Skip to contentSkip to conversation

dm355 evm support (v3)

PATCH New David Brownell 2 participants 2 messages May 12, 2009 Kbuild

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 dm355 evm support (v3)

From: David Brownell <[email protected]>

Initial U-Boot support for the DaVinci DM355 EVM. This is a board from Spectrum Digital. Board docs include schematic and firmware for its microcontroller:

http://c6000.spectrumdigital.com/evmdm355/revd/

Most of the DM355 chip is fully documented by TI, the most notable exception being the MPEG/JPEG coprocessor (programmable using codecs available at no cost from TI), which is omitted from its DM335 sibling:

http://focus.ti.com/docs/prod/folders/print/tms320dm355.html

This version can boot from the on-board DM9000 Ethernet chip, after being loaded (from NAND, MMC/SD, or UART). In the near future, NAND and USB support could be added ... NAND support is being held back until the support for the 4-bit ECC hardware is ready.

---
NOTE: presumes the rework of chipselect handling in the NAND code, but that will only be visible if someone enables that driver.

 MAKEALL                            |    1 
 Makefile                           |    3 
 board/davinci/dm355evm/Makefile    |   52 +++++++++
 board/davinci/dm355evm/config.mk   |   11 ++
 board/davinci/dm355evm/dm355evm.c  |  108 +++++++++++++++++++
 include/configs/davinci_dm355evm.h |  190 +++++++++++++++++++++++++++++++++++
 6 files changed, 365 insertions(+)
MAKEALL +1 -0
@@ -527,6 +527,7 @@ LIST_ARM9="			\
 	davinci_schmoogie	\
 	davinci_sffsdr		\
 	davinci_sonata		\
+	davinci_dm355evm	\
 "
 
 #########################################################################
Makefile +3 -0
@@ -2790,6 +2790,9 @@ davinci_sffsdr_config :	unconfig
 davinci_sonata_config :	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs sonata davinci davinci
 
+davinci_dm355evm_config :	unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm926ejs dm355evm davinci davinci
+
 lpd7a400_config \
 lpd7a404_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm lh7a40x lpd7a40x
board/davinci/dm355evm/Makefile new file +52 -0

52 lines not on this page · raw message

board/davinci/dm355evm/config.mk new file +11 -0
@@ -0,0 +1,11 @@
+#
+# Spectrum Digital DM355 EVM board
+#	dm355evm board has 1 bank of 128 MB DDR RAM
+#	Physical Address: 8000'0000 to 8800'0000
+#
+# Linux Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+#
+
+#Provide at least 16MB spacing between us and the Linux Kernel image
+TEXT_BASE = 0x81080000
board/davinci/dm355evm/dm355evm.c new file +108 -0

108 lines not on this page · raw message

include/configs/davinci_dm355evm.h new file +190 -0

190 lines not on this page · raw message

#1 lore raw

PATCH 1/1 dm355 evm support (v3)

Quoted 14 lines · David Brownell

From: David Brownell <[email protected]>

Initial U-Boot support for the DaVinci DM355 EVM. This is a board from Spectrum Digital. Board docs include schematic and firmware for its microcontroller:

http://c6000.spectrumdigital.com/evmdm355/revd/

Most of the DM355 chip is fully documented by TI, the most notable exception being the MPEG/JPEG coprocessor (programmable using codecs available at no cost from TI), which is omitted from its DM335 sibling:

http://focus.ti.com/docs/prod/folders/print/tms320dm355.html

Quoted 7 lines

This version can boot from the on-board DM9000 Ethernet chip, after being loaded (from NAND, MMC/SD, or UART). In the near future, NAND and USB support could be added ... NAND support is being held back until the support for the 4-bit ECC hardware is ready.

---

Applied to arm/next

Best Regards,
J.