Clean up Lemote Loongson 2E Support
PATCH 1/1 Clean up Lemote Loongson 2E Support
This patch eliminates magic numbers and adds accessors for memory-mapped registers. As well, it removes some inline assembly and restructures how the early printk code behaves.
--- arch/mips/include/asm/mach-lemote/loongson2e.h | 60 +++++++++++ arch/mips/lemote/lm2e/dbg_io.c | 125 ++--------------------- arch/mips/lemote/lm2e/prom.c | 10 +-- arch/mips/lemote/lm2e/reset.c | 18 ++-- 4 files changed, 82 insertions(+), 131 deletions(-) create mode 100644 arch/mips/include/asm/mach-lemote/loongson2e.h
arch/mips/include/asm/mach-lemote/loongson2e.h new file +60 -0
@@ -0,0 +1,60 @@ +/* Accessor functions for the Loongson 2E MMIO registers +* +* Copyright (c) 2009 Philippe Vachon <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ +#ifndef __ASM_MACH_LEMOTE_LOONGSON2E +#define __ASM_MACH_LEMOTE_LOONGSON2E + +#include <linux/types.h> + +/* Loongson 2E Control Registers */ +#define LS2E_REG_BASE 0x1fe00100/* start of config registers */ +#define LS2E_GENCFG_REG (LS2E_REG_BASE + 0x04) + +#define LS2E_RESET_VECTOR 0x1fc00000/* this should be obvious! */ + +/* UART address (16550 -- on the Fulong) */ +#define LS2E_UART_BASE 0x1fd003f8 + +/* Various system parameters passed from PMON */ +extern unsigned long bus_clock; +extern unsigned long cpu_clock_freq; +extern unsigned int memsize, highmemsize; + +static inline void ls2e_writeb (uint8_t value,unsigned long addr) +{ + *(volatile uint8_t *)addr = value; +} + +static inline void ls2e_writew (uint16_t value,unsigned long addr) +{ + *(volatile uint16_t *)addr = value; +} + +static inline void ls2e_writel (uint32_t value,unsigned long addr) +{ + *(volatile uint32_t *)addr = value; +} + +static inline uint8_t ls2e_readb (unsigned long addr) +{ +return *(volatile uint8_t *)addr; +} + +static inline uint16_t ls2e_readw (unsigned long addr) +{ +return *(volatile uint16_t *)addr; +} + +static inline uint32_t ls2e_readl (unsigned long addr) +{ +return *(volatile uint32_t *)addr; +} + +#endif /* __ASM_MACH_LEMOTE_LOONGSON2E */
arch/mips/lemote/lm2e/dbg_io.c +11 -114
139 lines not on this page · raw message
arch/mips/lemote/lm2e/prom.c +1 -9
@@ -18,10 +18,7 @@#include <linux/bootmem.h> #include <asm/bootinfo.h> -extern unsigned long bus_clock; -extern unsigned long cpu_clock_freq; -extern unsigned int memsize, highmemsize; -extern int putDebugChar (unsigned char byte); +#include <loongson2e.h> static int argc;/* pmon passes arguments in 32bit pointers */
@@ -90,8 +87,3 @@ do { \void __init prom_free_prom_memory (void ) { } - -void prom_putchar (char c) -{ -putDebugChar (c); -}
arch/mips/lemote/lm2e/reset.c +10 -8
@@ -7,20 +7,22 @@* Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology * Author: Fuxin Zhang, [email protected] */ +#include <linux/pm.h> +#include <linux/io.h> +#include <loongson2e.h> #include <asm/reboot.h> static void loongson2e_restart (char *command) { -#ifdef CONFIG_32BIT - *(unsigned long *)0xbfe00104 &= ~(1 <<2 ); - *(unsigned long *)0xbfe00104 |= (1 <<2 ); -#else - *(unsigned long *)0xffffffffbfe00104 &= ~(1 <<2 ); - *(unsigned long *)0xffffffffbfe00104 |= (1 <<2 ); -#endif - __asm__ __volatile__("jr\t%0" ::"r" (0xbfc00000 )); +uint32_t ctl = + (ls2e_readl ((phys_addr_t )ioremap_nocache (LS2E_GENCFG_REG ,4 )) + & ~(1 <<2 )) |1 <<2 ; + +ls2e_writel (ctl, (phys_addr_t )ioremap_nocache (LS2E_GENCFG_REG ,4 )); + + ((void (*)(void ))ioremap_nocache (LS2E_RESET_VECTOR ,4 ))(); }static void loongson2e_halt (void )
Signature · 1 line
1.6.1
Philippe Vachon <[email protected]> writes:
Hi,
Quoted 30 lines
This patch eliminates magic numbers and adds accessors for memory-mapped registers. As well, it removes some inline assembly and restructures how the early printk code behaves.
Signed-off-by Philippe Vachon <[email protected]>--- arch/mips/include/asm/mach-lemote/loongson2e.h | 60 +++++++++++ arch/mips/lemote/lm2e/dbg_io.c | 125 ++--------------------- arch/mips/lemote/lm2e/prom.c | 10 +-- arch/mips/lemote/lm2e/reset.c | 18 ++-- 4 files changed, 82 insertions(+), 131 deletions(-) create mode 100644 arch/mips/include/asm/mach-lemote/loongson2e.harch/mips/include/asm/mach-lemote/loongson2e.h new file +11
-0@@ -0,0 +1,60 @@ +/* Accessor functions for the Loongson 2E MMIO registers +* +* Copyright (c) 2009 Philippe Vachon <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ +#ifndef __ASM_MACH_LEMOTE_LOONGSON2E
arch/mips/include/asm/mach-lemote/loongson2e.h line 21
Quoted 10 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +10
-0+#define __ASM_MACH_LEMOTE_LOONGSON2E + +#include <linux/types.h> + +/* Loongson 2E Control Registers */ +#define LS2E_REG_BASE 0x1fe00100/* start of config registers */ +#define LS2E_GENCFG_REG (LS2E_REG_BASE + 0x04) + +#define LS2E_RESET_VECTOR 0x1fc00000/* this should be obvious! */ +
Theses are neither Lemote nor 2E specifics. 2E and 2F controllers are very similar (and they're similar to the bonito stuff). Why do you need a specific header instead of using the Bonito64.h header for theses constants ? And if you really want to create it, please rename all to loongson and remove lemote references as it'll work on 2F and on boards from ST.
arch/mips/include/asm/mach-lemote/loongson2e.h line 23
Quoted 2 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +2
-0+/* UART address (16550 -- on the Fulong) */ +#define LS2E_UART_BASE 0x1fd003f8
It happens to be 0x1fd003f8 but it could have been at a different address base. For instance, on 2f, depending on the board, there's 0x1ff003f8 and 0x1fd003f8 (I think there's also some board with a different address than theses but I'm not sure).
arch/mips/include/asm/mach-lemote/loongson2e.h line 34
Quoted 10 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +10
-0+/* Various system parameters passed from PMON */ +extern unsigned long bus_clock; +extern unsigned long cpu_clock_freq; +extern unsigned int memsize, highmemsize; + +static inline void ls2e_writeb (uint8_t value,unsigned long addr) +{ + *(volatile uint8_t *)addr = value; +} +
What about readl/writel and friends ?
[...]
arch/mips/include/asm/mach-lemote/loongson2e.h
Quoted 10 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +4
-5-void debugInit (u32 baud,u8 data,u8 parity,u8 stop) +void prom_putchar (char c) { -u32 divisor; - -/* disable interrupts */ -UART16550_WRITE (OFS_INTR_ENABLE ,0 ); +int timeout; +phys_addr_t uart_base = (phys_addr_t )ioremap_nocache (LS2E_UART_BASE ,8 ); +char reg =ls2e_readb (uart_base +UART_LSR ) &UART_LSR_THRE ;
hmm... I may be wrong on that but using ioremap looks here looks not a good idea. This code is called by early_printk so you can end up calling it very early in the boot process.
Also, you're calling ioremap everytime this function is called. Why don't you do that only the first time ?
[...]
Quoted 22 lines
arch/mips/lemote/lm2e/reset.c +3
-5@@ -7,20 +7,22 @@* Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology * Author: Fuxin Zhang, [email protected] */ +#include <linux/pm.h> +#include <linux/io.h> +#include <loongson2e.h> #include <asm/reboot.h> static void loongson2e_restart (char *command) { -#ifdef CONFIG_32BIT - *(unsigned long *)0xbfe00104 &= ~(1 <<2 ); - *(unsigned long *)0xbfe00104 |= (1 <<2 ); -#else - *(unsigned long *)0xffffffffbfe00104 &= ~(1 <<2 );
arch/mips/lemote/lm2e/reset.c line 25
Quoted 10 lines
arch/mips/lemote/lm2e/reset.c +7
-3- *(unsigned long *)0xffffffffbfe00104 |= (1 <<2 ); -#endif - __asm__ __volatile__("jr\t%0" ::"r" (0xbfc00000 )); +uint32_t ctl = + (ls2e_readl ((phys_addr_t )ioremap_nocache (LS2E_GENCFG_REG ,4 )) + & ~(1 <<2 )) |1 <<2 ; + +ls2e_writel (ctl, (phys_addr_t )ioremap_nocache (LS2E_GENCFG_REG ,4 )); + + ((void (*)(void ))ioremap_nocache (LS2E_RESET_VECTOR ,4 ))();
same remark as for the serial stuff. I'm really not sure that calling ioremap in such a place is a good idea (say, you've panic'ed and booted with panic=3, will this still work ?).
Arnaud
Quoted 43 lines · Arnaud Patard
Philippe Vachon <[email protected]> writes:
Hi,
Quoted 39 lines
This patch eliminates magic numbers and adds accessors for memory-mapped registers. As well, it removes some inline assembly and restructures how the early printk code behaves.
Signed-off-by Philippe Vachon <[email protected]>--- arch/mips/include/asm/mach-lemote/loongson2e.h | 60 +++++++++++ arch/mips/lemote/lm2e/dbg_io.c | 125 ++--------------------- arch/mips/lemote/lm2e/prom.c | 10 +-- arch/mips/lemote/lm2e/reset.c | 18 ++-- 4 files changed, 82 insertions(+), 131 deletions(-) create mode 100644 arch/mips/include/asm/mach-lemote/loongson2e.harch/mips/include/asm/mach-lemote/loongson2e.h new file +20
-0@@ -0,0 +1,60 @@ +/* Accessor functions for the Loongson 2E MMIO registers +* +* Copyright (c) 2009 Philippe Vachon <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ +#ifndef __ASM_MACH_LEMOTE_LOONGSON2E +#define __ASM_MACH_LEMOTE_LOONGSON2E + +#include <linux/types.h> + +/* Loongson 2E Control Registers */ +#define LS2E_REG_BASE 0x1fe00100/* start of config registers */ +#define LS2E_GENCFG_REG (LS2E_REG_BASE + 0x04) + +#define LS2E_RESET_VECTOR 0x1fc00000/* this should be obvious! */
Quoted 9 lines
arch/mips/include/asm/mach-lemote/loongson2e.h line 21
Quoted 1 line
arch/mips/include/asm/mach-lemote/loongson2e.h new file +1
-0+Theses are neither Lemote nor 2E specifics. 2E and 2F controllers are very similar (and they're similar to the bonito stuff). Why do you need a specific header instead of using the
Bonito64.hheader for theses constants ? And if you really want to create it, please rename all to loongson and remove lemote references as it'll work on 2F and on boards from ST.
I am working on merging the source code of fuloong+yeeloong(2f based) and 2e, currently, the source code of fuloong & yeeloong have been merged, and now, I am trying to merge 2e & 2f, lots of duplications have been removed with the import of some new header files, and some MACROs, Variables have been tuned. a first release may be out to dev.lemote.com before this weekend.
Quoted 8 lines
arch/mips/include/asm/mach-lemote/loongson2e.h line 23
Quoted 2 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +2
-0+/* UART address (16550 -- on the Fulong) */ +#define LS2E_UART_BASE 0x1fd003f8It happens to be
0x1fd003f8but it could have been at a different address base. For instance, on 2f, depending on the board, there's0x1ff003f8and0x1fd003f8(I think there's also some board with a different address than theses but I'm not sure).
in fuloong(2f) & yeeloong(2f), the serial address is 0xbfd002f8, in fuloong(2e), the serial address is 0xbfd003f8.
Quoted 73 lines
arch/mips/include/asm/mach-lemote/loongson2e.h line 34
Quoted 10 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +10
-0+/* Various system parameters passed from PMON */ +extern unsigned long bus_clock; +extern unsigned long cpu_clock_freq; +extern unsigned int memsize, highmemsize; + +static inline void ls2e_writeb (uint8_t value,unsigned long addr) +{ + *(volatile uint8_t *)addr = value; +} +What about readl/writel and friends ?
[...]arch/mips/include/asm/mach-lemote/loongson2e.h
Quoted 10 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +4
-5-void debugInit (u32 baud,u8 data,u8 parity,u8 stop) +void prom_putchar (char c) { -u32 divisor; - -/* disable interrupts */ -UART16550_WRITE (OFS_INTR_ENABLE ,0 ); +int timeout; +phys_addr_t uart_base = (phys_addr_t )ioremap_nocache (LS2E_UART_BASE ,8 ); +char reg =ls2e_readb (uart_base +UART_LSR ) &UART_LSR_THRE ;hmm... I may be wrong on that but using ioremap looks here looks not a good idea. This code is called by
early_printkso you can end up calling it very early in the boot process.
Also, you're calling ioremap everytime this function is called. Why don't you do that only the first time ?[...]
Quoted 22 lines
arch/mips/lemote/lm2e/reset.c +3
-5@@ -7,20 +7,22 @@* Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology * Author: Fuxin Zhang, [email protected] */ +#include <linux/pm.h> +#include <linux/io.h> +#include <loongson2e.h> #include <asm/reboot.h> static void loongson2e_restart (char *command) { -#ifdef CONFIG_32BIT - *(unsigned long *)0xbfe00104 &= ~(1 <<2 ); - *(unsigned long *)0xbfe00104 |= (1 <<2 ); -#else - *(unsigned long *)0xffffffffbfe00104 &= ~(1 <<2 );arch/mips/lemote/lm2e/reset.c line 25
Quoted 10 lines
arch/mips/lemote/lm2e/reset.c +7
-3- *(unsigned long *)0xffffffffbfe00104 |= (1 <<2 ); -#endif - __asm__ __volatile__("jr\t%0" ::"r" (0xbfc00000 )); +uint32_t ctl = + (ls2e_readl ((phys_addr_t )ioremap_nocache (LS2E_GENCFG_REG ,4 )) + & ~(1 <<2 )) |1 <<2 ; + +ls2e_writel (ctl, (phys_addr_t )ioremap_nocache (LS2E_GENCFG_REG ,4 )); + + ((void (*)(void ))ioremap_nocache (LS2E_RESET_VECTOR ,4 ))();same remark as for the serial stuff. I'm really not sure that calling ioremap in such a place is a good idea (say, you've panic'ed and booted with panic=3, will this still work ?).
Arnaud
Hi,
Quoted 8 lines · Arnaud Patard
Theses are neither Lemote nor 2E specifics. 2E and 2F controllers are very similar (and they're similar to the bonito stuff). Why do you need a specific header instead of using the
Bonito64.hheader for theses constants ? And if you really want to create it, please rename all to loongson and remove lemote references as it'll work on 2F and on boards from ST.
What might be worthwhile eventually is to move all the loongson code into arch/mips/loongson. I know there is some duplication of code between 2F and 2E as it stands, but since 2F isn't upstream yet (and probably won't be for a while), I would cross that bridge when we get there.
Given how Loongson actually differs a lot from Bonito64 beyond a few of the control registers' addresses, perhaps it is worthwhile to start moving away from using bonito64.h anyways; it's a bit odd that ICT chose to base some of the SoC on the Bonito64 design, IMO, but that's a different conversation.
Quoted 8 lines
arch/mips/include/asm/mach-lemote/loongson2e.h line 23
Quoted 2 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +2
-0+/* UART address (16550 -- on the Fulong) */ +#define LS2E_UART_BASE 0x1fd003f8It happens to be
0x1fd003f8but it could have been at a different address base. For instance, on 2f, depending on the board, there's0x1ff003f8and0x1fd003f8(I think there's also some board with a different address than theses but I'm not sure).
One option I was thinking of was moving that into a device-specific header. However, of the two Loongson 2E devices I have, both have the UART at the same address -- are there any Loongson 2E devices that have the UART at a different location? None that I'm aware of (and on the 2F side, I only know of the Gdium).
...
Quoted 8 lines
arch/mips/include/asm/mach-lemote/loongson2e.h line 34
Quoted 5 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +5
-0+static inline void ls2e_writeb (uint8_t value,unsigned long addr) +{ + *(volatile uint8_t *)addr = value; +} +What about readl/writel and friends ?
I'm ambivalent. Since they're sub-64-bit-wide reads/writes, they're happening in a single instruction anyways. I can adjust the patch to use them in the name of reducing code duplication.
Quoted 7 lines
hmm... I may be wrong on that but using ioremap looks here looks not a good idea. This code is called by
early_printkso you can end up calling it very early in the boot process.
Also, you're calling ioremap everytime this function is called. Why don't you do that only the first time ?[...]
Quite wrong -- as the address is in kseg1, when compiled this actually will end up having the same net effect as using the 'deprecated' CKSEG1ADDR() macro. Have a look at the implementation of __ioremap_mode() in arch/mips/include/asm/io.h. While it's being 'called' early in the boot process, the physical resource will be accessed via its kseg1 address. When I was speaking to Ralf about this, he had mentioned this was by design.
In looking at the disassembly of prom_putchar in particular:
; ioremap_nocache()
li $v0, 0xFFFFFFF9 dsll32 $v0, 8 ori $v0, 0x1FD dsll $v0, 20 ori $v0, 0x3FD
; load from the UART's LSR register:
lbu $v1, 0($v0)
...
Quoted 4 lines
same remark as for the serial stuff. I'm really not sure that calling ioremap in such a place is a good idea (say, you've panic'ed and booted with panic=3, will this still work ?).
Yes. See above.
I'll probably send an updated patch shortly.
Cheers,
Phil
Philippe Vachon <[email protected]> writes:
Hi,
Quoted 12 lines
Hi,
Quoted 8 lines · Arnaud Patard
Theses are neither Lemote nor 2E specifics. 2E and 2F controllers are very similar (and they're similar to the bonito stuff). Why do you need a specific header instead of using the
Bonito64.hheader for theses constants ? And if you really want to create it, please rename all to loongson and remove lemote references as it'll work on 2F and on boards from ST.
Quoted 4 lines
What might be worthwhile eventually is to move all the loongson code into
arch/mips/loongson. I know there is some duplication of code between 2F and 2E as it stands, but since 2F isn't upstream yet (and probably won't be for a while), I would cross that bridge when we get there.
That's not a good reason to repeat wrong naming from the past. Moverover, Lemote is trying to get 2f support merged so I would say that you're pessimistic.
Quoted 16 lines
Given how Loongson actually differs a lot from Bonito64 beyond a few of the control registers' addresses, perhaps it is worthwhile to start moving away from using
bonito64.hanyways; it's a bit odd that ICT chose to base some of the SoC on the Bonito64 design, IMO, but that's a different conversation.Quoted 8 lines
arch/mips/include/asm/mach-lemote/loongson2e.h line 23
Quoted 2 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +2
-0+/* UART address (16550 -- on the Fulong) */ +#define LS2E_UART_BASE 0x1fd003f8It happens to be
0x1fd003f8but it could have been at a different address base. For instance, on 2f, depending on the board, there's0x1ff003f8and0x1fd003f8(I think there's also some board with a different address than theses but I'm not sure).
Quoted 5 lines
One option I was thinking of was moving that into a device-specific header. However, of the two Loongson 2E devices I have, both have the UART at the same address -- are there any Loongson 2E devices that have the UART at a different location? None that I'm aware of (and on the 2F side, I only know of the Gdium).
1 is more than 0 so, please take 2f into account. I don't see the benefit of creating yet an other header containing only difference something like "UART_BASE 0x1ff003f8"
Quoted 24 lines
...
Quoted 8 lines
arch/mips/include/asm/mach-lemote/loongson2e.h line 34
Quoted 5 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +5
-0+static inline void ls2e_writeb (uint8_t value,unsigned long addr) +{ + *(volatile uint8_t *)addr = value; +} +What about readl/writel and friends ?
I'm ambivalent. Since they're sub-64-bit-wide reads/writes, they're happening in a single instruction anyways. I can adjust the patch to use them in the name of reducing code duplication.
Quoted 7 lines
hmm... I may be wrong on that but using ioremap looks here looks not a good idea. This code is called by
early_printkso you can end up calling it very early in the boot process.
Also, you're calling ioremap everytime this function is called. Why don't you do that only the first time ?[...]
Quoted 7 lines
Quite wrong -- as the address is in kseg1, when compiled this actually will end up having the same net effect as using the 'deprecated'
CKSEG1ADDR()macro. Have a look at the implementation of__ioremap_mode()inarch/mips/include/asm/io.h. While it's being 'called' early in the boot process, the physical resource will be accessed via its kseg1 address. When I was speaking to Ralf about this, he had mentioned this was by design.
ok, I read the code too quickly. thanks.
Please note also that my remark about calling it everytime still stands. Reading a variable is taking less instructions than calling ioremap_nocache.
Arnaud
Hi,
Please refer to this mess --
http://lebesgue.cowpig.ca/~philippe/gdium/0001-Clean-up-Lemote-Loongson-2-Support.patch -- for my subsequent commentary. This is what I would envision being moved upstream eventually, and how I think Loongson support would eventually best be structured. This adds basic support for the Emtec Gdium as well as the Fulong. I created a special case for the Menglan, but it doesn't do anything particularily different from the Fulong other than change what
the machine name is in /proc/cpuinfo.
I've been working on this with the following goals in mind:
- Determine what functionality is specific to a particular platform and split it off elsewhere.
- Build up a directory of code common to the Loongson 2 "series" of CPUs.
- Attempt to move away from anything using CKSEG1ADDR(); this is far from complete. Ralf will gut me if I try to submit a patch using CKSEG1ADDR().
- Attempt to unify the Loongson 2E/F register names in their own header. One thing I've noticed is that where there was a Bonito register it would be used -- otherwise, the 'raw' number would be cast to a pointer and dereferenced!
- Try to build a framework on which a new Loongson 2E/2F/2G(?) machines could be added quickly. I actually did that with the Gdium, borrowing some of the existing code Mandriva and Lemote have done for it.
Of course, at a glance you'll see it's far from being ready to be submitted upstream -- and I need to do a rebase or two to make it a little more pallatable, given the size of the patch.
I've laid out the directories as follows:
arch/mips/
+- loongson/ | +- common/ /* common code */ | +- gdium/ /* all the other directories are for */ | +- fulong-2e /* particular platforms */ | ... +- include/asm/ +- mach-loongson/ /* platform-specific headers */ +- fulong-2e/ +- gdium/
Quoted 4 lines · Arnaud Patard
That's not a good reason to repeat wrong naming from the past. Moverover, Lemote is trying to get 2f support merged so I would say that you're pessimistic.
Generally, the purpose of this patch was to clean up some ugliness I saw when I was trying to help someone figure out why they were having trouble with kernels they were building. I didn't want to set out to do something too invasive, as that would just lead to headaches for everyone.
I don't mean to come off as pessimistic, either -- I'm quite excited that Lemote is trying to move things up-stream. I do recognize how much work it is to move a gargantuan patch like that upstream, however, and I didn't want to get in the way of that.
Quoted 22 lines
Quoted 16 lines
Given how Loongson actually differs a lot from Bonito64 beyond a few of the control registers' addresses, perhaps it is worthwhile to start moving away from using
bonito64.hanyways; it's a bit odd that ICT chose to base some of the SoC on the Bonito64 design, IMO, but that's a different conversation.Quoted 8 lines
arch/mips/include/asm/mach-lemote/loongson2e.h line 23
Quoted 2 lines
arch/mips/include/asm/mach-lemote/loongson2e.h new file +2
-0+/* UART address (16550 -- on the Fulong) */ +#define LS2E_UART_BASE 0x1fd003f8It happens to be
0x1fd003f8but it could have been at a different address base. For instance, on 2f, depending on the board, there's0x1ff003f8and0x1fd003f8(I think there's also some board with a different address than theses but I'm not sure).Quoted 5 lines
One option I was thinking of was moving that into a device-specific header. However, of the two Loongson 2E devices I have, both have the UART at the same address -- are there any Loongson 2E devices that have the UART at a different location? None that I'm aware of (and on the 2F side, I only know of the Gdium).
Quoted 3 lines
1 is more than 0 so, please take 2f into account. I don't see the benefit of creating yet an other header containing only difference something like "
UART_BASE0x1ff003f8"
See my above proposed patch. Since there are definitely cases where there will be code that will be reused (plus-or-minus an address or two), building a mechanism that allows easy reuse of this code makes sense in my mind.
They way I'd propose implementing this (and is how I implemented it in the above patch) is a per-unique-platform header. This would contain certain values that might change depending on the platform (i.e. the UART base address, machine name, etc.). It'd actually be nice to be able to detect which of these paramters should be used during boot, but as far as I know there's no universal mechanism to do this (for example, Cisco hardware of the same series have board registers that contain a device identifier).
Quoted 5 lines
ok, I read the code too quickly. thanks.
Please note also that my remark about calling it everytime still stands. Reading a variable is taking less instructions than calling
ioremap_nocache.
I'm not entirely sure I agree with you. While there is an overhead incurred by using ioremap() on each character for prom_putc(), that overhead is likely amortized by the fact you're waiting for the 8250-compatible's transmit buffer to clear. Those 5-6 instructions are nothing compared to that!
Thanks for your comments, I'll try to take some of your ideas and integrate them back into what I've been working on.
Cheers,
Phil
Quoted 7 lines · Philippe Vachon
I've laid out the directories as follows:
arch/mips/+- loongson/ | +- common/ /* common code */ | +- gdium/ /* all the other directories are for */ | +- fulong-2e /* particular platforms */
Hi, Philippe,
Sorry for nitpicking, but fulong actually was a typo which slipped in somehow. The correct English name should be fuloong as shown here:
http://www.lemote.com/english/fuloong.html
Also please take a look at this:
http://www.linux-mips.org/archives/linux-mips/2009-03/msg00225.html
BTW, Thank you for hard work on this. I really hope loongson 2f's code would be merged soon, and have all the loongson related code sorted out.
Quoted 8 lines
| ... +- include/asm/ +- mach-loongson/ /* platform-specific headers */ +- fulong-2e/ +- gdium/
Signature · 4 lines
Zhang, Le Gentoo/Loongson Developer http://zhangle.is-a-geek.org 0260 C902 B8F8 6506 6586 2B90 BC51 C808 1E4E 2973