Skip to contentSkip to conversation

ide: add support for CFA specified transfer modes (take 2)

PATCH In review Sergei Shtylyov 2 participants 4 messages Mar 7, 2009 – Mar 8, 2009 libata

lore
Share & tools
lore
#0 lore raw

PATCH 2/2 ide: add support for CFA specified transfer modes (take 2)

Add support for the CompactFlash specific PIO modes 5/6 and MWDMA modes 3/4.

---
Did two changes after Bart's review:
- fixed wrong mask in ide_config_drive_speed();
- clarified comment in ide_pio_cycle_time().

This patch is against the current pata-2.6 series. Since there were no PIO5 capable hard drives produced and you also need 66 MHz input clock to actually get the difference WRT the setup timing programmed, I decided to simply replace the old non-standard PIO mode 5 timings with CFA specified ones. Phew, hopefully I haven't overlooked anything -- quite a lot had to be changed.

Stanislaw, please give it a try -- I don't have any CF hardware now.

 drivers/ide/ide-dma.c       |    8 ++++++++
 drivers/ide/ide-iops.c      |    8 ++++++++
 drivers/ide/ide-timings.c   |   12 ++++++++++--
 drivers/ide/ide-xfer-mode.c |   15 +++++++++------
 4 files changed, 35 insertions(+), 8 deletions(-)
drivers/ide/ide-dma.c +8 -0
Index: linux-2.6/drivers/ide/ide-dma.c
===================================================================
@@ -261,6 +261,14 @@ static unsigned int ide_get_mode_mask(id
 		break;
 	case XFER_MW_DMA_0:
 		mask = id[ATA_ID_MWDMA_MODES];
+
+		/* Also look for the CF specific MWDMA modes... */
+		if (ata_id_is_cfa(id) && (id[ATA_ID_CFA_MODES] & 0x38)) {
+			u8 mode = ((id[ATA_ID_CFA_MODES] & 0x38) >> 3) - 1;
+
+			mask |= ((2 << mode) - 1) << 3;
+		}
+
 		if (port_ops && port_ops->mdma_filter)
 			mask &= port_ops->mdma_filter(drive);
 		else
drivers/ide/ide-iops.c +8 -0
Index: linux-2.6/drivers/ide/ide-iops.c
===================================================================
@@ -389,6 +389,8 @@ int ide_config_drive_speed(ide_drive_t *
 	id[ATA_ID_UDMA_MODES]  &= ~0xFF00;
 	id[ATA_ID_MWDMA_MODES] &= ~0x0F00;
 	id[ATA_ID_SWDMA_MODES] &= ~0x0F00;
+	if (ata_id_is_cfa(id))
+		id[ATA_ID_CFA_MODES] &= ~0x0FC0;
 
  skip:
 #ifdef CONFIG_BLK_DEV_IDEDMA
@@ -401,12 +403,18 @@ int ide_config_drive_speed(ide_drive_t *
 	if (speed >= XFER_UDMA_0) {
 		i = 1 << (speed - XFER_UDMA_0);
 		id[ATA_ID_UDMA_MODES] |= (i << 8 | i);
+	} else if (ata_id_is_cfa(id) && speed >= XFER_MW_DMA_3) {
+		i = speed - XFER_MW_DMA_2;
+		id[ATA_ID_CFA_MODES] |= i << 9;
 	} else if (speed >= XFER_MW_DMA_0) {
 		i = 1 << (speed - XFER_MW_DMA_0);
 		id[ATA_ID_MWDMA_MODES] |= (i << 8 | i);
 	} else if (speed >= XFER_SW_DMA_0) {
 		i = 1 << (speed - XFER_SW_DMA_0);
 		id[ATA_ID_SWDMA_MODES] |= (i << 8 | i);
+	} else if (ata_id_is_cfa(id) && speed >= XFER_PIO_5) {
+		i = speed - XFER_PIO_4;
+		id[ATA_ID_CFA_MODES] |= i << 6;
 	}
 
 	if (!drive->init_speed)
drivers/ide/ide-timings.c +10 -2
Index: linux-2.6/drivers/ide/ide-timings.c
===================================================================
@@ -43,6 +43,8 @@ static struct ide_timing ide_timing[] = 
 	{ XFER_UDMA_1,     0,   0,   0,   0,   0,   0,   0,  80 },
 	{ XFER_UDMA_0,     0,   0,   0,   0,   0,   0,   0, 120 },
 
+	{ XFER_MW_DMA_4,  25,   0,   0,   0,  55,  20,  80,   0 },
+	{ XFER_MW_DMA_3,  25,   0,   0,   0,  65,  25, 100,   0 },
 	{ XFER_MW_DMA_2,  25,   0,   0,   0,  70,  25, 120,   0 },
 	{ XFER_MW_DMA_1,  45,   0,   0,   0,  80,  50, 150,   0 },
 	{ XFER_MW_DMA_0,  60,   0,   0,   0, 215, 215, 480,   0 },
@@ -51,7 +53,8 @@ static struct ide_timing ide_timing[] = 
 	{ XFER_SW_DMA_1,  90,   0,   0,   0, 240, 240, 480,   0 },
 	{ XFER_SW_DMA_0, 120,   0,   0,   0, 480, 480, 960,   0 },
 
-	{ XFER_PIO_5,     20,  50,  30, 100,  50,  30, 100,   0 },
+	{ XFER_PIO_6,     10,  55,  20,  80,  55,  20,  80,   0 },
+	{ XFER_PIO_5,     15,  65,  25, 100,  65,  25, 100,   0 },
 	{ XFER_PIO_4,     25,  70,  25, 120,  70,  25, 120,   0 },
 	{ XFER_PIO_3,     30,  80,  70, 180,  80,  70, 180,   0 },
 
@@ -90,6 +93,10 @@ u16 ide_pio_cycle_time(ide_drive_t *driv
 		/* conservative "downgrade" for all pre-ATA2 drives */
 		if (pio < 3 && cycle < t->cycle)
 			cycle = 0; /* use standard timing */
+
+		/* Use the standard timing for the CF specific modes too */
+		if (pio > 4 && ata_id_is_cfa(id))
+			cycle = 0;
 	}
 
 	return cycle ? cycle : t->cycle;
@@ -161,7 +168,8 @@ int ide_timing_compute(ide_drive_t *driv
 
 		if (speed <= XFER_PIO_2)
 			p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO];
-		else if (speed <= XFER_PIO_5)
+		else if ((speed <= XFER_PIO_4) ||
+			 (speed == XFER_PIO_5 && !ata_id_is_cfa(id)))
 			p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY];
 		else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
 			p.cycle = id[ATA_ID_EIDE_DMA_MIN];
drivers/ide/ide-xfer-mode.c +9 -6
Index: linux-2.6/drivers/ide/ide-xfer-mode.c
===================================================================
@@ -9,11 +9,11 @@ static const char *udma_str[] =
 	 { "UDMA/16", "UDMA/25",  "UDMA/33",  "UDMA/44",
 	   "UDMA/66", "UDMA/100", "UDMA/133", "UDMA7" };
 static const char *mwdma_str[] =
-	{ "MWDMA0", "MWDMA1", "MWDMA2" };
+	{ "MWDMA0", "MWDMA1", "MWDMA2", "MWDMA3", "MWDMA4" };
 static const char *swdma_str[] =
 	{ "SWDMA0", "SWDMA1", "SWDMA2" };
 static const char *pio_str[] =
-	{ "PIO0", "PIO1", "PIO2", "PIO3", "PIO4", "PIO5" };
+	{ "PIO0", "PIO1", "PIO2", "PIO3", "PIO4", "PIO5", "PIO6" };
 
 /**
  *	ide_xfer_verbose	-	return IDE mode names
@@ -30,11 +30,11 @@ const char *ide_xfer_verbose(u8 mode)
 
 	if (mode >= XFER_UDMA_0 && mode <= XFER_UDMA_7)
 		s = udma_str[i];
-	else if (mode >= XFER_MW_DMA_0 && mode <= XFER_MW_DMA_2)
+	else if (mode >= XFER_MW_DMA_0 && mode <= XFER_MW_DMA_4)
 		s = mwdma_str[i];
 	else if (mode >= XFER_SW_DMA_0 && mode <= XFER_SW_DMA_2)
 		s = swdma_str[i];
-	else if (mode >= XFER_PIO_0 && mode <= XFER_PIO_5)
+	else if (mode >= XFER_PIO_0 && mode <= XFER_PIO_6)
 		s = pio_str[i & 0x7];
 	else if (mode == XFER_PIO_SLOW)
 		s = "PIO SLOW";
@@ -79,7 +79,10 @@ u8 ide_get_best_pio_mode(ide_drive_t *dr
 		}
 
 		if (id[ATA_ID_FIELD_VALID] & 2) {	      /* ATA2? */
-			if (ata_id_has_iordy(id)) {
+			if (ata_id_is_cfa(id) && (id[ATA_ID_CFA_MODES] & 7))
+				pio_mode = 4 + min_t(int, 2,
+						     id[ATA_ID_CFA_MODES] & 7);
+			else if (ata_id_has_iordy(id)) {
 				if (id[ATA_ID_PIO_MODES] & 7) {
 					overridden = 0;
 					if (id[ATA_ID_PIO_MODES] & 4)
@@ -239,7 +242,7 @@ int ide_set_xfer_rate(ide_drive_t *drive
 
 	BUG_ON(rate < XFER_PIO_0);
 
-	if (rate >= XFER_PIO_0 && rate <= XFER_PIO_5)
+	if (rate >= XFER_PIO_0 && rate <= XFER_PIO_6)
 		return ide_set_pio_mode(drive, rate);
 
 	return ide_set_dma_mode(drive, rate);
#1 lore raw
Quoted 17 lines · Hello, I wrote:

Add support for the CompactFlash specific PIO modes 5/6 and MWDMA modes 3/4.

---
Did two changes after Bart's review:
- fixed wrong mask in ide_config_drive_speed();
- clarified comment in ide_pio_cycle_time().

This patch is against the current pata-2.6 series. Since there were no PIO5 capable hard drives produced and you also need 66 MHz input clock to actually get the difference WRT the setup timing programmed, I decided to simply replace the old non-standard PIO mode 5 timings with CFA specified ones. Phew, hopefully I haven't overlooked anything -- quite a lot had to be changed.

Stanislaw, please give it a try -- I don't have any CF hardware now.

[...]

drivers/ide/ide-iops.c int ide_config_drive_speed(ide_drive_t * · line 394

Quoted 11 lines

Index: linux-2.6/drivers/ide/ide-iops.c
===================================================================

drivers/ide/ide-iops.c +2 -0
@@ -389,6 +389,8 @@ int ide_config_drive_speed(ide_drive_t *
 	id[ATA_ID_UDMA_MODES]  &= ~0xFF00;
 	id[ATA_ID_MWDMA_MODES] &= ~0x0F00;
 	id[ATA_ID_SWDMA_MODES] &= ~0x0F00;
+	if (ata_id_is_cfa(id))
+		id[ATA_ID_CFA_MODES] &= ~0x0FC0;
 

Oops, won't this fragment clear the current DMA mode when setting PIO
mode (and so vice versa for CF)?

MBR, Sergei

#2 lore raw
Quoted 20 lines · Sergei Shtylyov
Quoted 17 lines · Hello, I wrote:

Add support for the CompactFlash specific PIO modes 5/6 and MWDMA modes 3/4.

---
Did two changes after Bart's review:
- fixed wrong mask in ide_config_drive_speed();
- clarified comment in ide_pio_cycle_time().

This patch is against the current pata-2.6 series. Since there were no PIO5 capable hard drives produced and you also need 66 MHz input clock to actually get the difference WRT the setup timing programmed, I decided to simply replace the old non-standard PIO mode 5 timings with CFA specified ones. Phew, hopefully I haven't overlooked anything -- quite a lot had to be changed.

Stanislaw, please give it a try -- I don't have any CF hardware now.

[...]

Quoted 14 lines

drivers/ide/ide-iops.c int ide_config_drive_speed(ide_drive_t * · line 394

Quoted 11 lines

Index: linux-2.6/drivers/ide/ide-iops.c
===================================================================

drivers/ide/ide-iops.c +2 -0
@@ -389,6 +389,8 @@ int ide_config_drive_speed(ide_drive_t *
 	id[ATA_ID_UDMA_MODES]  &= ~0xFF00;
 	id[ATA_ID_MWDMA_MODES] &= ~0x0F00;
 	id[ATA_ID_SWDMA_MODES] &= ~0x0F00;
+	if (ata_id_is_cfa(id))
+		id[ATA_ID_CFA_MODES] &= ~0x0FC0;
 

Oops, won't this fragment clear the current DMA mode when setting PIO
mode (and so vice versa for CF)?

Indeed, however since we never check selected modes later (except ide_id_dma_bug() but its intent is to check for buggy devices) there is no much point in all these id hacks and this seems to be the perfect opportunity to just remove them.

Thanks,
Bart

#3 lore raw

Hello.

Quoted 36 lines · Bartlomiej Zolnierkiewicz
Quoted 20 lines
Quoted 18 lines

Add support for the CompactFlash specific PIO modes 5/6 and MWDMA modes 3/4.

---
Did two changes after Bart's review:
- fixed wrong mask in ide_config_drive_speed();
- clarified comment in ide_pio_cycle_time().

This patch is against the current pata-2.6 series. Since there were no PIO5 capable hard drives produced and you also need 66 MHz input clock to actually get the difference WRT the setup timing programmed, I decided to simply replace the old non-standard PIO mode 5 timings with CFA specified ones. Phew, hopefully I haven't overlooked anything -- quite a lot had to be changed.

Stanislaw, please give it a try -- I don't have any CF hardware now.

[...]

Quoted 15 lines

drivers/ide/ide-iops.c int ide_config_drive_speed(ide_drive_t * · line 395

Quoted 12 lines

Index: linux-2.6/drivers/ide/ide-iops.c
===================================================================

drivers/ide/ide-iops.c +2 -0
@@ -389,6 +389,8 @@ int ide_config_drive_speed(ide_drive_t *
 	id[ATA_ID_UDMA_MODES]  &= ~0xFF00;
 	id[ATA_ID_MWDMA_MODES] &= ~0x0F00;
 	id[ATA_ID_SWDMA_MODES] &= ~0x0F00;
+	if (ata_id_is_cfa(id))
+		id[ATA_ID_CFA_MODES] &= ~0x0FC0;
 
 

Oops, won't this fragment clear the current DMA mode when setting PIO
mode (and so vice versa for CF)?

Quoted 5 lines

Indeed, however since we never check selected modes later (except ide_id_dma_bug() but its intent is to check for buggy devices) there is no much point in all these id hacks and this seems to be the perfect opportunity to just remove them.

Doesn't this serve for e.g. presenting the current identify data via
procfs? I've been already considering fixing this...

Quoted 3 lines

Thanks,
Bart

MBR, Sergei