Skip to contentSkip to conversation

sh: SuperH Mobile suspend support

PATCH In review Magnus Damm 2 participants 7 messages Mar 9, 2009 – Mar 16, 2009

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 sh: SuperH Mobile suspend support

From: Magnus Damm <[email protected]>

This patch adds CONFIG_SUSPEND support to the SuperH architecture. If enabled, SuperH Mobile processors will register their suspend callbacks during boot.

To suspend, use "echo mem > /sys/power/state". To allow wakeup, make sure "/sys/device/platform/../power/wakeup" contains "enabled". Additional per-device driver patches are most likely needed.

---

 arch/sh/Kconfig                           |    1 
 arch/sh/include/asm/suspend.h             |   12 ++
 arch/sh/kernel/cpu/sh4a/Makefile          |    7 +
 arch/sh/kernel/cpu/sh4a/pm-sh_mobile.c    |   76 +++++++++++++++++
 arch/sh/kernel/cpu/sh4a/sleep-sh_mobile.S |  125 +++++++++++++++++++++++++++++
 5 files changed, 221 insertions(+)
arch/sh/Kconfig +1 -0
@@ -159,6 +159,7 @@ config CPU_SH4
 	select CPU_HAS_SR_RB
 	select CPU_HAS_PTEA if !CPU_SH4A || CPU_SHX2
 	select CPU_HAS_FPU if !CPU_SH4AL_DSP
+	select ARCH_SUSPEND_POSSIBLE
 
 config CPU_SH4A
 	bool
arch/sh/include/asm/suspend.h +12 -0
@@ -1,6 +1,7 @@
 #ifndef _ASM_SH_SUSPEND_H
 #define _ASM_SH_SUSPEND_H
 
+#ifndef __ASSEMBLY__
 static inline int arch_prepare_suspend(void) { return 0; }
 
 #include <asm/ptrace.h>
@@ -9,5 +10,16 @@ struct swsusp_arch_regs {
 	struct pt_regs user_regs;
 	unsigned long bank1_regs[8];
 };
+#endif
+
+#define SUSP_SH_SLEEP		(1 << 0) /* Regular sleep mode */
+#define SUSP_SH_STANDBY		(1 << 1) /* Software standby mode */
+#define SUSP_SH_RSTANDBY	(1 << 2) /* R-standby mode */
+#define SUSP_SH_USTANDBY	(1 << 3) /* U-standby mode */
+#define SUSP_SH_SF		(1 << 4) /* Enable self-refresh */
+
+#define SUSP_MODE_SLEEP		(SUSP_SH_SLEEP)
+#define SUSP_MODE_SLEEP_SF	(SUSP_SH_SLEEP | SUSP_SH_SF)
+#define SUSP_MODE_STANDBY_SF	(SUSP_SH_STANDBY | SUSP_SH_SF)
 
 #endif /* _ASM_SH_SUSPEND_H */
arch/sh/kernel/cpu/sh4a/Makefile +7 -0
@@ -35,6 +35,13 @@ pinmux-$(CONFIG_CPU_SUBTYPE_SH7723)	:= p
 pinmux-$(CONFIG_CPU_SUBTYPE_SH7785)	:= pinmux-sh7785.o
 pinmux-$(CONFIG_CPU_SUBTYPE_SH7786)	:= pinmux-sh7786.o
 
+# Power Mangement & Sleep mode
+pm-$(CONFIG_CPU_SUBTYPE_SH7343)		:= pm-sh_mobile.o sleep-sh_mobile.o
+pm-$(CONFIG_CPU_SUBTYPE_SH7366)		:= pm-sh_mobile.o sleep-sh_mobile.o
+pm-$(CONFIG_CPU_SUBTYPE_SH7722)		:= pm-sh_mobile.o sleep-sh_mobile.o
+pm-$(CONFIG_CPU_SUBTYPE_SH7723)		:= pm-sh_mobile.o sleep-sh_mobile.o
+
 obj-y			+= $(clock-y)
 obj-$(CONFIG_SMP)	+= $(smp-y)
 obj-$(CONFIG_GENERIC_GPIO)	+= $(pinmux-y)
+obj-$(CONFIG_PM)	+= $(pm-y)
arch/sh/kernel/cpu/sh4a/pm-sh_mobile.c new file +76 -0

76 lines not on this page · raw message

arch/sh/kernel/cpu/sh4a/sleep-sh_mobile.S new file +125 -0

125 lines not on this page · raw message

#1 lore raw

arch/sh/Kconfig config CPU_SH4 · line 165

Quoted 10 lines · Magnus Damm
arch/sh/Kconfig +1 -0
@@ -159,6 +159,7 @@ config CPU_SH4
 	select CPU_HAS_SR_RB
 	select CPU_HAS_PTEA if !CPU_SH4A || CPU_SHX2
 	select CPU_HAS_FPU if !CPU_SH4AL_DSP
+	select ARCH_SUSPEND_POSSIBLE
 
 config CPU_SH4A
 	bool

This is bogus, as this is all SH-Mobile specific. The easiest option is probably to define a CPU_SHMOBILE that all of these CPUs can select, and then moving all of this in to arch/sh/kernel/cpu/shmobile/. We've done similar things on the ARM side for code-sharing between SH-Mobile G3 and G4 for example.

Quoted 12 lines
arch/sh/include/asm/suspend.h +1 -0
@@ -1,6 +1,7 @@
 #ifndef _ASM_SH_SUSPEND_H
 #define _ASM_SH_SUSPEND_H
 
+#ifndef __ASSEMBLY__
 static inline int arch_prepare_suspend(void) { return 0; }
 
 #include <asm/ptrace.h>
@@ -9,5 +10,16 @@ struct swsusp_arch_regs {
 	struct pt_regs user_regs;

arch/sh/include/asm/suspend.h struct swsusp_arch_regs { · line 20

Quoted 10 lines
arch/sh/include/asm/suspend.h +8 -0
 	unsigned long bank1_regs[8];
 };
+#endif
+
+#define SUSP_SH_SLEEP		(1 << 0) /* Regular sleep mode */
+#define SUSP_SH_STANDBY		(1 << 1) /* Software standby mode */
+#define SUSP_SH_RSTANDBY	(1 << 2) /* R-standby mode */
+#define SUSP_SH_USTANDBY	(1 << 3) /* U-standby mode */
+#define SUSP_SH_SF		(1 << 4) /* Enable self-refresh */
+

This probably wants a bit more explanation, as it's not entirely obvious for folks not familiar with SH-Mobile internals what standby modes are generic SH vs SH-Mobile specific.

arch/sh/include/asm/suspend.h struct swsusp_arch_regs { · line 23

Quoted 3 lines
arch/sh/include/asm/suspend.h +3 -0
+extern const unsigned char do_standby[];
+extern const unsigned int do_standby_size;
+

These are pretty uninspired globals, please use something more definitive. (ie, shmobile_enter_standby/shmobile_standby_size or something similar).

arch/sh/include/asm/suspend.h struct swsusp_arch_regs {

Quoted 8 lines
arch/sh/include/asm/suspend.h +8 -0
+static void set_vbr(void *base)
+{
+	asm volatile("ldc	%0, vbr"
+		     : /* no output */
+		     : "r" (base)
+		     : "memory");
+}
+

Just toss this in an asm/ header somewhere, it's not worth reimplementing all over the place. Although for a single instruction it doesn't really add much, you may as well just open-code it.

#2 lore raw

PATCH 1/1 sh: SuperH Mobile suspend support V2

In reply to Magnus Damm

From: Magnus Damm <[email protected]>

This patch contains CONFIG_SUSPEND support to the SuperH architecture V2. If enabled, SuperH Mobile processors will register their suspend callbacks during boot.

To suspend, use "echo mem > /sys/power/state". To allow wakeup, make sure "/sys/device/platform/../power/wakeup" contains "enabled". Additional per-device driver patches are most likely needed.

---

Changes since V1:
- fixed up issues pointed out by Paul
- added more comments

 arch/sh/Kconfig                           |    1 
 arch/sh/include/asm/suspend.h             |    9 ++
 arch/sh/kernel/cpu/sh4a/Makefile          |    7 +
 arch/sh/kernel/cpu/sh4a/pm-sh_mobile.c    |   92 +++++++++++++++++++++
 arch/sh/kernel/cpu/sh4a/sleep-sh_mobile.S |  125 +++++++++++++++++++++++++++++
 5 files changed, 234 insertions(+)
arch/sh/Kconfig +1 -0
@@ -181,6 +181,7 @@ config CPU_SHX3
 
 config ARCH_SHMOBILE
 	bool
+	select ARCH_SUSPEND_POSSIBLE
 
 choice
 	prompt "Processor sub-type selection"
arch/sh/include/asm/suspend.h +9 -0
@@ -1,6 +1,7 @@
 #ifndef _ASM_SH_SUSPEND_H
 #define _ASM_SH_SUSPEND_H
 
+#ifndef __ASSEMBLY__
 static inline int arch_prepare_suspend(void) { return 0; }
 
 #include <asm/ptrace.h>
@@ -9,5 +10,13 @@ struct swsusp_arch_regs {
 	struct pt_regs user_regs;
 	unsigned long bank1_regs[8];
 };
+#endif
+
+/* flags passed to assembly suspend code */
+#define SUSP_SH_SLEEP		(1 << 0) /* Regular sleep mode */
+#define SUSP_SH_STANDBY		(1 << 1) /* SH-Mobile Software standby mode */
+#define SUSP_SH_RSTANDBY	(1 << 2) /* SH-Mobile R-standby mode */
+#define SUSP_SH_USTANDBY	(1 << 3) /* SH-Mobile U-standby mode */
+#define SUSP_SH_SF		(1 << 4) /* Enable self-refresh */
 
 #endif /* _ASM_SH_SUSPEND_H */
arch/sh/kernel/cpu/sh4a/Makefile +7 -0
@@ -35,6 +35,13 @@ pinmux-$(CONFIG_CPU_SUBTYPE_SH7723)	:= p
 pinmux-$(CONFIG_CPU_SUBTYPE_SH7785)	:= pinmux-sh7785.o
 pinmux-$(CONFIG_CPU_SUBTYPE_SH7786)	:= pinmux-sh7786.o
 
+# Power Mangement & Sleep mode
+pm-$(CONFIG_CPU_SUBTYPE_SH7343)		:= pm-sh_mobile.o sleep-sh_mobile.o
+pm-$(CONFIG_CPU_SUBTYPE_SH7366)		:= pm-sh_mobile.o sleep-sh_mobile.o
+pm-$(CONFIG_CPU_SUBTYPE_SH7722)		:= pm-sh_mobile.o sleep-sh_mobile.o
+pm-$(CONFIG_CPU_SUBTYPE_SH7723)		:= pm-sh_mobile.o sleep-sh_mobile.o
+
 obj-y			+= $(clock-y)
 obj-$(CONFIG_SMP)	+= $(smp-y)
 obj-$(CONFIG_GENERIC_GPIO)	+= $(pinmux-y)
+obj-$(CONFIG_PM)	+= $(pm-y)
arch/sh/kernel/cpu/sh4a/pm-sh_mobile.c new file +92 -0

92 lines not on this page · raw message

arch/sh/kernel/cpu/sh4a/sleep-sh_mobile.S new file +125 -0

125 lines not on this page · raw message

#3 lore raw

PATCH 1/1 sh: SuperH Mobile suspend support V3

In reply to Magnus Damm

From: Magnus Damm <[email protected]>

This patch contains CONFIG_SUSPEND support to the SuperH architecture V3. If enabled, SuperH Mobile processors will register their suspend callbacks during boot.

To suspend, use "echo mem > /sys/power/state". To allow wakeup, make sure "/sys/device/platform/../power/wakeup" contains "enabled". Additional per-device driver patches are most likely needed.

---

Changes since V2:
- fixed ILRAM typo
- use CONFIG_ARCH_SHMOBILE in Makefile

Changes since V1:
- fixed up issues pointed out by Paul
- added more comments

 arch/sh/Kconfig                           |    1 
 arch/sh/include/asm/suspend.h             |    9 ++
 arch/sh/kernel/cpu/sh4a/Makefile          |    4 
 arch/sh/kernel/cpu/sh4a/pm-sh_mobile.c    |   92 +++++++++++++++++++++
 arch/sh/kernel/cpu/sh4a/sleep-sh_mobile.S |  125 +++++++++++++++++++++++++++++
 5 files changed, 231 insertions(+)
arch/sh/Kconfig +1 -0
@@ -181,6 +181,7 @@ config CPU_SHX3
 
 config ARCH_SHMOBILE
 	bool
+	select ARCH_SUSPEND_POSSIBLE
 
 choice
 	prompt "Processor sub-type selection"
arch/sh/include/asm/suspend.h +9 -0
@@ -1,6 +1,7 @@
 #ifndef _ASM_SH_SUSPEND_H
 #define _ASM_SH_SUSPEND_H
 
+#ifndef __ASSEMBLY__
 static inline int arch_prepare_suspend(void) { return 0; }
 
 #include <asm/ptrace.h>
@@ -9,5 +10,13 @@ struct swsusp_arch_regs {
 	struct pt_regs user_regs;
 	unsigned long bank1_regs[8];
 };
+#endif
+
+/* flags passed to assembly suspend code */
+#define SUSP_SH_SLEEP		(1 << 0) /* Regular sleep mode */
+#define SUSP_SH_STANDBY		(1 << 1) /* SH-Mobile Software standby mode */
+#define SUSP_SH_RSTANDBY	(1 << 2) /* SH-Mobile R-standby mode */
+#define SUSP_SH_USTANDBY	(1 << 3) /* SH-Mobile U-standby mode */
+#define SUSP_SH_SF		(1 << 4) /* Enable self-refresh */
 
 #endif /* _ASM_SH_SUSPEND_H */
arch/sh/kernel/cpu/sh4a/Makefile +4 -0
@@ -35,6 +35,10 @@ pinmux-$(CONFIG_CPU_SUBTYPE_SH7723)	:= p
 pinmux-$(CONFIG_CPU_SUBTYPE_SH7785)	:= pinmux-sh7785.o
 pinmux-$(CONFIG_CPU_SUBTYPE_SH7786)	:= pinmux-sh7786.o
 
+# Power Mangement & Sleep mode
+pm-$(CONFIG_ARCH_SHMOBILE)		:= pm-sh_mobile.o sleep-sh_mobile.o
+
 obj-y			+= $(clock-y)
 obj-$(CONFIG_SMP)	+= $(smp-y)
 obj-$(CONFIG_GENERIC_GPIO)	+= $(pinmux-y)
+obj-$(CONFIG_PM)	+= $(pm-y)
arch/sh/kernel/cpu/sh4a/pm-sh_mobile.c new file +92 -0

92 lines not on this page · raw message

arch/sh/kernel/cpu/sh4a/sleep-sh_mobile.S new file +125 -0

125 lines not on this page · raw message

#4 lore raw

PATCH 1/1 sh: add ap325 lcd power off support

From: Magnus Damm <[email protected]>

Improve the ap325 board code to allow the lcd panel and backlight to be powered off.

---

 arch/sh/boards/board-ap325rxa.c |   11 +++++++++++
 1 file changed, 11 insertions(+)
arch/sh/boards/board-ap325rxa.c +11 -0
@@ -166,6 +166,16 @@ static void ap320_wvga_power_on(void *bo
 	ctrl_outw(0x100, FPGA_BKLREG);
 }
 
+static void ap320_wvga_power_off(void *board_data)
+{
+	/* backlight */
+	ctrl_outw(0, FPGA_BKLREG);
+	gpio_set_value(GPIO_PTS3, 1);
+
+	/* ASD AP-320/325 LCD OFF */
+	ctrl_outw(0, FPGA_LCDREG);
+}
+
 static struct sh_mobile_lcdc_info lcdc_info = {
 	.clock_source = LCDC_CLK_EXTERNAL,
 	.ch[0] = {
@@ -191,6 +201,7 @@ static struct sh_mobile_lcdc_info lcdc_i
 		},
 		.board_cfg = {
 			.display_on = ap320_wvga_power_on,
+			.display_off = ap320_wvga_power_off,
 		},
 	}
 };
#5 lore raw

PATCH 1/1 video: sh_mobile_lcdcfb suspend/resume support

From: Magnus Damm <[email protected]>

This patch adds suspend/resume support to the LCDC driver for SuperH Mobile - sh_mobile_lcdcfb.

We simply stop hardware on suspend and start it again on resume. For RGB panels this is trivial, but for SYS panels in deferred io mode this becomes a bit more difficult - we need to wait for a frame end interrupt to make sure the clocks are balanced before stopping the actual hardware.

---

Tested on ap325 and Migo-R.

 drivers/video/sh_mobile_lcdcfb.c |   66 +++++++++++++++++++++++++++++++++-----
 1 file changed, 59 insertions(+), 7 deletions(-)
drivers/video/sh_mobile_lcdcfb.c +59 -7
@@ -33,6 +33,8 @@ struct sh_mobile_lcdc_chan {
 	struct fb_info info;
 	dma_addr_t dma_handle;
 	struct fb_deferred_io defio;
+	unsigned long frame_end;
+	wait_queue_head_t frame_end_wait;
 };
 
 struct sh_mobile_lcdc_priv {
@@ -226,7 +228,10 @@ static void sh_mobile_lcdc_deferred_io_t
 static irqreturn_t sh_mobile_lcdc_irq(int irq, void *data)
 {
 	struct sh_mobile_lcdc_priv *priv = data;
+	struct sh_mobile_lcdc_chan *ch;
 	unsigned long tmp;
+	int is_sub;
+	int k;
 
 	/* acknowledge interrupt */
 	tmp = lcdc_read(priv, _LDINTR);
@@ -234,8 +239,24 @@ static irqreturn_t sh_mobile_lcdc_irq(in
 	tmp |= 0x000000ff ^ LDINTR_FS; /* status in low 8 */
 	lcdc_write(priv, _LDINTR, tmp);
 
-	/* disable clocks */
-	sh_mobile_lcdc_clk_off(priv);
+	/* figure out if this interrupt is for main or sub lcd */
+	is_sub = (lcdc_read(priv, _LDSR) & (1 << 10)) ? 1 : 0;
+
+	/* wake up channel and disable clocks*/
+	for (k = 0; k < ARRAY_SIZE(priv->ch); k++) {
+		ch = &priv->ch[k];
+
+		if (!ch->enabled)
+			continue;
+
+		if (is_sub == lcdc_chan_is_sublcd(ch)) {
+			ch->frame_end = 1;
+			wake_up(&ch->frame_end_wait);
+
+			sh_mobile_lcdc_clk_off(priv);
+		}
+	}
+
 	return IRQ_HANDLED;
 }
 
@@ -448,18 +469,27 @@ static void sh_mobile_lcdc_stop(struct s
 	struct sh_mobile_lcdc_board_cfg	*board_cfg;
 	int k;
 
-	/* tell the board code to disable the panel */
+	/* clean up deferred io and ask board code to disable panel */
 	for (k = 0; k < ARRAY_SIZE(priv->ch); k++) {
 		ch = &priv->ch[k];
-		board_cfg = &ch->cfg.board_cfg;
-		if (board_cfg->display_off)
-			board_cfg->display_off(board_cfg->board_data);
 
-		/* cleanup deferred io if enabled */
+		/* deferred io mode:
+		 * flush frame, and wait for frame end interrupt
+		 * clean up deferred io and enable clock
+		 */
 		if (ch->info.fbdefio) {
+			ch->frame_end = 0;
+			schedule_delayed_work(&ch->info.deferred_work, 0);
+			wait_event(ch->frame_end_wait, ch->frame_end);
 			fb_deferred_io_cleanup(&ch->info);
 			ch->info.fbdefio = NULL;
+			sh_mobile_lcdc_clk_on(priv);
 		}
+
+		board_cfg = &ch->cfg.board_cfg;
+		if (board_cfg->display_off)
+			board_cfg->display_off(board_cfg->board_data);
+
 	}
 
 	/* stop the lcdc */
@@ -652,6 +682,26 @@ static int sh_mobile_lcdc_set_bpp(struct
 	return 0;
 }
 
+static int sh_mobile_lcdc_suspend(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+
+	sh_mobile_lcdc_stop(platform_get_drvdata(pdev));
+	return 0;
+}
+
+static int sh_mobile_lcdc_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+
+	return sh_mobile_lcdc_start(platform_get_drvdata(pdev));
+}
+
+static struct dev_pm_ops sh_mobile_lcdc_dev_pm_ops = {
+	.suspend = sh_mobile_lcdc_suspend,
+	.resume = sh_mobile_lcdc_resume,
+};
+
 static int sh_mobile_lcdc_remove(struct platform_device *pdev);
 
 static int __init sh_mobile_lcdc_probe(struct platform_device *pdev)
@@ -707,6 +757,7 @@ static int __init sh_mobile_lcdc_probe(s
 			dev_err(&pdev->dev, "unsupported interface type\n");
 			goto err1;
 		}
+		init_waitqueue_head(&priv->ch[i].frame_end_wait);
 
 		switch (pdata->ch[i].chan) {
 		case LCDC_CHAN_MAINLCD:
@@ -860,6 +911,7 @@ static struct platform_driver sh_mobile_
 	.driver		= {
 		.name		= "sh_mobile_lcdc_fb",
 		.owner		= THIS_MODULE,
+		.pm		= &sh_mobile_lcdc_dev_pm_ops,
 	},
 	.probe		= sh_mobile_lcdc_probe,
 	.remove		= sh_mobile_lcdc_remove,
#6 lore raw

Re: [PATCH] sh: SuperH Mobile suspend support V3

Quoted 10 lines · Magnus Damm

This patch contains CONFIG_SUSPEND support to the SuperH architecture V3. If enabled, SuperH Mobile processors will register their suspend callbacks during boot.

To suspend, use "echo mem > /sys/power/state". To allow wakeup, make sure "/sys/device/platform/../power/wakeup" contains "enabled". Additional per-device driver patches are most likely needed.

Quoted 4 lines · Magnus Damm

Improve the ap325 board code to allow the lcd panel and backlight to be powered off.

Quoted 11 lines · Magnus Damm

This patch adds suspend/resume support to the LCDC driver for SuperH Mobile - sh_mobile_lcdcfb.

We simply stop hardware on suspend and start it again on resume. For RGB panels this is trivial, but for SYS panels in deferred io mode this becomes a bit more difficult - we need to wait for a frame end interrupt to make sure the clocks are balanced before stopping the actual hardware.

All applied, thanks.