at91: Improved Atmel AT45DB081 dataflash support
Subsystems (2)
PATCH 1/2 at91: Improved Atmel AT45DB081 dataflash support
This patch improves Atmel AT45DB081 dataflash support.
--- drivers/mtd/dataflash.c | 7 ++++--- 1 files changed, 4 insertions(+), 3 deletions(-)
drivers/mtd/dataflash.c +4 -3
@@ -199,7 +199,7 @@ void dataflash_print_info (void)for (i =0 ; i <CONFIG_SYS_MAX_DATAFLASH_BANKS ; i++) {if (dataflash_info[i].id !=0 ) { -printf ("DataFlash:" ); +printf ("DataFlash: " );switch (dataflash_info[i].id) {case AT45DB021 :printf ("AT45DB021\n" );
@@ -207,11 +207,12 @@ void dataflash_print_info (void)case AT45DB161 :printf ("AT45DB161\n" );break ; - +case AT45DB081 : +printf ("AT45DB081\n" ); +break ;case AT45DB321 :printf ("AT45DB321\n" );break ; -case AT45DB642 :printf ("AT45DB642\n" );break ;
Signature · 1 line
1.6.1
PATCH 2/2 at91: Add support for esd MEESC board
This patch adds support for MEESC board from esd gmbh. The MEESC is based on an Atmel AT91SAM9263 SoC.
--- MAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + board/esd/meesc/Makefile | 54 ++++++ board/esd/meesc/config.mk | 1 + board/esd/meesc/meesc.c | 400 +++++++++++++++++++++++++++++++++++++++++++++ include/configs/meesc.h | 185 +++++++++++++++++++++ 7 files changed, 648 insertions(+), 0 deletions(-) create mode 100644 board/esd/meesc/Makefile create mode 100644 board/esd/meesc/config.mk create mode 100644 board/esd/meesc/meesc.c create mode 100644 include/configs/meesc.h
MAINTAINERS +4 -0
@@ -517,6 +517,10 @@ Peter Figuli <[email protected]> wepep250 xscale +Daniel Gorsulowski <[email protected]> + + meesc ARM926EJS (AT91SAM9263 SoC) + Marius Gr?ger <[email protected]> impa7 ARM720T (EP7211)
MAKEALL +1 -0
@@ -578,6 +578,7 @@ LIST_at91=" \ cmc_pu2 \ csb637 \ kb9202 \ + meesc \ mp2usb \ m501sk \ "
Makefile +3 -0
@@ -2739,6 +2739,9 @@ at91sam9rlek_config : unconfig fi; @$(MKCONFIG) -a at91sam9rlek arm arm926ejs at91sam9rlek atmel at91 +meesc_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm926ejs meesc esd at91 + ######################################################################## ## ARM Integrator boards - see doc/README-integrator for more info. integratorap_config \
board/esd/meesc/Makefile new file +54 -0
54 lines not on this page · raw message
board/esd/meesc/config.mk new file +1 -0
@@ -0,0 +1 @@ +TEXT_BASE = 0x21f00000
board/esd/meesc/meesc.c new file +400 -0
400 lines not on this page · raw message
include/configs/meesc.h new file +185 -0
185 lines not on this page · raw message
Signature · 1 line
1.6.1
PATCH 2/2 at91: Add support for esd MEESC board
Dear Daniel Gorsulowski,
Quoted 6 lines · In message <[email protected]> you wrote:
--===============0533980373==
This patch adds support for MEESC board from esd gmbh. The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by Daniel Gorsulowski <[email protected]>
...
Quoted 5 lines
board/esd/meesc/meesc.c new file +0
-0
...
board/esd/meesc/meesc.c line 128
Quoted 11 lines
board/esd/meesc/meesc.c new file +11
-0+at91_sys_write (AT91_SMC1_CYCLE (0 ), +AT91_SMC_NWECYCLE_ (10 ) |AT91_SMC_NRDCYCLE_ (5 )); +/* Configure behavior at external wait signal, byte-select mode, 16 bit +data bus width, none data float wait states and TDF optimization */ +at91_sys_write (AT91_SMC1_MODE (0 ), +AT91_SMC_READMODE | +AT91_SMC_EXNWMODE_READY | +AT91_SMC_BAT_SELECT | +AT91_SMC_DBW_16 | +AT91_SMC_TDF_ (0 ) | +AT91_SMC_TDFMODE );
Indentation wrong.
...
board/esd/meesc/meesc.c line 257
Quoted 6 lines
board/esd/meesc/meesc.c new file +6
-0+int dram_init (void ) +{ + gd->bd->bi_dram[0 ].start =PHYS_SDRAM ; + gd->bd->bi_dram[0 ].size =PHYS_SDRAM_SIZE ; +return (0 ); +}
Auto-sizing?
..
Quoted 12 lines
board/esd/meesc/meesc.c new file +12
-0+/* +* LED-functions +*/ +int do_led_1a (cmd_tbl_t *cmdtp,int flag,int argc,char *argv[]) +{ +return (set_gpio (argc, argv,LED1A )); +} +U_BOOT_CMD ( + led_1a,2 ,1 , do_led_1a, +"switch LED1A on or off" , +"\n" +);
board/esd/meesc/meesc.c line 331
Quoted 10 lines
board/esd/meesc/meesc.c new file +10
-0+ +int do_led_1b (cmd_tbl_t *cmdtp,int flag,int argc,char *argv[]) +{ +return (set_gpio (argc, argv,LED1B )); +} +U_BOOT_CMD ( + led_1b,2 ,1 , do_led_1b, +"switch LED1B on or off" , +"\n" +);
Do we really, really need new, nonstandard LED commands?
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Either one of us, by himself, is expendable. Both of us are not. -- Kirk, "The Devil in the Dark", stardate 3196.1
PATCH 2/2 at91: Add support for esd MEESC board
In reply to Daniel Gorsulowskiboard/esd/meesc/Makefile line 32
Quoted 10 lines
board/esd/meesc/Makefile new file +10
-0+# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS-y += meesc.o
please use $(BOARD)
Quoted 81 lines
board/esd/meesc/Makefile new file +22
-0+ +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################board/esd/meesc/config.mk new file +1
-0@@ -0,0 +1 @@ +TEXT_BASE = 0x21f00000board/esd/meesc/meesc.c new file +46
-0@@ -0,0 +1,400 @@ +/* +* (C) Copyright 2007-2008 +* Stelian Pop <[email protected]> +* Lead Tech Design <www.leadtechdesign.com> +* +* (C) Copyright 2008 +* Ulf Samuelsson <[email protected]> +* +* (C) Copyright 2009 +* Daniel Gorsulowski <[email protected]> +* esd electronic system design gmbh <www.esd.eu> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <common.h> +#include <asm/arch/at91sam9263.h> +#include <asm/arch/at91sam9263_matrix.h> +#include <asm/arch/at91sam9_smc.h> +#include <asm/arch/at91_pmc.h> +#include <asm/arch/at91_rstc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/io.h> +#include <asm/arch/hardware.h> +#include <nand.h> +#include <dataflash.h> + +DECLARE_GLOBAL_DATA_PTR ; + +/*
board/esd/meesc/meesc.c line 56
Quoted 10 lines
board/esd/meesc/meesc.c new file +10
-0+* Miscelaneous platform dependent initialisations +*/ + +static void meesc_serial_hw_init (void ) +{ +/* initialize DBGU pins*/ +at91_set_A_periph (AT91_PIN_PC30 ,0 );/* DRXD */ +at91_set_A_periph (AT91_PIN_PC31 ,1 );/* DTXD */ +at91_sys_write (AT91_PMC_PCER ,1 <<AT91_ID_SYS ); +}
please use new hw_init framwork
Quoted 44 lines
board/esd/meesc/meesc.c new file +44
-0+ +#define LED1A AT91_PIN_PB8 +#define LED1B AT91_PIN_PB7 +static void meesc_gpio_hw_init (void ) +{ +/* Peripheral Clock Enable Register */ +at91_sys_write (AT91_PMC_PCER ,1 <<AT91SAM9263_ID_PIOA | +1 <<AT91SAM9263_ID_PIOB | +1 <<AT91SAM9263_ID_PIOCDE ); + +/* defines ports as output */ +at91_set_gpio_output (LED1A ,0 ); +at91_set_gpio_output (LED1B ,0 ); +} + +#ifdef CONFIG_CMD_NAND +static void meesc_nand_hw_init (void ) +{ +unsigned long csa; + +/* Enable CS3 */ + csa =at91_sys_read (AT91_MATRIX_EBI0CSA ); +at91_sys_write (AT91_MATRIX_EBI0CSA , + csa |AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA ); + +/* Configure SMC CS3 for NAND/SmartMedia */ +at91_sys_write (AT91_SMC_SETUP (3 ), +AT91_SMC_NWESETUP_ (1 ) |AT91_SMC_NCS_WRSETUP_ (0 ) | +AT91_SMC_NRDSETUP_ (1 ) |AT91_SMC_NCS_RDSETUP_ (0 )); +at91_sys_write (AT91_SMC_PULSE (3 ), +AT91_SMC_NWEPULSE_ (3 ) |AT91_SMC_NCS_WRPULSE_ (3 ) | +AT91_SMC_NRDPULSE_ (3 ) |AT91_SMC_NCS_RDPULSE_ (3 )); +at91_sys_write (AT91_SMC_CYCLE (3 ), +AT91_SMC_NWECYCLE_ (5 ) |AT91_SMC_NRDCYCLE_ (5 )); +at91_sys_write (AT91_SMC_MODE (3 ), +AT91_SMC_READMODE |AT91_SMC_WRITEMODE | +AT91_SMC_EXNWMODE_DISABLE | +#ifdef CONFIG_SYS_NAND_DBW_16 +AT91_SMC_DBW_16 | +#else /* CONFIG_SYS_NAND_DBW_8 */ +AT91_SMC_DBW_8 | +#endif +AT91_SMC_TDF_ (2 )); +
board/esd/meesc/meesc.c line 110
Quoted 10 lines
board/esd/meesc/meesc.c new file +10
-0+/* Configure RDY/BSY */ +at91_set_gpio_input (CONFIG_SYS_NAND_READY_PIN ,1 ); + +/* Enable NandFlash */ + at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); +} +#endif /* CONFIG_CMD_NAND */ + +static void meesc_ethercat_hw_init (void ) +{
do you have intention to use it in U-Boot?
Quoted 21 lines
board/esd/meesc/meesc.c new file +21
-0+/* Configure SMC EBI1_CS0 for EtherCAT */ +at91_sys_write (AT91_SMC1_SETUP (0 ), +AT91_SMC_NWESETUP_ (0 ) |AT91_SMC_NCS_WRSETUP_ (0 ) | +AT91_SMC_NRDSETUP_ (0 ) |AT91_SMC_NCS_RDSETUP_ (0 )); +at91_sys_write (AT91_SMC1_PULSE (0 ), +AT91_SMC_NWEPULSE_ (4 ) |AT91_SMC_NCS_WRPULSE_ (9 ) | +AT91_SMC_NRDPULSE_ (4 ) |AT91_SMC_NCS_RDPULSE_ (9 )); +at91_sys_write (AT91_SMC1_CYCLE (0 ), +AT91_SMC_NWECYCLE_ (10 ) |AT91_SMC_NRDCYCLE_ (5 )); +/* Configure behavior at external wait signal, byte-select mode, 16 bit +data bus width, none data float wait states and TDF optimization */ +at91_sys_write (AT91_SMC1_MODE (0 ), +AT91_SMC_READMODE | +AT91_SMC_EXNWMODE_READY | +AT91_SMC_BAT_SELECT | +AT91_SMC_DBW_16 | +AT91_SMC_TDF_ (0 ) | +AT91_SMC_TDFMODE ); + +/* Configure RDY/BSY */ +at91_set_B_periph (AT91_PIN_PE20 ,0 );/* EBI1_NWAIT */
board/esd/meesc/meesc.c
Quoted 10 lines
board/esd/meesc/meesc.c new file +9
-0+} + +int board_init (void ) +{ +/* Enable Ctrlc */ +console_init_f (); + +/* arch number of AT91SAM9263EK-Board */ + gd->bd->bi_arch_number =MACH_TYPE_AT91SAM9263EK ;
please use your own arch number
Quoted 88 lines
board/esd/meesc/meesc.c new file +88
-0+/* adress of boot parameters */ + gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; + +meesc_serial_hw_init (); +meesc_gpio_hw_init (); +#ifdef CONFIG_CMD_NAND +meesc_nand_hw_init (); +#endif +meesc_ethercat_hw_init (); +#ifdef CONFIG_HAS_DATAFLASH +meesc_spi_hw_init (); +#endif +#ifdef CONFIG_MACB +meesc_macb_hw_init (); +#endif +return (0 ); +} + +int dram_init (void ) +{ + gd->bd->bi_dram[0 ].start =PHYS_SDRAM ; + gd->bd->bi_dram[0 ].size =PHYS_SDRAM_SIZE ; +return (0 ); +} + +int board_eth_init (bd_t *bis) +{ +int rc =0 ; +#ifdef CONFIG_MACB + rc =macb_eth_initialize (0 , (void *)AT91SAM9263_BASE_EMAC ,0x00 ); +#endif +return (rc); +} + +int checkboard (void ) +{ +char serno[32 ]; + +puts ("Board: esd CAN-EtherCAT Gateway\n" ); +if (getenv_r ("serial#" , serno,sizeof (serno)) >0 ) { +puts (", serial# " ); +puts (serno); + } +printf ("Hardware-revision: 1.%d\n" ,get_hw_rev ()); +return (0 ); +} + +int get_hw_rev (void ) +{ +int rev =at91_get_gpio_value (AT91_PIN_PB19 ); + rev |=at91_get_gpio_value (AT91_PIN_PB20 ) <<1 ; + rev |=at91_get_gpio_value (AT91_PIN_PB21 ) <<2 ; + rev |=at91_get_gpio_value (AT91_PIN_PB22 ) <<3 ; + +if (rev ==15 ) + rev =0 ; + +return (rev); +} + +int set_gpio (int argc,char *argv[],unsigned pin) +{ +int i =0 ; +if (argc >1 ) { + i = argv[1 ][0 ] =='1' ; +printf ("Setting GPIO-pin to '%d'\n" , i); +at91_set_gpio_output (pin, i); + }else +puts ("None value given!\n" ); +return (0 ); +} + +/* +* u-boot commands +*/ + +/* +* LED-functions +*/ +int do_led_1a (cmd_tbl_t *cmdtp,int flag,int argc,char *argv[]) +{ +return (set_gpio (argc, argv,LED1A )); +} +U_BOOT_CMD ( + led_1a,2 ,1 , do_led_1a, +"switch LED1A on or off" , +"\n" +);
board/esd/meesc/meesc.c line 331
Quoted 10 lines
board/esd/meesc/meesc.c new file +10
-0+ +int do_led_1b (cmd_tbl_t *cmdtp,int flag,int argc,char *argv[]) +{ +return (set_gpio (argc, argv,LED1B )); +} +U_BOOT_CMD ( + led_1b,2 ,1 , do_led_1b, +"switch LED1B on or off" , +"\n" +);
Ulf send a patch some weeks ago for this purpose
please take a look on it
Subject: [U-Boot] [PATCH 1/1] ARM: Add command to control coloured led from the console
Quoted 9 lines
board/esd/meesc/meesc.c new file +9
-0+ +/* +* USB-cable detect and ET1100 word switching +*/ +int do_usbstat (cmd_tbl_t *cmdtp,int flag,int argc,char *argv[]) +{ +at91_set_gpio_input (AT91_PIN_PA25 ,0 ); +udelay (10000 ); +if (at91_get_gpio_value (AT91_PIN_PA25 ))
board/esd/meesc/meesc.c line 350
Quoted 10 lines
board/esd/meesc/meesc.c new file +10
-0+puts ("USB Cable detected\n" ); + else + puts("USB Cable not detected\n"); +return (0 ); +} +U_BOOT_CMD ( + usbstat,2 ,1 , do_usbstat, +"print status of USB-Device Port" , +"\n" +);
IMHO it's could be a generic command
Quoted 40 lines
board/esd/meesc/meesc.c new file +40
-0+ +int do_wswitch (cmd_tbl_t *cmdtp,int flag,int argc,char *argv[]) +{ +if (get_hw_rev () ==0 ) +return (set_gpio (argc, argv,AT91_PIN_PA25 )); +else { +puts ("Not a prototype, word-switching not provided!\n" ); +return (0 ); + } +} +U_BOOT_CMD ( + wswitch,2 ,1 , do_wswitch, +"select read word on ET1100 (prototypes only)" , +"\n" +); + +/* +* CAN physical layer test +*/ +int do_cantst (cmd_tbl_t *cmdtp,int flag,int argc,char *argv[]) +{ +unsigned int error =0 ; +puts ("Toggeling Port PA13 (CANTX)... " ); +/* defines PA13 as output */ +at91_set_gpio_output (AT91_PIN_PA13 ,0 ); +/* defines PA14 as input, internal pullup */ +at91_set_gpio_input (AT91_PIN_PA14 ,1 ); + +while (!tstc () && !error) {/* wait for key press or error */ +at91_set_gpio_value (AT91_PIN_PA13 ,1 ); +if (!at91_get_gpio_value (AT91_PIN_PA14 )) + error =1 ; +at91_set_gpio_value (AT91_PIN_PA13 ,0 ); +if (at91_get_gpio_value (AT91_PIN_PA14 )) + error =1 ; + } + +if (error) +puts ("CAN error!!\n" ); +else {
board/esd/meesc/meesc.c line 400
Quoted 10 lines
board/esd/meesc/meesc.c new file +10
-0+puts ("done\n" ); +getc ();/* consume input */ + } +return (0 ); +} +U_BOOT_CMD ( + cantst,2 ,1 , do_cantst, +"toggles CANTX-Pin" , +"\n" +);
could you be more specific about all this new command and please add a readme
Quoted 35 lines
include/configs/meesc.h new file +29
-0@@ -0,0 +1,185 @@ +/* +* (C) Copyright 2007-2008 +* Stelian Pop <[email protected]> +* Lead Tech Design <www.leadtechdesign.com> +* +* (C) Copyright 2009 +* Daniel Gorsulowski <[email protected]> +* esd electronic system design gmbh <www.esd.eu> +* +* Configuation settings for the esd MEESC board. +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/
include/configs/meesc.h line 39
Quoted 10 lines
include/configs/meesc.h new file +10
-0+ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* ARM asynchronous clock */ +#define AT91_CPU_NAME "AT91SAM9263" +#define AT91_MAIN_CLOCK 16000000/* 16.0 MHz crystal */ +#define AT91_MASTER_CLOCK 100000000/* peripheral */ +#define AT91_CPU_CLOCK 200000000/* cpu */ +#define CONFIG_SYS_AT91_PLLB 0x00023f01/* PLLB settings for USB */
I'm preparing a new patch that will allow us to remove all this clock hardcoded define please wait one or two days
Quoted 51 lines
include/configs/meesc.h new file +51
-0+#define CONFIG_SYS_HZ 1000/* decrementer freq */ + +#define AT91_SLOW_CLOCK 32768/* slow clock */ + +#define CONFIG_MEESC 1/* Board is esd MEESC */ +#define CONFIG_ARM926EJS 1/* This is an ARM926EJS Core */ +#define CONFIG_AT91SAM9263 1/* It's an AT91SAM9263 SoC*/ +#undef CONFIG_USE_IRQ/* don't need IRQ/FIQ stuff */ +#define CONFIG_ENV_OVERWRITE 1/* necessary on prototypes */ +#define CONFIG_DISPLAY_BOARDINFO 1 +#define CONFIG_PREBOOT /* enable preboot variable */ + +#define CONFIG_CMDLINE_TAG 1/* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SKIP_RELOCATE_UBOOT + +/* +* Hardware drivers +*/ +#define CONFIG_ATMEL_USART 1 +#undef CONFIG_USART0 +#undef CONFIG_USART1 +#undef CONFIG_USART2 +#define CONFIG_USART3 1/* USART 3 is DBGU */ + +#define CONFIG_BOOTDELAY 3 + +/* +* BOOTP options +*/ +#define CONFIG_BOOTP_BOOTFILESIZE 1 +#define CONFIG_BOOTP_BOOTPATH 1 +#define CONFIG_BOOTP_GATEWAY 1 +#define CONFIG_BOOTP_HOSTNAME 1 + +/* +* Command line configuration. +*/ +#include <config_cmd_default.h> +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_USB + +#define CONFIG_CMD_PING 1 +#define CONFIG_CMD_DHCP 1
include/configs/meesc.h line 100
Quoted 10 lines
include/configs/meesc.h new file +10
-0+#define CONFIG_CMD_NAND 1 + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM 0x20000000 +#define PHYS_SDRAM_SIZE 0x02000000/* 32 megs */ + +/* DataFlash */ +#define CONFIG_HAS_DATAFLASH 1 +#define CONFIG_SYS_SPI_WRITE_TOUT (5000*CONFIG_SYS_HZ)
please add space before and after '*'
include/configs/meesc.h line 108
Quoted 8 lines
include/configs/meesc.h new file +8
-0+#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1 +#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000/* CS0 */ +#define AT91_SPI_CLK 15000000 +#define DATAFLASH_TCSS (0x1a << 16) +#define DATAFLASH_TCHS (0x1 << 24) + +/* NOR flash is not populated, disable it */ +#define CONFIG_SYS_NO_FLASH 1
Best Regards,
J.
PATCH 2/2 at91: Add support for esd MEESC board
In reply to Daniel GorsulowskiQuoted 5 lines · Daniel Gorsulowski
This patch adds support for MEESC board from esd gmbh. The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by Daniel Gorsulowski <[email protected]>---
please rebase your patch against
git://git.denx.de/u-boot-at91.git branch clock
Best Regards,
J.
PATCH 2/2 at91: Add support for esd MEESC board
Hi Jean-Christophe,
Quoted 4 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 3 lines · Daniel Gorsulowski
This patch adds support for MEESC board from esd gmbh. The MEESC is based on an Atmel AT91SAM9263 SoC.
Quoted 8 lines
Quoted 2 lines
Signed-off-by Daniel Gorsulowski <[email protected]>---
please rebase your patch against
git://git.denx.de/u-boot-at91.gitbranch clockBest Regards,
J.
sorry, but my board does not boot by this branch.
Followed by the bootstrapper-"RomBOOT"-prompt just some cryptical characters appear. Seems like the cpu clock is not initialized correctly. The board uses an 16.0 Mhz crystal.
I configured as followed:
/* ARM asynchronous clock */
#define AT91_CPU_NAME "AT91SAM9263"
#define AT91_MAIN_CLOCK 16000000 /* 16.0 MHz crystal */
#define CONFIG_SYS_HZ 1000 /* decrementer freq */
#define CONFIG_MEESC 1 /* Board is esd MEESC */
#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
#define CONFIG_AT91SAM9263 1 /* It's an AT91SAM9263 SoC*/
#define CONFIG_ARCH_CPU_INIT 1
...
If I build from git://git.denx.de/u-boot.git branch master after applying my patches, the board boots up correctly.
Best Regards,
Daniel
PATCH 2/2 at91: Add support for esd MEESC board
Quoted 11 lines · Daniel Gorsulowski
Hi Jean-Christophe,
Quoted 8 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 5 lines · Daniel Gorsulowski
This patch adds support for MEESC board from esd gmbh. The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by Daniel Gorsulowski <[email protected]>---
please rebase your patch against
Quoted 8 lines
Quoted 4 lines
git://git.denx.de/u-boot-at91.gitbranch clockBest Regards,
J.sorry, but my board does not boot by this branch.
Followed by the bootstrapper-"RomBOOT"-prompt just some cryptical characters appear. Seems like the cpu clock is not initialized correctly.
this code is not responsible to initialize the cpu clock it just read and calculate dynamicly the differenct at91 clocks
if this code does not work please not that linux will have the same problem so please fix you lowlevel_init or your at91bootstrap
Quoted 1 line
The board uses an 16.0 Mhz crystal.
this crystal can even be detected by cpu without specify it
Quoted 5 lines
I configured as followed:
/* ARM asynchronous clock */
#defineAT91_CPU_NAME"AT91SAM9263"
#defineAT91_MAIN_CLOCK16000000 /* 16.0 MHz crystal */
try without this define, by letting the cpu detect it
Best Regards,
J.
PATCH 1/2 at91: Improved Atmel AT45DB081 dataflash support
In reply to Daniel GorsulowskiDear Daniel Gorsulowski,
Quoted 6 lines · In message <[email protected]> you wrote:
This patch improves Atmel AT45DB081 dataflash support.
Signed-off-by Daniel Gorsulowski <[email protected]>--- drivers/mtd/dataflash.c | 7 ++++--- 1 files changed, 4 insertions(+), 3 deletions(-)
"improves" is a bit terse - in which way is it improved? Is it faster, more reliable, has smaller code, or what?
Please provide a little more description in the committ message.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de A witty saying proves nothing, but saying something pointless gets people's attention.
PATCH 1/2 at91: Improved Atmel AT45DB081 dataflash support
In reply to Daniel GorsulowskiQuoted 6 lines · Daniel Gorsulowski
This patch improves Atmel AT45DB081 dataflash support.
Signed-off-by Daniel Gorsulowski <[email protected]>--- drivers/mtd/dataflash.c | 7 ++++---1 1 files changed, 4 insertions(+), 3 deletions(-)
NACK
As precedently announce this driver is now deprecated only bug fix will be accepted
please take a look on the spi flash framework
Best Regards,
J.