mpc5200: reduce delays in i2c
PATCH v3 1/1 mpc5200: reduce delays in i2c
Make the i2c delays smaller. The measured delay is 55us at 100Khz. Set the delay to 15us which should work for 400Khz. 100Khz will loop four times and get a 60us delay. Try four times at a 15us delay and then revert to the previous behavior of 1ms delays.
--- cpu/mpc5xxx/i2c.c | 9 +++++---- 1 files changed, 5 insertions(+), 4 deletions(-)
cpu/mpc5xxx/i2c.c +5 -4
@@ -39,6 +39,7 @@ DECLARE_GLOBAL_DATA_PTR;#endif #define I2C_TIMEOUT 100 +#define I2C_TIMEOUT_QUICK 4#define I2C_RETRIES 3struct mpc5xxx_i2c_tap {
@@ -80,7 +81,7 @@ static void mpc_reg_out(volatile u32 *reg, int val, int mask)static int wait_for_bb (void ) {struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE ; -int timeout =I2C_TIMEOUT ; +int timeout =I2C_TIMEOUT +I2C_TIMEOUT_QUICK ;int status; status =mpc_reg_in (®s->msr);
@@ -94,7 +95,7 @@ static int wait_for_bb(void)mpc_reg_out (®s->mcr,0 ,0 );mpc_reg_out (®s->mcr,I2C_EN ,0 );#endif -udelay (1000 ); + timeout >I2C_TIMEOUT ?udelay (15 ) :udelay (1000 ); status =mpc_reg_in (®s->msr); }
@@ -104,12 +105,12 @@ static int wait_for_bb(void)static int wait_for_pin (int *status) {struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE ; -int timeout =I2C_TIMEOUT ; +int timeout =I2C_TIMEOUT +I2C_TIMEOUT_QUICK ; *status =mpc_reg_in (®s->msr);while (timeout-- && !(*status &I2C_IF )) { -udelay (1000 ); + timeout >I2C_TIMEOUT ?udelay (15 ) :udelay (1000 ); *status =mpc_reg_in (®s->msr); }
PATCH v3 1/1 mpc5200: reduce delays in i2c
Dear Jon Smirl,
Quoted 43 lines · In message <20090331213728.17969.91950.stgit@localhost> you wrote:
Make the i2c delays smaller. The measured delay is 55us at 100Khz. Set the delay to 15us which should work for 400Khz. 100Khz will loop four times and get a 60us delay. Try four times at a 15us delay and then revert to the previous behavior of 1ms delays.
--- cpu/mpc5xxx/i2c.c | 9 +++++---- 1 files changed, 5 insertions(+), 4 deletions(-)cpu/mpc5xxx/i2c.c +3
-2@@ -39,6 +39,7 @@ DECLARE_GLOBAL_DATA_PTR;#endif #define I2C_TIMEOUT 100 +#define I2C_TIMEOUT_QUICK 4#define I2C_RETRIES 3struct mpc5xxx_i2c_tap {@@ -80,7 +81,7 @@ static void mpc_reg_out(volatile u32 *reg, int val, int mask)static int wait_for_bb (void ) {struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE ; -int timeout =I2C_TIMEOUT ; +int timeout =I2C_TIMEOUT +I2C_TIMEOUT_QUICK ;int status; status =mpc_reg_in (®s->msr);@@ -94,7 +95,7 @@ static int wait_for_bb(void)mpc_reg_out (®s->mcr,0 ,0 );mpc_reg_out (®s->mcr,I2C_EN ,0 );#endif -udelay (1000 ); + timeout >I2C_TIMEOUT ?udelay (15 ) :udelay (1000 ); status =mpc_reg_in (®s->msr); }@@ -104,12 +105,12 @@ static int wait_for_bb(void)static int wait_for_pin (int *status) {struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE ;
cpu/mpc5xxx/i2c.c static int wait_for_bb(void) · line 115
Quoted 10 lines
cpu/mpc5xxx/i2c.c +2
-2-int timeout =I2C_TIMEOUT ; +int timeout =I2C_TIMEOUT +I2C_TIMEOUT_QUICK ; *status =mpc_reg_in (®s->msr);while (timeout-- && !(*status &I2C_IF )) { -udelay (1000 ); + timeout >I2C_TIMEOUT ?udelay (15 ) :udelay (1000 ); *status =mpc_reg_in (®s->msr); }
Urgh... Why are you making this so complicated. This is definitely not needed. Why don't you just stick with the last (or before last?) version and adjut the total timeouts to the original values?
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Remember, there's a big difference between kneeling down and bending over. - Frank Zappa