omap3evm mmc problem
Subsystems (3)
Does anyone else get these mmc errors or know why on the OMAP 3530 Development board ?
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
regulator: Unable to get requested regulator: vmmc mmci-omap-hs mmci-omap-hs.0: err -19 configuring card detect mmci-omap-hs mmci-omap-hs.0: late init error mmci-omap-hs mmci-omap-hs.0: Probe Failed
I'm using the current git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
Quoted 1 line · dfoley
Does anyone else get these mmc errors or know why on the OMAP 3530 Development board ?
Which dev board? LDP? EVM?
Quoted 2 lines
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
regulator: Unable to get requested regulator: vmmc
Needs patches to setup whichever regulator is used with the MMC1 controller. Look at Beagle, Overo, or SDP for examples...
Quoted 1 line
mmci-omap-hs mmci-omap-hs.0: err -19 configuring card detect
Tony Lindgren
maintainerQuoted 6 lines · David Brownell
Quoted 1 line · dfoley
Does anyone else get these mmc errors or know why on the OMAP 3530 Development board ?
Which dev board? LDP? EVM?
Quoted 9 lines
Quoted 2 lines
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
regulator: Unable to get requested regulator: vmmcNeeds patches to setup whichever regulator is used with the MMC1 controller. Look at Beagle, Overo, or SDP for examples...
Quoted 1 line
mmci-omap-hs mmci-omap-hs.0: err -19 configuring card detect
Is this again the CONFIG_REGULATOR missing in .config?
Tony
Quoted 10 lines · Tony Lindgren
Quoted 9 lines · David Brownell
Quoted 1 line · dfoley
Does anyone else get these mmc errors or know why on the OMAP 3530 Development board ?
Which dev board? LDP? EVM?
Quoted 2 lines
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
regulator: Unable to get requested regulator: vmmc
Quoted 8 lines
Quoted 6 lines
Needs patches to setup whichever regulator is used with the MMC1 controller. Look at Beagle, Overo, or SDP for examples...
Quoted 1 line
mmci-omap-hs mmci-omap-hs.0: err -19 configuring card detect
Is this again the
CONFIG_REGULATORmissing in .config?
Maybe. Do all the boards set up their regulators now?
Quoted 15 lines · David Brownell
Quoted 14 lines · Tony Lindgren
Quoted 13 lines · David Brownell
Quoted 1 line · dfoley
Does anyone else get these mmc errors or know why on the OMAP 3530 Development board ?
Which dev board? LDP? EVM?
Quoted 2 lines
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
regulator: Unable to get requested regulator: vmmcNeeds patches to setup whichever regulator is used with the MMC1 controller. Look at Beagle, Overo, or SDP for examples...
Quoted 1 line
mmci-omap-hs mmci-omap-hs.0: err -19 configuring card detect
Quoted 9 lines
Quoted 1 line
Is this again the
CONFIG_REGULATORmissing in .config?Maybe. Do all the boards set up their regulators now?
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
SD seems to work now with patch below and REGULATOR_TWL4030 [=y]. For the patch, I just copied from other boards in mach-omap2, so I really have no idea if it's correct.
git tree:5a824e035b9ab16aa81c021c34c557b90d10c7e6 branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
output:
root@tsi-omap3evm:~# dmesg | grep mmc mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock mmc0: new high speed SD card at address 0007 mmcblk0: mmc0:0007 SD01G 972 MiB mmcblk0: p1 VFS: Can't find a valid FAT filesystem on dev mmcblk0. EXT3 FS on mmcblk0p1, internal journal
arch/arm/mach-omap2/board-omap3evm.c +45 -1
@@ -24,6 +24,7 @@#include <linux/spi/spi.h> #include <linux/spi/ads7846.h> #include <linux/i2c/twl4030.h> +#include <linux/regulator/machine.h> #include <mach/hardware.h> #include <asm/mach-types.h>
@@ -99,6 +100,14 @@ static struct twl4030_hsmmc_info mmc[] = { {}/* Terminator */ }; +static struct regulator_consumer_supply omap3evm_vmmc1_supply = { + .supply ="vmmc" , +}; + +static struct regulator_consumer_supply omap3evm_vsim_supply = { + .supply ="vmmc_aux" , +}; +static struct gpio_led gpio_leds[] = { { .name ="omap3evm::ledb" ,
@@ -122,7 +131,6 @@ static struct platform_device leds_gpio = { }, }; -static int omap3evm_twl_gpio_setup (struct device *dev,unsigned gpio,unsigned ngpio) {
@@ -131,6 +139,9 @@ static int omap3evm_twl_gpio_setup(struct device *dev, mmc[0 ].gpio_cd = gpio +0 ;twl4030_mmc_init (mmc); + omap3evm_vmmc1_supply.dev = mmc[0 ].dev; + omap3evm_vsim_supply.dev = mmc[0 ].dev; +/* Most GPIOs are for USB OTG. Some are mostly sent to * the P2 connector; notably LEDA for the LCD backlight. */
@@ -186,6 +197,37 @@ static struct twl4030_madc_platform_data omap3evm_madc_data = { .irq_line = 1, }; +/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */ +static struct regulator_init_data omap3evm_vmmc1 = { + .constraints = { + .min_uV =1850000 , + .max_uV =3150000 , + .valid_modes_mask =REGULATOR_MODE_NORMAL + |REGULATOR_MODE_STANDBY , + .valid_ops_mask =REGULATOR_CHANGE_VOLTAGE + |REGULATOR_CHANGE_MODE + |REGULATOR_CHANGE_STATUS , + }, + .num_consumer_supplies =1 , + .consumer_supplies = &omap3evm_vmmc1_supply, +}; + +/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */ +static struct regulator_init_data omap3evm_vsim = { + .constraints = { + .min_uV =1800000 , + .max_uV =3000000 , + .valid_modes_mask =REGULATOR_MODE_NORMAL + |REGULATOR_MODE_STANDBY , + .valid_ops_mask =REGULATOR_CHANGE_VOLTAGE + |REGULATOR_CHANGE_MODE + |REGULATOR_CHANGE_STATUS , + }, + .num_consumer_supplies =1 , + .consumer_supplies = &omap3evm_vsim_supply, +}; + +static struct twl4030_platform_data omap3evm_twldata = { .irq_base =TWL4030_IRQ_BASE , .irq_end =TWL4030_IRQ_END ,
@@ -196,6 +238,8 @@ static struct twl4030_platform_data omap3evm_twldata = { .usb = &omap3evm_usb_data, .power = GENERIC3430_T2SCRIPTS_DATA, .gpio = &omap3evm_gpio_data, + .vmmc1 = &omap3evm_vmmc1, + .vsim = &omap3evm_vsim, };static struct i2c_board_info __initdata omap3evm_i2c_boardinfo[] = {
Quoted 4 lines · dfoley
SD seems to work now with patch below and
REGULATOR_TWL4030[=y]. For the patch, I just copied from other boards in mach-omap2, so I really have no idea if it's correct.
I think you don't need to set up VSIM, since that board only seems to support 4-wire SD cards (not 8-wire MMCplus). Else mmc[0].wires == 4 would be wrong...