perf_counters: page fault trace record
Hi,
One of the tools we are working on needs to be able to look not only at counts of page faults, but where they are occurring (ip and faulting page address).
What would you think about adding a new bit to the config record, something like:
include/linux/perf_counter.h +1 -2
@@ -167,8 +167,9 @@ struct perf_counter_attr { mmap : 1, /* include mmap data */ comm : 1, /* include comm data */ freq : 1, /* use freq, not period */ - - __reserved_2 : 53; + page_fault : 1, /* include page fault data
*/
+
+ __reserved_2 : 52;
We'd need a new event type too - PERF_EVENT_PAGE_FAULT which would have:
/*
* struct {
* struct perf_event_header header; * u64 ip; * u64 fault_address;
* };
*/
etc.
I would guess that special care would need to be taken to post an event record like this on the thread of a page fault handler.
Any objection to this idea?
Regards,
- Corey
Corey Ashford
Software Engineer
IBM Linux Technology Center, Linux Toolchain
[email protected]
Quoted 4 lines · Corey Ashford
One of the tools we are working on needs to be able to look not only at counts of page faults, but where they are occurring (ip and faulting page address).
What would you think about adding a new bit to the config record, something like:
Can't you do what you need just using a page fault software counter with sample_type = PERF_SAMPLE_IP | PERF_SAMPLE_ADDR and sample_period = 1?
Paul.
Quoted 10 lines · Paul Mackerras
Quoted 4 lines · Corey Ashford
One of the tools we are working on needs to be able to look not only at counts of page faults, but where they are occurring (ip and faulting page address).
What would you think about adding a new bit to the config record, something like:
Can't you do what you need just using a page fault software counter with
sample_type=PERF_SAMPLE_IP|PERF_SAMPLE_ADDRandsample_period= 1?
Yes, we should use a generic 'data address' field. A whole lot of interesting events can live with that - only full-blown generic tracepoints have more complex sample record formats.
Also, if this feature is added to pagefaults, please also add support for it into tools/perf/, so that it gets tested/used.
Thanks,
Ingo
Quoted 9 lines · Paul Mackerras
Quoted 3 lines · Corey Ashford
One of the tools we are working on needs to be able to look not only at counts of page faults, but where they are occurring (ip and faulting page address).
What would you think about adding a new bit to the config record, something like:
Can't you do what you need just using a page fault software counter with
sample_type=PERF_SAMPLE_IP|PERF_SAMPLE_ADDRandsample_period= 1?
I thought about that, but I was under the (incorrect?) impression that on Power, the PERF_SAMPLE_ADDR would be set by the value of the SDAR register, which wouldn't be correct for the case of a page fault.
I need to go look at the kernel code :)
- Corey
Quoted 8 lines · Corey Ashford
Quoted 3 lines · Paul Mackerras
Can't you do what you need just using a page fault software counter with
sample_type=PERF_SAMPLE_IP|PERF_SAMPLE_ADDRandsample_period= 1?I thought about that, but I was under the (incorrect?) impression that on Power, the
PERF_SAMPLE_ADDRwould be set by the value of the SDAR register, which wouldn't be correct for the case of a page fault.
No, the PERF_SAMPLE_ADDR value only comes from SDAR for a hardware counter overflow event. For the page-fault software counter the PERF_SAMPLE_ADDR value will always be the faulting address.
Paul.
Quoted 7 lines · Paul Mackerras
Quoted 5 lines · Corey Ashford
Quoted 3 lines · Paul Mackerras
Can't you do what you need just using a page fault software counter with
sample_type=PERF_SAMPLE_IP|PERF_SAMPLE_ADDRandsample_period= 1?
Quoted 8 lines
Quoted 4 lines
I thought about that, but I was under the (incorrect?) impression that on Power, the
PERF_SAMPLE_ADDRwould be set by the value of the SDAR register, which wouldn't be correct for the case of a page fault.No, the
PERF_SAMPLE_ADDRvalue only comes from SDAR for a hardware counter overflow event. For the page-fault software counter thePERF_SAMPLE_ADDRvalue will always be the faulting address.
Corey, could you please add support for it in 'perf'? We dont want such sw-counter features to be in the kernel code without matching support in tools/perf/.
While user data symbols wont be resolved, if we have a --target-address switch in perf record we could see the faulting frequency (and the fault coverage - and ordering as well) of shared libraries, in perf report and perf annotate.
This would be a very useful facility.
Thanks,
Ingo
Quoted 15 lines · Ingo Molnar
Quoted 6 lines · Paul Mackerras
Quoted 3 lines · Corey Ashford
Quoted 1 line · Paul Mackerras
Can't you do what you need just using a page fault software counter with
sample_type=PERF_SAMPLE_IP|PERF_SAMPLE_ADDRandsample_period= 1?I thought about that, but I was under the (incorrect?) impression that on Power, the
PERF_SAMPLE_ADDRwould be set by the value of the SDAR register, which wouldn't be correct for the case of a page fault.No, the
PERF_SAMPLE_ADDRvalue only comes from SDAR for a hardware counter overflow event. For the page-fault software counter thePERF_SAMPLE_ADDRvalue will always be the faulting address.Corey, could you please add support for it in 'perf'? We dont want such sw-counter features to be in the kernel code without matching support in
tools/perf/.While user data symbols wont be resolved, if we have a
--target-address switch in perf record we could see the faulting
frequency (and the fault coverage - and ordering as well) of shared libraries, in perf report and perf annotate.
Quoted 5 lines
This would be a very useful facility.
Thanks,
Ingo
I'll see what I can do. This will be my first time modifying perf, so expect that I won't do things the way you prefer the first couple of go-arounds :)
Regards,
- Corey