Skip to contentSkip to conversation

Remove nowhere used symbol CONFIG_SYS_CLKS_IN_HZ

PATCH New Ladislav Michl 1 participant 1 message Mar 23, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Remove nowhere used symbol CONFIG_SYS_CLKS_IN_HZ

Compile tested using 'MAKEALL arm' shown few errors, but none related to this patch. I'll address them in separate patches.

include/configs/ADNPESC1.h +0 -1
index 0977bee..b8afc17 100644
@@ -44,7 +44,6 @@
 #define	CONFIG_ADNPESC1		1		/* SSV ADNP/ESC1 board	*/
 #define CONFIG_SYS_CLK_FREQ	CONFIG_SYS_NIOS_CPU_CLK/* 50 MHz core clock	*/
 #define	CONFIG_SYS_HZ			1000		/* 1 msec time tick	*/
-#undef  CONFIG_SYS_CLKS_IN_HZ
 #define	CONFIG_BOARD_EARLY_INIT_F 1	/* enable early board-spec. init*/
 
 /*------------------------------------------------------------------------
include/configs/B2.h +0 -2
index c77ea1f..340b847 100644
@@ -116,8 +116,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x0C400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0C800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x0c700000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ				1000		/* 1 kHz */
include/configs/DK1C20.h +0 -1
index db9c17d..45ff2f7 100644
@@ -50,7 +50,6 @@
 #define	CONFIG_DK1C20		1		/* Cyclone DK-1C20 board*/
 #define CONFIG_SYS_CLK_FREQ	CONFIG_SYS_NIOS_CPU_CLK/* 50 MHz core clock	*/
 #define	CONFIG_SYS_HZ			1000		/* 1 msec time tick	*/
-#undef  CONFIG_SYS_CLKS_IN_HZ
 #define	CONFIG_BOARD_EARLY_INIT_F 1	/* enable early board-spec. init*/
 
 /*------------------------------------------------------------------------
include/configs/DK1S10.h +0 -1
index 3bd270c..ae567a3 100644
@@ -48,7 +48,6 @@
 #define	CONFIG_DK1S10		1		/* Stratix DK-1S10 board*/
 #define CONFIG_SYS_CLK_FREQ	CONFIG_SYS_NIOS_CPU_CLK/* 50 MHz core clock	*/
 #define	CONFIG_SYS_HZ			1000		/* 1 msec time tick	*/
-#undef  CONFIG_SYS_CLKS_IN_HZ
 #define	CONFIG_BOARD_EARLY_INIT_F 1	/* enable early board-spec. init*/
 
 /*------------------------------------------------------------------------
include/configs/EXBITGEN.h +0 -2
index 1dd6e57..4729464 100644
@@ -129,8 +129,6 @@
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
-#define CONFIG_SYS_CLKS_IN_HZ		1	/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
 #define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
 
include/configs/SMN42.h +0 -2
index 45e6a58..d6f41f9 100644
@@ -139,8 +139,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x81800000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x83000000	/* 24 MB in SRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x81000000	/* default load address	*/
 						/* for uClinux img is here*/
 
include/configs/SX1.h +0 -2
index 78c5152..ebc8236 100644
@@ -133,8 +133,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x10000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x12000000	/* 32 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0x10000000	/* default load address */
 
 /* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
include/configs/VCMA9.h +0 -3
index d9bcf6b..8550223 100644
@@ -172,9 +172,6 @@
 #define CONFIG_SYS_ALT_MEMTEST
 #define	CONFIG_SYS_LOAD_ADDR		0x30800000	/* default load address	*/
 
-
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 /* we configure PWM Timer 4 to 1us ~ 1MHz */
 /*#define	CONFIG_SYS_HZ			1000000 */
 #define	CONFIG_SYS_HZ			1562500
include/configs/W7OLMC.h +0 -2
index 51d0a0a..ceef76e 100644
@@ -131,8 +131,6 @@
 /* The following table includes the supported baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE	{9600}
 
-#define CONFIG_SYS_CLKS_IN_HZ		1		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address		*/
 #define CONFIG_SYS_EXTBDINFO		1		/* use extended board_info (bd_t) */
 
include/configs/W7OLMG.h +0 -2
index ca1a9d4..11e0630 100644
@@ -139,8 +139,6 @@
 /* The following table includes the supported baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE	{9600}
 
-#define CONFIG_SYS_CLKS_IN_HZ		1		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address		*/
 #define CONFIG_SYS_EXTBDINFO		1		/* use extended board_info (bd_t) */
 
include/configs/actux1.h +0 -2
index adbc399..91f6ff0 100644
@@ -95,8 +95,6 @@
 #define CONFIG_SYS_MEMTEST_START		0x00400000
 #define CONFIG_SYS_MEMTEST_END			0x00800000
 
-/* everything, incl board info, in Hz */
-#undef  CONFIG_SYS_CLKS_IN_HZ
 /* spec says 66.666 MHz, but it appears to be 33 */
 #define CONFIG_SYS_HZ				3333333
 
include/configs/actux2.h +0 -2
index 4c579eb..b936938 100644
@@ -86,8 +86,6 @@
 #define CONFIG_SYS_MEMTEST_START		0x00400000
 #define CONFIG_SYS_MEMTEST_END			0x00800000
 
-/* everything, incl board info, in Hz */
-#undef  CONFIG_SYS_CLKS_IN_HZ
 /* spec says 66.666 MHz, but it appears to be 33 */
 #define CONFIG_SYS_HZ				3333333
 
include/configs/actux3.h +0 -2
index 694f522..f5ee899 100644
@@ -84,8 +84,6 @@
 #define CONFIG_SYS_MEMTEST_START		0x00400000
 #define CONFIG_SYS_MEMTEST_END			0x00800000
 
-/* everything, incl board info, in Hz */
-#undef  CONFIG_SYS_CLKS_IN_HZ
 /* spec says 66.666 MHz, but it appears to be 33 */
 #define CONFIG_SYS_HZ				3333333
 
include/configs/actux4.h +0 -2
index cdc9956..8d70a26 100644
@@ -83,8 +83,6 @@
 #define CONFIG_SYS_MEMTEST_START		0x00400000
 #define CONFIG_SYS_MEMTEST_END			0x00800000
 
-/* everything, incl board info, in Hz */
-#undef  CONFIG_SYS_CLKS_IN_HZ
 /* spec says 66.666 MHz, but it appears to be 33 */
 #define CONFIG_SYS_HZ				3333333
 
include/configs/apollon.h +0 -1
index f83dd9c..97c8806 100644
@@ -196,7 +196,6 @@
 #define	CONFIG_SYS_MEMTEST_START	(OMAP2420_SDRC_CS0)
 #define	CONFIG_SYS_MEMTEST_END		(OMAP2420_SDRC_CS0+SZ_31M)
 
-#undef	CONFIG_SYS_CLKS_IN_HZ	/* everything, incl board info, in Hz */
 /* default load address */
 #define	CONFIG_SYS_LOAD_ADDR	(OMAP2420_SDRC_CS0)
 
include/configs/armadillo.h +0 -2
index 5a4ceaf..ef6ce22 100644
@@ -105,8 +105,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xc0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x00040000	/* default load address	for armadillo: kernel img is here*/
 
 #define	CONFIG_SYS_HZ			2000		/* decrementer freq: 2 kHz */
include/configs/assabet.h +0 -2
index 024fa20..4da68b3 100644
@@ -105,8 +105,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0400000	/* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END		0xc0800000	/* 4 ... 8 MB in DRAM   */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ
-
 #define CONFIG_SYS_LOAD_ADDR		0xc0000000	/* default load address */
 
 #define CONFIG_SYS_HZ			3686400	/* incrementer freq: 3.6864 MHz */
include/configs/cerf250.h +0 -2
index f19374e..751e03c 100644
@@ -113,8 +113,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ
-
 #define CONFIG_SYS_LOAD_ADDR		0xa2000000	/* default load address */
 
 #define CONFIG_SYS_HZ			1000
include/configs/cm4008.h +0 -2
index ce36a24..124fad7 100644
@@ -93,8 +93,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x00800000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x01000000	/* 16 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0x00008000	/* default load address */
 
 #define CONFIG_SYS_HZ			(1000)		/* 1ms resolution ticks */
include/configs/cm41xx.h +0 -2
index 02cb1ef..5c255ce 100644
@@ -93,8 +93,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x00800000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x01000000	/* 16 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0x00008000	/* default load address */
 
 #define CONFIG_SYS_HZ			(1000)		/* 1ms resolution ticks */
include/configs/cradle.h +0 -2
index 5131175..850d93b 100644
@@ -99,8 +99,6 @@
 #define CONFIG_SYS_MEMTEST_START       0xa0400000      /* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END         0xa0800000      /* 4 ... 8 MB in DRAM   */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR           0xa2000000      /* default load address */
 
 #define CONFIG_SYS_HZ			1000
include/configs/csb226.h +0 -2
index d65c14a..d9f85f0 100644
@@ -124,8 +124,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000      /* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END         0xa0800000      /* 4 ... 8 MB in DRAM   */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR           0xa3000000	/* default load address */
 						/* RS: where is this documented? */
 						/* RS: is this where U-Boot is  */
include/configs/csb272.h +0 -1
index 5d3b09a..204aea0 100644
@@ -140,7 +140,6 @@
 #define CONFIG_SYS_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM */
 
 #define	CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks	*/
-#define CONFIG_SYS_CLKS_IN_HZ		1	/* everything, incl board info, in Hz */
 #define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_info (bd_t) */
 #define CONFIG_SYS_LOAD_ADDR		0x100000 /* default load address */
 
include/configs/csb472.h +0 -1
index a33efde..9b3a11c 100644
@@ -139,7 +139,6 @@
 #define CONFIG_SYS_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM */
 
 #define	CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks	*/
-#define CONFIG_SYS_CLKS_IN_HZ		1	/* everything, incl board info, in Hz */
 #define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_info (bd_t) */
 #define CONFIG_SYS_LOAD_ADDR		0x100000 /* default load address */
 
include/configs/delta.h +0 -2
index 001b48a..f5508b7 100644
@@ -166,8 +166,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x80400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x80800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */
 
 #define CONFIG_SYS_HZ			1000
include/configs/dnp1110.h +0 -2
index e329fd3..3f658a7 100644
@@ -109,8 +109,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xc0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0xc0200000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			3686400		/* incrementer freq: 3.6864 MHz */
include/configs/eNET.h +0 -2
index 84e1aef..f7e6608 100644
@@ -116,8 +116,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x01000000	/* 1 ... 16 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			1024		/* incrementer freq: 1kHz */
include/configs/ep7312.h +0 -2
index 322a3ca..d12b13f 100644
@@ -107,8 +107,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xc0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0xc0500000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			2000		/* decrementer freq: 2 kHz */
include/configs/evb4510.h +0 -2
index cbaae62..ffc9408 100644
@@ -122,8 +122,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x00780000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0x00000000	/* default load address */
 
 #define CONFIG_SYS_SYS_CLK_FREQ	50000000	/* CPU freq: 50 MHz */
include/configs/gcplus.h +0 -2
index c0b3ab9..81ee05f 100644
@@ -118,8 +118,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xc0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0xc0000000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			3686400		/* incrementer freq: 3.6864 MHz */
include/configs/hymod.h +0 -2
index 2dacfb6..284672b 100644
@@ -271,8 +271,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x00400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x03c00000	/* 4 ... 60 MB in DRAM	*/
 
-#define CONFIG_SYS_CLKS_IN_HZ		1	/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/
include/configs/impa7.h +0 -2
index a3d023f..efd4214 100644
@@ -106,8 +106,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xc0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0xc1000000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			2000		/* decrementer freq: 2 kHz */
include/configs/innokom.h +0 -2
index 043ae2f..895998a 100644
@@ -115,8 +115,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000      /* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END         0xa0800000      /* 4 ... 8 MB in DRAM   */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR           0xa3000000      /* load kernel to this address   */
 
 #define CONFIG_SYS_HZ			1000
include/configs/integratorap.h +0 -1
index 6ce3b4d..9231e64 100644
@@ -102,7 +102,6 @@
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
 #define CONFIG_SYS_LOAD_ADDR	0x7fc0	/* default load address */
 
 /*-----------------------------------------------------------------------
include/configs/integratorcp.h +0 -1
index 5b4747a..b4219d0 100644
@@ -121,7 +121,6 @@ SIB at Block62 End Block62 address 0x24f80000
 #define CONFIG_SYS_MAXARGS	16			/* max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE		/* Boot Argument Buffer Size*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
 #define CONFIG_SYS_LOAD_ADDR	0x7fc0	/* default load address */
 
 /*-----------------------------------------------------------------------
include/configs/ixdp425.h +0 -2
index 70f3987..768e836 100644
@@ -104,8 +104,6 @@
 #define CONFIG_SYS_MEMTEST_START       0x00400000      /* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END         0x00800000      /* 4 ... 8 MB in DRAM   */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR           0x00010000      /* default load address */
 
 #define CONFIG_SYS_HZ                  3333333         /* spec says 66.666 MHz, but it appears to be 33 */
include/configs/ixdpg425.h +0 -1
index 193008e..75707e5 100644
@@ -115,7 +115,6 @@
 #define CONFIG_SYS_MEMTEST_END         0x00800000      /* 4 ... 8 MB in DRAM   */
 #define CONFIG_SYS_LOAD_ADDR           0x00010000      /* default load address */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
 #define CONFIG_SYS_HZ			1000		/* decrementer freq: 1 ms ticks */
 
 						/* valid baudrates */
include/configs/lart.h +0 -2
index 38b8e75..877d5c7 100644
@@ -102,8 +102,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xc0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0xc8000000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			3686400		/* incrementer freq: 3.6864 MHz */
include/configs/logodl.h +0 -2
index cd105da..9afa800 100644
@@ -108,8 +108,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x08000000      /* memtest works on             */
 #define CONFIG_SYS_MEMTEST_END         0x0800ffff	/* 64 KiB                       */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR           0x08000000      /* load kernel to this address   */
 
 #define CONFIG_SYS_HZ			1000
include/configs/lpc2292sodimm.h +0 -2
index 563d35b..fa2917e 100644
@@ -106,8 +106,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x40000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x40000000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x00040000	/* default load address	for	*/
 						/* armadillo: kernel img is here*/
 
include/configs/lpd7a400.h +0 -2
index 575f2a1..b1bd74f 100644
@@ -99,8 +99,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0300000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xc0500000	/* 2 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0xc0f00000	/* default load address	*/
 
 /* valid baudrates */
include/configs/lpd7a404.h +0 -2
index 3e726a0..b197674 100644
@@ -99,8 +99,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0300000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xc0500000	/* 2 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0xc0f00000	/* default load address	*/
 
 /* valid baudrates */
include/configs/lubbock.h +0 -2
index 69774d7..a4b430b 100644
@@ -122,8 +122,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */
 
 #define CONFIG_SYS_HZ			1000
include/configs/modnet50.h +0 -2
index 27213a8..b8ae018 100644
@@ -111,8 +111,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x00400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x00800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x00500000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			900		/* decrementer freq: 2 kHz */
include/configs/mx1ads.h +0 -1
index f136b0c..c3812e6 100644
@@ -133,7 +133,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x09000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0AF00000	/* 63 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ				/* everything, incl board info, in Hz */
 #define CONFIG_SYS_LOAD_ADDR		0x08800000	/* default load address */
 /*#define	CONFIG_SYS_HZ			1000 */
 #define CONFIG_SYS_HZ			3686400
include/configs/mx1fs2.h +0 -2
index a19eb78..b174b5f 100644
@@ -80,8 +80,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x08100000	      /* memtest test area   */
 #define CONFIG_SYS_MEMTEST_END		0x08F00000
 
-#undef	CONFIG_SYS_CLKS_IN_HZ			     /* use HZ for freq. display     */
-
 #define CONFIG_SYS_HZ			3686400	     /* incrementer freq: 3.6864 MHz */
 #define CONFIG_SYS_CPUSPEED		0x141	     /* core clock - register value  */
 
include/configs/netstar.h +0 -2
index 0b38549..37450d4 100644
@@ -211,8 +211,6 @@
 #define CONFIG_SYS_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - \
 				(CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_MALLOC_LEN + CONFIG_STACKSIZE)
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		PHYS_SDRAM_1 + 0x400000	/* default load address */
 
 /* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
include/configs/nmdk8815.h +0 -1
index 543780d..6d7b94f 100644
@@ -96,7 +96,6 @@
 /* timing informazion */
 #define CONFIG_SYS_HZ		(2400000 / 256)	/* Timer0: 2.4Mhz + divider */
 #define CONFIG_SYS_TIMERBASE	0x101E2000
-#undef	CONFIG_SYS_CLKS_IN_HZ
 
 /* serial port (PL011) configuration */
 #define CONFIG_PL011_SERIAL
include/configs/ns9750dev.h +0 -2
index b22c33c..79dcd64 100644
@@ -122,8 +122,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x00780000	/* 7,5 MB in DRAM	*/ /* @TODO */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x00600000	/* default load address	*/ /* @TODO */
 
 #define	CONFIG_SYS_HZ			(CPU_CLK_FREQ/64)
include/configs/omap1510inn.h +0 -2
index c7d1b6c..ac5040a 100644
@@ -130,8 +130,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x10000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x12000000	/* 32 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0x10000000	/* default load address */
 
 /* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
include/configs/omap1610h2.h +0 -2
index e2a6360..79cf608 100644
@@ -125,8 +125,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x10000000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END	0x12000000	/* 32 MB in DRAM */
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR	0x10000000	/* default load address */
 
 /* The 1610 has 6 timers, they can be driven by the RefClk (12Mhz) or by
include/configs/omap1610inn.h +0 -2
index 5dcfce1..ce30f55 100644
@@ -130,8 +130,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x10000000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END	0x12000000	/* 32 MB in DRAM    */
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR	0x10000000	/* default load address */
 
 /* The 1610 has 6 timers, they can be driven by the RefClk (12Mhz) or by
include/configs/omap2420h4.h +0 -2
index 983b5f2..aa82326 100644
@@ -216,8 +216,6 @@
 #define CONFIG_SYS_MEMTEST_START        (OMAP2420_SDRC_CS0)  /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END          (OMAP2420_SDRC_CS0+SZ_31M)
 
-#undef	CONFIG_SYS_CLKS_IN_HZ           /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR            (OMAP2420_SDRC_CS0) /* default load address */
 
 /* The 2420 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
include/configs/omap3_beagle.h +0 -2
index 9057606..62c7479 100644
@@ -214,8 +214,6 @@
 #define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
 					0x01F00000) /* 31MB */
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)	/* default */
 							/* load address */
 
include/configs/omap3_evm.h +0 -3
index f4498a9..baf71f4 100644
@@ -212,9 +212,6 @@
 #define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
 					0x01F00000) /* 31MB */
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, */
-					/* in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0) /* default load */
 								/* address */
 
include/configs/omap3_overo.h +0 -3
index dee0417..02d4fbc 100644
@@ -206,9 +206,6 @@
 #define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
 					0x01F00000) /* 31MB */
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, */
-					/* in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0) /* default load */
 								/* address */
 
include/configs/omap3_pandora.h +0 -3
index 00c0374..9a32452 100644
@@ -208,9 +208,6 @@
 #define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
 					0x01F00000) /* 31MB */
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, */
-					/* in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0) /* default load */
 								/* address */
 
include/configs/omap3_zoom1.h +0 -2
index f8ae163..b544ea1 100644
@@ -216,8 +216,6 @@
 #define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
 					0x01F00000) /* 31MB */
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)	/* default */
 							/* load address */
 
include/configs/omap5912osk.h +0 -2
index 63cd9c6..2bc5383 100644
@@ -134,8 +134,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x10000000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END	0x12000000	/* 32 MB in DRAM    */
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR	0x10000000	/* default load address */
 
 /* The 1610 has 6 timers, they can be driven by the RefClk (12Mhz) or by
include/configs/omap730p2.h +0 -2
index 166d592..0b0d8b6 100644
@@ -142,8 +142,6 @@
 #define CONFIG_SYS_MEMTEST_START	   0x10000000	       /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		   0x12000000	       /* 32 MB in DRAM	   */
 
-#undef CONFIG_SYS_CLKS_IN_HZ		     /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		   0x10000000	       /* default load address */
 
 /* The OMAP730 has 3 general purpose MPU timers, they can be driven by
include/configs/pdnb3.h +0 -1
index 4da401f..edaa81b 100644
@@ -117,7 +117,6 @@
 #define CONFIG_SYS_MEMTEST_END         0x00800000      /* 4 ... 8 MB in DRAM   */
 #define CONFIG_SYS_LOAD_ADDR           0x00010000      /* default load address */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
 #define CONFIG_SYS_HZ			1000		/* decrementer freq: 1 ms ticks */
 						/* valid baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
include/configs/pleb2.h +0 -2
index 59741a9..ab9ea4f 100644
@@ -122,8 +122,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0xa2000000	/* default load address */
 
 #define CONFIG_SYS_HZ			1000
include/configs/pxa255_idp.h +0 -2
index d1c2c65..5e2e7cf 100644
@@ -236,8 +236,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0xa0800000	/* default load address */
 
 #define CONFIG_SYS_HZ			1000
include/configs/sbc2410x.h +0 -2
index bf4a14e..102c45a 100644
@@ -135,8 +135,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x30000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x33F00000	/* 63 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x33000000	/* default load address	*/
 
 /* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
include/configs/sc520_cdp.h +0 -2
index 960350c..3e2bb02 100644
@@ -116,8 +116,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x01000000	/* 1 ... 16 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			1024		/* incrementer freq: 1kHz */
include/configs/sc520_spunk.h +0 -2
index 2445a34..d42ef84 100644
@@ -117,8 +117,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x01000000	/* 1 ... 16 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			1024		/* incrementer freq: 1kHz */
include/configs/scb9328.h +0 -2
index 5971df7..10db535 100644
@@ -86,8 +86,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x08100000	      /* memtest test area   */
 #define CONFIG_SYS_MEMTEST_END		0x08F00000
 
-#undef	CONFIG_SYS_CLKS_IN_HZ			     /* use HZ for freq. display     */
-
 #define CONFIG_SYS_HZ			3686400	     /* incrementer freq: 3.6864 MHz */
 #define CONFIG_SYS_CPUSPEED		0x141	     /* core clock - register value  */
 
include/configs/shannon.h +0 -2
index 75ba34c..717036c 100644
@@ -105,8 +105,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xc0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xc0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0xd0000000	/* default load address	*/
 
 #define	CONFIG_SYS_HZ			3686400		/* incrementer freq: 3.6864 MHz */
include/configs/smdk2400.h +0 -2
index 6388be4..856d1fb 100644
@@ -137,8 +137,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x0c000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0e000000	/* 32 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x0cf00000	/* default load address	*/
 
 /* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
include/configs/smdk2410.h +0 -2
index ecd958b..797a596 100644
@@ -120,8 +120,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x30000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x33F00000	/* 63 MB in DRAM	*/
 
-#undef  CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x33000000	/* default load address	*/
 
 /* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
include/configs/trab.h +0 -2
index 8f13c35..625d8ee 100644
@@ -316,8 +316,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x0C000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0D000000	/* 16 MB in DRAM	*/
 
-#undef CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define	CONFIG_SYS_LOAD_ADDR		0x0CF00000	/* default load address	*/
 
 #ifdef CONFIG_TRAB_50MHZ
include/configs/trizepsiv.h +0 -2
index 70e5ce9..c2744b5 100644
@@ -163,8 +163,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0xa1000000	/* default load address */
 
 #define CONFIG_SYS_HZ			1000
include/configs/versatile.h +0 -1
index 852becb..8f6383b 100644
@@ -144,7 +144,6 @@
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args   */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
 #define CONFIG_SYS_LOAD_ADDR	0x7fc0	/* default load address */
 
 /*-----------------------------------------------------------------------
include/configs/voiceblue.h +0 -2
index cadd906..b76c794 100644
@@ -210,8 +210,6 @@
 #define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1
 #define CONFIG_SYS_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 /* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
  * This time is further subdivided by a local divisor.
  */
include/configs/wepep250.h +0 -2
index d0afd29..717577f 100644
@@ -79,8 +79,6 @@
 #define CONFIG_SYS_MEMTEST_START       0xa0400000            /* memtest test area   */
 #define CONFIG_SYS_MEMTEST_END         0xa0800000
 
-#undef  CONFIG_SYS_CLKS_IN_HZ                       /* use HZ for freq. display     */
-
 #define CONFIG_SYS_HZ			1000
 #define CONFIG_SYS_CPUSPEED            0x141        /* core clock - register value  */
 
include/configs/xaeniax.h +0 -2
index 250247c..086ca69 100644
@@ -134,8 +134,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ				/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0xa1000000	/* default load address */
 
 #define CONFIG_SYS_HZ			1000
include/configs/xm250.h +0 -2
index 8e9d5ab..922eb2c 100644
@@ -117,8 +117,6 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on		*/
 #define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM		*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR		0xa3000000	/* default load address */
 
 #define CONFIG_SYS_HZ			1000
include/configs/xsengine.h +0 -1
index 5d13f96..cad414c 100644
@@ -139,7 +139,6 @@
 #define CONFIG_SYS_BARGSIZE			CONFIG_SYS_CBSIZE				/* Boot Argument Buffer Size */
 #define CONFIG_SYS_MEMTEST_START		0xA0400000				/* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END			0xA0800000				/* 4 ... 8 MB in DRAM   */
-#undef  CONFIG_SYS_CLKS_IN_HZ								/* everything, incl board info, in Hz */
 #define CONFIG_SYS_BAUDRATE_TABLE		{ 9600, 19200, 38400, 57600, 115200 }	/* valid baudrates */
 #define CONFIG_SYS_LOAD_ADDR			0xA0000000				/* load kernel to this address   */
 
include/configs/zylonite.h +0 -2
index 6febeea..064740d 100644
@@ -139,8 +139,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x9c000000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x9c400000	/* 4 ... 8 MB in DRAM	*/
 
-#undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */
 
 #define CONFIG_SYS_HZ			1000