lis3: add click function
PATCH 1/1 lis3: add click function
The LIS3 accelerometer chip has a 'click' feature which can be used to detect sudden motion on any of the three axis. Configuration data is passed via spi platform_data and no action is taken if that's not specified, so it won't harm any existing platform.
To make the configuration effective, the IRQ lines need to be set up appropriately. This patch also adds a way to do that from board support code.
The DD_* definitions were removed because I couldn't find any reference of them in the datasheet and the overlapped with the CLICK_ register space.
--- drivers/hwmon/lis3lv02d.c | 20 ++++++++++++++++++++ drivers/hwmon/lis3lv02d.h | 18 +++++++++++------- drivers/hwmon/lis3lv02d_spi.c | 17 +++++++++-------- include/linux/lis3lv02d.h | 36 ++++++++++++++++++++++++++++++++++++ 4 files changed, 76 insertions(+), 15 deletions(-) create mode 100644 include/linux/lis3lv02d.h
drivers/hwmon/lis3lv02d.c +20 -0
@@ -495,6 +495,26 @@ int lis3lv02d_init_device(struct lis3lv02d *dev)printk ("lis3_init_device: irq %d\n" , dev->irq); +/* passing in platform specific data is purely optional and only +* used by the SPI transport layer at the moment */ +if (dev->pdata) { +struct lis3lv02d_platform_data *p = dev->pdata; + +if (p->click_flags) { + dev->write (dev,CLICK_CFG , p->click_flags); + dev->write (dev,CLICK_TIMELIMIT , p->click_time_limit); + dev->write (dev,CLICK_LATENCY , p->click_latency); + dev->write (dev,CLICK_WINDOW , p->click_window); + dev->write (dev,CLICK_THSZ , p->click_thresh_z &0xf ); + dev->write (dev,CLICK_THSY_X , + (p->click_thresh_x &0xf ) | + (p->click_thresh_y <<4 )); + } + +if (p->irq_cfg) + dev->write (dev,CTRL_REG3 , p->irq_cfg); + } +/* bail if we did not get an IRQ from the bus layer */ if (!dev->irq) { printk(KERN_ERR DRIVER_NAME
drivers/hwmon/lis3lv02d.h +11 -7
@@ -27,6 +27,8 @@* They can also be connected via I²C. */ +#include <linux/lis3lv02d.h> +/* 2-byte registers */ #define LIS_DOUBLE_ID 0x3A/* LIS3LV02D[LQ] */ /* 1-byte registers */
@@ -60,13 +62,13 @@ enum lis3lv02d_reg {FF_WU_THS_L =0x34 ,FF_WU_THS_H =0x35 ,FF_WU_DURATION =0x36 , -DD_CFG =0x38 , -DD_SRC =0x39 , -DD_ACK =0x3A , -DD_THSI_L =0x3C , -DD_THSI_H =0x3D , -DD_THSE_L =0x3E , - DD_THSE_H = 0x3F, +CLICK_CFG =0x38 , +CLICK_SRC =0x39 , +CLICK_THSY_X =0x3B , +CLICK_THSZ =0x3C , +CLICK_TIMELIMIT =0x3D , +CLICK_LATENCY =0x3E , + CLICK_WINDOW = 0x3F, }; enum lis3lv02d_ctrl1 {
@@ -185,6 +187,8 @@ struct lis3lv02d {struct fasync_struct *async_queue;/* queue for the misc device */ wait_queue_head_t misc_wait;/* Wait queue for the misc device */ unsigned long misc_opened;/* bit0: whether the device is open */ + +struct lis3lv02d_platform_data *pdata;/* for passing board config */ };int lis3lv02d_init_device (struct lis3lv02d *lis3);
drivers/hwmon/lis3lv02d_spi.c +9 -8
@@ -66,21 +66,22 @@ static int __devinit lis302dl_spi_probe(struct spi_device *spi)if (ret <0 )return ret; - lis3_dev.bus_priv = spi; - lis3_dev.init = lis3_spi_init; - lis3_dev.read = lis3_spi_read; - lis3_dev.write = lis3_spi_write; - lis3_dev.irq = spi->irq; - lis3_dev.ac = lis3lv02d_axis_normal; + lis3_dev.bus_priv = spi; + lis3_dev.init = lis3_spi_init; + lis3_dev.read = lis3_spi_read; + lis3_dev.write = lis3_spi_write; + lis3_dev.irq = spi->irq; + lis3_dev.ac = lis3lv02d_axis_normal; + lis3_dev.pdata = spi->dev.platform_data;spi_set_drvdata (spi, &lis3_dev); - ret =lis3lv02d_init_device (&lis3_dev); -return ret; +return lis3lv02d_init_device (&lis3_dev); } static int __devexit lis302dl_spi_remove(struct spi_device *spi) {struct lis3lv02d *lis3 =spi_get_drvdata (spi); +lis3lv02d_joystick_disable ();lis3lv02d_poweroff (lis3);return 0 ;
include/linux/lis3lv02d.h new file +36 -0
@@ -0,0 +1,36 @@ +#ifndef __LIS3LV02D_H_ +#define __LIS3LV02D_H_ + +struct lis3lv02d_platform_data { +#define LIS3_CLICK_SINGLE_X (1 << 0) +#define LIS3_CLICK_DOUBLE_X (1 << 1) +#define LIS3_CLICK_SINGLE_Y (1 << 2) +#define LIS3_CLICK_DOUBLE_Y (1 << 3) +#define LIS3_CLICK_SINGLE_Z (1 << 4) +#define LIS3_CLICK_DOUBLE_Z (1 << 5) +unsigned char click_flags; +unsigned char click_thresh_x; +unsigned char click_thresh_y; +unsigned char click_thresh_z; +unsigned char click_time_limit; +unsigned char click_latency; +unsigned char click_window; + +#define LIS3_IRQ1_DISABLE (0 << 0) +#define LIS3_IRQ1_FF_WU_1 (1 << 0) +#define LIS3_IRQ1_FF_WU_2 (2 << 0) +#define LIS3_IRQ1_FF_WU_12 (3 << 0) +#define LIS3_IRQ1_DATA_READY (4 << 0) +#define LIS3_IRQ1_CLICK (7 << 0) +#define LIS3_IRQ2_DISABLE (0 << 3) +#define LIS3_IRQ2_FF_WU_1 (1 << 3) +#define LIS3_IRQ2_FF_WU_2 (2 << 3) +#define LIS3_IRQ2_FF_WU_12 (3 << 3) +#define LIS3_IRQ2_DATA_READY (4 << 3) +#define LIS3_IRQ2_CLICK (7 << 3) +#define LIS3_IRQ_OPEN_DRAIN (1 << 6) +#define LIS3_IRQ_ACTIVE_HIGH (1 << 7) +unsigned char irq_cfg; +}; + +#endif /* __LIS3LV02D_H_ */
Signature · 1 line
1.6.3.1
Quoted 9 lines · Daniel Mack
The LIS3 accelerometer chip has a 'click' feature which can be used to detect sudden motion on any of the three axis. Configuration data is passed via spi
platform_dataand no action is taken if that's not specified, so it won't harm any existing platform.To make the configuration effective, the IRQ lines need to be set up appropriately. This patch also adds a way to do that from board support code.
Quoted 7 lines
The DD_* definitions were removed because I couldn't find any reference of them in the datasheet and the overlapped with the
CLICK_register space.Signed-off-by Daniel Mack <[email protected]>Cc Pavel Machek <[email protected]>Cc Eric Piel <[email protected]>
Well, patch looks mostly okay, but it would be nice to separate cleanups onto separate patch...
Quoted 34 lines
index 07ae74b..8d50ef2 100644
drivers/hwmon/lis3lv02d_spi.c +9
-8@@ -66,21 +66,22 @@ static int __devinit lis302dl_spi_probe(struct spi_device *spi)if (ret <0 )return ret; - lis3_dev.bus_priv = spi; - lis3_dev.init = lis3_spi_init; - lis3_dev.read = lis3_spi_read; - lis3_dev.write = lis3_spi_write; - lis3_dev.irq = spi->irq; - lis3_dev.ac = lis3lv02d_axis_normal; + lis3_dev.bus_priv = spi; + lis3_dev.init = lis3_spi_init; + lis3_dev.read = lis3_spi_read; + lis3_dev.write = lis3_spi_write; + lis3_dev.irq = spi->irq; + lis3_dev.ac = lis3lv02d_axis_normal; + lis3_dev.pdata = spi->dev.platform_data;spi_set_drvdata (spi, &lis3_dev); - ret =lis3lv02d_init_device (&lis3_dev); -return ret; +return lis3lv02d_init_device (&lis3_dev); } static int __devexit lis302dl_spi_remove(struct spi_device *spi) {struct lis3lv02d *lis3 =spi_get_drvdata (spi); +lis3lv02d_joystick_disable ();lis3lv02d_poweroff (lis3);return 0 ;
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
Quoted 13 lines · Pavel Machek
Quoted 13 lines
The LIS3 accelerometer chip has a 'click' feature which can be used to detect sudden motion on any of the three axis. Configuration data is passed via spi
platform_dataand no action is taken if that's not specified, so it won't harm any existing platform.To make the configuration effective, the IRQ lines need to be set up appropriately. This patch also adds a way to do that from board support code.
The DD_* definitions were removed because I couldn't find any reference of them in the datasheet and the overlapped with the
CLICK_register space.
Quoted 6 lines
Quoted 3 lines
Signed-off-by Daniel Mack <[email protected]>Cc Pavel Machek <[email protected]>Cc Eric Piel <[email protected]>Well, patch looks mostly okay, but it would be nice to separate cleanups onto separate patch...
Yes, I've seen that, but considered the two minor things too small to deserve a seperate patch. Do you want me resend?
Daniel
Quoted 18 lines · Daniel Mack
Quoted 17 lines · Pavel Machek
Quoted 16 lines
The LIS3 accelerometer chip has a 'click' feature which can be used to detect sudden motion on any of the three axis. Configuration data is passed via spi
platform_dataand no action is taken if that's not specified, so it won't harm any existing platform.To make the configuration effective, the IRQ lines need to be set up appropriately. This patch also adds a way to do that from board support code.
The DD_* definitions were removed because I couldn't find any reference of them in the datasheet and the overlapped with the
CLICK_register space.Signed-off-by Daniel Mack <[email protected]>Cc Pavel Machek <[email protected]>Cc Eric Piel <[email protected]>
Quoted 5 lines
Quoted 2 lines
Well, patch looks mostly okay, but it would be nice to separate cleanups onto separate patch...
Yes, I've seen that, but considered the two minor things too small to deserve a seperate patch. Do you want me resend?
Well, I guess it would be best if you reverted those cleanups and resent. You can get my acked-by: on that; cc akpm.
Pavel
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
A message that is not in the archive (sent off-list or not yet received): [email protected]
Op 12-06-09 12:37, Daniel Mack schreef:
Quoted 5 lines
The LIS3 accelerometer chip has a 'click' feature which can be used to detect sudden motion on any of the three axis. Configuration data is passed via spi
platform_dataand no action is taken if that's not specified, so it won't harm any existing platform.
Quoted 7 lines
To make the configuration effective, the IRQ lines need to be set up appropriately. This patch also adds a way to do that from board support code.
The DD_* definitions were removed because I couldn't find any reference of them in the datasheet and the overlapped with the
CLICK_register space.
Hello,
It's not so simple. The driver supports both LIS302xx and LIS3LV02xx. The LIS302xx (whoami == 0x3A) has CLICK_* registers, and the LIS3LV02xx (whoami == 0x3B) has DD_* registers. So first of all, you should not remove the references to DD_*, just add the CLICK_* definitions after them. Moreover, the usage of those registers should therefore be conditioned to whoami == 0x3A.
Also, I did not follow all the black magic happening with platform_data. Could you explain how much would be needed to have the same feature in the ACPI side?
Also, it seems to only set up the "click" feature, without ever using it. How do you access this information from userspace? Is it specific to SPI? Maybe it could also generate button events in the joystick interface?
See you,
Eric
Hi Eric,
Quoted 13 lines · Éric Piel
Op 12-06-09 12:37, Daniel Mack schreef:
Quoted 5 lines
The LIS3 accelerometer chip has a 'click' feature which can be used to detect sudden motion on any of the three axis. Configuration data is passed via spi
platform_dataand no action is taken if that's not specified, so it won't harm any existing platform.Quoted 7 lines
To make the configuration effective, the IRQ lines need to be set up appropriately. This patch also adds a way to do that from board support code.
The DD_* definitions were removed because I couldn't find any reference of them in the datasheet and the overlapped with the
CLICK_register space.
Quoted 7 lines
Hello,
It's not so simple. The driver supports both LIS302xx and LIS3LV02xx. The LIS302xx (whoami ==0x3A) has CLICK_* registers, and the LIS3LV02xx (whoami ==0x3B) has DD_* registers. So first of all, you should not remove the references to DD_*, just add the CLICK_* definitions after them. Moreover, the usage of those registers should therefore be conditioned to whoami ==0x3A.
Ok, I can split the register definitions.
Quoted 3 lines
Also, I did not follow all the black magic happening with
platform_data. Could you explain how much would be needed to have the same feature in the ACPI side?
It's not so much black magic but follows the standard procedure for passing device specific data to probed SPI devices. What you find in board support code for embedded devices is a defintion of an spi_board_info struct. On my platform, it looks like this for the lis3 device:
static struct lis3lv02d_platform_data lis3_pdata = {
.click_flags = LIS3_CLICK_SINGLE_X |
LIS3_CLICK_SINGLE_Y |
LIS3_CLICK_SINGLE_Z,
.click_thresh_x = 10,
.click_thresh_y = 10,
.click_thresh_z = 10,
.irq_cfg = LIS3_IRQ1_CLICK,
LIS3_IRQ_ACTIVE_HIGH,
};static struct spi_board_info my_spi_devices[] __initdata = {
{
.modalias = "lis3lv02d_spi",
.max_speed_hz = 1000000,
.bus_num = 0,
.chip_select = 0,
.controller_data = (void *) mfp_to_gpio(GPIO_ACCEL_CS), .platform_data = &lis3_pdata,
.irq = gpio_to_irq(mfp_to_gpio(GPIO_ACCEL_IRQ)),
},
I don't know ACPI, so I can't say how a similiar abstraction could be achieved.
Quoted 3 lines
Also, it seems to only set up the "click" feature, without ever using it. How do you access this information from userspace? Is it specific to SPI? Maybe it could also generate button events in the joystick interface?
We're using the IRQ outputs of that chips directly as source to other circuity, so there is no userspace logic in the game. If anyone needs that, a simple callback function would be easy to add at some later point.
See the updated patch below.
Thanks,
Daniel
Quoted 1 line
From
17d749d1f7b9c1287cc5b8109921e7a6f149b8bcMon Sep 17 00:00:00 2001
From: Daniel Mack <[email protected]>
Date: Thu, 11 Jun 2009 21:47:10 +0200
Subject: [PATCH] lis3: add click function
The LIS302DL accelerometer chip has a 'click' feature which can be used to detect sudden motion on any of the three axis. Configuration data is passed via spi platform_data and no action is taken if that's not specified, so it won't harm any existing platform.
To make the configuration effective, the IRQ lines need to be set up appropriately. This patch also adds a way to do that from board support code.
The DD_* definitions were factored out to an own enum because they are specific to LIS3LV02D devices.
--- drivers/hwmon/lis3lv02d.c | 20 ++++++++++++++++++++ drivers/hwmon/lis3lv02d.h | 19 ++++++++++++++++++- drivers/hwmon/lis3lv02d_spi.c | 1 + include/linux/lis3lv02d.h | 39 +++++++++++++++++++++++++++++++++++++++ 4 files changed, 78 insertions(+), 1 deletions(-) create mode 100644 include/linux/lis3lv02d.h
drivers/hwmon/lis3lv02d.c +20 -0
@@ -495,6 +495,26 @@ int lis3lv02d_init_device(struct lis3lv02d *dev)printk ("lis3_init_device: irq %d\n" , dev->irq); +/* passing in platform specific data is purely optional and only +* used by the SPI transport layer at the moment */ +if (dev->pdata) { +struct lis3lv02d_platform_data *p = dev->pdata; + +if (p->click_flags && (dev->whoami ==LIS_SINGLE_ID )) { + dev->write (dev,CLICK_CFG , p->click_flags); + dev->write (dev,CLICK_TIMELIMIT , p->click_time_limit); + dev->write (dev,CLICK_LATENCY , p->click_latency); + dev->write (dev,CLICK_WINDOW , p->click_window); + dev->write (dev,CLICK_THSZ , p->click_thresh_z &0xf ); + dev->write (dev,CLICK_THSY_X , + (p->click_thresh_x &0xf ) | + (p->click_thresh_y <<4 )); + } + +if (p->irq_cfg) + dev->write (dev,CTRL_REG3 , p->irq_cfg); + } +/* bail if we did not get an IRQ from the bus layer */ if (!dev->irq) { printk(KERN_ERR DRIVER_NAME
drivers/hwmon/lis3lv02d.h +18 -1
@@ -27,12 +27,14 @@* They can also be connected via I²C. */ +#include <linux/lis3lv02d.h> +/* 2-byte registers */ #define LIS_DOUBLE_ID 0x3A/* LIS3LV02D[LQ] */ /* 1-byte registers */ #define LIS_SINGLE_ID 0x3B/* LIS[32]02DL and others */ -enum lis3lv02d_reg { +enum lis3_reg {WHO_AM_I =0x0F ,OFFSET_X =0x16 ,OFFSET_Y =0x17 ,
@@ -60,6 +62,19 @@ enum lis3lv02d_reg {FF_WU_THS_L =0x34 ,FF_WU_THS_H =0x35 , FF_WU_DURATION = 0x36, +}; + +enum lis302d_reg { +CLICK_CFG =0x38 , +CLICK_SRC =0x39 , +CLICK_THSY_X =0x3B , +CLICK_THSZ =0x3C , +CLICK_TIMELIMIT =0x3D , +CLICK_LATENCY =0x3E , +CLICK_WINDOW =0x3F , +}; + +enum lis3lv02d_reg {DD_CFG =0x38 ,DD_SRC =0x39 , DD_ACK = 0x3A,
@@ -185,6 +200,8 @@ struct lis3lv02d {struct fasync_struct *async_queue;/* queue for the misc device */ wait_queue_head_t misc_wait;/* Wait queue for the misc device */ unsigned long misc_opened;/* bit0: whether the device is open */ + +struct lis3lv02d_platform_data *pdata;/* for passing board config */ };int lis3lv02d_init_device (struct lis3lv02d *lis3);
drivers/hwmon/lis3lv02d_spi.c +1 -0
@@ -72,6 +72,7 @@ static int __devinit lis302dl_spi_probe(struct spi_device *spi) lis3_dev.write = lis3_spi_write; lis3_dev.irq = spi->irq; lis3_dev.ac = lis3lv02d_axis_normal; + lis3_dev.pdata = spi->dev.platform_data;spi_set_drvdata (spi, &lis3_dev); ret =lis3lv02d_init_device (&lis3_dev);
include/linux/lis3lv02d.h new file +39 -0
@@ -0,0 +1,39 @@ +#ifndef __LIS3LV02D_H_ +#define __LIS3LV02D_H_ + +struct lis3lv02d_platform_data { +/* please note: the 'click' feature is only supported for +* LIS[32]02DL variants of the chip and will be ignored for +* others */ +#define LIS3_CLICK_SINGLE_X (1 << 0) +#define LIS3_CLICK_DOUBLE_X (1 << 1) +#define LIS3_CLICK_SINGLE_Y (1 << 2) +#define LIS3_CLICK_DOUBLE_Y (1 << 3) +#define LIS3_CLICK_SINGLE_Z (1 << 4) +#define LIS3_CLICK_DOUBLE_Z (1 << 5) +unsigned char click_flags; +unsigned char click_thresh_x; +unsigned char click_thresh_y; +unsigned char click_thresh_z; +unsigned char click_time_limit; +unsigned char click_latency; +unsigned char click_window; + +#define LIS3_IRQ1_DISABLE (0 << 0) +#define LIS3_IRQ1_FF_WU_1 (1 << 0) +#define LIS3_IRQ1_FF_WU_2 (2 << 0) +#define LIS3_IRQ1_FF_WU_12 (3 << 0) +#define LIS3_IRQ1_DATA_READY (4 << 0) +#define LIS3_IRQ1_CLICK (7 << 0) +#define LIS3_IRQ2_DISABLE (0 << 3) +#define LIS3_IRQ2_FF_WU_1 (1 << 3) +#define LIS3_IRQ2_FF_WU_2 (2 << 3) +#define LIS3_IRQ2_FF_WU_12 (3 << 3) +#define LIS3_IRQ2_DATA_READY (4 << 3) +#define LIS3_IRQ2_CLICK (7 << 3) +#define LIS3_IRQ_OPEN_DRAIN (1 << 6) +#define LIS3_IRQ_ACTIVE_HIGH (1 << 7) +unsigned char irq_cfg; +}; + +#endif /* __LIS3LV02D_H_ */
Signature · 1 line
1.6.3.1
Éric Piel
Acked-byOp 12-06-09 14:31, Daniel Mack schreef:
:
Quoted 18 lines
It's not so much black magic but follows the standard procedure for passing device specific data to probed SPI devices. What you find in board support code for embedded devices is a defintion of an
spi_board_infostruct. On my platform, it looks like this for the lis3 device:static struct lis3lv02d_platform_data lis3_pdata = { .click_flags = LIS3_CLICK_SINGLE_X | LIS3_CLICK_SINGLE_Y | LIS3_CLICK_SINGLE_Z, .click_thresh_x = 10, .click_thresh_y = 10, .click_thresh_z = 10, .irq_cfg = LIS3_IRQ1_CLICK, LIS3_IRQ_ACTIVE_HIGH, };
Quoted 11 lines
static struct
spi_board_infomy_spi_devices[]__initdata= {
{
.modalias = "lis3lv02d_spi",
.max_speed_hz = 1000000,
.bus_num = 0,
.chip_select = 0,
.controller_data = (void *)mfp_to_gpio(GPIO_ACCEL_CS), .platform_data =&lis3_pdata,
.irq = gpio_to_irq(mfp_to_gpio(GPIO_ACCEL_IRQ)),
},
I see. So your platform is not among the one contained in the vanilla kernel? Shouldn't this above code be written somewhere so that people know about it? Some of the values do not seem especially obvious!
Quoted 11 lines
I don't know ACPI, so I can't say how a similiar abstraction could be achieved.
Quoted 3 lines
Also, it seems to only set up the "click" feature, without ever using it. How do you access this information from userspace? Is it specific to SPI? Maybe it could also generate button events in the joystick interface?
We're using the IRQ outputs of that chips directly as source to other circuity, so there is no userspace logic in the game. If anyone needs that, a simple callback function would be easy to add at some later point.
I guess that to have the functionality in ACPI, a complete handling of the interruptions, up to the generation of button events would be needed. This can be done later on, whenever someone finds the need...
Quoted 2 lines
See the updated patch below.
Looks good to me.
Quoted 6 lines
From
17d749d1f7b9c1287cc5b8109921e7a6f149b8bcMon Sep 17 00:00:00 2001
From: Daniel Mack <[email protected]>
Date: Thu, 11 Jun 2009 21:47:10 +0200
Subject: [PATCH] lis3: add click function
Thanks,
Eric
Quoted 11 lines · Éric Piel
Quoted 11 lines
static struct
spi_board_infomy_spi_devices[]__initdata= {
{
.modalias = "lis3lv02d_spi",
.max_speed_hz = 1000000,
.bus_num = 0,
.chip_select = 0,
.controller_data = (void *)mfp_to_gpio(GPIO_ACCEL_CS), .platform_data =&lis3_pdata,
.irq = gpio_to_irq(mfp_to_gpio(GPIO_ACCEL_IRQ)),
},
Quoted 3 lines
I see. So your platform is not among the one contained in the vanilla kernel? Shouldn't this above code be written somewhere so that people know about it? Some of the values do not seem especially obvious!
The platform is currently under development and will be merged at some later point. The magics above are just GPIO defintions - everything else is just the usual glue logic you add when registering an SPI device.
Quoted 7 lines
Quoted 4 lines
We're using the IRQ outputs of that chips directly as source to other circuity, so there is no userspace logic in the game. If anyone needs that, a simple callback function would be easy to add at some later point.
I guess that to have the functionality in ACPI, a complete handling of the interruptions, up to the generation of button events would be needed. This can be done later on, whenever someone finds the need...
Ack.
Quoted 1 line
Acked-by Eric Piel <[email protected]>
Thanks :)
Andrew, could you queue that one?
Daniel