sky2 driver patches
Subsystems (2)
cover sky2 driver patches
The patches are ordered in importance. The first six should go into 2.6.31, the rest can wait for 2.6.32.
PATCH 1/9 sky2: turn off pause during shutdown
This unblocks the chip if it is stuck in pause cycle during shutdown.
drivers/net/sky2.c +2 -1
@@ -1808,7 +1808,8 @@ static int sky2_down(struct net_device *synchronize_irq (hw->pdev->irq); -sky2_gmac_reset (hw, port); +/* Force flow control off */ +sky2_write8 (hw,SK_REG (port,GMAC_CTRL ),GMC_PAUSE_OFF );/* Stop transmitter */ sky2_write32 (hw,Q_ADDR (txqaddr[port],Q_CSR ),BMU_STOP );
Re: [PATCH 1/9] sky2: turn off pause during shutdown
From: Stephen Hemminger <[email protected]>
Date: Wed, 17 Jun 2009 10:30:32 -0700
Quoted 4 lines
This unblocks the chip if it is stuck in pause cycle during shutdown.
Signed-off-by Stephen Hemminger <[email protected]>
Applied.
PATCH 2/9 sky2: more receive shutdown
In reply to Stephen HemmingerReset more parts of the receive path when device is take offline.
drivers/net/sky2.c +8 -1
@@ -1151,7 +1151,14 @@ stopped:/* reset the Rx prefetch unit */ sky2_write32 (hw,Y2_QADDR (rxq,PREF_UNIT_CTRL ),PREF_UNIT_RST_SET ); -mmiowb (); + +/* Reset the RAM Buffer receive queue */ +sky2_write8 (hw,RB_ADDR (rxq,RB_CTRL ),RB_RST_SET ); + +/* Reset Rx MAC FIFO */ +sky2_write8 (hw,SK_REG (sky2->port,RX_GMF_CTRL_T ),GMF_RST_SET ); + +sky2_read8 (hw,B0_CTST ); }/* Clean out receive buffer area, assumes receiver hardware stopped */
Re: [PATCH 2/9] sky2: more receive shutdown
From: Stephen Hemminger <[email protected]>
Date: Wed, 17 Jun 2009 10:30:33 -0700
Quoted 3 lines
Reset more parts of the receive path when device is take offline.
Signed-off-by Stephen Hemminger <[email protected]>
Applied.
Re: [PATCH 2/9] sky2: more receive shutdown
In reply to Stephen HemmingerQuoted 12 lines · Stephen Hemminger
Reset more parts of the receive path when device is take offline.
Signed-off-by Stephen Hemminger <[email protected]>drivers/net/sky2.c +1
-1@@ -1151,7 +1151,14 @@ stopped:/* reset the Rx prefetch unit */ sky2_write32 (hw,Y2_QADDR (rxq,PREF_UNIT_CTRL ),PREF_UNIT_RST_SET ); -mmiowb (); +
drivers/net/sky2.c stopped: · line 1164
Quoted 10 lines
drivers/net/sky2.c +7
-0+/* Reset the RAM Buffer receive queue */ +sky2_write8 (hw,RB_ADDR (rxq,RB_CTRL ),RB_RST_SET ); + +/* Reset Rx MAC FIFO */ +sky2_write8 (hw,SK_REG (sky2->port,RX_GMF_CTRL_T ),GMF_RST_SET ); + +sky2_read8 (hw,B0_CTST ); }/* Clean out receive buffer area, assumes receiver hardware stopped */
With this this patch applied, the receive on my network card does not work from boot. Git bisect identified this as the 'bad' commit and after reverting it all works properly.
Here are the entries for sky2 and eth0 from the system log for a boot with the patch enabled:-
Jun 20 06:38:25 newton sky2 driver version 1.23 Jun 20 06:38:25 newton sky2 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 Jun 20 06:38:25 newton sky2 0000:04:00.0: setting latency timer to 64 Jun 20 06:38:25 newton sky2 0000:04:00.0: Yukon-2 EC chip revision 2 Jun 20 06:38:25 newton sky2 0000:04:00.0: irq 30 for MSI/MSI-X Jun 20 06:38:25 newton sky2 eth0: addr 00:1b:fc:65:82:93 Jun 20 06:38:25 newton sky2 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jun 20 06:38:25 newton sky2 0000:03:00.0: setting latency timer to 64 Jun 20 06:38:25 newton sky2 0000:03:00.0: Yukon-2 EC chip revision 2 Jun 20 06:38:25 newton sky2 0000:03:00.0: irq 31 for MSI/MSI-X Jun 20 06:38:25 newton sky2 eth1: addr 00:1b:fc:65:7c:be Jun 20 06:38:25 newton sky2 eth0: enabling interface Jun 20 06:38:25 newton ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 20 06:38:28 newton sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both Jun 20 06:38:28 newton ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
lspci -v
03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 20)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet controller PCIe (Asus)
Flags: bus master, fast devsel, latency 0, IRQ 31
Memory at ff7fc000 (64-bit, non-prefetchable) [size=16K]
I/O ports at a800 [size=256]
Expansion ROM at ff7c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [5c] MSI: Mask- 64bit+ Count=1/2 Enable+
Capabilities: [e0] Express Legacy Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Kernel driver in use: sky2
Kernel modules: sky2
Re: [PATCH 2/9] sky2: more receive shutdown
Quoted 3 lines · Graham Murray
With this this patch applied, the receive on my network card does not work from boot. Git bisect identified this as the 'bad' commit and after reverting it all works properly.
I should add that there is no panic, BUG, oops etc, nor any other printk messages, the interface just does not work.
PATCH 3/9 sky2: PCI irq issues
In reply to Stephen HemmingerAdd some read's to avoid any PCI posting issues when controlling irq's.
drivers/net/sky2.c +2 -0
@@ -1495,6 +1495,7 @@ static int sky2_up(struct net_device *de imask =sky2_read32 (hw,B0_IMSK ); imask |= portirq_msk[port];sky2_write32 (hw,B0_IMSK , imask); +sky2_read32 (hw,B0_IMSK );sky2_set_multicast (dev);
@@ -1812,6 +1813,7 @@ static int sky2_down(struct net_device * imask =sky2_read32 (hw,B0_IMSK ); imask &= ~portirq_msk[port];sky2_write32 (hw,B0_IMSK , imask); +sky2_read32 (hw,B0_IMSK );synchronize_irq (hw->pdev->irq);
Re: [PATCH 3/9] sky2: PCI irq issues
From: Stephen Hemminger <[email protected]>
Date: Wed, 17 Jun 2009 10:30:34 -0700
Quoted 4 lines
Add some read's to avoid any PCI posting issues when controlling irq's.
Signed-off-by Stephen Hemminger <[email protected]>
Applied.
PATCH 4/9 sky2: fix shutdown synchronization
In reply to Stephen HemmingerThe logic in sky2_down was incorrect. Receiver could report status after rx_stop was called.
The steps need to be:
* stop new frames from being transmitted
* shut off transmit/receive logic
* synchronize with NAPI to process status info about transmitter and receiver
drivers/net/sky2.c +9 -5
@@ -1815,8 +1815,6 @@ static int sky2_down(struct net_device *sky2_write32 (hw,B0_IMSK , imask);sky2_read32 (hw,B0_IMSK ); -synchronize_irq (hw->pdev->irq); -/* Force flow control off */ sky2_write8 (hw,SK_REG (port,GMAC_CTRL ),GMC_PAUSE_OFF );
@@ -1831,9 +1829,6 @@ static int sky2_down(struct net_device * ctrl &= ~(GM_GPCR_TX_ENA |GM_GPCR_RX_ENA );gma_write16 (hw, port,GM_GP_CTRL , ctrl); -/* Make sure no packets are pending */ -napi_synchronize (&hw->napi); -sky2_write8 (hw,SK_REG (port,GPHY_CTRL ),GPC_RST_SET );/* Workaround shared GMAC reset */
@@ -1864,6 +1859,15 @@ static int sky2_down(struct net_device *sky2_write8 (hw,SK_REG (port,RX_GMF_CTRL_T ),GMF_RST_SET );sky2_write8 (hw,SK_REG (port,TX_GMF_CTRL_T ),GMF_RST_SET ); +/* Force any delayed status interrrupt and NAPI */ +sky2_write32 (hw,STAT_LEV_TIMER_CNT ,0 ); +sky2_write32 (hw,STAT_TX_TIMER_CNT ,0 ); +sky2_write32 (hw,STAT_ISR_TIMER_CNT ,0 ); +sky2_read8 (hw,STAT_ISR_TIMER_CTRL ); + +synchronize_irq (hw->pdev->irq); +napi_synchronize (&hw->napi); +sky2_phy_power_down (hw, port);/* turn off LED's */
Re: [PATCH 4/9] sky2: fix shutdown synchronization
From: Stephen Hemminger <[email protected]>
Date: Wed, 17 Jun 2009 10:30:35 -0700
Quoted 10 lines
The logic in
sky2_downwas incorrect. Receiver could report status afterrx_stopwas called.The steps need to be:
* stop new frames from being transmitted
* shut off transmit/receive logic
* synchronize with NAPI to process status info about transmitter and receiverSigned-off-by Stephen Hemminger <[email protected]>
Applied.
Re: [PATCH 4/9] sky2: fix shutdown synchronization
In reply to Stephen HemmingerHi Steven,
After applying your complete patch series, I'm still getting crashes in sky2_poll, and I can make them go away by adding an msleep(1) before these lines in sky2_down.
+ synchronize_irq(hw->pdev->irq);
+ napi_synchronize(&hw->napi);
+
sky2_phy_power_down(hw, port)
thanks,
Mike
Re: [PATCH 4/9] sky2: fix shutdown synchronization
Quoted 7 lines · On Fri, 19 Jun 2009 08:25:03 +0900 Mike McCormack <[email protected]> wrote:
Hi Steven,
After applying your complete patch series, I'm still getting crashes in
sky2_poll, and I can make them go away by adding an msleep(1) before these lines insky2_down.
adding msleep adds delay so interrupt and packets can clear, that is okay, but would rather have something deterministic? perhaps it needs to poll irq status register or napi status.
Re: [PATCH 4/9] sky2: fix shutdown synchronization
Quoted 11 lines · Stephen Hemminger
Quoted 4 lines · On Fri, 19 Jun 2009 08:25:03 +0900 Mike McCormack <[email protected]> wrote:
Hi Steven,
After applying your complete patch series, I'm still getting crashes in
sky2_poll, and I can make them go away by adding an msleep(1) before these lines insky2_down.adding msleep adds delay so interrupt and packets can clear, that is okay, but would rather have something deterministic? perhaps it needs to poll irq status register or napi status.
Well, having a check for NULL rx_ring in sky2_poll functions is a little more deterministic, but I know you don't like that :-)
Another possibility is to try reordering the shutdown, I can have a go at experimenting with that.
I have found two other potential problems:
* there appears to be a race in sky2_poll (patch attached)
* sky2_up can cause receiver hangs due to a similar race to the one in sky2_down (I have some code which stops that from happening and will try put this top of your changes and push a patch out today for your inspection)
thanks,
Mike
Quoted 1 line
From
e9a7e8c1863a998428046bf7eaf7951379645822Mon Sep 17 00:00:00 2001
From: Mike McCormack <[email protected]>
Date: Thu, 18 Jun 2009 20:37:41 +0900
Subject: [PATCH] Fix a race condition in sky2_poll
Clear interrupt only when the status buffer is fully drained, Make sure to clear interrupt when work_done == work_limit
and the buffer is drained.
--- drivers/net/sky2.c | 12 ++++++++---- 1 files changed, 8 insertions(+), 4 deletions(-)
drivers/net/sky2.c +8 -4
@@ -2524,9 +2524,6 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do, u16 idx) } }while (hw->st_idx != idx); -/* Fully processed status ring so clear irq */ -sky2_write32 (hw,STAT_CTRL ,SC_STAT_CLR_IRQ ); - exit_loop:sky2_rx_done (hw,0 , total_packets[0 ], total_bytes[0 ]);sky2_rx_done (hw,1 , total_packets[1 ], total_bytes[1 ]);
@@ -2779,9 +2776,16 @@ static int sky2_poll(struct napi_struct *napi, int work_limit)if (status &Y2_IS_IRQ_PHY2 )sky2_phy_intr (hw,1 ); -while ((idx =sky2_read16 (hw,STAT_PUT_IDX )) != hw->st_idx) { + idx =sky2_read16 (hw,STAT_PUT_IDX ); +while (idx != hw->st_idx) { work_done +=sky2_status_intr (hw, work_limit - work_done, idx); +/* If we fully processed the status ring, clear the irq */ + idx =sky2_read16 (hw,STAT_PUT_IDX ); +if (idx == hw->st_idx) { +sky2_write32 (hw,STAT_CTRL ,SC_STAT_CLR_IRQ ); +break ; + }if (work_done >= work_limit) goto done; }
Signature · 1 line
1.5.6.5
PATCH 5/9 sky2: receive counter update
In reply to Stephen HemmingerSince it is likely that there are multiple packets received per interrupt, only update the receive counters once after all packets are processed.
drivers/net/sky2.c +19 -10
@@ -2357,11 +2357,25 @@ static inline void sky2_tx_done(struct n } } +static inline void sky2_rx_done (struct sky2_hw *hw,unsigned port, +unsigned packets,unsigned bytes) +{ +if (packets) { +struct net_device *dev = hw->dev[port]; + + dev->stats.rx_packets += packets; + dev->stats.rx_bytes += bytes; + dev->last_rx = jiffies; +sky2_rx_update (netdev_priv (dev), rxqaddr[port]); + } +} +/* Process status response ring */ static int sky2_status_intr (struct sky2_hw *hw,int to_do,u16 idx) {int work_done =0 ; -unsigned rx[2 ] = {0 ,0 }; +unsigned int total_bytes[2 ] = {0 }; +unsigned int total_packets[2 ] = {0 };rmb (); do {
@@ -2388,7 +2402,8 @@ static int sky2_status_intr(struct sky2_ le->opcode =0 ;switch (opcode & ~HW_OWNER ) {case OP_RXSTAT : - ++rx[port]; + total_packets[port]++; + total_bytes[port] += length; skb =sky2_receive (dev, length, status);if (unlikely (!skb)) { dev->stats.rx_dropped++;
@@ -2406,9 +2421,6 @@ static int sky2_status_intr(struct sky2_ } skb->protocol =eth_type_trans (skb, dev); - dev->stats.rx_packets++; - dev->stats.rx_bytes += skb->len; - dev->last_rx = jiffies;#ifdef SKY2_VLAN_TAG_USED if (sky2->vlgrp && (status &GMR_FS_VLAN )) {
@@ -2487,11 +2499,8 @@ static int sky2_status_intr(struct sky2_sky2_write32 (hw,STAT_CTRL ,SC_STAT_CLR_IRQ ); exit_loop: -if (rx[0 ]) -sky2_rx_update (netdev_priv (hw->dev[0 ]),Q_R1 ); - -if (rx[1 ]) -sky2_rx_update (netdev_priv (hw->dev[1 ]),Q_R2 ); +sky2_rx_done (hw,0 , total_packets[0 ], total_bytes[0 ]); +sky2_rx_done (hw,1 , total_packets[1 ], total_bytes[1 ]);return work_done; }
Re: [PATCH 5/9] sky2: receive counter update
From: Stephen Hemminger <[email protected]>
Date: Wed, 17 Jun 2009 10:30:36 -0700
Quoted 5 lines
Since it is likely that there are multiple packets received per interrupt, only update the receive counters once after all packets are processed.
Signed-off-by Stephen Hemminger <[email protected]>
Applied.
PATCH 6/9 sky2: reduce default transmit ring
In reply to Stephen HemmingerReduce the size of the driver transmit ring to reduce latency and allow qdisc to do better rate control. Also make it obvious what the minimum transmit ring allowed is and why.
drivers/net/sky2.c +2 -2
@@ -65,9 +65,9 @@#define RX_DEF_PENDING RX_MAX_PENDING#define TX_RING_SIZE 512 -#define TX_DEF_PENDING (TX_RING_SIZE - 1) -#define TX_MIN_PENDING 64 +#define TX_DEF_PENDING 128#define MAX_SKB_TX_LE (4 + (sizeof(dma_addr_t)/sizeof(u32))*MAX_SKB_FRAGS) +#define TX_MIN_PENDING (MAX_SKB_TX_LE+1)#define STATUS_RING_SIZE 2048/* 2 ports * (TX + 2*RX) */ #define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le))
Re: [PATCH 6/9] sky2: reduce default transmit ring
From: Stephen Hemminger <[email protected]>
Date: Wed, 17 Jun 2009 10:30:37 -0700
Quoted 5 lines
Reduce the size of the driver transmit ring to reduce latency and allow qdisc to do better rate control. Also make it obvious what the minimum transmit ring allowed is and why.
Signed-off-by Stephen Hemminger <[email protected]>
Applied.
PATCH 7/9 sky2: skb recycling
In reply to Stephen HemmingerThis patch implements skb recycling. It reclaims transmitted skb's for use in the receive ring.
drivers/net/sky2.c +27 -11
@@ -1176,6 +1176,7 @@ static void sky2_rx_clean(struct sky2_po re->skb =NULL ; } } +skb_queue_purge (&sky2->rx_recycle); }/* Basic MII support */
@@ -1252,6 +1253,12 @@ static void sky2_vlan_rx_register(struct }#endif +/* Amount of required worst case padding in rx buffer */ +static inline unsigned sky2_rx_pad (const struct sky2_hw *hw) +{ +return (hw->flags &SKY2_HW_RAM_BUFFER ) ?8 :2 ; +} +/* * Allocate an skb for receiving. If the MTU is large enough * make the skb non-linear with a fragment list of pages.
@@ -1261,6 +1268,13 @@ static struct sk_buff *sky2_rx_alloc(strstruct sk_buff *skb;int i; + skb =__skb_dequeue (&sky2->rx_recycle); +if (!skb) + skb =netdev_alloc_skb (sky2->netdev, sky2->rx_data_size + +sky2_rx_pad (sky2->hw)); +if (!skb) + goto nomem; +if (sky2->hw->flags &SKY2_HW_RAM_BUFFER ) {unsigned char *start;/*
@@ -1269,18 +1283,10 @@ static struct sk_buff *sky2_rx_alloc(str* The buffer returned from netdev_alloc_skb is * aligned except if slab debugging is enabled. */ - skb =netdev_alloc_skb (sky2->netdev, sky2->rx_data_size +8 ); -if (!skb) - goto nomem; start =PTR_ALIGN (skb->data,8 );skb_reserve (skb, start - skb->data); - }else { - skb =netdev_alloc_skb (sky2->netdev, - sky2->rx_data_size +NET_IP_ALIGN ); -if (!skb) - goto nomem; + }else skb_reserve (skb,NET_IP_ALIGN ); - }for (i =0 ; i < sky2->rx_nfrags; i++) {struct page *page =alloc_page (GFP_ATOMIC );
@@ -1357,6 +1363,8 @@ static int sky2_rx_start(struct sky2_por sky2->rx_data_size = size; +skb_queue_head_init (&sky2->rx_recycle); +/* Fill Rx ring */ for (i =0 ; i < sky2->rx_pending; i++) { re = sky2->rx_ring + i;
@@ -1764,14 +1772,22 @@ static void sky2_tx_complete(struct sky2 }if (le->ctrl &EOP ) { +struct sk_buff *skb = re->skb; +if (unlikely (netif_msg_tx_done (sky2)))printk (KERN_DEBUG "%s: tx done %u\n" , dev->name, idx); dev->stats.tx_packets++; - dev->stats.tx_bytes += re->skb->len; + dev->stats.tx_bytes += skb->len; + +if (skb_queue_len (&sky2->rx_recycle) < sky2->rx_pending + &&skb_recycle_check (skb, sky2->rx_data_size + +sky2_rx_pad (sky2->hw))) +__skb_queue_head (&sky2->rx_recycle, skb); +else +dev_kfree_skb_any (skb); -dev_kfree_skb_any (re->skb); sky2->tx_next =RING_NEXT (idx,TX_RING_SIZE ); } }
drivers/net/sky2.h +1 -0
@@ -2028,6 +2028,7 @@ struct sky2_port {u16 rx_pending;u16 rx_data_size;u16 rx_nfrags; +struct sk_buff_head rx_recycle;#ifdef SKY2_VLAN_TAG_USED u16 rx_tag;
Re: [PATCH 7/9] sky2: skb recycling
From: Stephen Hemminger <[email protected]>
Date: Wed, 17 Jun 2009 10:30:38 -0700
Quoted 4 lines
This patch implements skb recycling. It reclaims transmitted skb's for use in the receive ring.
Signed-off-by Stephen Hemminger <[email protected]>
Applied.
Re: [PATCH 7/9] sky2: skb recycling
In reply to Stephen HemmingerQuoted 2 lines · Stephen Hemminger
This patch implements skb recycling. It reclaims transmitted skb's for use in the receive ring.
Was sky2 able to show any gain in forwarding performance due to this patch? Was it significant? What kind of machine was used to test?
Re: [PATCH 7/9] sky2: skb recycling
Quoted 9 lines · Jesse
Quoted 2 lines · Stephen Hemminger
This patch implements skb recycling. It reclaims transmitted skb's for use in the receive ring.
Was sky2 able to show any gain in forwarding performance due to this patch? Was it significant? What kind of machine was used to test?
no not really, sky2 has other issue which hurt performance.
PATCH 8/9 sky2: add GRO support
In reply to Stephen HemmingerAdd support for generic receive offload.
drivers/net/sky2.c +21 -8
@@ -2373,6 +2373,26 @@ static inline void sky2_tx_done(struct n } } +static inline void sky2_skb_rx (const struct sky2_port *sky2, +u32 status,struct sk_buff *skb) +{ +#ifdef SKY2_VLAN_TAG_USED +u16 vlan_tag =be16_to_cpu (sky2->rx_tag); +if (sky2->vlgrp && (status &GMR_FS_VLAN )) { +if (skb->ip_summed ==CHECKSUM_NONE ) +vlan_hwaccel_receive_skb (skb, sky2->vlgrp, vlan_tag); +else +vlan_gro_receive (&sky2->hw->napi, sky2->vlgrp, + vlan_tag, skb); +return ; + } +#endif +if (skb->ip_summed ==CHECKSUM_NONE ) +netif_receive_skb (skb); +else +napi_gro_receive (&sky2->hw->napi, skb); +} +static inline void sky2_rx_done (struct sky2_hw *hw,unsigned port,unsigned packets,unsigned bytes) {
@@ -2438,14 +2458,7 @@ static int sky2_status_intr(struct sky2_ skb->protocol =eth_type_trans (skb, dev); -#ifdef SKY2_VLAN_TAG_USED -if (sky2->vlgrp && (status &GMR_FS_VLAN )) { -vlan_hwaccel_receive_skb (skb, - sky2->vlgrp, -be16_to_cpu (sky2->rx_tag)); - } else -#endif -netif_receive_skb (skb); +sky2_skb_rx (sky2, status, skb);/* Stop after net poll weight */ if (++work_done >= to_do)
David Miller
maintainerRe: [PATCH 8/9] sky2: add GRO support
From: Stephen Hemminger <[email protected]>
Date: Wed, 17 Jun 2009 10:30:39 -0700
Quoted 3 lines
Add support for generic receive offload.
Signed-off-by Stephen Hemminger <[email protected]>
This patch was hand edited in some way, as if you took hunks from a *.rej file and directly copied them into the source yet did not remove the leading spaces that are added to *.rej files by patch.
So there were a ton of "space before tab" errors emmited by GIT. I fixed these up for you.
PATCH 9/9 sky2: version 1.23
In reply to Stephen HemmingerVersion bump.
drivers/net/sky2.c +1 -1
@@ -50,7 +50,7 @@#include "sky2.h" #define DRV_NAME "sky2" -#define DRV_VERSION "1.22" +#define DRV_VERSION "1.23"#define PFX DRV_NAME " "/*
Re: [PATCH 9/9] sky2: version 1.23
From: Stephen Hemminger <[email protected]>
Date: Wed, 17 Jun 2009 10:30:40 -0700
Quoted 3 lines
Version bump.
Signed-off-by Stephen Hemminger <[email protected]>
Applied.