstat64("/sys/devices/system/cpu/cpu0/", {st_mode=S_IFDIR|0755, st_size=0, ...}) = 0
write(1, "analyzing CPU 0:\n"..., 17analyzing CPU 0:
) = 17
stat64("/sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq", 0xbfbce570) = -1 ENOENT (No such file or directory) open("/proc/sys/cpu/0/speed", O_RDONLY) = -1 ENOENT (No such file or directory) stat64("/sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq", 0xbfbce570) = -1 ENOENT (No such file or directory) stat64("/sys/devices/system/cpu/cpu0/cpufreq/scaling_driver", 0xbfbce580) = -1 ENOENT (No such file or directory)
write(1, " no or unknown cpufreq driver is"..., 53 no or unknown cpufreq driver is active on this CPU
) = 53 stat64("/sys/devices/system/cpu/cpu0/cpufreq/affected_cpus", 0xbfbce460) = -1 ENOENT (No such file or directory) stat64("/sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_min_freq", 0xbfbce560) = -1 ENOENT (No such file or directory) stat64("/sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies", 0xbfbce460) = -1 ENOENT (No such file or directory) stat64("/sys/devices/system/cpu/cpu0/cpufreq/scaling_available_governors", 0xbfbce560) = -1 ENOENT (No such file or directory) stat64("/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor", 0xbfbce570) = -1 ENOENT (No such file or directory)

If you need more information, let me know.

#1 lore raw
Quoted 2 lines · Denys Fedoryschenko

On 2.6.29-rc6 (git5 tested also) also shown in dmesg as available, but i can't change anything.

That's deliberate. p4-clockmod is for thermal management, not clock control (since it doesn't actually do any of that)

Signature · 1 line
Matthew Garrett | [email protected]
#2 lore raw
Quoted 6 lines · On Monday 02 March 2009 18:06:59 Matthew Garrett wrote:
Quoted 2 lines · Denys Fedoryschenko

On 2.6.29-rc6 (git5 tested also) also shown in dmesg as available, but i can't change anything.

That's deliberate. p4-clockmod is for thermal management, not clock control (since it doesn't actually do any of that)

I know very well it is just throttling, and not real CPU power management. At the end it does job.

In my case i used it for testing on "virtual" 113 Mhz video encoding to find out bottleneck on ffmpeg and to compare performance with Blackfin.

In another case it helps me to limit current from battery(i have custom power supply solution), so battery will lasts longer (on spikes, if it uses full CPU power at 900 Mhz, voltage dropping (specially on last "drops of battery life), and protection unit disconnecting laptop. Throttling helping to prevent this.

Actually i am not asking if it nice or not, just if there is feature which is not working.

#3 lore raw
Quoted 5 lines · Denys Fedoryschenko
Quoted 4 lines · On Monday 02 March 2009 18:06:59 Matthew Garrett wrote:
Quoted 2 lines · Denys Fedoryschenko

On 2.6.29-rc6 (git5 tested also) also shown in dmesg as available, but i can't change anything.

Quoted 7 lines
Quoted 2 lines

That's deliberate. p4-clockmod is for thermal management, not clock control (since it doesn't actually do any of that)

I know very well it is just throttling, and not real CPU power management. At the end it does job.

In my case i used it for testing on "virtual" 113 Mhz video encoding to find out bottleneck on ffmpeg and to compare performance with Blackfin.

If it's just throttling you want can't you do that via /proc/acpi/processor/CPU<N>/throttling ...

Signature · 1 line
Sitsofe | http://sucs.org/~sits/
#4 lore raw
Quoted 9 lines · On Monday 02 March 2009 18:26:21 Sitsofe Wheeler wrote:
Quoted 8 lines · Denys Fedoryschenko
Quoted 6 lines · On Monday 02 March 2009 18:06:59 Matthew Garrett wrote:
Quoted 2 lines · Denys Fedoryschenko

On 2.6.29-rc6 (git5 tested also) also shown in dmesg as available, but i can't change anything.

That's deliberate. p4-clockmod is for thermal management, not clock control (since it doesn't actually do any of that)

Quoted 8 lines
Quoted 5 lines

I know very well it is just throttling, and not real CPU power management. At the end it does job.

In my case i used it for testing on "virtual" 113 Mhz video encoding to find out bottleneck on ffmpeg and to compare performance with Blackfin.

If it's just throttling you want can't you do that via /proc/acpi/processor/CPU<N>/throttling ...

CPUFreq infrastructure much more powerful.
-d --min <FREQ>
new minimum CPU frequency the governor may select.
-u --max <FREQ>
new maximum CPU frequency the governor may select.
-g --governor <GOV>
new cpufreq governor.

This things you cannot do over inserting values over ACPI. Sure you can reinvent the wheel, but why?

#5 lore raw
Quoted 10 lines · Denys Fedoryschenko

CPUFreq infrastructure much more powerful.

(quoted diff) +0 -3
-d --min <FREQ>
    new minimum CPU frequency the governor may select. 
-u --max <FREQ>
    new maximum CPU frequency the governor may select. 
-g --governor <GOV>
    new cpufreq governor. 

This things you cannot do over inserting values over ACPI. Sure you can reinvent the wheel, but why?

I guess I don't understand why you would want scaling if it didn't save you any power...

Signature · 1 line
Sitsofe | http://sucs.org/~sits/
#6 lore raw
Quoted 9 lines · On Monday 02 March 2009 19:23:09 Sitsofe Wheeler wrote:
Quoted 8 lines · Denys Fedoryschenko

CPUFreq infrastructure much more powerful.

(quoted diff) +0 -3
-d --min <FREQ>
    new minimum CPU frequency the governor may select.
-u --max <FREQ>
    new maximum CPU frequency the governor may select.
-g --governor <GOV>
    new cpufreq governor.
Quoted 5 lines
Quoted 2 lines

This things you cannot do over inserting values over ACPI. Sure you can reinvent the wheel, but why?

I guess I don't understand why you would want scaling if it didn't save you any power...

If i will limit current in certain limits, rather than using high current, i will have in result higher efficiency of discharging battery.
The discharge curves for a Lithium Ion cell below show that the effective capacity of the cell is reduced if the cell is discharged at very high rates (or conversely increased with low discharge rates). This is called the capacity offset and the effect is common to most cell chemistries. If the discharge takes place over a long period of several hours as with some high rate applications such as electric vehicles, the effective capacity of the battery can be as much as double the specified capacity at the C rate. This can be most important when dimensioning an expensive battery for high power use. The capacity of low power, consumer electronics batteries is normally specified for discharge at the C rate whereas the SAE uses the discharge over a period of 20 hours (0.05C) as the standard condition for measuring the Amphour capacity of automotive batteries. The graph below shows that the effective capacity of a deep discharge lead acid battery is almost doubled as the discharge rate is reduced from 1.0C to 0.05C. For discharge times less than one hour (High C rates) the effective capacity falls off dramatically.
This means even i need to recode on battery movie (clearly need same amount of processing power), if i do it with 100% CPU available let's say in 30 minutes, and if i do it with 50% CPU available in 60 minutes, at the end i should have DIFFERENT amount of remaining battery.

Another example, if i run screensaver i want governor powersave(so some crazy flash plugin don't dry out battery till i come back) , if i run on battery i will put conservative and limit frequency range to max 50% of CPU power, so i can be sure my laptop lasts enough time. This in case battery time matter for me more than computing power. Sure i will prefer some universal way, so i can set same rules on Core 2 Duo based laptop, and cheap Celeron. Cpufreq provide me useful framework for this job, and important SAME API everywhere. Less efficient on p4-clockmod, and very efficient on true "mobile" processors.

* Many things quoted from http://www.mpoweruk.com/performance.htm

#7 lore raw
Quoted 47 lines · Denys Fedoryschenko
Quoted 9 lines · On Monday 02 March 2009 19:23:09 Sitsofe Wheeler wrote:
Quoted 8 lines · Denys Fedoryschenko

CPUFreq infrastructure much more powerful.

(quoted diff) +0 -3
-d --min <FREQ>
    new minimum CPU frequency the governor may select.
-u --max <FREQ>
    new maximum CPU frequency the governor may select.
-g --governor <GOV>
    new cpufreq governor.
Quoted 5 lines
Quoted 2 lines

This things you cannot do over inserting values over ACPI. Sure you can reinvent the wheel, but why?

I guess I don't understand why you would want scaling if it didn't save you any power...

If i will limit current in certain limits, rather than using high current, i will have in result higher efficiency of discharging battery.
The discharge curves for a Lithium Ion cell below show that the effective capacity of the cell is reduced if the cell is discharged at very high rates (or conversely increased with low discharge rates). This is called the capacity offset and the effect is common to most cell chemistries. If the discharge takes place over a long period of several hours as with some high rate applications such as electric vehicles, the effective capacity of the battery can be as much as double the specified capacity at the C rate. This can be most important when dimensioning an expensive battery for high power use. The capacity of low power, consumer electronics batteries is normally specified for discharge at the C rate whereas the SAE uses the discharge over a period of 20 hours (0.05C) as the standard condition for measuring the Amphour capacity of automotive batteries. The graph below shows that the effective capacity of a deep discharge lead acid battery is almost doubled as the discharge rate is reduced from 1.0C to 0.05C. For discharge times less than one hour (High C rates) the effective capacity falls off dramatically.
This means even i need to recode on battery movie (clearly need same amount of processing power), if i do it with 100% CPU available let's say in 30 minutes, and if i do it with 50% CPU available in 60 minutes, at the end i should have DIFFERENT amount of remaining battery.

Another example, if i run screensaver i want governor powersave(so some crazy flash plugin don't dry out battery till i come back) , if i run on battery i will put conservative and limit frequency range to max 50% of CPU power, so i can be sure my laptop lasts enough time. This in case battery time matter for me more than computing power. Sure i will prefer some universal way, so i can set same rules on Core 2 Duo based laptop, and cheap Celeron. Cpufreq provide me useful framework for this job, and important SAME API everywhere. Less efficient on p4-clockmod, and very efficient on true "mobile" processors.

Quoted 1 line

* Many things quoted from http://www.mpoweruk.com/performance.htm

You should have added linux-acpi to the CC list and since the change in question was very much on purpose, I'm not going to list (at least for now).

Thanks,
Rafael