Skip to contentSkip to conversation

ppc: using d-cache for C stack and as cache at the same time?

U-Boot Jens Gehrlein 4 participants 7 messages Apr 1, 2009

lore
Share & tools
lore
#0 lore raw

Hi,

AFAIK, while running from flash, u-boot uses (part of) d-cache on some platforms for the C stack. I think, it's on MPC83xx and MPC85xx?

Does anybody know, if I can use the remaining part of the d-cache as normal d-cache, e.g. to generate bursts on the SDRAM interface while testing the RAM?

Kind regards,
Jens

#1 lore raw

Dear Jens Gehrlein,

Quoted 7 lines · In message <[email protected]> you wrote:

AFAIK, while running from flash, u-boot uses (part of) d-cache on some platforms for the C stack. I think, it's on MPC83xx and MPC85xx?

Does anybody know, if I can use the remaining part of the d-cache as normal d-cache, e.g. to generate bursts on the SDRAM interface while testing the RAM?

On which platform?

Note that implementing a memory test that actually triggers burst mode accesses is really, really tricky. You probably do NOT want to do this while running from flash (i. e. from a very restrictive envrionment). You might want to have a look at examples/test_burst* but note that this code was written for a MPC8xx system, so changes will be required for 83xx or 85xx.

Also note that a much more reliable test for burst mode errors is to boot Linux with root file system over NFS and then compile the Linux kernel on the target.

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Bus error -- driver executed.
#2 lore raw

[U-Boot] ppc: using d-cache for C stack and as cache at thesame time?

Quoted 17 lines
Quoted 1 line

AFAIK, while running from flash, u-boot uses (part of)

d-cache on some

Quoted 5 lines

platforms for the C stack. I think, it's on MPC83xx and MPC85xx?

Does anybody know, if I can use the remaining part of the d-cache as normal d-cache, e.g. to generate bursts on the SDRAM interface while testing the RAM?

On which platform?

Note that implementing a memory test that actually triggers burst mode accesses is really, really tricky. You probably do NOT want to do this while running from flash (i. e. from a very restrictive envrionment). You might want to have a look at examples/test_burst* but note that this code was written for a MPC8xx system, so changes will be required for 83xx or 85xx.

Quoted 3 lines

Also note that a much more reliable test for burst mode errors is to boot Linux with root file system over NFS and then compile the Linux kernel on the target.

It needs case by case.

* 83xx, the whole d-cache is locked
If you need generate bursts on DRAM interface, you have to change to way locked. Otherwise, you can use the DMA to generate burst.

* 85xx, half of d-cache is locked.
it is possible to generate the burst at 85xx.
Try to use dcbf....

Thanks, Dave

#3 lore raw

[U-Boot] ppc: using d-cache for C stack and as cache at thesame time?

Quoted 20 lines · Liu Dave-R63238 schrieb:
Quoted 16 lines
Quoted 1 line

AFAIK, while running from flash, u-boot uses (part of)

d-cache on some

Quoted 5 lines

platforms for the C stack. I think, it's on MPC83xx and MPC85xx?

Does anybody know, if I can use the remaining part of the d-cache as normal d-cache, e.g. to generate bursts on the SDRAM interface while testing the RAM?

On which platform?

Note that implementing a memory test that actually triggers burst mode accesses is really, really tricky. You probably do NOT want to do this while running from flash (i. e. from a very restrictive envrionment). You might want to have a look at examples/test_burst* but note that this code was written for a MPC8xx system, so changes will be required for 83xx or 85xx.

Quoted 3 lines

Also note that a much more reliable test for burst mode errors is to boot Linux with root file system over NFS and then compile the Linux kernel on the target.

Quoted 5 lines

It needs case by case.

* 83xx, the whole d-cache is locked
If you need generate bursts on DRAM interface, you have to change to way locked. Otherwise, you can use the DMA to generate burst.

Good idea.

Quoted 3 lines

* 85xx, half of d-cache is locked.
it is possible to generate the burst at 85xx.
Try to use dcbf....

Thank you for the hints.

Kind regards,
Jens

#4 lore raw

[U-Boot] ppc: using d-cache for C stack and as cache at thesame time?

In reply to Liu Dave-R63238
Quoted 23 lines · On Wed, 2009-04-01 at 17:29 +0800, Liu Dave-R63238 wrote:
Quoted 17 lines
Quoted 1 line

AFAIK, while running from flash, u-boot uses (part of)

d-cache on some

Quoted 5 lines

platforms for the C stack. I think, it's on MPC83xx and MPC85xx?

Does anybody know, if I can use the remaining part of the d-cache as normal d-cache, e.g. to generate bursts on the SDRAM interface while testing the RAM?

On which platform?

Note that implementing a memory test that actually triggers burst mode accesses is really, really tricky. You probably do NOT want to do this while running from flash (i. e. from a very restrictive envrionment). You might want to have a look at examples/test_burst* but note that this code was written for a MPC8xx system, so changes will be required for 83xx or 85xx.

Quoted 3 lines

Also note that a much more reliable test for burst mode errors is to boot Linux with root file system over NFS and then compile the Linux kernel on the target.

It needs case by case.

Quoted 7 lines

* 83xx, the whole d-cache is locked
If you need generate bursts on DRAM interface, you have to change to way locked. Otherwise, you can use the DMA to generate burst.

* 85xx, half of d-cache is locked.
it is possible to generate the burst at 85xx.
Try to use dcbf....

You should be able to use the 85xx DMA engine to generate the bursts too (I'd assume the same for 83xx, but never tried it). See cpu/mpc85xx/cpu.c dma_*(). The default values of the satr0 and datr0 don't allow the processor to snoop transactions, so you'd have to use cache operations or change datr0/satr0 to something like 0x50000 for your tests.

We've added a very basic DMA test to the mtest command which is used for board testing here. Let me know if you'd like me to send it - its not cleaned up but could give you a starting point.

Best,
Peter

#5 lore raw

[U-Boot] ppc: using d-cache for C stack and as cache at thesame time?

Quoted 10 lines · Peter Tyser

You should be able to use the 85xx DMA engine to generate the bursts too (I'd assume the same for 83xx, but never tried it). See cpu/mpc85xx/cpu.c dma_*(). The default values of the satr0 and datr0 don't allow the processor to snoop transactions, so you'd have to use cache operations or change datr0/satr0 to something like 0x50000 for your tests.

We've added a very basic DMA test to the mtest command which is used for board testing here. Let me know if you'd like me to send it - its not cleaned up but could give you a starting point.

Although, I will not start before next month with burst testing, it would be very nice, if could send it. Thank you very much.

Kind regards,
Jens

#6 lore raw
In reply to Wolfgang Denk

Dear Wolfgang Denk,

Quoted 10 lines · Wolfgang Denk

Dear Jens Gehrlein,

Quoted 6 lines · In message <[email protected]> you wrote:

AFAIK, while running from flash, u-boot uses (part of) d-cache on some platforms for the C stack. I think, it's on MPC83xx and MPC85xx?

Does anybody know, if I can use the remaining part of the d-cache as normal d-cache, e.g. to generate bursts on the SDRAM interface while testing the RAM?

Quoted 6 lines

On which platform?

Note that implementing a memory test that actually triggers burst mode accesses is really, really tricky. You probably do NOT want to do this while running from flash (i. e. from a very restrictive envrionment).

Why not? Of course, it's only possible if I can use a part of the D-Cache as C stack (or another internal RAM if available). This must be separately checked for each processor.

Quoted 3 lines

You might want to have a look at examples/test_burst*
but note that this code was written for a MPC8xx system, so changes will be required for 83xx or 85xx.

Thank you for the hint. I'll have a look.

Quoted 3 lines

Also note that a much more reliable test for burst mode errors is to boot Linux with root file system over NFS and then compile the Linux kernel on the target.

I agree.

Kind regards,
Jens