Skip to contentSkip to conversation

net/igb: Fix kexec with igb (rev. 3)

PATCH Applied Jeff Kirsher 2 participants 2 messages Apr 1, 2009 – Apr 2, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 5/5 net/igb: Fix kexec with igb (rev. 3)

From: Rafael J. Wysocki <[email protected]>

Impact: Fix

Yinghai Lu found one system with 82575EB where, in the kernel that is kexeced, probe igb failed with -2, the reason being that the adapter could not be brought back from D3 by the kexec kernel, most probably due to quirky hardware (it looks like the same behavior happened on forcedeth).

Prevent igb from putting the adapter into D3 during shutdown except when we going to power off the system. For this purpose, seperate igb_shutdown() from igb_suspend() and use the appropriate PCI PM callbacks in both of them.

---

 drivers/net/igb/igb_main.c |   44 +++++++++++++++++++++++++++++++-------------
 1 files changed, 31 insertions(+), 13 deletions(-)
drivers/net/igb/igb_main.c +31 -13
index 10b095d..03aa959 100644
@@ -135,8 +135,8 @@ static inline int igb_set_vf_rlpml(struct igb_adapter *, int, int);
 static int igb_set_vf_mac(struct igb_adapter *adapter, int, unsigned char *);
 static void igb_restore_vf_multicasts(struct igb_adapter *adapter);
 
-static int igb_suspend(struct pci_dev *, pm_message_t);
 #ifdef CONFIG_PM
+static int igb_suspend(struct pci_dev *, pm_message_t);
 static int igb_resume(struct pci_dev *);
 #endif
 static void igb_shutdown(struct pci_dev *);
@@ -5060,7 +5060,7 @@ int igb_set_spd_dplx(struct igb_adapter *adapter, u16 spddplx)
 	return 0;
 }
 
-static int igb_suspend(struct pci_dev *pdev, pm_message_t state)
+static int __igb_shutdown(struct pci_dev *pdev, bool *enable_wake)
 {
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct igb_adapter *adapter = netdev_priv(netdev);
@@ -5119,15 +5119,9 @@ static int igb_suspend(struct pci_dev *pdev, pm_message_t state)
 		wr32(E1000_WUFC, 0);
 	}
 
-	/* make sure adapter isn't asleep if manageability/wol is enabled */
-	if (wufc || adapter->en_mng_pt) {
-		pci_enable_wake(pdev, PCI_D3hot, 1);
-		pci_enable_wake(pdev, PCI_D3cold, 1);
-	} else {
+	*enable_wake = wufc || adapter->en_mng_pt;
+	if (!*enable_wake)
 		igb_shutdown_fiber_serdes_link_82575(hw);
-		pci_enable_wake(pdev, PCI_D3hot, 0);
-		pci_enable_wake(pdev, PCI_D3cold, 0);
-	}
 
 	/* Release control of h/w to f/w.  If f/w is AMT enabled, this
 	 * would have already happened in close and is redundant. */
@@ -5135,12 +5129,29 @@ static int igb_suspend(struct pci_dev *pdev, pm_message_t state)
 
 	pci_disable_device(pdev);
 
-	pci_set_power_state(pdev, pci_choose_state(pdev, state));
-
 	return 0;
 }
 
 #ifdef CONFIG_PM
+static int igb_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	int retval;
+	bool wake;
+
+	retval = __igb_shutdown(pdev, &wake);
+	if (retval)
+		return retval;
+
+	if (wake) {
+		pci_prepare_to_sleep(pdev);
+	} else {
+		pci_wake_from_d3(pdev, false);
+		pci_set_power_state(pdev, PCI_D3hot);
+	}
+
+	return 0;
+}
+
 static int igb_resume(struct pci_dev *pdev)
 {
 	struct net_device *netdev = pci_get_drvdata(pdev);
@@ -5193,7 +5204,14 @@ static int igb_resume(struct pci_dev *pdev)
 
 static void igb_shutdown(struct pci_dev *pdev)
 {
-	igb_suspend(pdev, PMSG_SUSPEND);
+	bool wake;
+
+	__igb_shutdown(pdev, &wake);
+
+	if (system_state == SYSTEM_POWER_OFF) {
+		pci_wake_from_d3(pdev, wake);
+		pci_set_power_state(pdev, PCI_D3hot);
+	}
 }
 
 #ifdef CONFIG_NET_POLL_CONTROLLER
maintainer Applied
#1 lore raw

From: Jeff Kirsher <[email protected]>
Date: Wed, 01 Apr 2009 00:23:50 -0700

Quoted 8 lines

Impact: Fix

Yinghai Lu found one system with 82575EB where, in the kernel that is kexeced, probe igb failed with -2, the reason being that the adapter could not be brought back from D3 by the kexec kernel, most probably due to quirky hardware (it looks like the same behavior happened on forcedeth).

Quoted 8 lines

Prevent igb from putting the adapter into D3 during shutdown except when we going to power off the system. For this purpose, seperate igb_shutdown() from igb_suspend() and use the appropriate PCI PM callbacks in both of them.

Applied.