FM1216ME_MK3 some changes
PATCH 1/1 FM1216ME_MK3 some changes
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
2. Set correct highest freq of the higher band.
3. Set charge pump bit
linux/drivers/media/common/tuners/tuner-types.c +3 -3
@@ -557,9 +557,9 @@/* ------------ TUNER_PHILIPS_FM1216ME_MK3 - Philips PAL ------------ */ static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { - {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *158.00 /*MHz*/ ,0xc6 ,0x01 , }, + {16 *441.00 /*MHz*/ ,0xc6 ,0x02 , }, + {16 *864.00 ,0xc6 ,0x04 , }, };
With my best regards, Dmitry.
linux/drivers/media/common/tuners/tuner-types.c +3 -3
@@ -557,9 +557,9 @@/* ------------ TUNER_PHILIPS_FM1216ME_MK3 - Philips PAL ------------ */ static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { - {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *158.00 /*MHz*/ ,0xc6 ,0x01 , }, + {16 *441.00 /*MHz*/ ,0xc6 ,0x02 , }, + {16 *864.00 ,0xc6 ,0x04 , }, };
--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
Dmitri,
Quoted 4 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
This concerns me slightly as it does not match the datasheet (hence the design objectives) of the FM1236ME_MK3.
How are you measuring sensitivity? Do you know if it really is the middle-band preselector filter (and PLL and Mixer) or is it a problem with the input signal? How do you know it is not manufacturing variations in the preselector filters with the particular tuner assembly you are testing?
Also, as an alternative to using a different frequency for the bandswitch, have you considered setting the Auxillary Byte in the tuner chip (Infineon TUA6030?) to use external AGC and experimented with changing the tuner AGC take-over point (TOP) in the TDA9887?
By maximizing the gain in the tuner chip, but avoiding clipping, with the proper TOP setting, you minimize the contributions by the rest of the receive chain to the overall receiver Noise Figure:
http://en.wikipedia.org/wiki/Friis_formulas_for_noise
This may be a way to improve receiver sensitivity that does not conflict with the data sheet specification.
Quoted 1 line
2. Set correct highest freq of the higher band.
:)
This bothers me too; all the tuners in tuner-types.c have it set too high (999.0 MHz). I think I rememeber at time when all the tuner_range definitions had a real value there.
It would be nice to have a real value there for all the tuners. The function tuner-simple.c:simple_config_lookup() would then prevent attempts to tune to an unsupported frequnecy.
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the FM1236ME_MK3 datasheet:
"It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)
Regards,
Andy
Quoted 24 lines
diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-types.clinux/drivers/media/common/tuners/tuner-types.c +3
-3@@ -557,9 +557,9 @@/* ------------ TUNER_PHILIPS_FM1216ME_MK3 - Philips PAL ------------ */ static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { - {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *158.00 /*MHz*/ ,0xc6 ,0x01 , }, + {16 *441.00 /*MHz*/ ,0xc6 ,0x02 , }, + {16 *864.00 ,0xc6 ,0x04 , }, };Signed-off-by Beholder Intl. Ltd. Dmitry Belimov <[email protected]>With my best regards, Dmitry.
--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
Hi Andy and Dmitry,
Am Mittwoch, den 22.04.2009, 22:08 -0400 schrieb Andy Walls:
Quoted 8 lines
Dmitri,
Quoted 4 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
first of all, Dmitry, you need to send all your patches, also the prior ones, to [email protected]. Only there "patchwork" will parse for them and you might eventually find them here.
http://patchwork.kernel.org/project/linux-media/list
http://patchwork.kernel.org/project/linux-media/list/?state=*
You seem to have missed that completely and thanks to Andy to start to comment on this one, even only on video4linux previously.
Quoted 8 lines
This concerns me slightly as it does not match the datasheet (hence the design objectives) of the
FM1236ME_MK3.How are you measuring sensitivity? Do you know if it really is the middle-band preselector filter (and PLL and Mixer) or is it a problem with the input signal? How do you know it is not manufacturing variations in the preselector filters with the particular tuner assembly you are testing?
I did not look into the datasheet again, we did not have it at all for a very long time, but we had a similar case already and that time we made the decision like it can be found in this thread. No complaints ever until today.
http://marc.info/?l=linux-video&m=112639247330257&w=2
Did not look up all frequency tables again, but if it is the same again, I would say the risk of doing something wrong is close to zero.
For the rest I never noticed any difference and we have it on lots of other tuners like that. And, that one still means a lot of _different_ tuners and different manufacturers, filters definitely differ! ...
Quoted 65 lines
Also, as an alternative to using a different frequency for the bandswitch, have you considered setting the Auxillary Byte in the tuner chip (Infineon TUA6030?) to use external AGC and experimented with changing the tuner AGC take-over point (TOP) in the TDA9887?
By maximizing the gain in the tuner chip, but avoiding clipping, with the proper TOP setting, you minimize the contributions by the rest of the receive chain to the overall receiver Noise Figure:
http://en.wikipedia.org/wiki/Friis_formulas_for_noise
This may be a way to improve receiver sensitivity that does not conflict with the data sheet specification.
Quoted 1 line
2. Set correct highest freq of the higher band.
:)
This bothers me too; all the tuners in
tuner-types.chave it set too high (999.0 MHz). I think I rememeber at time when all thetuner_rangedefinitions had a real value there.It would be nice to have a real value there for all the tuners. The function tuner-simple.c:simple_config_lookup() would then prevent attempts to tune to an unsupported frequnecy.
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet:
"It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Regards,
AndyQuoted 17 lines
diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-types.clinux/drivers/media/common/tuners/tuner-types.c +3
-3@@ -557,9 +557,9 @@/* ------------ TUNER_PHILIPS_FM1216ME_MK3 - Philips PAL ------------ */ static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { - {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *158.00 /*MHz*/ ,0xc6 ,0x01 , }, + {16 *441.00 /*MHz*/ ,0xc6 ,0x02 , }, + {16 *864.00 ,0xc6 ,0x04 , }, };
Quoted 3 lines
Quoted 3 lines
Signed-off-by Beholder Intl. Ltd. Dmitry Belimov <[email protected]>With my best regards, Dmitry.
Cheers,
Hermann
Hi Andy
Quoted 4 lines
Dmitri,
On Wed, 2009-04-22 at 17:48 +1000, Dmitri Belimov wrote:
Quoted 8 lines
Quoted 5 lines
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
This concerns me slightly as it does not match the datasheet (hence the design objectives) of the
FM1236ME_MK3.
Yes, I know.
Quoted 5 lines
How are you measuring sensitivity? Do you know if it really is the middle-band preselector filter (and PLL and Mixer) or is it a problem with the input signal? How do you know it is not manufacturing variations in the preselector filters with the particular tuner assembly you are testing?
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
Quoted 31 lines
Also, as an alternative to using a different frequency for the bandswitch, have you considered setting the Auxillary Byte in the tuner chip (Infineon TUA6030?) to use external AGC and experimented with changing the tuner AGC take-over point (TOP) in the TDA9887?
By maximizing the gain in the tuner chip, but avoiding clipping, with the proper TOP setting, you minimize the contributions by the rest of the receive chain to the overall receiver Noise Figure:
http://en.wikipedia.org/wiki/Friis_formulas_for_noise
This may be a way to improve receiver sensitivity that does not conflict with the data sheet specification.
Quoted 1 line
2. Set correct highest freq of the higher band.
:)
This bothers me too; all the tuners in
tuner-types.chave it set too high (999.0 MHz). I think I rememeber at time when all thetuner_rangedefinitions had a real value there.It would be nice to have a real value there for all the tuners. The function tuner-simple.c:simple_config_lookup() would then prevent attempts to tune to an unsupported frequnecy.
Quoted 7 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem. But in digital TV mode noise from PLL decreased BER.
Quoted 5 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet:
"It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)
Yes. You are right. We can swith CP off in FM mode.
With my best regards, Dmitry.
Quoted 31 lines
Regards,
AndyQuoted 26 lines
diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-types.c
---a/linux/drivers/media/common/tuners/tuner-types.cTueJan 27 23:47:50 2009 -0200 +++
b/linux/drivers/media/common/tuners/tuner-types.cTue Apr 21
09:44:38 2009 +1000 @@ -557,9 +557,9 @@ /* ------------TUNER_PHILIPS_FM1216ME_MK3- Philips PAL ------------ */
static structtuner_rangetuner_fm1216me_mk3_pal_ranges[] = {linux/drivers/media/common/tuners/tuner-types.c +3
-3- { 16 * 158.00 /*MHz*/, 0x8e, 0x01, }, - { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 158.00 /*MHz*/, 0xc6, 0x01, }, + { 16 * 441.00 /*MHz*/, 0xc6, 0x02, }, + { 16 * 864.00 , 0xc6, 0x04, }, };Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov
<[email protected]>With my best regards, Dmitry.
--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 13 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Quoted 8 lines
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at tveeprom.c, a number of other tuners are using that tuner definition:
$ grep FM1216ME_MK3 tveeprom.c
{ TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"},
{ TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"},
{ TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"},
{ TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"},
{ TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"},
{ TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"},
{ TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"},
{ TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the FM1216ME_MK3 defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.
Quoted 10 lines
Quoted 7 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.
I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 7 lines
Quoted 5 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet:
"It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
Andy
Hi,
Am Donnerstag, den 23.04.2009, 21:43 -0400 schrieb Andy Walls:
Quoted 70 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 13 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Quoted 8 lines
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 10 lines
Quoted 7 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 5 lines
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
that is for sure, analog only.
Dmitry is preparing something for the MK5 too and the FMD1216ME/I MK3 hybrid. Hmm, I wonder if Hans and Jarod do have something to improve for the MK4 too and the others.
As said, I don't care for changes within the freq. gap and accept everything working better there ;)
Quoted 9 lines
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet:
"It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
Quoted 8 lines
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
Andy
Cheers,
Hermann
If it should be unnoticed yet.
Quoted 4 lines
Quoted 3 lines
I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
that is for sure, analog only.
Dmitry is preparing something for the MK5 too and the FMD1216ME/I MK3 hybrid. Hmm, I wonder if Hans and Jarod do have something to improve for the MK4 too and the others.
As said, I don't care for changes within the freq. gap and accept everything working better there ;)
For some sort of completeness, we have quite some cardbus devices too, originally hacked by Hans J. Koch, you might not recognize as MK3 stuff.
They come as ancient ALPS stuff.
Cheers,
Hermann
Hi Andy
Quoted 25 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 7 lines
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
;-)
Quoted 16 lines
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},
Quoted 4 lines
If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.
We can make fake FM1216ME_MK3 compatible tuner for clones. And move clones to it. After testing each clone with real compatibility with FM1216ME_MK3 we can move to real tuner.
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 7 lines
Quoted 2 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Ok. I'll discuss about it with our system programmer.
Quoted 5 lines
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Yes, you are right. This solutions used for hybrid tuners too.
Quoted 8 lines
Quoted 7 lines
Quoted 5 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3
datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
Quoted 7 lines
OK. Thank you.
Quoted 1 line
Regards,
Andy
With my best regards, Dmitry.
Hi,
Am Sonntag, den 26.04.2009, 23:58 +1000 schrieb Dmitri Belimov:
Quoted 53 lines
Hi Andy
Quoted 25 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 7 lines
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
;-)
Quoted 16 lines
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},
Quoted 18 lines
Quoted 4 lines
If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.We can make fake
FM1216ME_MK3compatible tuner for clones. And move clones to it. After testing each clone with real compatibility withFM1216ME_MK3we can move to real tuner.Quoted 10 lines
Quoted 10 lines
Quoted 7 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
Some confusion probably started here.
You were talking about one more different tuner ...
Quoted 28 lines
Quoted 4 lines
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Ok. I'll discuss about it with our system programmer.
Quoted 5 lines
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Yes, you are right. This solutions used for hybrid tuners too.
Quoted 13 lines
Quoted 7 lines
Quoted 5 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3
datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
Quoted 5 lines
Quoted 2 lines
Regards,
AndyWith my best regards, Dmitry.
--
Cheers,
Hermann
Hi All
Step by step.
This is patch for change only range of FM1216ME_MK3. Slow tunning is not a big problem.
linux/drivers/media/common/tuners/tuner-types.c +2 -2
@@ -558,8 +558,8 @@static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *441.00 /*MHz*/ ,0x8e ,0x02 , }, + {16 *864.00 ,0x8e ,0x04 , }, };static struct tuner_params tuner_fm1216me_mk3_params[] = {
With my best regards, Dmitry.
Quoted 88 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 10 lines
Quoted 7 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 7 lines
Quoted 5 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3
datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
Quoted 10 lines
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
Andy
linux/drivers/media/common/tuners/tuner-types.c +2 -2
@@ -558,8 +558,8 @@static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *441.00 /*MHz*/ ,0x8e ,0x02 , }, + {16 *864.00 ,0x8e ,0x04 , }, };static struct tuner_params tuner_fm1216me_mk3_params[] = {
hermann pitton
Acked-byHi,
Am Montag, den 27.04.2009, 19:29 +1000 schrieb Dmitri Belimov:
Quoted 21 lines
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.clinux/drivers/media/common/tuners/tuner-types.c +2
-2@@ -558,8 +558,8 @@static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *441.00 /*MHz*/ ,0x8e ,0x02 , }, + {16 *864.00 ,0x8e ,0x04 , }, };static struct tuner_params tuner_fm1216me_mk3_params[] = {
Quoted 1 line
Signed-off-by Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
if it does help anything for having all above 441 MHz in UHF ranges.
There is simply no known broadcast in that gap on other freq. tables.
Can you please enlighten us who/what broadcasts there?
Quoted 4 lines
With my best regards, Dmitry.
Quoted 1 line
Hi Dmitri,
Cheers,
Hermann
Quoted 96 lines
Quoted 96 lines
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 10 lines
Quoted 7 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 7 lines
Quoted 5 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3
datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
Andy
Am Dienstag, den 28.04.2009, 02:11 +0200 schrieb hermann pitton:
Quoted 22 lines
Hi,
Am Montag, den 27.04.2009, 19:29 +1000 schrieb Dmitri Belimov:
Quoted 19 lines
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.clinux/drivers/media/common/tuners/tuner-types.c +2
-2@@ -558,8 +558,8 @@static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *441.00 /*MHz*/ ,0x8e ,0x02 , }, + {16 *864.00 ,0x8e ,0x04 , }, };
Quoted 5 lines
Quoted 3 lines
linux/drivers/media/common/tuners/tuner-types.c +0
-0static struct tuner_params tuner_fm1216me_mk3_params[] = {Signed-off-by Beholder Intl. Ltd. Dmitry Belimov <[email protected]>if it does help anything for having all above 441 MHz in UHF ranges.
for the record: from 441 MHz on ...
Quoted 115 lines
Acked-by Hermann Pitton <[email protected]>There is simply no known broadcast in that gap on other freq. tables.
Can you please enlighten us who/what broadcasts there?
Quoted 4 lines
With my best regards, Dmitry.
Quoted 1 line
Hi Dmitri,
Cheers,
HermannQuoted 88 lines
Quoted 88 lines
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 10 lines
Quoted 7 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 7 lines
Quoted 5 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3
datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 8 lines
Quoted 8 lines
Quoted 1 line
With my best regards, Dmitry.
Regards,
Andy--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi,
Quoted 28 lines
Am Montag, den 27.04.2009, 19:29 +1000 schrieb Dmitri Belimov:
Quoted 22 lines
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c
---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++
b/linux/drivers/media/common/tuners/tuner-types.cTue Apr 28
03:35:42 2009 +1000 @@ -558,8 +558,8 @@
static structtuner_rangetuner_fm1216me_mk3_pal_ranges[] = {linux/drivers/media/common/tuners/tuner-types.c +2
-2{ 16 * 158.00 /*MHz*/, 0x8e, 0x01, }, - { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 2 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov
<[email protected]>if it does help anything for having all above 441 MHz in UHF ranges.
Quoted 5 lines
Acked-by Hermann Pitton <[email protected]>There is simply no known broadcast in that gap on other freq. tables.
Can you please enlighten us who/what broadcasts there?
I don't know. This trick for solve problem with low sensitivity the tuners on end of band. We get it from measuments.
Quoted 7 lines
Quoted 4 lines
With my best regards, Dmitry.
Quoted 1 line
Hi Dmitri,
Cheers,
Hermann
With my best regards, Dmitry.
Quoted 101 lines
Quoted 100 lines
Quoted 100 lines
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 11 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
Andy
Hi,
Am Montag, den 27.04.2009, 20:42 +1000 schrieb Dmitri Belimov:
Quoted 30 lines
Hi,
Quoted 28 lines
Am Montag, den 27.04.2009, 19:29 +1000 schrieb Dmitri Belimov:
Quoted 22 lines
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c
---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++
b/linux/drivers/media/common/tuners/tuner-types.cTue Apr 28
03:35:42 2009 +1000 @@ -558,8 +558,8 @@
static structtuner_rangetuner_fm1216me_mk3_pal_ranges[] = {linux/drivers/media/common/tuners/tuner-types.c +2
-2{ 16 * 158.00 /*MHz*/, 0x8e, 0x01, }, - { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 2 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov
<[email protected]>if it does help anything for having all above 441 MHz in UHF ranges.
Quoted 8 lines
Quoted 5 lines
Acked-by Hermann Pitton <[email protected]>There is simply no known broadcast in that gap on other freq. tables.
Can you please enlighten us who/what broadcasts there?
I don't know. This trick for solve problem with low sensitivity the tuners on end of band. We get it from measuments.
I believe that, since seen before on real broadcast in the VHF low/high gap.
But if there is no real broadcast at all, what it is all about for now?
You can find this "problem" in theory on almost all "new" tuners, on every TCL, TENA, YMEC and what the hell else we have melt down to be in fact only _very few_ new ones.
Get out of the lab, until it is a real problem, but keep in mind.
Cheers,
Hermann
Quoted 111 lines
Quoted 7 lines
Quoted 4 lines
With my best regards, Dmitry.
Quoted 1 line
Hi Dmitri,
Cheers,
HermannWith my best regards, Dmitry.
Quoted 101 lines
Quoted 100 lines
Quoted 100 lines
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 11 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
Andy
Quoted 5 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.
Dmitri,
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
Cheers,
Mauro.
Quoted 16 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.clinux/drivers/media/common/tuners/tuner-types.c +2
-2@@ -558,8 +558,8 @@static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *441.00 /*MHz*/ ,0x8e ,0x02 , }, + {16 *864.00 ,0x8e ,0x04 , }, };static struct tuner_params tuner_fm1216me_mk3_params[] = {
Quoted 103 lines
Signed-off-by Beholder Intl. Ltd. Dmitry Belimov <[email protected]>With my best regards, Dmitry.
Quoted 98 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 10 lines
Quoted 7 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 7 lines
Quoted 5 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3
datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
Andy
Cheers,
Mauro
Quoted 7 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 4 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
Quoted 7 lines
Quoted 2 lines
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
I think need discuss about FM1216ME_MK3 because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.
With my best regards, Dmitry.
Quoted 134 lines
Cheers,
Mauro.Quoted 16 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c
---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++
b/linux/drivers/media/common/tuners/tuner-types.cTue Apr 28
03:35:42 2009 +1000 @@ -558,8 +558,8 @@
static structtuner_rangetuner_fm1216me_mk3_pal_ranges[] = {linux/drivers/media/common/tuners/tuner-types.c +2
-2{ 16 * 158.00 /*MHz*/, 0x8e, 0x01, }, - { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 108 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov
<[email protected]>With my best regards, Dmitry.
Quoted 102 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 11 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyCheers,
Mauro
Hi,
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 15 lines
Quoted 12 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 6 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
Quoted 7 lines
Quoted 2 lines
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.
hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Some examples, user success reports, to make it more easily to understand? I think it can only change some _very little_ under already worst conditions.
Cheers,
Hermann
Quoted 136 lines
With my best regards, Dmitry.
Quoted 134 lines
Cheers,
Mauro.Quoted 16 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c
---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++
b/linux/drivers/media/common/tuners/tuner-types.cTue Apr 28
03:35:42 2009 +1000 @@ -558,8 +558,8 @@
static structtuner_rangetuner_fm1216me_mk3_pal_ranges[] = {linux/drivers/media/common/tuners/tuner-types.c +2
-2{ 16 * 158.00 /*MHz*/, 0x8e, 0x01, }, - { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 108 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov
<[email protected]>With my best regards, Dmitry.
Quoted 102 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 2 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 11 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyCheers,
Mauro
Hi,
Quoted 28 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 15 lines
Quoted 12 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 6 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
Quoted 8 lines
Quoted 2 lines
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
Quoted 7 lines
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.
This is my idea for RFC about TOP AGC:
1. Add gain variable to tuner structure.
2. Add V4L2_CID_GAIN control to saa7134 and disable this control.
3. Add workaround to simple_post_tune function for write sensitivity level to the tuner.
4. Enable V4L2_CID_GAIN control when module load if card is right.
My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
If TV card is not touch V4L2_CTRL_FLAG_DISABLED in this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.
linux/drivers/media/common/tuners/tuner-simple.c +49 -1
@@ -116,6 +116,7 @@u32 frequency;u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */
@@ -495,15 +507,57 @@ "(should be 4)\n", rc);break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */ +switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + +tuner_dbg ("tv 0x%02x 0x%02x 0x%02x 0x%02x\n" , + buffer[0 ], buffer[1 ], buffer[2 ], buffer[3 ]); + + rc =tuner_i2c_xfer_send (&priv->i2c_props, buffer,4 ); +if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }
linux/drivers/media/video/saa7134/saa7134-cards.c +12 -0
@@ -6506,6 +6806,20 @@saa_call_all (dev, tuner, s_config, &tea5767_cfg);break ; } +case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ) {/* BUG here */ +/* enable this control */ + ctl->flags &= ~(V4L2_CTRL_FLAG_DISABLED ); + } + } }/* switch() */ saa7134_tuner_setup (dev);
linux/drivers/media/video/saa7134/saa7134-video.c +17 -0
@@ -417,6 +417,15 @@ .step = 1, .default_value = 0, .type = V4L2_CTRL_TYPE_INTEGER, + }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type = V4L2_CTRL_TYPE_INTEGER, + .flags = V4L2_CTRL_FLAG_DISABLED, },{ .id = V4L2_CID_HFLIP, .name = "Mirror",
@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;
@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST : dev->ctl_contrast = c->value;
@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id (V4L2_CID_BRIGHTNESS )->default_value; dev->ctl_contrast =ctrl_by_id (V4L2_CID_CONTRAST )->default_value; dev->ctl_hue =ctrl_by_id (V4L2_CID_HUE )->default_value; + dev->ctl_gain =ctrl_by_id (V4L2_CID_GAIN )->default_value; dev->ctl_saturation =ctrl_by_id (V4L2_CID_SATURATION )->default_value; dev->ctl_volume =ctrl_by_id (V4L2_CID_AUDIO_VOLUME )->default_value; dev->ctl_mute =1 ;// ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value;
linux/drivers/media/video/saa7134/saa7134.h +1 -0
@@ -548,6 +558,7 @@int ctl_bright;int ctl_contrast;int ctl_hue; +int ctl_gain;/* gain */ int ctl_saturation;int ctl_freq;int ctl_mute;/* audio */
With my best regards, Dmitry.
Quoted 144 lines
Cheers,
HermannQuoted 139 lines
With my best regards, Dmitry.
Quoted 137 lines
Cheers,
Mauro.Quoted 17 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++ b/linux/drivers/media/common/tuners/tuner-types.c Tue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static struct
tuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 110 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
With my best regards, Dmitry.
Quoted 104 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 9 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyCheers,
Mauro
Hi Dmitry,
Am Mittwoch, den 29.04.2009, 20:12 +1000 schrieb Dmitri Belimov:
Quoted 34 lines
Hi,
Quoted 32 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 15 lines
Quoted 12 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 6 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
Quoted 8 lines
Quoted 2 lines
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Quoted 5 lines
Quoted 3 lines
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.This is my idea for RFC about TOP AGC:
what about to create a new FM1216ME MK3 tuner type for testing?
It is for sure maybe the best tuner around and likely is also the best for tweaks in countries with huge lands to cover, not restricted to Russia, Australia or Canada.
I would like to have also Hans' opinion on it, since he did some final steps to get them right.
Cheers,
Hermann
Quoted 312 lines
1. Add gain variable to tuner structure.
2. AddV4L2_CID_GAINcontrol to saa7134 and disable this control.
3. Add workaround tosimple_post_tunefunction for write sensitivity level to the tuner.
4. EnableV4L2_CID_GAINcontrol when module load if card is right.My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
If TV card is not touch
V4L2_CTRL_FLAG_DISABLEDin this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-simple.clinux/drivers/media/common/tuners/tuner-simple.c +49
-1@@ -116,6 +116,7 @@u32 frequency;u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */ @@ -495,15 +507,57 @@ "(should be 4)\n", rc);break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */ +switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + +tuner_dbg ("tv 0x%02x 0x%02x 0x%02x 0x%02x\n" , + buffer[0 ], buffer[1 ], buffer[2 ], buffer[3 ]); + + rc =tuner_i2c_xfer_send (&priv->i2c_props, buffer,4 ); +if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-cards.clinux/drivers/media/video/saa7134/saa7134-cards.c +12
-0@@ -6506,6 +6806,20 @@saa_call_all (dev, tuner, s_config, &tea5767_cfg);break ; } +case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ) {/* BUG here */ +/* enable this control */ + ctl->flags &= ~(V4L2_CTRL_FLAG_DISABLED ); + } + } }/* switch() */ saa7134_tuner_setup (dev);diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-video.clinux/drivers/media/video/saa7134/saa7134-video.c +17
-0@@ -417,6 +417,15 @@ .step = 1, .default_value = 0, .type = V4L2_CTRL_TYPE_INTEGER, + }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type = V4L2_CTRL_TYPE_INTEGER, + .flags = V4L2_CTRL_FLAG_DISABLED, },{ .id = V4L2_CID_HFLIP, .name = "Mirror",@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST : dev->ctl_contrast = c->value;@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id (V4L2_CID_BRIGHTNESS )->default_value; dev->ctl_contrast =ctrl_by_id (V4L2_CID_CONTRAST )->default_value; dev->ctl_hue =ctrl_by_id (V4L2_CID_HUE )->default_value; + dev->ctl_gain =ctrl_by_id (V4L2_CID_GAIN )->default_value; dev->ctl_saturation =ctrl_by_id (V4L2_CID_SATURATION )->default_value; dev->ctl_volume =ctrl_by_id (V4L2_CID_AUDIO_VOLUME )->default_value; dev->ctl_mute =1 ;// ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value; diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134.hlinux/drivers/media/video/saa7134/saa7134.h +1
-0@@ -548,6 +558,7 @@int ctl_bright;int ctl_contrast;int ctl_hue; +int ctl_gain;/* gain */ int ctl_saturation;int ctl_freq;int ctl_mute;/* audio */ With my best regards, Dmitry.
Quoted 144 lines
Cheers,
HermannQuoted 139 lines
With my best regards, Dmitry.
Quoted 137 lines
Cheers,
Mauro.Quoted 17 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++ b/linux/drivers/media/common/tuners/tuner-types.c Tue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static struct
tuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 110 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
With my best regards, Dmitry.
Quoted 104 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 9 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyCheers,
Mauro
Hi Hermann
Quoted 38 lines
Hi Dmitry,
Am Mittwoch, den 29.04.2009, 20:12 +1000 schrieb Dmitri Belimov:
Quoted 35 lines
Hi,
Quoted 33 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 19 lines
Quoted 7 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 4 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
Quoted 8 lines
Quoted 2 lines
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
Quoted 5 lines
You mark patch with TOP AGC not this.
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.This is my idea for RFC about TOP AGC:
what about to create a new FM1216ME MK3 tuner type for testing?
Yes. Can you do it?
I start add MK5 tuner.
Quoted 3 lines
It is for sure maybe the best tuner around and likely is also the best for tweaks in countries with huge lands to cover, not restricted to Russia, Australia or Canada.
All our tuners tested with all standarts SECAM, PAL, NTSC because big country, some people want receive TV from Korea and Japan. For tests, our hardware engineer has hardware TV generator.
With my best regards, Dmitry.
Quoted 334 lines
I would like to have also Hans' opinion on it, since he did some final steps to get them right.
Cheers,
HermannQuoted 327 lines
1. Add gain variable to tuner structure.
2. AddV4L2_CID_GAINcontrol to saa7134 and disable this control.
3. Add workaround tosimple_post_tunefunction for write sensitivity level to the tuner. 4. EnableV4L2_CID_GAINcontrol when module load if card is right.My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
If TV card is not touch
V4L2_CTRL_FLAG_DISABLEDin this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-simple.c---a/linux/drivers/media/common/tuners/tuner-simple.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/common/tuners/tuner-simple.cTue Apr
21 09:44:38 2009 +1000 @@ -116,6 +116,7 @@ u32 frequency;linux/drivers/media/common/tuners/tuner-simple.c +1
-1u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */ @@ -495,15 +507,57 @@ "(should be 4)\n", rc);
linux/drivers/media/common/tuners/tuner-simple.c +40
-0break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */ +switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + + tuner_dbg("tv 0x%02x 0x%02x 0x%02x 0x%02x\n", + buffer[0], buffer[1], buffer[2],buffer[3]); +
(quoted diff) +1
-0+ rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer,4);
linux/drivers/media/common/tuners/tuner-simple.c +6
-1+if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-cards.c---a/linux/drivers/media/video/saa7134/saa7134-cards.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-cards.cTue Apr
21 09:44:38 2009 +1000 @@ -6506,6 +6806,20 @@saa_call_all(dev, tuner, s_config, &tea5767_cfg); break; }linux/drivers/media/video/saa7134/saa7134-cards.c +8
-0+case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ){ /* BUG here */
linux/drivers/media/video/saa7134/saa7134-cards.c +4
-0+/* enable this control */ + ctl->flags &= ~(V4L2_CTRL_FLAG_DISABLED ); + } + } }/* switch() */ saa7134_tuner_setup (dev);diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-video.c---a/linux/drivers/media/video/saa7134/saa7134-video.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-video.cTue Apr
21 09:44:38 2009 +1000 @@ -417,6 +417,15 @@ .step =
1, .default_value = 0, .type =V4L2_CTRL_TYPE_INTEGER,linux/drivers/media/video/saa7134/saa7134-video.c +16
-0+ }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type = V4L2_CTRL_TYPE_INTEGER, + .flags = V4L2_CTRL_FLAG_DISABLED, },{ .id = V4L2_CID_HFLIP, .name = "Mirror",@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST : dev->ctl_contrast = c->value;@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id(V4L2_CID_BRIGHTNESS)->default_value;
dev->ctl_contrast= ctrl_by_id(V4L2_CID_CONTRAST)->default_value;dev->ctl_hue= ctrl_by_id(V4L2_CID_HUE)->default_value;(quoted diff) +1
-0+ dev->ctl_gain =ctrl_by_id(V4L2_CID_GAIN)->default_value;
dev->ctl_saturation= ctrl_by_id(V4L2_CID_SATURATION)->default_value;dev->ctl_volume= ctrl_by_id(V4L2_CID_AUDIO_VOLUME)->default_value;dev->ctl_mute= 1; //
ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value; diff -r43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134.h---a/linux/drivers/media/video/saa7134/saa7134.hTue Jan 27
23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134.hTue Apr 21
09:44:38 2009 +1000 @@ -548,6 +558,7 @@ intctl_bright; intctl_contrast;
intctl_hue;linux/drivers/media/video/saa7134/saa7134.h +1
-0+int ctl_gain;/* gain */ int ctl_saturation;int ctl_freq;int ctl_mute;/* audio */
With my best regards, Dmitry.
Quoted 150 lines
Cheers,
HermannQuoted 145 lines
With my best regards, Dmitry.
Quoted 143 lines
Cheers,
Mauro.Quoted 17 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++ b/linux/drivers/media/common/tuners/tuner-types.c Tue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static struct
tuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 116 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
With my best regards, Dmitry.
Quoted 110 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 21 lines · Dmitri Belimov
Hi Andy
Quoted 12 lines
Dmitri,
Quoted 6 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle
band the sensitivity of receiver not good. If we
switch to higher band, sensitivity more better.
Hardware trick.Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 6 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 9 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyCheers,
Mauro
Hi,
Am Mittwoch, den 06.05.2009, 04:42 +1000 schrieb Dmitri Belimov:
Quoted 29 lines
Hi Hermann
Quoted 27 lines
Hi Dmitry,
Am Mittwoch, den 29.04.2009, 20:12 +1000 schrieb Dmitri Belimov:
Quoted 24 lines
Hi,
Quoted 22 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 21 lines
Quoted 7 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 4 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
Quoted 8 lines
Quoted 2 lines
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
From the
tda9887_3datasheet.
8.2 Tuner AGC and VIF-AGC
This block adapts the voltages, generated at the VIF-AGC and SIF-AGC detectors, to the internal signal processing at the VIF and SIF amplifiers and performs the tuner AGC control current generation. The onset of the tuner AGC control current generation can be set either via the I2C-bus (see Table 13) or optionally by a potentiometer at pin TOP (in case that the I2C-bus information cannot be stored). The presence of a potentiometer is automatically detected and the I2C-bus setting is disabled.
Reads for me that on some tuners, like NTSC only, the tuner AGC is fix.
To change it per channel is not needed at all.
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 8 lines
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
This is my idea for RFC about TOP AGC:
what about to create a new FM1216ME MK3 tuner type for testing?
Yes. Can you do it?
I start add MK5 tuner.
Yes, if really needed, but I see no hint anywhere that it should be useful to have TOP settings per channel for user applications and will stay away from it.
For the change of UHF start I don't see any problem.
SECAM_DK is never mentioned explicitly in the old datasheet we have at ivtvdriver.org. Maybe we miss something here, but you try to change over the full range and simply 109 dB is recommended for negative demodulation. (page 13 for recommended TOP settings)
http://dl.ivtvdriver.org/datasheets/tuners
Maybe we are really talking about different tuner versions/revisions.
Can you have a look at the tuner pictures I did send?
Quoted 7 lines
Quoted 3 lines
It is for sure maybe the best tuner around and likely is also the best for tweaks in countries with huge lands to cover, not restricted to Russia, Australia or Canada.
All our tuners tested with all standarts SECAM, PAL, NTSC because big country, some people want receive TV from Korea and Japan. For tests, our hardware engineer has hardware TV generator.
That confuses me a lot :)
You mean you test that tuner with its PAL/SECAM SAW filters on NTSC_KR and NTSC_JP ?
Quoted 5 lines
With my best regards, Dmitry.
Quoted 3 lines
I would like to have also Hans' opinion on it, since he did some final steps to get them right.
Andy might have a look too. Please wait a little for more opinions.
Cheers,
Hermann
Quoted 329 lines
Quoted 329 lines
Quoted 328 lines
1. Add gain variable to tuner structure.
2. AddV4L2_CID_GAINcontrol to saa7134 and disable this control.
3. Add workaround tosimple_post_tunefunction for write sensitivity level to the tuner. 4. EnableV4L2_CID_GAINcontrol when module load if card is right.My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
If TV card is not touch
V4L2_CTRL_FLAG_DISABLEDin this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-simple.c---a/linux/drivers/media/common/tuners/tuner-simple.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/common/tuners/tuner-simple.cTue Apr
21 09:44:38 2009 +1000 @@ -116,6 +116,7 @@ u32 frequency;linux/drivers/media/common/tuners/tuner-simple.c +1
-1u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */ @@ -495,15 +507,57 @@ "(should be 4)\n", rc);
linux/drivers/media/common/tuners/tuner-simple.c +40
-0break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */ +switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + + tuner_dbg("tv 0x%02x 0x%02x 0x%02x 0x%02x\n", + buffer[0], buffer[1], buffer[2],buffer[3]); +
(quoted diff) +1
-0+ rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer,4);
linux/drivers/media/common/tuners/tuner-simple.c +6
-1+if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-cards.c---a/linux/drivers/media/video/saa7134/saa7134-cards.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-cards.cTue Apr
21 09:44:38 2009 +1000 @@ -6506,6 +6806,20 @@saa_call_all(dev, tuner, s_config, &tea5767_cfg); break; }linux/drivers/media/video/saa7134/saa7134-cards.c +8
-0+case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ){ /* BUG here */
linux/drivers/media/video/saa7134/saa7134-cards.c +4
-0+/* enable this control */ + ctl->flags &= ~(V4L2_CTRL_FLAG_DISABLED ); + } + } }/* switch() */ saa7134_tuner_setup (dev);diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-video.c---a/linux/drivers/media/video/saa7134/saa7134-video.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-video.cTue Apr
21 09:44:38 2009 +1000 @@ -417,6 +417,15 @@ .step =
1, .default_value = 0, .type =V4L2_CTRL_TYPE_INTEGER,linux/drivers/media/video/saa7134/saa7134-video.c +16
-0+ }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type = V4L2_CTRL_TYPE_INTEGER, + .flags = V4L2_CTRL_FLAG_DISABLED, },{ .id = V4L2_CID_HFLIP, .name = "Mirror",@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST : dev->ctl_contrast = c->value;@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id(V4L2_CID_BRIGHTNESS)->default_value;
dev->ctl_contrast= ctrl_by_id(V4L2_CID_CONTRAST)->default_value;dev->ctl_hue= ctrl_by_id(V4L2_CID_HUE)->default_value;(quoted diff) +1
-0+ dev->ctl_gain =ctrl_by_id(V4L2_CID_GAIN)->default_value;
dev->ctl_saturation= ctrl_by_id(V4L2_CID_SATURATION)->default_value;dev->ctl_volume= ctrl_by_id(V4L2_CID_AUDIO_VOLUME)->default_value;dev->ctl_mute= 1; //
ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value; diff -r43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134.h---a/linux/drivers/media/video/saa7134/saa7134.hTue Jan 27
23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134.hTue Apr 21
09:44:38 2009 +1000 @@ -548,6 +558,7 @@ intctl_bright; intctl_contrast;
intctl_hue;linux/drivers/media/video/saa7134/saa7134.h +1
-0+int ctl_gain;/* gain */ int ctl_saturation;int ctl_freq;int ctl_mute;/* audio */
With my best regards, Dmitry.
Quoted 150 lines
Cheers,
HermannQuoted 145 lines
With my best regards, Dmitry.
Quoted 143 lines
Cheers,
Mauro.Quoted 17 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++ b/linux/drivers/media/common/tuners/tuner-types.c Tue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static struct
tuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 116 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
With my best regards, Dmitry.
Quoted 110 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 21 lines · Dmitri Belimov
Hi Andy
Quoted 12 lines
Dmitri,
Quoted 6 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle
band the sensitivity of receiver not good. If we
switch to higher band, sensitivity more better.
Hardware trick.Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 6 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 9 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyCheers,
Mauro
Quoted 53 lines · hermann pitton
Hi,
Am Mittwoch, den 06.05.2009, 04:42 +1000 schrieb Dmitri Belimov:
Quoted 29 lines
Hi Hermann
Quoted 27 lines
Hi Dmitry,
Am Mittwoch, den 29.04.2009, 20:12 +1000 schrieb Dmitri Belimov:
Quoted 24 lines
Hi,
Quoted 22 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 21 lines
Quoted 7 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 4 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
Quoted 8 lines
Quoted 2 lines
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
From the
tda9887_3datasheet.8.2 Tuner AGC and VIF-AGC
This block adapts the voltages, generated at the VIF-AGC and SIF-AGC detectors, to the internal signal processing at the VIF and SIF amplifiers and performs the tuner AGC control current generation. The onset of the tuner AGC control current generation can be set either via the I2C-bus (see Table 13) or optionally by a potentiometer at pin TOP (in case that the I2C-bus information cannot be stored). The presence of a potentiometer is automatically detected and the I2C-bus setting is disabled.
Quoted 3 lines
Reads for me that on some tuners, like NTSC only, the tuner AGC is fix.
To change it per channel is not needed at all.
I've started looking at the photographs of the tuner that Hermann sent. Looking at the TDA9887 v4 datasheet, I can see how the TOP related pins are (not) wired to the 1st stage oscillator/mixer chip.
Pin 9 (TOP) is supposed to either be tied to ground through a resistor or left open. This design has the pin connected to a white SMT capacitor(?) which I will assume the TDA9887 will see as an open circuit. This means the TOP in the TDA9887 should be programmable via I2C.
Pin 14 (TAGC) looks like it is unconnected. This means the TDA9887 TAGC output is not actively taking over gain control of the 1st stage RF mixer/oscialltor chip.
So this answers a question I had posed to Dmitry: Is this tuner wired up so the TDA9887 can adjust the gain of the 1st stage? That answer is no.
That means, that in this tuner, the AGC's in the two chips are operating independently and need their TOP's set in a coordinated manner that takes into account the IF filter losses and the modulation. Since the FM1216ME data sheet makes recommendations for TOP values for both chips:
RF mixer/osc chip:
109 dBμV Recommended for negative modulation
106 dBμV Recommended for positive modulation
It is recommended to set the TOP at 109 dBμV for PAL B/G, D/K, I For system L/L’, it is recommended to set the TOP at 106 dBμV. For FM radio, it is also recommended to set the TOP to 109 dBμV
IF demod chip:
C4-C0 = 10000 [0 dB, 17 mV (RMS) according to the TDA9887 datasheet]
for all FM modes and B/G D/K I L and L' systems
it is probably best to use those. I can try and look at the IF filter from the picutres Hermann sent, but I'm not sure I'd be able to figure out the loss and come up with better TOP setting recommendations than the manufacturer's datasheet.
Quoted 13 lines
Quoted 13 lines
Quoted 12 lines
Quoted 10 lines
Quoted 8 lines
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.This is my idea for RFC about TOP AGC:
what about to create a new FM1216ME MK3 tuner type for testing?
Quoted 7 lines
Quoted 3 lines
Yes. Can you do it?
I start add MK5 tuner.
Yes, if really needed, but I see no hint anywhere that it should be useful to have TOP settings per channel for user applications and will stay away from it.
Right now, I don't think the tuner-simple.c code adjusts the TOP value based on the video system or FM mode. It probably should.
I don't think a user control will be very useful.
Quoted 1 line
For the change of UHF start I don't see any problem.
If you're talking about the frequency for the bandswitch, I don't see a problem either in general. It may cause a problem for clones of the FM1216ME MK3 that don't have the same filter performance near the cutover, but use the same tuner defintion as the FM1216ME MK3 in tuner-types.c.
It may be best to point any clones to a new entry that looks like the current FM1216ME MK3 entry unmodified.
Regards,
Andy
Quoted 369 lines
SECAM_DKis never mentioned explicitly in the old datasheet we have at ivtvdriver.org. Maybe we miss something here, but you try to change over the full range and simply 109 dB is recommended for negative demodulation. (page 13 for recommended TOP settings)
http://dl.ivtvdriver.org/datasheets/tunersMaybe we are really talking about different tuner versions/revisions.
Can you have a look at the tuner pictures I did send?
Quoted 7 lines
Quoted 3 lines
It is for sure maybe the best tuner around and likely is also the best for tweaks in countries with huge lands to cover, not restricted to Russia, Australia or Canada.
All our tuners tested with all standarts SECAM, PAL, NTSC because big country, some people want receive TV from Korea and Japan. For tests, our hardware engineer has hardware TV generator.
That confuses me a lot :)
You mean you test that tuner with its PAL/SECAM SAW filters on
NTSC_KRandNTSC_JP?Quoted 5 lines
With my best regards, Dmitry.
Quoted 3 lines
I would like to have also Hans' opinion on it, since he did some final steps to get them right.
Andy might have a look too. Please wait a little for more opinions.
Cheers,
HermannQuoted 324 lines
Quoted 324 lines
Quoted 324 lines
1. Add gain variable to tuner structure.
2. AddV4L2_CID_GAINcontrol to saa7134 and disable this control.
3. Add workaround tosimple_post_tunefunction for write sensitivity level to the tuner. 4. EnableV4L2_CID_GAINcontrol when module load if card is right.My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
If TV card is not touch
V4L2_CTRL_FLAG_DISABLEDin this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-simple.c---a/linux/drivers/media/common/tuners/tuner-simple.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/common/tuners/tuner-simple.cTue Apr
21 09:44:38 2009 +1000 @@ -116,6 +116,7 @@ u32 frequency;linux/drivers/media/common/tuners/tuner-simple.c +1
-1u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */ @@ -495,15 +507,57 @@ "(should be 4)\n", rc);
linux/drivers/media/common/tuners/tuner-simple.c +40
-0break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */ +switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + + tuner_dbg("tv 0x%02x 0x%02x 0x%02x 0x%02x\n", + buffer[0], buffer[1], buffer[2],buffer[3]); +
(quoted diff) +1
-0+ rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer,4);
linux/drivers/media/common/tuners/tuner-simple.c +6
-1+if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-cards.c---a/linux/drivers/media/video/saa7134/saa7134-cards.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-cards.cTue Apr
21 09:44:38 2009 +1000 @@ -6506,6 +6806,20 @@saa_call_all(dev, tuner, s_config, &tea5767_cfg); break; }linux/drivers/media/video/saa7134/saa7134-cards.c +8
-0+case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ){ /* BUG here */
linux/drivers/media/video/saa7134/saa7134-cards.c +4
-0+/* enable this control */ + ctl->flags &= ~(V4L2_CTRL_FLAG_DISABLED ); + } + } }/* switch() */ saa7134_tuner_setup (dev);diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-video.c---a/linux/drivers/media/video/saa7134/saa7134-video.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-video.cTue Apr
21 09:44:38 2009 +1000 @@ -417,6 +417,15 @@ .step =
1, .default_value = 0, .type =V4L2_CTRL_TYPE_INTEGER,linux/drivers/media/video/saa7134/saa7134-video.c +16
-0+ }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type = V4L2_CTRL_TYPE_INTEGER, + .flags = V4L2_CTRL_FLAG_DISABLED, },{ .id = V4L2_CID_HFLIP, .name = "Mirror",@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST : dev->ctl_contrast = c->value;@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id(V4L2_CID_BRIGHTNESS)->default_value;
dev->ctl_contrast= ctrl_by_id(V4L2_CID_CONTRAST)->default_value;dev->ctl_hue= ctrl_by_id(V4L2_CID_HUE)->default_value;(quoted diff) +1
-0+ dev->ctl_gain =ctrl_by_id(V4L2_CID_GAIN)->default_value;
dev->ctl_saturation= ctrl_by_id(V4L2_CID_SATURATION)->default_value;dev->ctl_volume= ctrl_by_id(V4L2_CID_AUDIO_VOLUME)->default_value;dev->ctl_mute= 1; //
ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value; diff -r43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134.h---a/linux/drivers/media/video/saa7134/saa7134.hTue Jan 27
23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134.hTue Apr 21
09:44:38 2009 +1000 @@ -548,6 +558,7 @@ intctl_bright; intctl_contrast;
intctl_hue;linux/drivers/media/video/saa7134/saa7134.h +1
-0+int ctl_gain;/* gain */ int ctl_saturation;int ctl_freq;int ctl_mute;/* audio */
With my best regards, Dmitry.
Quoted 146 lines
Cheers,
HermannQuoted 143 lines
With my best regards, Dmitry.
Quoted 141 lines
Cheers,
Mauro.Quoted 133 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++ b/linux/drivers/media/common/tuners/tuner-types.c Tue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static struct
tuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
With my best regards, Dmitry.
Quoted 110 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 21 lines · Dmitri Belimov
Hi Andy
Quoted 12 lines
Dmitri,
Quoted 6 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle
band the sensitivity of receiver not good. If we
switch to higher band, sensitivity more better.
Hardware trick.Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 6 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 9 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyQuoted 5 lines
Quoted 5 lines
Quoted 4 lines
Quoted 4 lines
Quoted 2 lines
Quoted 2 lines
Cheers,
Mauro--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Andy
Quoted 143 lines · hermann pitton
Quoted 54 lines
Hi,
Am Mittwoch, den 06.05.2009, 04:42 +1000 schrieb Dmitri Belimov:
Quoted 30 lines
Hi Hermann
Quoted 28 lines
Hi Dmitry,
Am Mittwoch, den 29.04.2009, 20:12 +1000 schrieb Dmitri Belimov:
Quoted 25 lines
Hi,
Quoted 23 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 21 lines
Quoted 7 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 4 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
Quoted 8 lines
Quoted 2 lines
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
From the
tda9887_3datasheet.8.2 Tuner AGC and VIF-AGC
This block adapts the voltages, generated at the VIF-AGC and SIF-AGC detectors, to the internal signal processing at the VIF and SIF amplifiers and performs the tuner AGC control current generation. The onset of the tuner AGC control current generation can be set either via the I2C-bus (see Table 13) or optionally by a potentiometer at pin TOP (in case that the I2C-bus information cannot be stored). The presence of a potentiometer is automatically detected and the I2C-bus setting is disabled.
Quoted 4 lines
Reads for me that on some tuners, like NTSC only, the tuner AGC is fix.
To change it per channel is not needed at all.
I've started looking at the photographs of the tuner that Hermann sent. Looking at the TDA9887 v4 datasheet, I can see how the TOP related pins are (not) wired to the 1st stage oscillator/mixer chip.
Pin 9 (TOP) is supposed to either be tied to ground through a resistor or left open. This design has the pin connected to a white SMT capacitor(?) which I will assume the TDA9887 will see as an open circuit. This means the TOP in the TDA9887 should be programmable via I2C.
Pin 14 (TAGC) looks like it is unconnected. This means the TDA9887 TAGC output is not actively taking over gain control of the 1st stage RF mixer/oscialltor chip.
So this answers a question I had posed to Dmitry: Is this tuner wired up so the TDA9887 can adjust the gain of the 1st stage? That answer is no.
That means, that in this tuner, the AGC's in the two chips are operating independently and need their TOP's set in a coordinated manner that takes into account the IF filter losses and the modulation. Since the FM1216ME data sheet makes recommendations for TOP values for both chips:
RF mixer/osc chip:
109 dBμV Recommended for negative modulation
106 dBμV Recommended for positive modulationIt is recommended to set the TOP at 109 dBμV for PAL B/G, D/K, I For system L/L’, it is recommended to set the TOP at 106 dBμV. For FM radio, it is also recommended to set the TOP to 109 dBμV
IF demod chip:
C4-C0 = 10000 [0 dB, 17 mV (RMS) according to the TDA9887 datasheet]
for all FM modes and B/G D/K I L and L' systemsit is probably best to use those. I can try and look at the IF filter from the picutres Hermann sent, but I'm not sure I'd be able to figure out the loss and come up with better TOP setting recommendations than the manufacturer's datasheet.
Quoted 14 lines
Quoted 14 lines
Quoted 13 lines
Quoted 11 lines
Quoted 9 lines
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.This is my idea for RFC about TOP AGC:
what about to create a new FM1216ME MK3 tuner type for testing?
Quoted 7 lines
Quoted 3 lines
Yes. Can you do it?
I start add MK5 tuner.
Yes, if really needed, but I see no hint anywhere that it should be useful to have TOP settings per channel for user applications and will stay away from it.
Right now, I don't think the
tuner-simple.ccode adjusts the TOP value based on the video system or FM mode. It probably should.I don't think a user control will be very useful.
Quoted 1 line
For the change of UHF start I don't see any problem.
If you're talking about the frequency for the bandswitch, I don't see a problem either in general. It may cause a problem for clones of the FM1216ME MK3 that don't have the same filter performance near the cutover, but use the same tuner defintion as the FM1216ME MK3 in
tuner-types.c.
Quoted 29 lines
It may be best to point any clones to a new entry that looks like the current FM1216ME MK3 entry unmodified.
Regards,
AndyQuoted 23 lines
SECAM_DKis never mentioned explicitly in the old datasheet we have at ivtvdriver.org. Maybe we miss something here, but you try to change over the full range and simply 109 dB is recommended for negative demodulation. (page 13 for recommended TOP settings)
http://dl.ivtvdriver.org/datasheets/tunersMaybe we are really talking about different tuner
versions/revisions.Can you have a look at the tuner pictures I did send?
Quoted 7 lines
Quoted 3 lines
It is for sure maybe the best tuner around and likely is also the best for tweaks in countries with huge lands to cover, not restricted to Russia, Australia or Canada.
All our tuners tested with all standarts SECAM, PAL, NTSC because big country, some people want receive TV from Korea and Japan. For tests, our hardware engineer has hardware TV generator.
That confuses me a lot :)
You mean you test that tuner with its PAL/SECAM SAW filters on
NTSC_KRandNTSC_JP?
The has 1216 3 SAW - 5.5, 6.0 and 6.5 (BG, I, DK)
The has 1236/1286 1 SAW - 4.5 (M/N)
This is one more trick.
1. Set SAW to 5.5MHz
2. Decode sound via SIF. The saa713x can decode M sound channel.
Of course need make a workaround for this.
With my best regards, Dmitry.
Quoted 364 lines
Quoted 363 lines
Quoted 4 lines
Quoted 4 lines
I would like to have also Hans' opinion on it, since he did some final steps to get them right.
Andy might have a look too. Please wait a little for more opinions.
Cheers,
HermannQuoted 342 lines
Quoted 342 lines
Quoted 342 lines
1. Add gain variable to tuner structure.
2. AddV4L2_CID_GAINcontrol to saa7134 and disable this control. 3. Add workaround tosimple_post_tunefunction for write sensitivity level to the tuner. 4. EnableV4L2_CID_GAINcontrol when module load if card is right.My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
If TV card is not touch
V4L2_CTRL_FLAG_DISABLEDin this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-simple.c---a/linux/drivers/media/common/tuners/tuner-simple.cTueJan 27 23:47:50 2009 -0200 +++ b/linux/drivers/media/common/tuners/tuner-simple.c Tue Apr 21 09:44:38 2009 +1000 @@ -116,6 +116,7 @@ u32 frequency;linux/drivers/media/common/tuners/tuner-simple.c +1
-1u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */ @@ -495,15 +507,57 @@ "(should be 4)\n", rc);
linux/drivers/media/common/tuners/tuner-simple.c +3
-0break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */
linux/drivers/media/common/tuners/tuner-simple.c +37
-0+switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + + tuner_dbg("tv 0x%02x 0x%02x 0x%02x 0x%02x\n", + buffer[0], buffer[1], buffer[2],buffer[3]); +
(quoted diff) +1
-0+ rc = tuner_i2c_xfer_send(&priv->i2c_props,buffer, 4);
linux/drivers/media/common/tuners/tuner-simple.c +6
-1+if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-cards.c---a/linux/drivers/media/video/saa7134/saa7134-cards.cTue Jan 27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-cards.cTue Apr 21 09:44:38 2009 +1000 @@ -6506,6 +6806,20 @@saa_call_all(dev, tuner, s_config, &tea5767_cfg); break; }linux/drivers/media/video/saa7134/saa7134-cards.c +8
-0+case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ){ /* BUG here */
(quoted diff) +2
-0+ /* enable this control */ + ctl->flags &=~(V4L2_CTRL_FLAG_DISABLED);
linux/drivers/media/video/saa7134/saa7134-cards.c +2
-0+ } + } }/* switch() */ saa7134_tuner_setup (dev);diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-video.c---a/linux/drivers/media/video/saa7134/saa7134-video.cTue Jan 27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-video.cTue Apr 21 09:44:38 2009 +1000 @@ -417,6 +417,15
@@ .step = 1, .default_value = 0, .type =V4L2_CTRL_TYPE_INTEGER,linux/drivers/media/video/saa7134/saa7134-video.c +8
-0+ }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type =
V4L2_CTRL_TYPE_INTEGER,(quoted diff) +1
-0+ .flags =
V4L2_CTRL_FLAG_DISABLED, },{linux/drivers/media/video/saa7134/saa7134-video.c +7
-0.id = V4L2_CID_HFLIP, .name = "Mirror",@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST :linux/drivers/media/video/saa7134/saa7134-video.c +0
-0dev->ctl_contrast = c->value;@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id (V4L2_CID_BRIGHTNESS )->default_value;
dev->ctl_contrast= ctrl_by_id(V4L2_CID_CONTRAST)->default_value;dev->ctl_hue= ctrl_by_id(V4L2_CID_HUE)->default_value;(quoted diff) +1
-0+ dev->ctl_gain =ctrl_by_id(V4L2_CID_GAIN)->default_value;
dev->ctl_saturation= ctrl_by_id(V4L2_CID_SATURATION)->default_value;dev->ctl_volume= ctrl_by_id(V4L2_CID_AUDIO_VOLUME)->default_value;dev->ctl_mute= 1; //
ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value; diff -r43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134.h---a/linux/drivers/media/video/saa7134/saa7134.hTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134.hTue Apr
21 09:44:38 2009 +1000 @@ -548,6 +558,7 @@ intctl_bright;
intctl_contrast;
intctl_hue;(quoted diff) +1
-0+ int ctl_gain; /*gain */ int
ctl_saturation;(quoted diff) +0
-0int ctl_freq; int ctl_mute; /*audio */
With my best regards, Dmitry.
Quoted 157 lines
Cheers,
HermannQuoted 154 lines
With my best regards, Dmitry.
Quoted 152 lines
Cheers,
Mauro.Quoted 144 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFri Apr 24 01:46:41 2009 -0300 +++b/linux/drivers/media/common/tuners/tuner-types.cTue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static structtuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_paramstuner_fm1216me_mk3_params[] = {
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov
<[email protected]>With my best regards, Dmitry.
Quoted 119 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 21 lines · Dmitri Belimov
Hi Andy
Quoted 12 lines
Dmitri,
Quoted 6 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the
middle band the sensitivity of receiver not
good. If we switch to higher band,
sensitivity more better. Hardware trick.Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 6 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 10 lines
Quoted 9 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 10 lines
Quoted 7 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3
datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyQuoted 5 lines
Quoted 5 lines
Quoted 4 lines
Quoted 4 lines
Quoted 2 lines
Quoted 2 lines
Cheers,
Mauro--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Am Mittwoch, den 06.05.2009, 23:03 -0400 schrieb Andy Walls:
Quoted 132 lines · hermann pitton
Quoted 53 lines
Hi,
Am Mittwoch, den 06.05.2009, 04:42 +1000 schrieb Dmitri Belimov:
Quoted 29 lines
Hi Hermann
Quoted 27 lines
Hi Dmitry,
Am Mittwoch, den 29.04.2009, 20:12 +1000 schrieb Dmitri Belimov:
Quoted 24 lines
Hi,
Quoted 22 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 21 lines
Quoted 7 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 4 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
Quoted 8 lines
Quoted 2 lines
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 3 lines
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
From the
tda9887_3datasheet.8.2 Tuner AGC and VIF-AGC
This block adapts the voltages, generated at the VIF-AGC and SIF-AGC detectors, to the internal signal processing at the VIF and SIF amplifiers and performs the tuner AGC control current generation. The onset of the tuner AGC control current generation can be set either via the I2C-bus (see Table 13) or optionally by a potentiometer at pin TOP (in case that the I2C-bus information cannot be stored). The presence of a potentiometer is automatically detected and the I2C-bus setting is disabled.
Quoted 3 lines
Reads for me that on some tuners, like NTSC only, the tuner AGC is fix.
To change it per channel is not needed at all.
I've started looking at the photographs of the tuner that Hermann sent. Looking at the TDA9887 v4 datasheet, I can see how the TOP related pins are (not) wired to the 1st stage oscillator/mixer chip.
Pin 9 (TOP) is supposed to either be tied to ground through a resistor or left open. This design has the pin connected to a white SMT capacitor(?) which I will assume the TDA9887 will see as an open circuit. This means the TOP in the TDA9887 should be programmable via I2C.
Pin 14 (TAGC) looks like it is unconnected. This means the TDA9887 TAGC output is not actively taking over gain control of the 1st stage RF mixer/oscialltor chip.
So this answers a question I had posed to Dmitry: Is this tuner wired up so the TDA9887 can adjust the gain of the 1st stage? That answer is no.
That means, that in this tuner, the AGC's in the two chips are operating independently and need their TOP's set in a coordinated manner that takes into account the IF filter losses and the modulation. Since the FM1216ME data sheet makes recommendations for TOP values for both chips:
RF mixer/osc chip:
109 dBμV Recommended for negative modulation
106 dBμV Recommended for positive modulationIt is recommended to set the TOP at 109 dBμV for PAL B/G, D/K, I For system L/L’, it is recommended to set the TOP at 106 dBμV. For FM radio, it is also recommended to set the TOP to 109 dBμV
IF demod chip:
C4-C0 = 10000 [0 dB, 17 mV (RMS) according to the TDA9887 datasheet]
for all FM modes and B/G D/K I L and L' systemsit is probably best to use those. I can try and look at the IF filter from the picutres Hermann sent, but I'm not sure I'd be able to figure out the loss and come up with better TOP setting recommendations than the manufacturer's datasheet.
Quoted 13 lines
Quoted 13 lines
Quoted 12 lines
Quoted 10 lines
Quoted 8 lines
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.This is my idea for RFC about TOP AGC:
what about to create a new FM1216ME MK3 tuner type for testing?
Quoted 7 lines
Quoted 3 lines
Yes. Can you do it?
I start add MK5 tuner.
Yes, if really needed, but I see no hint anywhere that it should be useful to have TOP settings per channel for user applications and will stay away from it.
Right now, I don't think the
tuner-simple.ccode adjusts the TOP value based on the video system or FM mode. It probably should.I don't think a user control will be very useful.
Quoted 1 line
For the change of UHF start I don't see any problem.
Quoted 8 lines
If you're talking about the frequency for the bandswitch, I don't see a problem either in general. It may cause a problem for clones of the FM1216ME MK3 that don't have the same filter performance near the cutover, but use the same tuner defintion as the FM1216ME MK3 in
tuner-types.c.It may be best to point any clones to a new entry that looks like the current FM1216ME MK3 entry unmodified.
Andy, thanks a lot for participating in such stuff and I think your diagnosis is right.
Just a small question in between, already late here and not trying to cover the whole scope.
What ever should be the effect of Dmitri's trick one, changing beginning of UHF a little. We did that for midband and there was real broadcast and it improved one single channel there indeed.
But here, it is plain theory. I honor the lab results they have, no problem anyway, but to change something for not at all existing broadcast does exactly nothing, except for awaiting it in the future.
No problem with that change, but do I miss something?
Also, after hundreds of "new" tuners did appear, in the beginning not even known from where, I suggested to not allow a new tuner entry for all of them, only duplicate code, until they really need it and show off their difference.
I would like to keep it especially for this one the same. ;)
Such subsumed under it have done nothing for Linux so far and have to face their faith :) And show off, if _not_ compatible.
And not the other way round.
Dmitri, if we are talking about the same tuner and filters, we should try to get Secam D/K improvements into the original tuner entry.
That NTSC hack stuff might go elsewhere I guess.
Cheers,
Hermann
Quoted 373 lines
Regards,
AndyQuoted 369 lines
SECAM_DKis never mentioned explicitly in the old datasheet we have at ivtvdriver.org. Maybe we miss something here, but you try to change over the full range and simply 109 dB is recommended for negative demodulation. (page 13 for recommended TOP settings)
http://dl.ivtvdriver.org/datasheets/tunersMaybe we are really talking about different tuner versions/revisions.
Can you have a look at the tuner pictures I did send?
Quoted 7 lines
Quoted 3 lines
It is for sure maybe the best tuner around and likely is also the best for tweaks in countries with huge lands to cover, not restricted to Russia, Australia or Canada.
All our tuners tested with all standarts SECAM, PAL, NTSC because big country, some people want receive TV from Korea and Japan. For tests, our hardware engineer has hardware TV generator.
That confuses me a lot :)
You mean you test that tuner with its PAL/SECAM SAW filters on
NTSC_KRandNTSC_JP?Quoted 5 lines
With my best regards, Dmitry.
Quoted 3 lines
I would like to have also Hans' opinion on it, since he did some final steps to get them right.
Andy might have a look too. Please wait a little for more opinions.
Cheers,
HermannQuoted 324 lines
Quoted 324 lines
Quoted 324 lines
1. Add gain variable to tuner structure.
2. AddV4L2_CID_GAINcontrol to saa7134 and disable this control.
3. Add workaround tosimple_post_tunefunction for write sensitivity level to the tuner. 4. EnableV4L2_CID_GAINcontrol when module load if card is right.My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
If TV card is not touch
V4L2_CTRL_FLAG_DISABLEDin this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-simple.c---a/linux/drivers/media/common/tuners/tuner-simple.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/common/tuners/tuner-simple.cTue Apr
21 09:44:38 2009 +1000 @@ -116,6 +116,7 @@ u32 frequency;linux/drivers/media/common/tuners/tuner-simple.c +1
-1u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */ @@ -495,15 +507,57 @@ "(should be 4)\n", rc);
linux/drivers/media/common/tuners/tuner-simple.c +40
-0break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */ +switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + + tuner_dbg("tv 0x%02x 0x%02x 0x%02x 0x%02x\n", + buffer[0], buffer[1], buffer[2],buffer[3]); +
(quoted diff) +1
-0+ rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer,4);
linux/drivers/media/common/tuners/tuner-simple.c +6
-1+if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-cards.c---a/linux/drivers/media/video/saa7134/saa7134-cards.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-cards.cTue Apr
21 09:44:38 2009 +1000 @@ -6506,6 +6806,20 @@saa_call_all(dev, tuner, s_config, &tea5767_cfg); break; }linux/drivers/media/video/saa7134/saa7134-cards.c +8
-0+case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ){ /* BUG here */
linux/drivers/media/video/saa7134/saa7134-cards.c +4
-0+/* enable this control */ + ctl->flags &= ~(V4L2_CTRL_FLAG_DISABLED ); + } + } }/* switch() */ saa7134_tuner_setup (dev);diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-video.c---a/linux/drivers/media/video/saa7134/saa7134-video.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-video.cTue Apr
21 09:44:38 2009 +1000 @@ -417,6 +417,15 @@ .step =
1, .default_value = 0, .type =V4L2_CTRL_TYPE_INTEGER,linux/drivers/media/video/saa7134/saa7134-video.c +16
-0+ }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type = V4L2_CTRL_TYPE_INTEGER, + .flags = V4L2_CTRL_FLAG_DISABLED, },{ .id = V4L2_CID_HFLIP, .name = "Mirror",@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST : dev->ctl_contrast = c->value;@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id(V4L2_CID_BRIGHTNESS)->default_value;
dev->ctl_contrast= ctrl_by_id(V4L2_CID_CONTRAST)->default_value;dev->ctl_hue= ctrl_by_id(V4L2_CID_HUE)->default_value;(quoted diff) +1
-0+ dev->ctl_gain =ctrl_by_id(V4L2_CID_GAIN)->default_value;
dev->ctl_saturation= ctrl_by_id(V4L2_CID_SATURATION)->default_value;dev->ctl_volume= ctrl_by_id(V4L2_CID_AUDIO_VOLUME)->default_value;dev->ctl_mute= 1; //
ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value; diff -r43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134.h---a/linux/drivers/media/video/saa7134/saa7134.hTue Jan 27
23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134.hTue Apr 21
09:44:38 2009 +1000 @@ -548,6 +558,7 @@ intctl_bright; intctl_contrast;
intctl_hue;linux/drivers/media/video/saa7134/saa7134.h +1
-0+int ctl_gain;/* gain */ int ctl_saturation;int ctl_freq;int ctl_mute;/* audio */
With my best regards, Dmitry.
Quoted 146 lines
Cheers,
HermannQuoted 143 lines
With my best regards, Dmitry.
Quoted 141 lines
Cheers,
Mauro.Quoted 133 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++ b/linux/drivers/media/common/tuners/tuner-types.c Tue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static struct
tuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
With my best regards, Dmitry.
Quoted 110 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 21 lines · Dmitri Belimov
Hi Andy
Quoted 12 lines
Dmitri,
Quoted 6 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle
band the sensitivity of receiver not good. If we
switch to higher band, sensitivity more better.
Hardware trick.Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 6 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 9 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyQuoted 5 lines
Quoted 5 lines
Quoted 4 lines
Quoted 4 lines
Quoted 2 lines
Quoted 2 lines
Cheers,
Mauro--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 23 lines · hermann pitton
Am Mittwoch, den 06.05.2009, 23:03 -0400 schrieb Andy Walls:
Quoted 10 lines
Quoted 1 line
For the change of UHF start I don't see any problem.
If you're talking about the frequency for the bandswitch, I don't see a problem either in general. It may cause a problem for clones of the FM1216ME MK3 that don't have the same filter performance near the cutover, but use the same tuner defintion as the FM1216ME MK3 in
tuner-types.c.It may be best to point any clones to a new entry that looks like the current FM1216ME MK3 entry unmodified.
Andy, thanks a lot for participating in such stuff and I think your diagnosis is right.
Just a small question in between, already late here and not trying to cover the whole scope.
What ever should be the effect of Dmitri's trick one, changing beginning of UHF a little. We did that for midband and there was real broadcast and it improved one single channel there indeed.
Quoted 5 lines
But here, it is plain theory. I honor the lab results they have, no problem anyway, but to change something for not at all existing broadcast does exactly nothing, except for awaiting it in the future.
No problem with that change, but do I miss something?
Now that you ask, maybe.
It first depends on whether there is a station at 441 MHz that normally would have used the VHF-High filter and VCO, but now uses the UHF filter and VCO.
Channel designations I dug out of ivtv-tune:
S38 439.250 MHz (European cable)
H18 439.250 MHz (SECAM France)
47 440.250 MHz (PAL China)
059 440.250 MHz (PAL Argentina)
come close, but are unaffected by the change from 442 to 441 as the bandswitch cutover point. These channels fall right on top of the cutover, but are not affected by the proposed change in any meaningful way. The VHF-High filter and VCO would still be used. Dmitri's proposed change is a "don't care" unless the cutover point is changed to 440 MHz.
Let's pretend that the proposed cutover point is 440 MHz. The high frequencies in the channel (~ 447 MHz) may have perhaps been in the roll-off of the VHF-High preselector filter. At the edges of filters, amplitude ripple and especially group delay variation - two aspects of filters that cause distortion - would have been at their worst, affecting the high frequencies of the channel (sound and color sub-carriers). (I assume PAL is VSB with the carrier towards the low end, similar to NTSC.) Now instead, the low frequencies of the channel (~ 440 MHz) may be in the roll-off of the UHF preselector filter. Thus the vestigal sideband and carrier could be affected most by ripple and group delay variation of the UHF filter.
Either way, a channel at 440 MHz could face distortion by this tuner. It really depends on the preselector filter design.
I also checked the MID and HIGH band oscillator spec's in the TUA6030 datasheet. Both of them can cover 440 MHz, but it looks like the MID band VCO may be preferred since it doesn't drift as badly as the HIGH band VCO. Since I don't know the component values used in the loop filters for the VCO's, I can't do any real analysis to see which VCO would be better at handling 440 MHz. I suspect the difference may not be significant anyway.
Quoted 6 lines
Also, after hundreds of "new" tuners did appear, in the beginning not even known from where, I suggested to not allow a new tuner entry for all of them, only duplicate code, until they really need it and show off their difference.
I would like to keep it especially for this one the same. ;)
OK.
Quoted 4 lines
Such subsumed under it have done nothing for Linux so far and have to face their faith :) And show off, if _not_ compatible.
And not the other way round.
Wait until people complain? :)
Regards,
Andy
Quoted 7 lines
Dmitri, if we are talking about the same tuner and filters, we should try to get Secam D/K improvements into the original tuner entry.
That NTSC hack stuff might go elsewhere I guess.
Cheers,
Hermann
Am Freitag, den 08.05.2009, 22:01 -0400 schrieb Andy Walls:
Quoted 83 lines · hermann pitton
Quoted 23 lines
Am Mittwoch, den 06.05.2009, 23:03 -0400 schrieb Andy Walls:
Quoted 10 lines
Quoted 1 line
For the change of UHF start I don't see any problem.
If you're talking about the frequency for the bandswitch, I don't see a problem either in general. It may cause a problem for clones of the FM1216ME MK3 that don't have the same filter performance near the cutover, but use the same tuner defintion as the FM1216ME MK3 in
tuner-types.c.It may be best to point any clones to a new entry that looks like the current FM1216ME MK3 entry unmodified.
Andy, thanks a lot for participating in such stuff and I think your diagnosis is right.
Just a small question in between, already late here and not trying to cover the whole scope.
What ever should be the effect of Dmitri's trick one, changing beginning of UHF a little. We did that for midband and there was real broadcast and it improved one single channel there indeed.
Quoted 5 lines
But here, it is plain theory. I honor the lab results they have, no problem anyway, but to change something for not at all existing broadcast does exactly nothing, except for awaiting it in the future.
No problem with that change, but do I miss something?
Now that you ask, maybe.
It first depends on whether there is a station at 441 MHz that normally would have used the VHF-High filter and VCO, but now uses the UHF filter and VCO.
Channel designations I dug out of ivtv-tune:
S38 439.250 MHz (European cable)
H18 439.250 MHz (SECAM France)
47 440.250 MHz (PAL China)
059 440.250 MHz (PAL Argentina)come close, but are unaffected by the change from 442 to 441 as the bandswitch cutover point. These channels fall right on top of the cutover, but are not affected by the proposed change in any meaningful way. The VHF-High filter and VCO would still be used. Dmitri's proposed change is a "don't care" unless the cutover point is changed to 440 MHz.
Let's pretend that the proposed cutover point is 440 MHz. The high frequencies in the channel (~ 447 MHz) may have perhaps been in the roll-off of the VHF-High preselector filter. At the edges of filters, amplitude ripple and especially group delay variation - two aspects of filters that cause distortion - would have been at their worst, affecting the high frequencies of the channel (sound and color sub-carriers). (I assume PAL is VSB with the carrier towards the low end, similar to NTSC.) Now instead, the low frequencies of the channel (~ 440 MHz) may be in the roll-off of the UHF preselector filter. Thus the vestigal sideband and carrier could be affected most by ripple and group delay variation of the UHF filter.
Either way, a channel at 440 MHz could face distortion by this tuner. It really depends on the preselector filter design.
I also checked the MID and HIGH band oscillator spec's in the TUA6030 datasheet. Both of them can cover 440 MHz, but it looks like the MID band VCO may be preferred since it doesn't drift as badly as the HIGH band VCO. Since I don't know the component values used in the loop filters for the VCO's, I can't do any real analysis to see which VCO would be better at handling 440 MHz. I suspect the difference may not be significant anyway.
Quoted 6 lines
Also, after hundreds of "new" tuners did appear, in the beginning not even known from where, I suggested to not allow a new tuner entry for all of them, only duplicate code, until they really need it and show off their difference.
I would like to keep it especially for this one the same. ;)
Quoted 8 lines
OK.
Quoted 4 lines
Such subsumed under it have done nothing for Linux so far and have to face their faith :) And show off, if _not_ compatible.
And not the other way round.
Wait until people complain? :)
Yes, of course. They had it for free and that is the trap.
Again, don't try to start it the other way round.
I still wait for Dmitri, to show really off what he has.
And, unfortunately, I don't have anything to test on currently :)
Cheers,
Hermann
Quoted 13 lines
Regards,
AndyQuoted 7 lines
Dmitri, if we are talking about the same tuner and filters, we should try to get Secam D/K improvements into the original tuner entry.
That NTSC hack stuff might go elsewhere I guess.
Cheers,
Hermann
[snip]
Quoted 16 lines
Quoted 16 lines
Channel designations I dug out of ivtv-tune:
S38 439.250 MHz (European cable)
H18 439.250 MHz (SECAM France)
47 440.250 MHz (PAL China)
059 440.250 MHz (PAL Argentina)come close, but are unaffected by the change from 442 to 441 as the bandswitch cutover point. These channels fall right on top of the cutover, but are not affected by the proposed change in any meaningful way. The VHF-High filter and VCO would still be used. Dmitri's proposed change is a "don't care" unless the cutover point is changed to 440 MHz.
Quoted 1 line
Quoted 1 line
Let's pretend that the proposed cutover point is 440 MHz.
NO! it is not
Dmitri,
can you cut one off and tell us what it is all about ?
Unless you do so, all other is pointless and I likely stop to participate in such stuff.
Cheers,
Hermann
Hi All.
Quoted 19 lines
[snip]
Quoted 16 lines
Quoted 16 lines
Channel designations I dug out of ivtv-tune:
S38 439.250 MHz (European cable)
H18 439.250 MHz (SECAM France)
47 440.250 MHz (PAL China)
059 440.250 MHz (PAL Argentina)come close, but are unaffected by the change from 442 to 441 as the bandswitch cutover point. These channels fall right on top of the cutover, but are not affected by the proposed change in any meaningful way. The VHF-High filter and VCO would still be used. Dmitri's proposed change is a "don't care" unless the cutover point is changed to 440 MHz.
Quoted 1 line
Quoted 1 line
Let's pretend that the proposed cutover point is 440 MHz.
Quoted 8 lines
NO! it is not
Dmitri,
can you cut one off and tell us what it is all about ?
Unless you do so, all other is pointless and I likely stop to participate in such stuff.
Sorry my delay. I lost subject of discussion. What main question??
1. AGC TOP of RF part - I think need support for MK3
2. Changing to 441MHz is not critical. We can write some information about this case to Wiki or docs.
With my best regards, Dmitry.
Quoted 8 lines
Cheers,
Hermann
Dmitri,
Am Sonntag, den 10.05.2009, 08:52 +1000 schrieb Dmitri Belimov:
Quoted 27 lines
Hi All.
Quoted 25 lines
[snip]
Quoted 16 lines
Quoted 16 lines
Channel designations I dug out of ivtv-tune:
S38 439.250 MHz (European cable)
H18 439.250 MHz (SECAM France)
47 440.250 MHz (PAL China)
059 440.250 MHz (PAL Argentina)come close, but are unaffected by the change from 442 to 441 as the bandswitch cutover point. These channels fall right on top of the cutover, but are not affected by the proposed change in any meaningful way. The VHF-High filter and VCO would still be used. Dmitri's proposed change is a "don't care" unless the cutover point is changed to 440 MHz.
Quoted 1 line
Quoted 1 line
Let's pretend that the proposed cutover point is 440 MHz.
NO! it is not
Dmitri,
can you cut one off and tell us what it is all about ?
Quoted 7 lines
Quoted 2 lines
Unless you do so, all other is pointless and I likely stop to participate in such stuff.
Sorry my delay. I lost subject of discussion. What main question??
1. AGC TOP of RF part - I think need support for MK3
2. Changing to 441MHz is not critical. We can write some information about this case to Wiki or docs.
for 2.: Discussed to the end if you stay at 441MHz. If you still want to have it in, just send a patch and no more info is needed. (Likely Andy is giving only examples for more difficult cases, sorry.)
for 1.: I would like to be absolutely sure, that we are talking about the same tuner. I want to have the exact filters on it at least.
3.: That is what Andy noted. Following the Philips datasheet for TOP, it should be added for negative modulation, positive modulation and FM accordingly. (2 and 3 are out of discussion)
If you still have some sort of Secam fire and can improve it, we must know the tuner you are on "exactly". If it is the original Philips, without any such TOP suggestions over the full range in recent datasheets (???), I assume you might have them, I would say you can proceed, if you have shown that you are really still on the same tuner.
Cheers,
Hermann
Quoted 10 lines
Quoted 3 lines
1. AGC TOP of RF part - I think need support for MK3
2. Changing to 441MHz is not critical. We can write some information about this case to Wiki or docs.for 2.: Discussed to the end if you stay at 441MHz. If you still want to have it in, just send a patch and no more info is needed. (Likely Andy is giving only examples for more difficult cases, sorry.)
for 1.: I would like to be absolutely sure, that we are talking about the same tuner. I want to have the exact filters on it at least.
I would also say that, if we need to implement AGC TOP control, it would be better to add it at struct v4l2_tuner (VIDIOC_G_TUNER and VIDIOC_S_TUNER), instead of adding it as a control.
Quoted 23 lines
3.: That is what Andy noted. Following the Philips datasheet for TOP, it should be added for negative modulation, positive modulation and FM accordingly. (2 and 3 are out of discussion)
If you still have some sort of Secam fire and can improve it, we must know the tuner you are on "exactly". If it is the original Philips, without any such TOP suggestions over the full range in recent datasheets (???), I assume you might have them, I would say you can proceed, if you have shown that you are really still on the same tuner.
Cheers,
Hermann--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi
Quoted 9 lines
Quoted 9 lines
Quoted 3 lines
1. AGC TOP of RF part - I think need support for MK3
2. Changing to 441MHz is not critical. We can write some information about this case to Wiki or docs.for 2.: Discussed to the end if you stay at 441MHz. If you still want to have it in, just send a patch and no more info is needed. (Likely Andy is giving only examples for more difficult cases, sorry.)
Quoted 8 lines
Quoted 3 lines
for 1.: I would like to be absolutely sure, that we are talking about the same tuner. I want to have the exact filters on it at least.
I would also say that, if we need to implement AGC TOP control, it would be better to add it at struct
v4l2_tuner(VIDIOC_G_TUNERandVIDIOC_S_TUNER), instead
of adding it as a control.
Good idea.
For MK3 need control AGC TOP and TOP of TDA9887
For MK5 need control only TOP of TDA9887
With my best regards, Dmitry.
Quoted 25 lines
Quoted 24 lines
3.: That is what Andy noted. Following the Philips datasheet for TOP, it should be added for negative modulation, positive modulation and FM accordingly. (2 and 3 are out of discussion)
If you still have some sort of Secam fire and can improve it, we must know the tuner you are on "exactly". If it is the original Philips, without any such TOP suggestions over the full range in recent datasheets (???), I assume you might have them, I would say you can proceed, if you have shown that you are really still on the same tuner.
Cheers,
Hermann--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 35 lines · On Mon, 11 May 2009 05:35:51 +0200 hermann pitton <[email protected]>…
Dmitri,
Am Sonntag, den 10.05.2009, 08:52 +1000 schrieb Dmitri Belimov:
Quoted 32 lines
Hi All.
Quoted 19 lines
[snip]
Quoted 16 lines
Quoted 16 lines
Channel designations I dug out of ivtv-tune:
S38 439.250 MHz (European cable)
H18 439.250 MHz (SECAM France)
47 440.250 MHz (PAL China)
059 440.250 MHz (PAL Argentina)come close, but are unaffected by the change from 442 to 441 as the bandswitch cutover point. These channels fall right on top of the cutover, but are not affected by the proposed change in any meaningful way. The VHF-High filter and VCO would still be used. Dmitri's proposed change is a "don't care" unless the cutover point is changed to 440 MHz.
Quoted 1 line
Quoted 1 line
Let's pretend that the proposed cutover point is 440 MHz.
Quoted 8 lines
NO! it is not
Dmitri,
can you cut one off and tell us what it is all about ?
Unless you do so, all other is pointless and I likely stop to participate in such stuff.
Sorry my delay. I lost subject of discussion. What main question??
Quoted 7 lines
Quoted 3 lines
1. AGC TOP of RF part - I think need support for MK3
2. Changing to 441MHz is not critical. We can write some information about this case to Wiki or docs.for 2.: Discussed to the end if you stay at 441MHz. If you still want to have it in, just send a patch and no more info is needed. (Likely Andy is giving only examples for more difficult cases, sorry.)
This is my patch.
linux/drivers/media/common/tuners/tuner-types.c +2 -2
@@ -558,8 +558,8 @@static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *441.00 /*MHz*/ ,0x8e ,0x02 , }, + {16 *864.00 ,0x8e ,0x04 , }, };static struct tuner_params tuner_fm1216me_mk3_params[] = {
Quoted 7 lines
for 1.: I would like to be absolutely sure, that we are talking about the same tuner. I want to have the exact filters on it at least.
3.: That is what Andy noted. Following the Philips datasheet for TOP, it should be added for negative modulation, positive modulation and FM accordingly. (2 and 3 are out of discussion)
Quoted 6 lines
If you still have some sort of Secam fire and can improve it, we must know the tuner you are on "exactly". If it is the original Philips, without any such TOP suggestions over the full range in recent datasheets (???), I assume you might have them, I would say you can proceed, if you have shown that you are really still on the same tuner.
Ok. I read the datasheet, make photos inside tuner.
With my best regards, Dmitry.
Quoted 8 lines
Cheers,
Hermann
linux/drivers/media/common/tuners/tuner-types.c +2 -2
@@ -558,8 +558,8 @@static struct tuner_range tuner_fm1216me_mk3_pal_ranges[] = { {16 *158.00 /*MHz*/ ,0x8e ,0x01 , }, - {16 *442.00 /*MHz*/ ,0x8e ,0x02 , }, - {16 *999.99 ,0x8e ,0x04 , }, + {16 *441.00 /*MHz*/ ,0x8e ,0x02 , }, + {16 *864.00 ,0x8e ,0x04 , }, };static struct tuner_params tuner_fm1216me_mk3_params[] = {
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi Dmitry,
Am Mittwoch, den 13.05.2009, 07:37 +1000 schrieb Dmitri Belimov:
Quoted 57 lines
Hi hermann
Quoted 48 lines
Am Sonntag, den 10.05.2009, 08:52 +1000 schrieb Dmitri Belimov:
Quoted 27 lines
Hi All.
Quoted 25 lines
[snip]
Quoted 16 lines
Quoted 16 lines
Channel designations I dug out of ivtv-tune:
S38 439.250 MHz (European cable)
H18 439.250 MHz (SECAM France)
47 440.250 MHz (PAL China)
059 440.250 MHz (PAL Argentina)come close, but are unaffected by the change from 442 to 441 as the bandswitch cutover point. These channels fall right on top of the cutover, but are not affected by the proposed change in any meaningful way. The VHF-High filter and VCO would still be used. Dmitri's proposed change is a "don't care" unless the cutover point is changed to 440 MHz.
Quoted 1 line
Quoted 1 line
Let's pretend that the proposed cutover point is 440 MHz.
NO! it is not
Dmitri,
can you cut one off and tell us what it is all about ?
Quoted 8 lines
Quoted 2 lines
Unless you do so, all other is pointless and I likely stop to participate in such stuff.
Sorry my delay. I lost subject of discussion. What main question??
1. AGC TOP of RF part - I think need support for MK3
2. Changing to 441MHz is not critical. We can write some information about this case to Wiki or docs.for 2.: Discussed to the end if you stay at 441MHz. If you still want to have it in, just send a patch and no more info is needed. (Likely Andy is giving only examples for more difficult cases, sorry.)
for 1.: I would like to be absolutely sure, that we are talking about the same tuner. I want to have the exact filters on it at least.
3.: That is what Andy noted. Following the Philips datasheet for TOP, it should be added for negative modulation, positive modulation and FM accordingly. (2 and 3 are out of discussion)
Quoted 6 lines
If you still have some sort of Secam fire and can improve it, we must know the tuner you are on "exactly". If it is the original Philips, without any such TOP suggestions over the full range in recent datasheets (???), I assume you might have them, I would say you can proceed, if you have shown that you are really still on the same tuner.
Quoted 4 lines
This is real Philips MK3 and MK5 tuner. We have all docs from vendor.
This is some photos of the MK3 hybrid tuner. I make photos of the analog MK3 little later.
thanks a lot.
I had only a first look on this one.
There are a lot of different revisions, yours is F4 on the tuner PCB.
Taifun PLL versions vary, different combinations of ceramic and SMD filters are used for the radio IF,
but even on a revision C1 with Taifun 6034T A1 and tuner revision SV21 0437 (CTX918_V2 md7134) all three SAW filters are the same already.
A CTX925 with your Taifun 6034T B1 had also no better performance for what I can say. PCB still has C1, but SV21 0502 tuner revision.
Important to know was, that you are on original Philips tuners and SAW filters are the same. Guess this will hold for the analog FM1216ME/I MK3 too.
Good decision, it are still the best tuners for analog and digital I have around, but can't talk for Secam D/K. I wonder about missing complaints during the last four years.
Cheers,
Hermann
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi Dmitry :)
Am Donnerstag, den 14.05.2009, 10:17 +1000 schrieb Dmitri Belimov:
Quoted 92 lines
Hi
Quoted 83 lines
Hi Dmitry,
Am Mittwoch, den 13.05.2009, 07:37 +1000 schrieb Dmitri Belimov:
Quoted 61 lines
Hi hermann
Quoted 52 lines
Am Sonntag, den 10.05.2009, 08:52 +1000 schrieb Dmitri Belimov:
Quoted 31 lines
Hi All.
Quoted 20 lines
[snip]
Quoted 17 lines
Quoted 17 lines
Channel designations I dug out of ivtv-tune:
S38 439.250 MHz (European cable)
H18 439.250 MHz (SECAM France)
47 440.250 MHz (PAL China)
059 440.250 MHz (PAL Argentina)come close, but are unaffected by the change from 442 to 441 as the bandswitch cutover point. These channels fall right on top of the cutover, but are not affected by the proposed change in any meaningful way. The VHF-High filter and VCO would still be used. Dmitri's proposed change is a "don't care" unless the cutover point is changed to 440 MHz.
Quoted 1 line
Quoted 1 line
Let's pretend that the proposed cutover point is 440 MHz.
Quoted 8 lines
NO! it is not
Dmitri,
can you cut one off and tell us what it is all about ?
Unless you do so, all other is pointless and I likely stop to participate in such stuff.
Quoted 6 lines
Sorry my delay. I lost subject of discussion. What main question??
1. AGC TOP of RF part - I think need support for MK3
2. Changing to 441MHz is not critical. We can write some information about this case to Wiki or docs.for 2.: Discussed to the end if you stay at 441MHz. If you still want to have it in, just send a patch and no more info is needed. (Likely Andy is giving only examples for more difficult cases, sorry.)
for 1.: I would like to be absolutely sure, that we are talking about the same tuner. I want to have the exact filters on it at least.
3.: That is what Andy noted. Following the Philips datasheet for TOP, it should be added for negative modulation, positive modulation and FM accordingly. (2 and 3 are out of discussion)
Quoted 6 lines
If you still have some sort of Secam fire and can improve it, we must know the tuner you are on "exactly". If it is the original Philips, without any such TOP suggestions over the full range in recent datasheets (???), I assume you might have them, I would say you can proceed, if you have shown that you are really still on the same tuner.
Quoted 6 lines
This is real Philips MK3 and MK5 tuner. We have all docs from vendor.
This is some photos of the MK3 hybrid tuner. I make photos of the analog MK3 little later.
thanks a lot.
I had only a first look on this one.
There are a lot of different revisions, yours is F4 on the tuner PCB.
Taifun PLL versions vary, different combinations of ceramic and SMD filters are used for the radio IF,
but even on a revision C1 with Taifun 6034T A1 and tuner revision SV21 0437 (
CTX918_V2md7134) all three SAW filters are the same already.Quoted 6 lines
A CTX925 with your Taifun 6034T B1 had also no better performance for what I can say. PCB still has C1, but SV21 0502 tuner revision.
Important to know was, that you are on original Philips tuners and SAW filters are the same. Guess this will hold for the analog FM1216ME/I MK3 too.
Quoted 9 lines
This is photos of analog MK3. Not so good, sorry.
Quoted 3 lines
Good decision, it are still the best tuners for analog and digital I have around, but can't talk for Secam D/K. I wonder about missing complaints during the last four years.
Our customers watch TV with params
saa7134 secam=d alsa=1
That depends on how up to date the app is, once selected, even per channel, you don't have to do this ever again and don't need any insmod options at all currently.
I recently tried to keep it for others the same :)
Umm, for the analog only FM1216ME/ I H-3 (MK3) it seems you have some other stuff on it employed. On a first look ;)
Cheers,
Hermann
Am Donnerstag, den 14.05.2009, 03:10 +0200 schrieb hermann pitton:
Quoted 1 line
Hi Dmitry :)
[snip]
Quoted 9 lines
That depends on how up to date the app is, once selected, even per channel, you don't have to do this ever again and don't need any insmod options at all currently.
I recently tried to keep it for others the same :)
Umm, for the analog only FM1216ME/ I H-3 (MK3) it seems you have some other stuff on it employed. On a first look ;)
Dmitry,
any news on that?
I don't want to hinder you to do improvements, but what about this SAW filters?
Are they really approved to have a Philips label on the tuner?
The hand/foot ;) painted claimed performance statistics don't look like that.
Am I wrong?
Cheers,
Hermann
Quoted 45 lines · Dmitri Belimov
Hi,
Quoted 28 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 15 lines
Quoted 12 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 6 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
Quoted 8 lines
Quoted 2 lines
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
Quoted 7 lines
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.This is my idea for RFC about TOP AGC:
1. Add gain variable to tuner structure.
2. AddV4L2_CID_GAINcontrol to saa7134 and disable this control.
3. Add workaround tosimple_post_tunefunction for write sensitivity level to the tuner.
4. EnableV4L2_CID_GAINcontrol when module load if card is right.
Quoted 6 lines
My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
Dmitri,
Quoted 1 line
From my understanding the take over point is the signal strength level
that you want the second stage (an IF demod chip like the TDA9887) to take over automatic gain control from the first stage (a tuner chip like the TUA6030). The objective is to set the TOP to achieve maximum gain in the first stage while avoiding clipping in the first stage. When the input signal level is smaller than the TOP, the first stage gain is at a maximum, and the second stage is performing automatic gain control internally. When the input signal level becomes greater than the TOP, the first stage gain needs to be reduced by an AGC, and the second stage gain remains constant.
As I understand it, it would be best to set the first stage (TUA6030 or similar) to "External AGC" and set the take over point in the second stage (the TDA9887), if the pins between the chips are wired up properly inside the tuner. This should coordinate the AGC in both the first stage and second stage of the tuner, as the second stage will be providing the gain control to the first stage as needed when the signal reaches the TOP.
http://www.comsec.com/usrp/microtune/NF_tutorial.pdf
It allows you to achieve maximum gain in the first stage to minimize overall receiver noise figure, and avoid clipping the input signal in the first stage (TUA6030) with a proper TOP setting in the second stage (TDA9887). The TOP setting in the second stage needs to take into account IF SAW filter attenuation of course.
Do the circuit board traces in the FM1216ME_MK3 support the TDA9887 controlling the gain of the first stage? (I've never opened an equivalent NTSC tuner assembly to take a look.)
If not, then, if I understand things correctly, you need to set the first stage and second stage TOP settings so that they refer to about the same signal level before the IF SAW filter.
I would think AGC TOP settings, for both stages of the tuner, are tuner-dependent and relatively constant once you figure out what they should be.
Do you have a different understanding or insight?
Regards,
Andy
Quoted 301 lines
If TV card is not touch
V4L2_CTRL_FLAG_DISABLEDin this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-simple.clinux/drivers/media/common/tuners/tuner-simple.c +49
-1@@ -116,6 +116,7 @@u32 frequency;u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */ @@ -495,15 +507,57 @@ "(should be 4)\n", rc);break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */ +switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + +tuner_dbg ("tv 0x%02x 0x%02x 0x%02x 0x%02x\n" , + buffer[0 ], buffer[1 ], buffer[2 ], buffer[3 ]); + + rc =tuner_i2c_xfer_send (&priv->i2c_props, buffer,4 ); +if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-cards.clinux/drivers/media/video/saa7134/saa7134-cards.c +12
-0@@ -6506,6 +6806,20 @@saa_call_all (dev, tuner, s_config, &tea5767_cfg);break ; } +case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ) {/* BUG here */ +/* enable this control */ + ctl->flags &= ~(V4L2_CTRL_FLAG_DISABLED ); + } + } }/* switch() */ saa7134_tuner_setup (dev);diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-video.clinux/drivers/media/video/saa7134/saa7134-video.c +17
-0@@ -417,6 +417,15 @@ .step = 1, .default_value = 0, .type = V4L2_CTRL_TYPE_INTEGER, + }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type = V4L2_CTRL_TYPE_INTEGER, + .flags = V4L2_CTRL_FLAG_DISABLED, },{ .id = V4L2_CID_HFLIP, .name = "Mirror",@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST : dev->ctl_contrast = c->value;@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id (V4L2_CID_BRIGHTNESS )->default_value; dev->ctl_contrast =ctrl_by_id (V4L2_CID_CONTRAST )->default_value; dev->ctl_hue =ctrl_by_id (V4L2_CID_HUE )->default_value; + dev->ctl_gain =ctrl_by_id (V4L2_CID_GAIN )->default_value; dev->ctl_saturation =ctrl_by_id (V4L2_CID_SATURATION )->default_value; dev->ctl_volume =ctrl_by_id (V4L2_CID_AUDIO_VOLUME )->default_value; dev->ctl_mute =1 ;// ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value; diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134.hlinux/drivers/media/video/saa7134/saa7134.h +1
-0@@ -548,6 +558,7 @@int ctl_bright;int ctl_contrast;int ctl_hue; +int ctl_gain;/* gain */ int ctl_saturation;int ctl_freq;int ctl_mute;/* audio */ With my best regards, Dmitry.
Quoted 144 lines
Cheers,
HermannQuoted 139 lines
With my best regards, Dmitry.
Quoted 137 lines
Cheers,
Mauro.Quoted 17 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++ b/linux/drivers/media/common/tuners/tuner-types.c Tue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static struct
tuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 110 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
With my best regards, Dmitry.
Quoted 104 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 9 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyCheers,
Mauro
Am Mittwoch, den 29.04.2009, 21:14 -0400 schrieb Andy Walls:
Quoted 83 lines · Dmitri Belimov
Quoted 45 lines
Hi,
Quoted 28 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 15 lines
Quoted 12 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 6 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
Quoted 8 lines
Quoted 2 lines
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
You mark patch with TOP AGC not this.
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
Quoted 7 lines
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.This is my idea for RFC about TOP AGC:
1. Add gain variable to tuner structure.
2. AddV4L2_CID_GAINcontrol to saa7134 and disable this control.
3. Add workaround tosimple_post_tunefunction for write sensitivity level to the tuner.
4. EnableV4L2_CID_GAINcontrol when module load if card is right.Quoted 6 lines
My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
Dmitri,
Quoted 1 line
From my understanding the take over point is the signal strength level
that you want the second stage (an IF demod chip like the TDA9887) to take over automatic gain control from the first stage (a tuner chip like the TUA6030). The objective is to set the TOP to achieve maximum gain in the first stage while avoiding clipping in the first stage. When the input signal level is smaller than the TOP, the first stage gain is at a maximum, and the second stage is performing automatic gain control internally. When the input signal level becomes greater than the TOP, the first stage gain needs to be reduced by an AGC, and the second stage gain remains constant.
As I understand it, it would be best to set the first stage (TUA6030 or similar) to "External AGC" and set the take over point in the second stage (the TDA9887), if the pins between the chips are wired up properly inside the tuner. This should coordinate the AGC in both the first stage and second stage of the tuner, as the second stage will be providing the gain control to the first stage as needed when the signal reaches the TOP.
http://www.comsec.com/usrp/microtune/NF_tutorial.pdf
It allows you to achieve maximum gain in the first stage to minimize overall receiver noise figure, and avoid clipping the input signal in the first stage (TUA6030) with a proper TOP setting in the second stage (TDA9887). The TOP setting in the second stage needs to take into account IF SAW filter attenuation of course.
Quoted 3 lines
Do the circuit board traces in the
FM1216ME_MK3support the TDA9887 controlling the gain of the first stage? (I've never opened an equivalent NTSC tuner assembly to take a look.)
"equivalent" NTSC tuners _do not_ exist at all.
I don't forget all the time we spend to find out that some of them are Intercarrier only!
Also, the tda988x stuff is underneath the tuner PCB.
I cut one off for those interested in line tracing ...
Without port2=0 you don't get any SECAM-L into the sound trap.
It needs amplification from minus 40 dB AM for the first sound carrier, and then of course you prefer the second with NICAM.
Quoted 5 lines
If not, then, if I understand things correctly, you need to set the first stage and second stage TOP settings so that they refer to about the same signal level before the IF SAW filter.
Quoted 8 lines
I would think AGC TOP settings, for both stages of the tuner, are tuner-dependent and relatively constant once you figure out what they should be.
Do you have a different understanding or insight?
Regards,
Andy
Since I have some m$ system again after 9 years, not used within the last three months, I would prefer to get it demonstrated there at first.
I leave on the first BSOD.
Cheers,
Hermann
Quoted 305 lines
Quoted 304 lines
If TV card is not touch
V4L2_CTRL_FLAG_DISABLEDin this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-simple.clinux/drivers/media/common/tuners/tuner-simple.c +49
-1@@ -116,6 +116,7 @@u32 frequency;u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */ @@ -495,15 +507,57 @@ "(should be 4)\n", rc);break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */ +switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + +tuner_dbg ("tv 0x%02x 0x%02x 0x%02x 0x%02x\n" , + buffer[0 ], buffer[1 ], buffer[2 ], buffer[3 ]); + + rc =tuner_i2c_xfer_send (&priv->i2c_props, buffer,4 ); +if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-cards.clinux/drivers/media/video/saa7134/saa7134-cards.c +12
-0@@ -6506,6 +6806,20 @@saa_call_all (dev, tuner, s_config, &tea5767_cfg);break ; } +case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ) {/* BUG here */ +/* enable this control */ + ctl->flags &= ~(V4L2_CTRL_FLAG_DISABLED ); + } + } }/* switch() */ saa7134_tuner_setup (dev);diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-video.clinux/drivers/media/video/saa7134/saa7134-video.c +17
-0@@ -417,6 +417,15 @@ .step = 1, .default_value = 0, .type = V4L2_CTRL_TYPE_INTEGER, + }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type = V4L2_CTRL_TYPE_INTEGER, + .flags = V4L2_CTRL_FLAG_DISABLED, },{ .id = V4L2_CID_HFLIP, .name = "Mirror",@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST : dev->ctl_contrast = c->value;@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id (V4L2_CID_BRIGHTNESS )->default_value; dev->ctl_contrast =ctrl_by_id (V4L2_CID_CONTRAST )->default_value; dev->ctl_hue =ctrl_by_id (V4L2_CID_HUE )->default_value; + dev->ctl_gain =ctrl_by_id (V4L2_CID_GAIN )->default_value; dev->ctl_saturation =ctrl_by_id (V4L2_CID_SATURATION )->default_value; dev->ctl_volume =ctrl_by_id (V4L2_CID_AUDIO_VOLUME )->default_value; dev->ctl_mute =1 ;// ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value; diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134.hlinux/drivers/media/video/saa7134/saa7134.h +1
-0@@ -548,6 +558,7 @@int ctl_bright;int ctl_contrast;int ctl_hue; +int ctl_gain;/* gain */ int ctl_saturation;int ctl_freq;int ctl_mute;/* audio */ With my best regards, Dmitry.
Quoted 144 lines
Cheers,
HermannQuoted 139 lines
With my best regards, Dmitry.
Quoted 137 lines
Cheers,
Mauro.Quoted 17 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++ b/linux/drivers/media/common/tuners/tuner-types.c Tue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static struct
tuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 110 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
With my best regards, Dmitry.
Quoted 104 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 18 lines · Dmitri Belimov
Hi Andy
Quoted 10 lines
Dmitri,
Quoted 5 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle band the sensitivity of receiver not good. If we switch to higher band, sensitivity more better. Hardware trick.
Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 5 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 9 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyCheers,
Mauro
Guys,
[snip]
Quoted 5 lines
Quoted 4 lines
Do the circuit board traces in the
FM1216ME_MK3support the TDA9887 controlling the gain of the first stage? (I've never opened an equivalent NTSC tuner assembly to take a look.)
Quoted 8 lines
"equivalent" NTSC tuners
_donot_exist at all.I don't forget all the time we spend to find out that some of them are Intercarrier only!
Also, the tda988x stuff is underneath the tuner PCB.
I cut one off for those interested in line tracing ...
still on the to do list ;)
Quoted 18 lines
Without port2=0 you don't get any SECAM-L into the sound trap.
It needs amplification from minus 40 dB AM for the first sound carrier, and then of course you prefer the second with NICAM.
Quoted 13 lines
If not, then, if I understand things correctly, you need to set the first stage and second stage TOP settings so that they refer to about the same signal level before the IF SAW filter.
I would think AGC TOP settings, for both stages of the tuner, are tuner-dependent and relatively constant once you figure out what they should be.
Do you have a different understanding or insight?
Regards,
Andy
Hartmut once offered to make contacts with colleagues at Philips Hamburg for such tuners and related tda9887 stuff.
Unfortunately he is not active on the lists currently.
If I see, how easily someone can get a patch to Andrew and disables all other SECAM stuff, again from Russia, I'm not convinced on anything from there.
I seriously doubt that those tuners are meant for fumbling on TOP RF/IF settings from user space.
Cheers,
Hermann
Quoted 11 lines · hermann pitton
Guys,
[snip]
Quoted 7 lines
Quoted 4 lines
Do the circuit board traces in the
FM1216ME_MK3support the TDA9887 controlling the gain of the first stage? (I've never opened an equivalent NTSC tuner assembly to take a look.)"equivalent" NTSC tuners
_donot_exist at all.
Quoted 8 lines
Quoted 6 lines
I don't forget all the time we spend to find out that some of them are Intercarrier only!
Also, the tda988x stuff is underneath the tuner PCB.
I cut one off for those interested in line tracing ...
still on the to do list ;)
Thanks. I hope it doesn't cost you too many wasted Euros...
Quoted 22 lines
Quoted 18 lines
Without port2=0 you don't get any SECAM-L into the sound trap.
It needs amplification from minus 40 dB AM for the first sound carrier, and then of course you prefer the second with NICAM.
Quoted 13 lines
If not, then, if I understand things correctly, you need to set the first stage and second stage TOP settings so that they refer to about the same signal level before the IF SAW filter.
I would think AGC TOP settings, for both stages of the tuner, are tuner-dependent and relatively constant once you figure out what they should be.
Do you have a different understanding or insight?
Regards,
AndyHartmut once offered to make contacts with colleagues at Philips Hamburg for such tuners and related tda9887 stuff.
Quoted 8 lines
Unfortunately he is not active on the lists currently.
If I see, how easily someone can get a patch to Andrew and disables all other SECAM stuff, again from Russia, I'm not convinced on anything from there.
I seriously doubt that those tuners are meant for fumbling on TOP RF/IF settings from user space.
The proper TOP settings should be a function of the input signal TV standard (positive modulation vs. negative modulation vs. FM radio) and the components in the tuner assembly (the IF filter for sure). Setting TOP settings from user space only makes sense for laboratory experimentation.
Linux is kind of funny in the way it breaks up the integrated assembly of an analog tuner to be handled by separate drivers: preselector and mixer/osc chip by tuner-simple; IF filter and IF demod by another module like tda9887. Really the two chips should be set with coordinated settings, taking into account the TV standard the tuner is being set to demodulate and the properties of the IF filter and external components to the IF demodulator.
The linux analog tuner drivers mostly appear to make some safe, default settings, and don't attempt to get the best performance. I'm assuming that is due to lack of data on the tuners and the tuners working well enough.
I'm glad to see Dmitri working at trying to improve analog performance.
I wish I had the proper equpment to experiment wih NTSC tiners. If I had a lab with a decent signal generator, oscilliscope, etc. I'd probably have lots of fun playing around with these tuners. :)
Regards,
Andy
Quoted 2 lines
Cheers,
Hermann
Am Freitag, den 01.05.2009, 20:52 -0400 schrieb Andy Walls:
Quoted 15 lines · hermann pitton
Quoted 14 lines
Guys,
[snip]
Quoted 10 lines
Quoted 4 lines
Do the circuit board traces in the
FM1216ME_MK3support the TDA9887 controlling the gain of the first stage? (I've never opened an equivalent NTSC tuner assembly to take a look.)"equivalent" NTSC tuners
_donot_exist at all.I don't forget all the time we spend to find out that some of them are Intercarrier only!
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Also, the tda988x stuff is underneath the tuner PCB.
I cut one off for those interested in line tracing ...
still on the to do list ;)
Thanks. I hope it doesn't cost you too many wasted Euros...
Seven years later it is just trash and i hope to provide enough for everyone ;)
Cheers,
Hermann
Quoted 67 lines
Quoted 23 lines
Quoted 19 lines
Without port2=0 you don't get any SECAM-L into the sound trap.
It needs amplification from minus 40 dB AM for the first sound carrier, and then of course you prefer the second with NICAM.
Quoted 13 lines
If not, then, if I understand things correctly, you need to set the first stage and second stage TOP settings so that they refer to about the same signal level before the IF SAW filter.
I would think AGC TOP settings, for both stages of the tuner, are tuner-dependent and relatively constant once you figure out what they should be.
Do you have a different understanding or insight?
Regards,
AndyHartmut once offered to make contacts with colleagues at Philips Hamburg for such tuners and related tda9887 stuff.
Quoted 8 lines
Unfortunately he is not active on the lists currently.
If I see, how easily someone can get a patch to Andrew and disables all other SECAM stuff, again from Russia, I'm not convinced on anything from there.
I seriously doubt that those tuners are meant for fumbling on TOP RF/IF settings from user space.
The proper TOP settings should be a function of the input signal TV standard (positive modulation vs. negative modulation vs. FM radio) and the components in the tuner assembly (the IF filter for sure). Setting TOP settings from user space only makes sense for laboratory experimentation.
Linux is kind of funny in the way it breaks up the integrated assembly of an analog tuner to be handled by separate drivers: preselector and mixer/osc chip by tuner-simple; IF filter and IF demod by another module like tda9887. Really the two chips should be set with coordinated settings, taking into account the TV standard the tuner is being set to demodulate and the properties of the IF filter and external components to the IF demodulator.
The linux analog tuner drivers mostly appear to make some safe, default settings, and don't attempt to get the best performance. I'm assuming that is due to lack of data on the tuners and the tuners working well enough.
I'm glad to see Dmitri working at trying to improve analog performance.
I wish I had the proper equpment to experiment wih NTSC tiners. If I had a lab with a decent signal generator, oscilliscope, etc. I'd probably have lots of fun playing around with these tuners. :)
Regards,
AndyQuoted 2 lines
Cheers,
Hermann
Am Samstag, den 02.05.2009, 04:05 +0200 schrieb hermann pitton:
Quoted 18 lines
Am Freitag, den 01.05.2009, 20:52 -0400 schrieb Andy Walls:
Quoted 17 lines · hermann pitton
Quoted 16 lines
Guys,
[snip]
Quoted 12 lines
Quoted 4 lines
Do the circuit board traces in the
FM1216ME_MK3support the TDA9887 controlling the gain of the first stage? (I've never opened an equivalent NTSC tuner assembly to take a look.)"equivalent" NTSC tuners
_donot_exist at all.I don't forget all the time we spend to find out that some of them are Intercarrier only!
Also, the tda988x stuff is underneath the tuner PCB.
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
Quoted 1 line
I cut one off for those interested in line tracing ...
still on the to do list ;)
Thanks. I hope it doesn't cost you too many wasted Euros...
Seven years later it is just trash and i hope to provide enough for everyone ;)
Andy,
did cut out my old one after lunch and have already acceptable picture quality under daylight conditions for the not yet seen backside.
For the surface with the tin compartments I must either find my old pictures sent to Gunther again or make some new with setting some lights to avoid harsh shadows.
If I'm done, and nobody has objections, I plan to send to you, Mauro, Hans and Hartmut off list.
Also to Dmitri, maybe he has a newer revision, and to CityK and Gunther for documentation.
Cheers,
Hermann
Quoted 62 lines
Quoted 62 lines
Quoted 23 lines
Quoted 19 lines
Without port2=0 you don't get any SECAM-L into the sound trap.
It needs amplification from minus 40 dB AM for the first sound carrier, and then of course you prefer the second with NICAM.
Quoted 13 lines
If not, then, if I understand things correctly, you need to set the first stage and second stage TOP settings so that they refer to about the same signal level before the IF SAW filter.
I would think AGC TOP settings, for both stages of the tuner, are tuner-dependent and relatively constant once you figure out what they should be.
Do you have a different understanding or insight?
Regards,
AndyHartmut once offered to make contacts with colleagues at Philips Hamburg for such tuners and related tda9887 stuff.
Quoted 8 lines
Unfortunately he is not active on the lists currently.
If I see, how easily someone can get a patch to Andrew and disables all other SECAM stuff, again from Russia, I'm not convinced on anything from there.
I seriously doubt that those tuners are meant for fumbling on TOP RF/IF settings from user space.
The proper TOP settings should be a function of the input signal TV standard (positive modulation vs. negative modulation vs. FM radio) and the components in the tuner assembly (the IF filter for sure). Setting TOP settings from user space only makes sense for laboratory experimentation.
Linux is kind of funny in the way it breaks up the integrated assembly of an analog tuner to be handled by separate drivers: preselector and mixer/osc chip by tuner-simple; IF filter and IF demod by another module like tda9887. Really the two chips should be set with coordinated settings, taking into account the TV standard the tuner is being set to demodulate and the properties of the IF filter and external components to the IF demodulator.
The linux analog tuner drivers mostly appear to make some safe, default settings, and don't attempt to get the best performance. I'm assuming that is due to lack of data on the tuners and the tuners working well enough.
I'm glad to see Dmitri working at trying to improve analog performance.
I wish I had the proper equpment to experiment wih NTSC tiners. If I had a lab with a decent signal generator, oscilliscope, etc. I'd probably have lots of fun playing around with these tuners. :)
Regards,
Andy
Hi Andy
Sorry me delay. I discuss about it with our programmer.
Quoted 87 lines · Dmitri Belimov
Quoted 47 lines
Hi,
Quoted 29 lines
Am Dienstag, den 28.04.2009, 19:59 +1000 schrieb Dmitri Belimov:
Quoted 19 lines
Quoted 7 lines · On Tue, 28 Apr 2009 15:18:32 -0300 Mauro Carvalho Chehab…
Quoted 4 lines · On Mon, 27 Apr 2009 19:29:05 +1000 Dmitri Belimov <[email protected]> wrote:
Hi All
Step by step.
Quoted 8 lines
Quoted 2 lines
This is patch for change only range of
FM1216ME_MK3. Slow tunning is not a big problem.Dmitri,
I'll mark those patches as RFC at patchwork until the end of those discussions. After that, please send it again into a new thread.
Quoted 5 lines
You mark patch with TOP AGC not this.
I think need discuss about
FM1216ME_MK3because I'll have a big patch for support control TOP AGC (sensitivity) of this tuner. It can be bad for compatible tuners.hmm, in Europe, that TOP AGC did not ever made much difference and it is an insmod option since ever.
Quoted 7 lines
I can't tell for Sibiria and initially that tuner had no SECAM-DK support officially at all. There are no good/much_better tuners for FTA at all and never have been ;)
Some examples, user success reports, to make it more easily to understand? I think it can only change some
_verylittle_under already worst conditions.This is my idea for RFC about TOP AGC:
1. Add gain variable to tuner structure.
2. AddV4L2_CID_GAINcontrol to saa7134 and disable this control.
3. Add workaround tosimple_post_tunefunction for write sensitivity level to the tuner. 4. EnableV4L2_CID_GAINcontrol when module load if card is right.Quoted 7 lines
My expirience not so good, step 4 segfault the kernel. How to we can make it?
Our windows end-user programm control the sensitivity of each TV channel and change when channel changed.
What you think about it??
Dmitri,
Quoted 2 lines
From my understanding the take over point is the signal strength level
that you want the second stage (an IF demod chip like the TDA9887) to take over automatic gain control from the first stage (a tuner chip like the TUA6030). The objective is to set the TOP to achieve maximum gain in the first stage while avoiding clipping in the first stage. When the input signal level is smaller than the TOP, the first stage gain is at a maximum, and the second stage is performing automatic gain control internally. When the input signal level becomes greater than the TOP, the first stage gain needs to be reduced by an AGC, and the second stage gain remains constant.
As I understand it, it would be best to set the first stage (TUA6030 or similar) to "External AGC" and set the take over point in the second stage (the TDA9887), if the pins between the chips are wired up properly inside the tuner. This should coordinate the AGC in both the first stage and second stage of the tuner, as the second stage will be providing the gain control to the first stage as needed when the signal reaches the TOP.
http://www.comsec.com/usrp/microtune/NF_tutorial.pdf
It allows you to achieve maximum gain in the first stage to minimize overall receiver noise figure, and avoid clipping the input signal in the first stage (TUA6030) with a proper TOP setting in the second stage (TDA9887). The TOP setting in the second stage needs to take into account IF SAW filter attenuation of course.
Quoted 7 lines
Do the circuit board traces in the
FM1216ME_MK3support the TDA9887 controlling the gain of the first stage? (I've never opened an equivalent NTSC tuner assembly to take a look.)If not, then, if I understand things correctly, you need to set the first stage and second stage TOP settings so that they refer to about the same signal level before the IF SAW filter.
You are right. My patch set AGC TOP level for RF signal in TUA6030.
The TOP of TDA9887 control only IF signal.
If set high level of AGC TOP for RF and RF signal is strengh, we can see white horizontal junk on TV image. For removing this junk need reduce AGC TOP RF for this channel. It can be only with Secam channels.
With my best regards, Dmitry.
Quoted 328 lines
I would think AGC TOP settings, for both stages of the tuner, are tuner-dependent and relatively constant once you figure out what they should be.
Do you have a different understanding or insight?
Regards,
AndyQuoted 314 lines
If TV card is not touch
V4L2_CTRL_FLAG_DISABLEDin this control. The programm can't change AGC TOP. And write default value to AGC TOP like now.diff -r
43dbc8ebb5a2linux/drivers/media/common/tuners/tuner-simple.c---a/linux/drivers/media/common/tuners/tuner-simple.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/common/tuners/tuner-simple.cTue Apr
21 09:44:38 2009 +1000 @@ -116,6 +116,7 @@ u32 frequency;linux/drivers/media/common/tuners/tuner-simple.c +1
-1u32 bandwidth; +signed int gain; };/* ---------------------------------------------------------------------- */ @@ -495,15 +507,57 @@ "(should be 4)\n", rc);
linux/drivers/media/common/tuners/tuner-simple.c +40
-0break ; } +case TUNER_PHILIPS_FM1216ME_MK3 : + { + buffer[2 ] =0xDE ;/* T2 = 0, T1 = 1 and T0 = 1 */ +switch (priv->gain) { +case 0 : +/* TOP = External AGC, ATC = OFF */ + buffer[3 ] =0x60 ; +break ; +case 1 : +/* TOP = 118 dB, ATC = OFF */ + buffer[3 ] =0x00 ; +break ; +case 2 : +/* TOP = 115 dB, ATC = OFF */ + buffer[3 ] =0x10 ; +break ; +case 3 : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; +case 4 : +/* TOP = 109 dB, ATC = OFF */ + buffer[3 ] =0x30 ; +break ; +case 5 : +/* TOP = 106 dB, ATC = OFF */ + buffer[3 ] =0x40 ; +break ; +case 6 : +/* TOP = 103 dB, ATC = OFF */ + buffer[3 ] =0x50 ; +break ; +default : +/* TOP = 112 dB, ATC = OFF */ + buffer[3 ] =0x20 ; +break ; + } + + tuner_dbg("tv 0x%02x 0x%02x 0x%02x 0x%02x\n", + buffer[0], buffer[1], buffer[2],buffer[3]); +
(quoted diff) +1
-0+ rc = tuner_i2c_xfer_send(&priv->i2c_props, buffer,4);
linux/drivers/media/common/tuners/tuner-simple.c +6
-1+if (4 != rc) +tuner_warn ("i2c i/o error: rc == %d " +"(should be 4)\n" , rc); + +break ; } - + }return 0 ; }diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-cards.c---a/linux/drivers/media/video/saa7134/saa7134-cards.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-cards.cTue Apr
21 09:44:38 2009 +1000 @@ -6506,6 +6806,20 @@saa_call_all(dev, tuner, s_config, &tea5767_cfg); break; }linux/drivers/media/video/saa7134/saa7134-cards.c +8
-0+case SAA7134_BOARD_BEHOLD_M6_EXTRA : + { +struct v4l2_queryctrl *ctl; +struct saa7134_fh *fh; +struct file *fl; + + ctl->id =V4L2_CID_GAIN ; +if (saa7134_queryctrl (fl, fh, ctl) ==0 ){ /* BUG here */
linux/drivers/media/video/saa7134/saa7134-cards.c +4
-0+/* enable this control */ + ctl->flags &= ~(V4L2_CTRL_FLAG_DISABLED ); + } + } }/* switch() */ saa7134_tuner_setup (dev);diff -r
43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134-video.c---a/linux/drivers/media/video/saa7134/saa7134-video.cTue Jan
27 23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134-video.cTue Apr
21 09:44:38 2009 +1000 @@ -417,6 +417,15 @@ .step =
1, .default_value = 0, .type =V4L2_CTRL_TYPE_INTEGER,linux/drivers/media/video/saa7134/saa7134-video.c +16
-0+ }, { + .id = V4L2_CID_GAIN, + .name = "Gain", + .minimum = 0, + .maximum = 6, + .step = 1, + .default_value = 3, + .type = V4L2_CTRL_TYPE_INTEGER, + .flags = V4L2_CTRL_FLAG_DISABLED, },{ .id = V4L2_CID_HFLIP, .name = "Mirror",@@ -1129,6 +1138,9 @@case V4L2_CID_HUE : c->value = dev->ctl_hue;break ; +case V4L2_CID_GAIN : + c->value = dev->ctl_gain; +break ;case V4L2_CID_CONTRAST : c->value = dev->ctl_contrast;break ;@@ -1214,6 +1226,10 @@case V4L2_CID_HUE : dev->ctl_hue = c->value;saa_writeb (SAA7134_DEC_CHROMA_HUE , dev->ctl_hue); +break ; +case V4L2_CID_GAIN : + dev->ctl_gain = c->value; +break ;case V4L2_CID_CONTRAST : dev->ctl_contrast = c->value;@@ -2502,6 +2518,7 @@ dev->ctl_bright =ctrl_by_id(V4L2_CID_BRIGHTNESS)->default_value;
dev->ctl_contrast= ctrl_by_id(V4L2_CID_CONTRAST)->default_value;dev->ctl_hue= ctrl_by_id(V4L2_CID_HUE)->default_value;(quoted diff) +1
-0+ dev->ctl_gain =ctrl_by_id(V4L2_CID_GAIN)->default_value;
dev->ctl_saturation= ctrl_by_id(V4L2_CID_SATURATION)->default_value;dev->ctl_volume= ctrl_by_id(V4L2_CID_AUDIO_VOLUME)->default_value;dev->ctl_mute= 1; //
ctrl_by_id(V4L2_CID_AUDIO_MUTE)->default_value; diff -r43dbc8ebb5a2linux/drivers/media/video/saa7134/saa7134.h---a/linux/drivers/media/video/saa7134/saa7134.hTue Jan 27
23:47:50 2009 -0200 +++b/linux/drivers/media/video/saa7134/saa7134.hTue Apr 21
09:44:38 2009 +1000 @@ -548,6 +558,7 @@ intctl_bright; intctl_contrast;
intctl_hue;linux/drivers/media/video/saa7134/saa7134.h +1
-0+int ctl_gain;/* gain */ int ctl_saturation;int ctl_freq;int ctl_mute;/* audio */
With my best regards, Dmitry.
Quoted 150 lines
Cheers,
HermannQuoted 145 lines
With my best regards, Dmitry.
Quoted 143 lines
Cheers,
Mauro.Quoted 17 lines
diff -r
b40d628f830dlinux/drivers/media/common/tuners/tuner-types.c---a/linux/drivers/media/common/tuners/tuner-types.cFriApr 24 01:46:41 2009 -0300 +++ b/linux/drivers/media/common/tuners/tuner-types.c Tue Apr 28 03:35:42 2009 +1000 @@ -558,8 +558,8 @@ static struct
tuner_rangetuner_fm1216me_mk3_pal_ranges[] = { { 16 * 158.00 /*MHz*/,0x8e,0x01, },(quoted diff) +2
-2- { 16 * 442.00 /*MHz*/, 0x8e, 0x02, }, - { 16 * 999.99 , 0x8e, 0x04, }, + { 16 * 441.00 /*MHz*/, 0x8e, 0x02, }, + { 16 * 864.00 , 0x8e, 0x04, }, }; static struct tuner_params tuner_fm1216me_mk3_params[] = {Quoted 116 lines
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
With my best regards, Dmitry.
Quoted 110 lines
Hi Dmitri,
Thank you for you responses.
Just a few more comments...
Quoted 21 lines · Dmitri Belimov
Hi Andy
Quoted 12 lines
Dmitri,
Quoted 6 lines · Dmitri Belimov
Hi All
1. Change middle band. In the end of the middle
band the sensitivity of receiver not good. If we
switch to higher band, sensitivity more better.
Hardware trick.Several years a go your customers write some messages about bad quality of TV if frequency of TV is the end of band. It can be low band or middle. Our hardware engeneer make some tests with hardware TV generator and our TV tuners.
Quoted 6 lines
If we set default frequency range for low and middle band, quality of TV signal on 159MHz and 442 MHz is bad. When we make our changes with moving end of bands the quality of TV much better. And our system programmer for OS Windows use changed bands for drivers. Customers be happy.
OK. A properly run experiment wins over theory every time. :)
Quoted 3 lines
You can test it if in your placement available TV programm on 159MHz or 442MHz. This trick can be usefull for other tuners.
If you look at
tveeprom.c, a number of other tuners are using that tuner definition:$ grep FM1216ME_MK3 tveeprom.c { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216 ME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S001D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "LG S701D MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FQ1216LME MK3"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MFPE05 2"}, { TUNER_PHILIPS_FM1216ME_MK3, "TCL MPE05-2"}, { TUNER_PHILIPS_FM1216ME_MK3, "Philips FM1216ME MK5"},If your change makes things bad for the other tuners, we'll probably have to create an alternate entry for the other tuners instead of using the
FM1216ME_MK3defintion. I suspect most of them are clones of the FM1216ME MK3 however, so it probably won't matter.Quoted 9 lines
Quoted 8 lines
Quoted 1 line
3. Set charge pump bit
This will improve the time to initially tune to a frequency, but will likely add some noise as the PLL continues to maintain lock on the signal. If there is no way to turn off the CP after the lock bit is set in the tuner, it's probably better to leave it off for lower noise and just live with slower tuning.
Quoted 3 lines
We discuss with our windows system programmer about it. He sad that in analog TV mode noise from PLL don't give any problem.
I would be concerned about phase noise affecting the colors or any FM sound carriers. If the noise isn't noticably affecting colors to the human eye (do color bars look OK?), or sound to the human ear, then OK.
Quoted 2 lines
But in digital TV mode
noise from PLL decreased BER.I thought the FM1216ME MK3 was an analog only tuner. I guess I don't know DVB-T or cable in Europe well enough.
Quoted 8 lines
Quoted 6 lines
Leaving the CP bit set should be especially noticable ad FM noise when set to tune to FM radio stations. From the
FM1236ME_MK3datasheet: "It is recommended to set CP=0 in the FM mode at all times." But the VHF low band control byte is also used when setting FM radio (AFAICT with a quick look at the code.)Yes. You are right. We can swith CP off in FM mode.
OK. Thank you.
Quoted 1 line
With my best regards, Dmitry.
Regards,
AndyCheers,
Mauro