Marvell Kirkwood newbie question GPIO functions
Hello everybody out there,
first off all - thanks to everyone from the u-boot community for this helpful piece of code :)
Could somebody give me a short overview of the plans regarding the u-boot port of the Kirkwood arch (e.g. Sheevaplug board)?
Currently I'm using the u-boot from git.marvell.com which has first board support for sheevaplug. I'm working on a custom hardware design but as a starting point the sheevaplug seems to work well.
Sadly there is no generic gpio support - at least I couldn't find it. Are there any plans to support a driver for this feature?
I'm willing to contribute some code if someone guides me a bit?
Thanks in advance,
Dieter
Quoted 9 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Dieter Kiermaier
Sent: Thursday, June 18, 2009 1:35 PM
To: u-boot at lists.denx.de
Subject: [U-Boot] Marvell Kirkwood newbie question GPIO functions
Quoted 8 lines
Hello everybody out there,
first off all - thanks to everyone from the u-boot community for this helpful piece of code :)
Could somebody give me a short overview of the plans regarding the u-boot port of the Kirkwood arch (e.g. Sheevaplug board)?
It's my pleasure to reply you :-)
Basic Kirkwood Soc Support patches are available on the u-boot-arm.git/next (will be mainlined soon) Sheevaplug board support patches are also submitted those are under review, you can find them here...
http://lists.denx.de/pipermail/u-boot/2009-June/054313.html
http://lists.denx.de/pipermail/u-boot/2009-June/054314.html
http://lists.denx.de/pipermail/u-boot/2009-June/054316.html
Some other board patches are in pipeline
Quoted 5 lines
Currently I'm using the u-boot from git.marvell.com which has first board support for sheevaplug. I'm working on a custom hardware design but as a starting point the sheevaplug seems to work well.
Objective for U-boot at git.marvell.com is to maintain a usable copy of u-boot with all accepted/unaccepted patches at one place to support Kirkwood developers, but once all these patches are mainlined, this repository will be removed.
Quoted 3 lines
Sadly there is no generic gpio support - at least I couldn't find it. Are there any plans to support a driver for this feature?
BTW: what you want to do at u-boot level with GPIOs?
Current Kirkwood drivers and board support does not need any specific GPIO driver, you can access registers directly to read/write GPIOs. But I think if this is a need in future, I will add gpio driver support. You can provide me your requirements too.
Quoted 2 lines
I'm willing to contribute some code if someone guides me a bit?
You are most welcomed....
Pls feel free to raise your queries...
Regards..
Prafulla . .
Quoted 9 lines
Thanks in advance,
Dieter_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Hi Prafulla,
Quoted 10 lines
It's my pleasure to reply you :-)
Basic Kirkwood Soc Support patches are available on the u-boot-arm.git/next (will be mainlined soon) Sheevaplug board support patches are also submitted those are under review, you can find them here...
http://lists.denx.de/pipermail/u-boot/2009-June/054313.html
http://lists.denx.de/pipermail/u-boot/2009-June/054314.html
http://lists.denx.de/pipermail/u-boot/2009-June/054316.htmlSome other board patches are in pipeline
thanks very much for your help.
So far I have seen that marvell git u-boot is used to push it to mainline. Great job!
What patches are in the pipeline?
Quoted 11 lines
Quoted 5 lines
Currently I'm using the u-boot from git.marvell.com which has first board support for sheevaplug. I'm working on a custom hardware design but as a starting point the sheevaplug seems to work well.
Objective for U-boot at git.marvell.com is to maintain a usable copy of u-boot with all accepted/unaccepted patches at one place to support Kirkwood developers, but once all these patches are mainlined, this repository will be removed.
Quoted 8 lines
Quoted 2 lines
Sadly there is no generic gpio support - at least I couldn't find it. Are there any plans to support a driver for this feature?
BTW: what you want to do at u-boot level with GPIOs?
Current Kirkwood drivers and board support does not need any specific GPIO driver, you can access registers directly to read/write GPIOs. But I think if this is a need in future, I will add gpio driver support. You can provide me your requirements too.
I'm working on a custom hardware using the sheevaplug as a starting point. Hopefully end of summer I finish the hardware work and have my own board. But I have some additional requirements. For example control some power supplies for LCD, boot an FPGA, program a clock chip device and so on. So my demands are:
- GPIO support (for programming the clock generator which has a simple serial ????????interface to clock in the configuration data) ????????Yeah, I know that I can setup the GPIOs by writing directly to the registers,
????????but a gpio frameworks would be much nicer ;)
- SPI (from the TDM module) support which works independet ? from NAND flash and SD-Card
I have allready posted a query to arm-linux kernel mailing list and yesterday evening I have talked with Lennert on IRC regarding SPI and linux .
The SPI interface is needed in u-boot to boot my lattice FPGA which is configured as slave serial device (and later on in linux to drive a touch controller).
There is allready a FPGA configuration framework inside u-boot and I would like to integrate also a lattice FPGA into that. But to do this I need SPI support.
Quoted 5 lines
Quoted 2 lines
I'm willing to contribute some code if someone guides me a bit?
You are most welcomed....
Pls feel free to raise your queries...
Here they are :)
Thanks,
Dieter
Quoted 10 lines
Regards..
Prafulla . .Quoted 7 lines
Thanks in advance,
Dieter_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Hi again,
Quoted 55 lines
Hi Prafulla,
Quoted 10 lines
It's my pleasure to reply you :-)
Basic Kirkwood Soc Support patches are available on the u-boot-arm.git/next (will be mainlined soon) Sheevaplug board support patches are also submitted those are under review, you can find them here...
http://lists.denx.de/pipermail/u-boot/2009-June/054313.html
http://lists.denx.de/pipermail/u-boot/2009-June/054314.html
http://lists.denx.de/pipermail/u-boot/2009-June/054316.htmlSome other board patches are in pipeline
thanks very much for your help.
So far I have seen that marvell git u-boot is used to push it to mainline. Great job!
What patches are in the pipeline?Quoted 10 lines
Quoted 4 lines
Currently I'm using the u-boot from git.marvell.com which has first board support for sheevaplug. I'm working on a custom hardware design but as a starting point the sheevaplug seems to work well.
Objective for U-boot at git.marvell.com is to maintain a usable copy of u-boot with all accepted/unaccepted patches at one place to support Kirkwood developers, but once all these patches are mainlined, this repository will be removed.
Quoted 8 lines
Quoted 2 lines
Sadly there is no generic gpio support - at least I couldn't find it. Are there any plans to support a driver for this feature?
BTW: what you want to do at u-boot level with GPIOs?
Current Kirkwood drivers and board support does not need any specific GPIO driver, you can access registers directly to read/write GPIOs. But I think if this is a need in future, I will add gpio driver support. You can provide me your requirements too.I'm working on a custom hardware using the sheevaplug as a starting point. Hopefully end of summer I finish the hardware work and have my own board. But I have some additional requirements. For example control some power supplies for LCD, boot an FPGA, program a clock chip device and so on. So my demands are:
- GPIO support (for programming the clock generator which has a simple serial interface to clock in the configuration data) ????????Yeah, I know that I can setup the GPIOs by writing directly to the registers,
????????but a gpio frameworks would be much nicer ;)- SPI (from the TDM module) support which works independet ? from NAND flash and SD-Card
I have allready posted a query to arm-linux kernel mailing list and yesterday evening I have talked with Lennert on IRC regarding SPI and linux .
Quoted 6 lines
The SPI interface is needed in u-boot to boot my lattice FPGA which is configured as slave serial device (and later on in linux to drive a touch controller).
There is allready a FPGA configuration framework inside u-boot and I would like to integrate also a lattice FPGA into that. But to do this I need SPI support.
What I forgot to mention is the i2c driver inside u-boot.
I need this to read the mac address from an additional eeprom. This makes mass production more ease and doesn't produce hight costs :)
Dieter
Quoted 25 lines
Quoted 5 lines
Quoted 2 lines
I'm willing to contribute some code if someone guides me a bit?
You are most welcomed....
Pls feel free to raise your queries...Here they are :)
Thanks,
DieterQuoted 10 lines
Regards..
Prafulla . .Quoted 7 lines
Thanks in advance,
Dieter_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Quoted 24 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Dieter Kiermaier
Sent: Friday, June 19, 2009 2:23 PM
To: u-boot at lists.denx.de
Subject: Re: [U-Boot] Marvell Kirkwood newbie question GPIO functionsHi again,
Quoted 6 lines
Hi Prafulla,
Quoted 4 lines
It's my pleasure to reply you :-)
Basic Kirkwood Soc Support patches are available on the u-boot-arm.git/next (will be mainlined soon) Sheevaplug board support patches are also submitted those are underreview, you can
Quoted 5 lines
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Some other board patches are in pipeline
thanks very much for your help.
So far I have seen that marvell git u-boot is used to pushit to mainline.
Quoted 2 lines
Great job!
What patches are in the pipeline?
Some other board supports (MV88F6281GTW_GE) and Kirkwood SPI driver support Kirkwood USB support (at this moment)
Quoted 53 lines
Quoted 7 lines
Quoted 7 lines
Quoted 5 lines
Currently I'm using the u-boot from git.marvell.com which has first board support for sheevaplug. I'm working on a custom hardware design but as a starting point the sheevaplug seems to work well.
Objective for U-boot at git.marvell.com is to maintain a
usable copy
Quoted 5 lines
Quoted 5 lines
of u-boot with all accepted/unaccepted patches at one place to support Kirkwood developers, but once all these patches are mainlined, this repository will be removed.
Quoted 1 line
Sadly there is no generic gpio support - at least I
couldn't find it.
Quoted 9 lines
Quoted 7 lines
Quoted 1 line
Are there any plans to support a driver for this feature?
BTW: what you want to do at u-boot level with GPIOs? Current Kirkwood drivers and board support does not need any specific GPIO driver, you can access registers directly to read/write GPIOs. But I think if this is a need in future, I will add gpio driver support. You can provide me your requirements too.
I'm working on a custom hardware using the sheevaplug as a
starting point.
Quoted 1 line
Hopefully end of summer I finish the hardware work and have
my own board.
Quoted 2 lines
But I have some additional requirements. For example control some power supplies for LCD, boot an FPGA, program a clock chip
device and so on.
Quoted 2 lines
So my demands are:
- GPIO support (for programming the clock generator whichhas a simple
Quoted 2 lines
serial interface to clock in the configuration data) ????????Yeah, I know that I can setup the GPIOs by writing
directly to
Quoted 8 lines
the registers,
????????but a gpio frameworks would be much nicer ;)- SPI (from the TDM module) support which works independet ? from NAND flash and SD-Card
I have allready posted a query to arm-linux kernel mailing list and yesterday evening I have talked with Lennert on IRC
regarding SPI and
Quoted 3 lines
linux .
The SPI interface is needed in u-boot to boot my lattice
FPGA which is
Quoted 3 lines
configured as slave serial device (and later on in linux to drive a touch controller).
There is allready a FPGA configuration framework insideu-boot and I
Quoted 1 line
would like to integrate also a lattice FPGA into that. But
Quoted 8 lines
to do this
Quoted 1 line
I need SPI support.
What I forgot to mention is the i2c driver inside u-boot. I need this to read the mac address from an additional eeprom. This makes mass production more ease and doesn't produce hight costs :)
Kirkwood has in-built i2c(TWSI) controller, well.. the plans are in place enable driver for it, but this is not blocking issue right now hence pending ;-)
Just FYI: you can protect some flash sector and use it in place of eeprom, this will lower the board cost and complexity too.
But if you are planning to use some different GPIOs for i2c and bit-banged driver on the top of it, then you will need gpio control, so you can do it by using simple readl/writel calls meanwhile driver to come in :-)
The best way I will suggest you is:
Put pre-programmed eeprom around Kirkwood TWSI interface and enable "TWSI serial ROM initialization" you don't need anything else for this. (I hope you are having enough kirkwood documentation)
Ref: table 32: http://www.marvell.com/files/products/embedded_processors/kirkwood/HW_88F6281_OpenSource.pdf
Regards..
Prafulla . .
Quoted 35 lines
Dieter
Quoted 21 lines
Quoted 5 lines
Quoted 2 lines
I'm willing to contribute some code if someone guides me a bit?
You are most welcomed....
Pls feel free to raise your queries...Here they are :)
Thanks,
DieterQuoted 10 lines
Regards..
Prafulla . .Quoted 7 lines
Thanks in advance,
Dieter_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootQuoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Prafulla,
(...deleted some stuff...)
Quoted 5 lines
Quoted 1 line
Quoted 1 line
What patches are in the pipeline?
Some other board supports (
MV88F6281GTW_GE) and Kirkwood SPI driver support Kirkwood USB support (at this moment)
Also very interesting :)
(...deleted, too...)
Quoted 10 lines
Quoted 5 lines
What I forgot to mention is the i2c driver inside u-boot. I need this to read the mac address from an additional eeprom. This makes mass production more ease and doesn't produce hight costs :)
Kirkwood has in-built i2c(TWSI) controller, well.. the plans are in place enable driver for it, but this is not blocking issue right now hence pending ;-)
Quoted 7 lines
Just FYI: you can protect some flash sector and use it in place of eeprom, this will lower the board cost and complexity too.
But if you are planning to use some different GPIOs for i2c and bit-banged driver on the top of it, then you will need gpio control, so you can do it by using simple readl/writel calls meanwhile driver to come in :-)
Yes, I thought about that, too. GPIO support will also be helpful for doing this!
Do you have some snippets how to readl/writel by hand?
Quoted 7 lines
The best way I will suggest you is:
Put pre-programmed eeprom around Kirkwood TWSI interface and enable "TWSI serial ROM initialization" you don't need anything else for this. (I hope you are having enough kirkwood documentation) Ref: table 32:
http://www.marvell.com/files/products/embedded_processors/kirkwood/HW_88F62
81_OpenSource.pdf
Good idea - I will read about that.
I've got access to all documents - including an marvell web account for internal documents.
Regards,
Dieter
Quoted 34 lines
Regards..
Prafulla . .Quoted 31 lines
Dieter
Quoted 20 lines
Quoted 4 lines
Quoted 1 line
I'm willing to contribute some code if someone guides me a bit?
You are most welcomed....
Pls feel free to raise your queries...Here they are :)
Thanks,
DieterQuoted 10 lines
Regards..
Prafulla . .Quoted 7 lines
Thanks in advance,
Dieter_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootQuoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Quoted 38 lines
-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Friday, June 19, 2009 3:17 PM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] Marvell Kirkwood newbie question GPIO functionsPrafulla,
(...deleted some stuff...)
Quoted 5 lines
Quoted 1 line
Quoted 1 line
What patches are in the pipeline?
Some other board supports (
MV88F6281GTW_GE) and Kirkwood SPI driver support Kirkwood USB support (at this moment)Also very interesting :)
(...deleted, too...)
Quoted 4 lines
Quoted 4 lines
What I forgot to mention is the i2c driver inside u-boot. I need this to read the mac address from an additional eeprom. This makes mass production more ease and doesn't produce
hight costs
Quoted 4 lines
Quoted 1 line
:)
Kirkwood has in-built i2c(TWSI) controller, well.. the plans are in place enable driver for it, but this is not blocking issue
right now
Quoted 7 lines
hence pending ;-)
Just FYI: you can protect some flash sector and use it in place of eeprom, this will lower the board cost and complexity too.
But if you are planning to use some different GPIOs for i2c and bit-banged driver on the top of it, then you will need gpio
control,
Quoted 8 lines
Quoted 1 line
so you can do it by using simple readl/writel calls
meanwhile driver
Quoted 2 lines
to come in :-)
Yes, I thought about that, too. GPIO support will also be helpful for doing this!
Do you have some snippets how to readl/writel by hand?
You can refer kw_config_gpio function in cpu/arm926ejs/kirkwood/cpu.c
Quoted 7 lines
Quoted 5 lines
The best way I will suggest you is:
Put pre-programmed eeprom around Kirkwood TWSI interface and enable "TWSI serial ROM initialization" you don't need anything else for this. (I hope you are having enough kirkwood documentation)Ref: table 32:
Quoted 1 line
Quoted 8 lines
kwood/HW_8
Quoted 3 lines
8F62
81_OpenSource.pdfGood idea - I will read about that.
I've got access to all documents - including an marvell web account for internal documents.
That's very good...
Regards..
Prafulla . .
Quoted 44 lines
Regards,
DieterQuoted 6 lines
Regards..
Prafulla . .Quoted 3 lines
Dieter
Quoted 1 line
Quoted 1 line
Quoted 1 line
I'm willing to contribute some code if someone
guides me a bit?
Quoted 28 lines
Quoted 28 lines
Quoted 19 lines
Quoted 3 lines
You are most welcomed....
Pls feel free to raise your queries...Here they are :)
Thanks,
DieterQuoted 10 lines
Regards..
Prafulla . .Quoted 7 lines
Thanks in advance,
Dieter_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootQuoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Quoted 47 lines
Quoted 47 lines
-----Original Message-----
From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
Sent: Friday, June 19, 2009 3:17 PM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] Marvell Kirkwood newbie question GPIO functionsPrafulla,
(...deleted some stuff...)
Quoted 4 lines
Quoted 1 line
Quoted 1 line
What patches are in the pipeline?
Some other board supports (
MV88F6281GTW_GE) and Kirkwood SPI driver support Kirkwood USB support (at this moment)Also very interesting :)
(...deleted, too...)
Quoted 3 lines
Quoted 3 lines
What I forgot to mention is the i2c driver inside u-boot. I need this to read the mac address from an additional eeprom. This makes mass production more ease and doesn't produce
hight costs
Quoted 4 lines
Quoted 1 line
:)
Kirkwood has in-built i2c(TWSI) controller, well.. the plans are in place enable driver for it, but this is not blocking issue
right now
Quoted 7 lines
hence pending ;-)
Just FYI: you can protect some flash sector and use it in place of eeprom, this will lower the board cost and complexity too.
But if you are planning to use some different GPIOs for i2c and bit-banged driver on the top of it, then you will need gpio
control,
Quoted 1 line
so you can do it by using simple readl/writel calls
meanwhile driver
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
to come in :-)
Yes, I thought about that, too. GPIO support will also be helpful for doing this!
Do you have some snippets how to readl/writel by hand?You can refer
kw_config_gpiofunction incpu/arm926ejs/kirkwood/cpu.c
I will have a look and try this, thanks for the hint!
Quoted 62 lines
Quoted 9 lines
Quoted 5 lines
The best way I will suggest you is:
Put pre-programmed eeprom around Kirkwood TWSI interface and enable "TWSI serial ROM initialization" you don't need anything else for this. (I hope you are having enough kirkwood documentation)Ref: table 32:
Quoted 8 lines
kwood/HW_8
Quoted 2 lines
8F62
81_OpenSource.pdfGood idea - I will read about that.
I've got access to all documents - including an marvell web account for internal documents.That's very good...
Regards..
Prafulla . .Quoted 39 lines
Regards,
DieterQuoted 6 lines
Regards..
Prafulla . .Quoted 3 lines
Dieter
Quoted 1 line
Quoted 1 line
Quoted 1 line
I'm willing to contribute some code if someone
guides me a bit?
Quoted 27 lines
Quoted 27 lines
Quoted 18 lines
Quoted 2 lines
You are most welcomed....
Pls feel free to raise your queries...Here they are :)
Thanks,
DieterQuoted 10 lines
Regards..
Prafulla . .Quoted 7 lines
Thanks in advance,
Dieter_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootQuoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot